Graupner and KG 33516 Receiver GR-32 HoTT User Manual Kurzanleitung HoTT 33516 en indd

Download:
Mirror Download [FCC.gov]
Document ID	1552090
Application ID	dgS9UBW4pH8N/wakIxg+Ng==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.98kB (174768 bits)
Date Submitted	2011-09-29 00:00:00
Date Available	2011-09-29 00:00:00
Creation Date	2011-09-21 11:34:38
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-09-21 11:34:38
Document Title	Kurzanleitung_HoTT_33516_en.indd
Document Creator	PScript5.dll Version 5.2
Document Author:	wbergbauer

Manual
33516
Receiver GR-32 HoTT
CONTENTS:
1. General Note .............................................................................................................. 01
2. Functions.................................................................................................................... 01
2.1. Binding ......................................................................................................................... 01
2.2. Binding Multiple Receivers .......................................................................................... 01
2.3. Fail-Safe Function........................................................................................................ 02
3. Receiver ...................................................................................................................... 02
3.1. Connections ................................................................................................................. 02
3.2. Low Voltage Warning ................................................................................................... 03
3.3. Temperature Warning .................................................................................................. 03
4. Firmware Update........................................................................................................ 03
4.1. Receiver ...................................................................................................................... 03
4.2. Update Procedure........................................................................................................ 03
5. Declaration of Conformity......................................................................................... 05
6. FCC Information..........................................................................................................06
7. Warranty ..................................................................................................................... 08
Manual V1.0
Revision: September 2011
GRAUPNER GmbH & Co. KG – Postfach 1242 – 73230 Kirchheim/Teck – www.graupner.de
Thank you for purchasing the Graupner HoTT 2.4 System Please read through this entire manual before
you attempt the installation and usage of your Graupner HoTT 2.4 System!
A hardware antenna diversity system always switches to the better antenna signal and for transmission
always uses the antenna that was last used for receiving. This ensures that the back channel data
are always sent via the better-positioned antenna. Without additional sensor systems, the parameters
receiver voltage and temperature, as well as signal strength are transmitted. Connector for one telemetry sensor and for the sum signal input or output. The receiver does have 6 power inputs for strong
servos.
These operating instructions are part of this product. They contains important notes to the operation and
handling. Please take this into consideration when you pass on the product to third parties. Neglect of
the operating instructions and the safety instructions lead to expiring the warranty.
Graupner constantly work on the advancement of all remote control systems; changes of the scope of delivery in form, technology and equipment we must reserve ourselves therefore. Please have understanding
for the fact that from data and illustrations of this operating instructions no requirements can be derived.
Please keep these instructions for further reference!
1. GENERAL NOTE
When switching on or adjusting the radio control system it is essential to keep the transmitter aerial at
least 15 cm away from the receiver aerials at all times. If the transmitter aerial is too close to the receiver
aerials, the receiver will be overloaded, causing the green LED starts flashing. The transmitter responds
by emitting a beep once every second; the red LED also goes out. The radio control system is now in
Fail-Safe mode.
If this should occur, simply increase the distance between the aerials until the audible warning signal
ceases, and the red LED on the transmitter lights up again; at the same time the green LED on the
receiver should glow constantly.
2. FUNCTIONS
2.1. Binding
When you wish to use the Graupner HoTT 2.4 GHz receiver with a particular transmitter, the first step
must always be to “bind” the unit to “its” Graupner HoTT 2.4 GHz RF module (transmitter). This “binding”
procedure only needs to be carried out once for each combination of receiver and RF module. The units
supplied in the set are already bound to each other at the factory, i.e. the binding procedure described in
the following section only needs to be carried out when you wish to use an additional receiver. However,
it can also be repeated at any time if required, e.g. after changing transmitters. When binding is required,
this is the procedure:
• Switch the transmitter and receiver on.
• Locate the BIND / RANGE button on the back of the transmitter, and hold it pressed in while you
press and hold the SET button on the receiver. Both LEDs on the back of the transmitter now glow
constantly, and the red LED on the receiver flashes.
• If the red LED expires and the green LED on the receiver begins to glow permanently within about
ten seconds, this indicates that the binding process is complete. You can now release both buttons,
and your transmitter / receiver combination is ready for use.
• However, if the green LED on the receiver continues to flash for longer than ten seconds, then the
binding process has failed. If this should occur, repeat the whole procedure.
2.2. Binding“ multiple receivers in one model
If required, it is also possible to bind multiple receivers to the transmitter for a particular model. The first
step is to bind each receiver individually using the procedure already described.
When the system is in use, the receiver which was bound last is the Master receiver (which is switched
01
Manual Receiver GR-32 Graupner HoTT 2.4
on first for the modules Order No. 33300, 33301 and 33302). Any telemetry sensors installed in the
model must be connected to this unit, as only the Master receiver transmits sensor
data using the downlink channel. The second and all further receivers operate in parallel with the Master
receiver but in Slave mode, with the downlink channel switched off.
