Gree ETAC 07HC230V20A A User Manual PACKAGE UNIT Manuals And Guides 1203305L

User Manual: Gree ETAC-07HC230V20A-A ETAC-07HC230V20A-A GREE PACKAGE UNIT - Manuals and Guides View the owners manual for your GREE PACKAGE UNIT #ETAC07HC230V20AA. Home:Heating & Cooling Parts:Gree Parts:Gree PACKAGE UNIT Manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

Instal

NOTE

TO EQUIPMENT

OWNER:

Thank you for purchasing a Gree E-TAC. Please read this Owner's Information
before installing and using this appliance. Keep this manual for future reference.

Manual carefully

For your convenience, please record the model and serial numbers of your new equipment in the
spaces provided. This information, along with the installation data and dealer contact information,
will be helpful should your system require maintenance or service.

UNIT INFORMATION

DEALERSHIP

Model

Company Name:

Serial

Address:

INSTALLATION
Date

Installed

INFORMATION

CONTACT

Phone Number:
Technician Name:

INFORMATION

TABLE

OF CONTENTS
PAGE

SAFETY CONSIDERATIONS

...........................................................................

GENERAL INFORMATION .............................................................................
UNIT FEATURES
ELECTRICAL

..................................................................................

4- 5

DATA ..................................................................................

INS'FALLATION
Chassis Installation .............................................................................

Retrofit Sleeve Preparation

.......................................................................

Installation of"Gree Wall Sleeve Using Non-Gree Grille .................................................

Insta11Unit Into Wall Sleeve ......................................................................

SYSTEM

CONFIGURATION
Ventilation Control

............................................................................

Adjusting Air Direction .........................................................................

Dipswitches ..................................................................................

Keypad Configuration

..........................................................................

AUXILIARY CONTROLS
Wall Thermostat Terminal

......................................................................

Energy Management Input

......................................................................

Intelligent Self-Checking
OPERATION

Control .................................................................

........................................................................................

CARE AND CLEANING ...............................................................................

PREVENTATIVE

MAINTENANCE

TROUBLESHOOTING
WARRANTY

NOTE:

......................................................................

.............................................................................

18-22

.....................................................................................

Warranty

coverage

documented

on back

23 - 24

page of owners

manua!

UNIT INSPECTION
Examine

unit

company

if damage

for

damage

incurred

is found.

during

shipment.

File

a claim

immediately

with

the

transit

READ
SAFETY
Recognize

ALL INSTRUCTIONS

BEFORE

This is the safety-alert

symbol _. When you see this symbol on the unit and
in instructions
or manuals, be alert to the potential for
personal injury.
Understand
these
signal
words:
DANGER,
WARNING,
and CAUTION.
These words are used
with the safety=alert symbol. DANGER identifies the
most serious hazards which will result in severe
personalinjury
or death. WARNING signifies hazards
which could result in personal
injury or death.
CAUTION is used to identify unsafe practices which
may result in minor personal injury or product and
property
damage.
NOTE
is used to highlight
suggestions
which
will
result
in
enhanced
installation,
reliability,
or operation.

Thank you for choosing the Gree E-TAC! You can
feel confident in your selection because of the pride
in craftsmanship
and engineering
knowledge
that
goes into this equipment.
Gree package
terminal
air conditioners
and heat
pumps
provide
a high standard
of quality
in
performance,
workmanship,
durability
and
appearance
as they heat and cool the occupied
air
space year round.
This manual
provides
information
for
installation,
operation and maintenance.

YOU

IMPORTANT:
AND/OR PROPERTY
HAZARD

Failure to %llow this warning
death and/or property damage.

could

DAMAGE

result in personal

inspector's

injury,

For your safety, the information
in this manual
must be
fbllowed
to minimize
the risk of fire or explosion,
electric
shock, or to prevent property damage, personal injury, or loss
of life.
*

This unit must be properly installed in accordance
with the Installation Instructions
before it is used.
Immediately

repair

cords

have

that

or replace
become

all

frayed

electric
or

service

damaged.
*

Unplug

or disconnect

circuit breaker

before

the unit
making

at the fuse box

NOTE

any repairs.

NOTE: We strongly recommend
that any servicing
be performed by a qualified individual.

Save

completely
these

and carefully.

instructions

for local

use.

IMPORTANT:
ordinances.

