Grandstream Networks GDS3710 Hemispheric HD IP Video Door Phone User Manual

Grandstream Networks, Inc. Hemispheric HD IP Video Door Phone

UserManual.wiki >

Grandstream Networks >

GDS3710 User Manual

User manual

Network Protocol TCP/IP/UDP, RTP/RTCP, HTTP/HTTPS, ARP/RARP, ICMP, DNS (A record, SRV, NAPTR), DHCP, PPPoE, SSH, SMTP, TFTP, NTP, STUN, SIMPLE, LLDP-MED, LDAP, 802.1x, TLS, SRTP SIP/VoIP Support Broad interoperability with most 3rd party SIP/VoIP devices and leading SIP/NGN/IMS platforms Voice Codecs G.711µ/a-law, G.722, in-band and out-of-band DTMF (in audio, RFC2833, SIP INFO), AEC QoS Layer 2 QoS (802.1Q, 802.1P) and Layer 3 QoS (ToS, DiffServ, MPLS) Security User and administrator level access control, MD5 and MD5-sess based authentication, 256-bit AES encrypted configuration file, TLS, SRTP, HTTPS, 802.1x media access control Upgrade/ Provisioning Firmware upgrade via TFTP/HTTP/HTTPS, mass provisioning using TR-069 (Pending) or AES encrypted XML configuration file Audio Input Built-in digital microphone, up to 1.5m with good AEC Audio Output Built-in HD loudspeaker, up to 3m with good loudness Button 12-key touchpad plus a capacitive doorbell button, each with individual LED illumination RFID 125KHz: ISO1 4223, ISO18000-2 (2 RFID cards included) Motion Sensor Yes, built-in Infrared tube with detection range of 0.5 m Alarm Input Yes, 2 channels, Vin < 15V, for door sensor or other devices Alarm Output Yes, 2 channels, 125VAC/0.5A, 30VDC/2A, Normal Open or Normal Close, for electric lock, light switch or other devices Network Interface 10M/100M auto-sensing Expansion Interface RS485, Wiegand input and output Weight 0.6Kg Package Content Base unit, Ethernet cable, Quick Start Guide, Screwdriver Dimensions (H x W x D) 173mm(H) x 80mm(W) x 36mm(D) Power Supply PoE IEEE 802.3af Class 3, or 12VDC/1A connection (AC power adapter not included) Ingress Protection Weather proof, vandal resistant, with support for extra back reinforcing metal plate Temperature and Humidity Operation: -30°C to 55°C (-22°F to 131°F) Storage: -35°C to 60°C (-31°F to 140°F) Humidity: 10% to 90% Non-condensing

Appendix I: Cable Wiring on Rear Panel Jack Pin Signal Function J2 (basic) 3.81mm 1 TX+ Ethernet, PoE 2 TX- 3 RX+ 4 RX- 5 POE_SP2 6 POE_SP1 7 RS485_B RS485 8 RS485_A 9 GND Power Supply 10 12V J3 (advanced) 3.81mm 1 GND Alarm Ground 2 ALARM1_IN+ Alarm In 3 ALARM1_IN- 4 ALARM2_IN+ 5 ALARM2_IN- 6 NO1 Alarm Out 7 COM1 8 NO2 9 COM2 10 NC2 J4 (special) 2.00mm 1 GND Wiegand Out 2 WG_D1_OUT 3 WG_D0_OUT 4 LED Wiegand In 5 WG_D1_IN 6 WG_D0_IN 7 BEEP 8 5V Wiegand Power

Appendix II: Rear Panel Installations

EU Compliance Statement: The device complies with EU EMF Directive 1999/519/EC can be used in the European Community. “Hereby, (Grandstream Networks, Inc.), declares that this (Model:GDS3710) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.” FCC Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Important: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. RF Exposure: This equipment complies with FCC’s and Europe's RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users.