The control functions can also be distributed amongst multiple receivers; this is carried out using the
Channel Mapping function of the SMART-BOX (Order No. 33700). In the same way it is possible to assign one control function to multiple receiver outputs; a typical example would be the use of two servos
for each aileron instead of only one, etc.
2.3. Fail-Safe function
In its default state (as delivered) the receiver is set to “Hold” mode, i.e. if a fail-safe situation occurs, all
the servos connected to it maintain the last position detected as valid. In this mode the green LED on
the receiver starts flashing when interference occurs, and the red LED on the transmitter goes out. The
transmitter also starts beeping about once per second as an audible warning.
You can exploit the safety potential of the fail-safe option by at least programming the throttle channel to
respond to a fail-safe situation: the throttle channel of an engine-powered model should be set to idle,
the throttle channel of an electric-powered model to “stop”, and the throttle channel of a model helicopter
to “Hold”. If interference should occur, these settings will help prevent the model flying out of control,
possibly causing personal injury or property damage.
Please refer to the appropriate section in your RC system instructions for the procedure.
3. RECEIVER
Battery socket „B“
Servo sockets
7-12/15-16
Battery socket „B“
Battery socket „B“
Socket for
sum signal „S“
Servo sockets
1-6/13-14
Battery socket „B“
3.1 Connections
Plug the servos into the row of sockets on both sides of the receiver. The connector system is polarised;
note the small chamfer on one edge. Never use force - the plugs should engage easily and fully. The
socket polarity is also marked on the case: brown wire (-), red (+) and orange (signal).
The servo sockets of the Graupner-HoTT 2.4 receiver are numbered. It is also possible to program
socket „S“ for the sum signal using the SMART-BOX (Order No. 33700). This is important for certain
optional devices which require this signal.
Power supply
The sockets marked “- +/B” are intended only for the battery connection. Connect the power supply
preferably with the socket(s) that are close to the servos. When using High Power servos you may use
all battery connectors depending on the battery power.
Telemetry
The socket marked “T” is intended for the optional telemetry sensors and is used for loading firmware
updates in conjunction with the USB interface.
Telemetry socket
(socket „T“)
Manual Receiver GR-32 Graupner HoTT 2.4
02
3.2. Low voltage warning
If the receiver voltage falls below 3.8 V, the transmitter’s RF module generates a low voltage warning in
the form of a “general alarm sound”: a steady beeping at intervals of about one second.
3.3. Temperature warning
If the receiver temperature falls below -10° C or exceeds +70° C, the transmitter’s RF module generates
a temperature warning in the form of a “general alarm sound”: a steady beeping at intervals of about
one second.
4. FIRMWARE UPDATE
Firmware updates for the receiver can be transferred via the socket „T“ in conjunction with a PC running
Windows XP, Vista or 7. For this you also require the USB interface, Order No. 7168.6, and the adapter
lead, Order No. 7168.6A, which are available separately.
The programs and files required for this are available from www.graupner.de in the Download area for
the corresponding products.
Install the Firmware Update Utility Graupner and the USB drivers on your computer. Check the system
requirements!
The first step is to cut through the central red wire in the adapter lead,
Order No. 7168.6A, then connect the lead to the USB interface, Order
No. 7168.6. This socket is also polarised; note the small chamfer on one
edge. Never use force - the plug should engage easily and fully.
4.1. Receiver
Connect the adapter lead to the socket „T“ of the receiver, as shown in the
illustration. This socket is also polarised; note the small chamfer on one
edge. Never use force - the plug should engage easily and fully.
4.2. Update procedure
Ensure that the adapter lead is configured as shown in the illustrations, and is connected correctly to
the transmitter or receiver.
Start the Graupner Firmware Update Utility.
Under [COM Port Setup] select the correct COM port, i.e. the
one to which the USB lead is connected. If you are not sure of
this, press the button „Search“ and select in the pop-up window
„Silicon Labs CP210x USB to UART Bridge“ and press „OK“.
Baud Rate: 19200.
Under [Interface Type] click on Signal 2:Vcc3:Gnd.
Now click on the “Browse” button and select the folder containing the previously loaded firmware file ending in *.bin. If
everything is correct, the file will appear in the corresponding
window.
The firmware files are encoded in product-specific form, i.e. if
you accidentally select a file which does not match the product
(e.g. transmitter update file instead of receiver file), then the pop-up window “Product code error” will
appear, and you will not be able to start the update procedure.
03
Manual Receiver GR-32 Graupner HoTT 2.4
Press the “Program” button in the software. Wait briefly until you see movement in the progress bar. This
make take up to five seconds, depending on the computer.