Observe

aH governing

codes

and

TO INSTALLER

Be sure to leave these instructions

NOTE

otherwise

BEGIN

Read these instructions
INJURY

ease

All models
are designed
for through-the-wall
installatiom
Separate
installation
instructions
are
included with all accessory components.
BEFORE

PERSONAL

OR USE

GENERAL

CONSIDERATIONS
safety information.

INSTALLATION

with the owner.

TO OWNER

Keep these instructions
for future reference.
Be sure
to write down the model and serial number of unit on
space provided on front page. The model and serial
number can be located on the serial number plate
attached to unit.

UNIT

FEATURES
below the room temperature
setting regardless of fan
mode selection. Dry mode should not be considered a
substitute for a stand alone dehumidifier.
* Compressor
Protection
= To prevent short cycling
of the compressor
and maximize it's life, there is a
random
start=up
delay
of
3
minutes
on the
compressor and a minimum compressor run time of 3
minutes.

Fig. 2 - E-TAC

Front

* Automatic room freeze protection
- automatically
will keep the temperature
in the room from getting
too cold, -where water pipes might freeze. If the unit
is configured
for the freeze protection
feature to be

Panel

This E-TAC
has many
exciting
features
which
are different
than those found on standard
PTAC
models.
The owner must be familiar
with these
features in order to fully understand
capability of the unit.

the operation

and

* Intelligence
- Your E-TAC unit has an on board
computer that utilizes real time diagnostics to prolong
the life of your unit. There is an LED indicator on the
control board, behind the front panel, that will flash
an error code if the unit has detected some kind of
fault
condition.
In many
cases,
the unit will
automatically
clear the fault condition and continue
operating
with no interruption.
In some cases, the
condition cannot be cleared and the unit will require
service. In those cases, an "Fx" failure mode will be
displayed on the digital display. For a detailed list of
all error codes and "Fx" conditions,
see Table 6 =
Stattts LED Indicator

D@'nitions

for further

details.

* Memory - Your E-TAC unit also has memory. If
power is lost, all of the control settings (setpoint,
mode,
fan speed,
on/off and configuration)
are
remembered.
So when power is restored, the unit -will
start back up in the mode (and configuration)
it was
in, when power was lost.
* Premium

Sound - Your Premium

quietest PTAC ever. Not only
motors and a tangential
blower

E-TAC is also the

does it have 2 fan
wheel for optimum

sound, the indoor fan will always run a minimum of 10
seconds before the compressor,
to help reduce any
compressor starting noise.
* Random
Compressor
restart
= To help prevent
power surges after a power outage (from many of
your E=TACs starting
at the same
time),
the
compressor
is equipped with a 2:45 to 3:15 random
restart delay feature. Whenever the unit is plugged in,
or power has been restarted,
a random compressor
restart will occur.
* Dry Mode - will help to manage and reduce the
humidity in the room, making it more comfortable. In
DRY mode, the unit will modulate cooling mode at
low fan speed until the room temperature is 4 deg. F

active (which is the default condition), then-whenever
power is supplied
to the unit, if the unit senses
temperature
below 40°F (4.4°C), the fan motor and
electric heater are turned on and -will warm the room
to 50 ° F (10°C). If Freeze protection
is not required,
change the configuration
switch to turn the feature off
(see section on unit configuration).
° Automatic
defrost
protection
(for heat pump
models only) - When the outdoor temperature
gets
too cold (approx. 40°F / 4.4°C) and the unit can no
longer effectively heat with the compressor,
the unit
will automatically
switch to electric heating. The unit
will then heat with electric heat until the outside
temperature
rises enough (approx.
the compressor
can be used again.
* Automatic
models only)

40°F / 4.4°C),

Quick Warm-up
(for
= If the room temperature

heat pump
falls to 5°F

(2.8°C) below the set point temperature,
the reverse
cycle heat is shut off and the electric strip heat is
turned on for one cycle, until heating is satisfied.
* LED Indicator's
and Buttons
= The touch pad has
buttons
for
MODE,
FAN SPEED,
ON/OFF,
SETPOINT
UP and SETPOINT
DOWN. It also has
LEDs that correspond
to the mode, fan speed and
setpoint operation,
to indicate the unit's status. The
LEDs below the mode button, FAN, COOL, and
HEAT, indicate what operating mode is active. The
LEDs below the Fan button,
Low, Med and Hi,
indicate
the fan speed that is selected.
The LED
located in the lower right corner is the unit On/Off
status LED. if the unit is in ON mode, the LED will
be green, if the unit is OFF, the LED will be red.
* Configure
Fan to Optimize Selected Application
Unit can be optimized
to selected application
by
configuring the fan to run in continuous mode or cycle
on and off with the compressor and electric heater (can
be different for both heating and cooling modes). In
cycle mode, fan will continue to run 60 seconds after
compressor
or electric heater stops in order blow off
any residual heat or cool left on coil.