Receiver: press the SET button, and switch the receiver on while you hold it pressed in.
After a few seconds the Status screen displays the message “Found target device…”; you can now
release the button, and the firmware update process commences.
If the device is not recognised, if the pop-up window “Target device ID not found” appears, or if the process fails before 100%
is reached, you must restart the update procedure. Repeat all
the steps as described above.
The Status display and the Progress bar show the progress of
the firmware update. The update is completed when the message “Complete…100%” or “Complete!!” appears.
During the update process both LEDs on the transmitter glow
constantly. When it is complete, the red LED goes out and you
will hear a brief confirmation melody. The green LED on the
receiver also light up; when the process is complete, the green
LED starts flashing.
Switch your transmitter / receiver off, and disconnect the adapter lead.
Caution: after completing an update process, you must initialise the device before using it, i.e. reset it to the factory
default values.
Initialisation:
Press and hold the SET button on the receiver and switch it on, the red and green LED‘s are blinking.
After about three seconds the LED‘s expires, release now the SET button.
Please note:
The initialisation procedure erases ALL the settings you have entered. Where necessary, you will need
to program your preferred settings again.
When initialisation is complete, the transmitter will be in Fail-Safe set-up mode. You can therefore immediately continue by programming your fail-safe settings.
If you previously set your transmitter’s Country setting to “France” mode, you must also re-enter the
Country setting.
Please refer to the appropriate section in your RC system instructions for the procedure.
Any settings you have entered using the SMART-BOX are also lost when you initialise the receiver. If you carry out a receiver firmware update, you will need to re-enter these settings.
The latest version of these instructions can be found at www.graupner.de
Manual Receiver GR-32 Graupner HoTT 2.4
04
FCC INFORMATION
Graupner GR-32 HoTT #33516
FCC ID: ZKZ-33516
FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void
the user‘s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator
and your body.
Manual Receiver GR-32 Graupner HoTT 2.4
06
ENVIRONNEMENTAL PROTECTION NOTES
When this product comes to the end of its useful life, you must not dispose of it in the ordinary domestic waste. The correct method of disposal is to take it to your local collection
point for recycling electrical and electronic equipment. The symbol shown here, which may
be found on the product itself, in the operating instructions or on the packaging, indicates
that this is the case.
Individual markings indicate which materials can be recycled and re-used. You can make
an important contribution to the protection of our common environment by re-using the product, recycling the basic materials or recycling redundant equipment in other ways.
Remove batteries from your device and dispose of them at your local collection point for batteries.
In case of R/C models, you have to remove electronic parts like servos, receiver, or speed controller
from the product in question, and these parts must be disposed of with a corresponding collection point
for electrical scrap.
If you don’t know the location of your nearest disposal centre, please enquire at your local council office.
07
Manual Receiver GR-32 Graupner HoTT 2.4
This product is / Sur ce produit nous accordons une
Wir gewähren auf dieses Erzeugnis eine /
24
Garantie von
warrantied for
garantie de
Die Fa. Graupner GmbH & Co. KG, Henriettenstraße 94-96,
73230 Kirchheim/Teck gewährt ab dem Kaufdatum auf
dieses Produkt eine Garantie von 24 Monaten. Die Garantie gilt nur für die bereits beim Kauf des Produktes vorhandenen Material- oder Funktionsmängel. Schäden, die auf
Abnützung, Überlastung, falsches Zubehör oder unsachgemäße Behandlung zurückzuführen sind, sind von der
Garantie ausgeschlossen. Die gesetzlichen Rechte und
Gewährleistunsansprüche des Verbrauchers werden durch
diese Garantie nicht berührt. Bitte überprüfen Sie vor einer Reklamation oder Rücksendung das Produkt genau
auf Mängel, da wir Ihnen bei Mängelfreiheit die entstandenen Unkosten in Rechnung stellen müssen.
Graupner GmbH & Co. KG, Henriettenstraße 94-96, 73230
Kirchheim/Teck, Germany guarantees this product for a period of 24 months from date of purchase. The guarantee
applies only to such material or operational defects witch
are present at the time of purchase of the product. Damage due to wear, overloading, incompetent handling or the
use of incorrect accessories is not covered by the guarantee. The user´s legal rights and claims under garantee are
not affected by this guarantee. Please check the product
carefully for defects before you are make a claim or send
the item to us, since we are obliged to make a charge for
our cost if the product is found to be free of faults.
La société Graupner GmbH & Co. KG, Henriettenstraße
94-96, 73230 Kirchheim/Teck, Allemagne, accorde sur ce
produit une garantie de 24 mois à partir de la date d´achat.
La garantie prend effet uniquement sur les vices de fonction-nement et de matériel du produit acheté. Les dommages dûs à de l´usure, à de la surcharge, à de mauvais
accessoires ou à d´une application inadaptée, sont exclus de la garantie. Cette garantie ne remet pas en cause les droits et prétentions légaux du consommateur.
Avant toute réclamation et tout retour du prouit, veuillez
s.v.p. cotrôler et noter exactement les défauts ou vices.
Monaten
months
mois
Servicestellen / Service / Service après-vente
Graupner-Zentralservice
Graupner GmbH & Co. KG
Henriettenstrasse 94-96
D-73230 Kirchheim / Teck
Servicehotline
(+49) 01805 47 28 76
Montag - Freitag 7:30 -11:45
und 12:30 -16:00 Uhr
Belgie/Nederland
Jan van Mouwerik
Slot de Houvelaan 30
NL 3155 Maasland VT
(+31)10 59 13 59 4
Luxembourg
Kit Flammang
129, route d’Arlon
L 8009 Strassen
(+35) 23 12 23 2
Ceská Republika/Slovenská
Republika
RC Service Z. Hnizdil
Letecka 666/22
CZ-16100 Praha 6 - Ruzyne
(+42) 2 33 31 30 95
Schweiz
Graupner Service Schweiz
CD-Electronics GmbH
Kirchweg 18
CH-5614 Sarmenstorf
(+41) 56 66 71 49 1
Espana
Anguera Hobbies
C/Terrassa 14
E 43206 Reus (Tarragona)
(+34) 97 77 55 32 0
Sverige
Baltechno Electronics
P.O. Box 5307
S 40227 Göteborg
(+46) 31 70 73 00 0
France
Graupner Service France
Gérard Altmayer
86, rue St. Antoine
F 57601 Forbach-Oeting
(+33) 3 87 85 62 12
UK
Graupner Service UK
Brunel Drive
GB, NEWARK, Nottinghamshire
NG242EG
(+44) 16 36 61 05 39
Italia
GiMax
Via Manzoni, no. 8
I 25064 Gussago
(+39) 30 25 22 73 2
Garantie-Urkunde
Warranty certificate / Certificate de garantie
33516 Receiver GR-32
Übergabedatum
Date of purchase/delivery
Date de remise
Name des Käufers
Owner´s name
Nom de I`achateur
Straße, Wohnort
Complete adress
Domicie et rue
Manual Receiver GR-32 Graupner HoTT 2.4
Firmenstempel und Unterschrift
des Einzelhändlers
Stamp and signature of dealer
Cachet de la firme et signature
du detailant
08
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
09
Manual Receiver GR-32 Graupner HoTT 2.4
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
________________________________________________________________________
Manual Receiver GR-32 Graupner HoTT 2.4
10
Graupner GmbH & Co. KG
Henriettenstraße 94 – 96
D-73230 Kirchheim/Teck
Germany
www.graupner.de
Änderungen sowie Liefermöglichkeiten vorbehalten. Lieferung durch den Fachhandel. Bezugsquellen
werden nachgewiesen. Für Druckfehler kann keine Haftung übernommen werden.
Specifications and availability subject to change. Supplied through specialist model shops only. We will
gladly inform you of your nearest supplier. We accept no liability for printing errors.
Sous réserve de modifications et de possibilité de livraison. Livraison uniquement au travers de magasins spécialisés en modélisme. Nous pourrons vous communiquer l’adresse de votre revendeur le plus
proche. Nous ne sommes pas responsables d’éventuelles erreurs d’impression.
Con riserva di variazione delle specifiche e disponibilità del prodotto. Fornitura attraverso rivenditori
specializzati.Saremmo lieti di potervi indicare il punto vendita più vicino a voi. Si declina qualsiasi responsabilità per errori di stampa.
HoTT 1.0 / September 2011 - EN V1.0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
GTS PDFX Version                : PDF/X-3:2002
Producer                        : Acrobat Distiller 7.0 (Windows)
Create Date                     : 2011:09:21 11:34:38+08:00
Modify Date                     : 2011:09:21 11:34:38+08:00
Metadata Date                   : 2011:09:21 11:34:35+08:00
Creator Tool                    : PScript5.dll Version 5.2
Document ID                     : uuid:FAB195A002E4E01193E2F7C9F3E8C283
Instance ID                     : uuid:0b37929d-429b-4354-8d33-d49ab44ef566
Derived From Instance ID        : uuid:c3a1db32-7b97-40f6-a86d-1e04a6addea0
Derived From Document ID        : uuid:8f28bbcd-e25b-41d7-82fd-90b4bdd80ad4
Format                          : application/postscript
Title                           : Kurzanleitung_HoTT_33516_en.indd
Creator                         : wbergbauer
Page Count                      : 11
Author                          : wbergbauer

EXIF Metadata provided by EXIF.tools