UNIT

FEATURES

CONTINUED

* Unit Configuration
= There are many different
configuration
possibilities,
through both dipswitches
and the digital keypad, that allow you to configure
the unit for your exact application.
See section on
unit configuration
for more details. Following are the
configuration
selections that have not previously been
mentioned:
* Fahrenheit
°F or Celcious
in either °F or °C.
* Indoor Temperature
the room temperature
application

* Limit
the Setpoint
Range
= The unit can be
configured to limit the controlling setpoint range. The
display will always show the complete setpoint range,
but the controlling
setpoint will be limited to the
configured minimum and maximum setpoint selected.
See section on unit configuration
for more details.
* Energy
Management
= Sometimes
known
as
Front Desk Control, an input is provided so that the
unit can be manually
disabled
from a different
location. If the unit detects 24vac on this input, it will
automatically
turn itself off. If no voltage is detected
on the input, the unit will run normally.
* Wall
Thermostat
Control
= A wired
wall

°C = The unit can display

Sensor Biasing = Optimize
sensor reading to your exact

(one for cooling and another

for heating).

* Emergency
Heat (for Heat Pump Only) = Disable
the compressor
during heating mode operation (heat
only with Electric Heat).

thermostat

* Display Setpoint
or Room Temperature
= The
unit can be configured
to display
the room
temperature
OR setpoint only, during heating and
cooling modes. See section on unit configuration
for
more details.

ETAC

SeriesETAC
Designation

can be connected

unit must be configured
section on wired inputs
more details.

230V

to the unit. if it is, the

to disable the keypad.
and unit configuration

-A
Environmental Protection
A- Standard Protection
C - Sea Coast Protection

Revision Level
Cooling Capacity
07 - 7,000 BTUH
09 - 9,000 BTUH
12 - 12,000 BTUH
15 - 15,000 BTUH

Electric Heat Capacity
15-2 KW
20 - 3 KW
30 - 5 KW

Model Type
HP -Heat Pump
HC - Heat/Cool

Electrical Rating
230V -208/230V 60Hz IPH
265V-265V 60Hz IPH
Fig. 3 = Catalog

Number

Nomenclature

See
for

ELECTRICAL

DATA
Groundin_

ELECTRICAL

SHOCK

For safety and protection,
the unit is grounded
through the service cord plug or through separate
ground wire provided on hard wired units. Be sure
that the branch circuit or general purpose outlet is
grounded.

HAZARD

Failure to follow this warning
injury or death and/or property

could result
damage

in personal

DO NOT alter cord or plug or use an extension

cord.

VOLTAGE

SUPPLY

IMPORTANT:
For 265V units, if power
cord
accessory option is selected, the cord is only 18 inches
long and must plug into the accessory
electrical
265V subbase.

Check voltage
supply at outlet. For satisfactory
results, the voltage range must always be within the
ranges found on the data information
plate.
Cord-connected
Units

Be sure that your outlet matches the appropriate blade
configuration
of the plug and that it is within reach of
the service cord.

The 208/230-v field supplied outlet must match the plug
for the standard 208/230-v
units and be within reach
of the service cord. The standard
cord-connected

All wiring, including
installation
of the receptacle,
must be in accordance with the NEC and local codes,
ordinances
and regulations.
National codes require
the use of an arc fault or leakage current detection
device on all 208/230V power cords. Be sure to select
the correct cord for your installation.

265-v units require an accessory electrical subbase
for operation.
Refer to Table 2 for proper receptacle
and fuse type.
Power Cord Protection

ALL

Power to the unit can be restored
button on plug head.

UNITS

Wire Size

The power cord for 208/230v units provide power
cord fire protection.
Unit power
automatically
disconnects
when unsafe conditions
are detected.
by pressing

the reset

Use recommended
wire size given in Table 1 and
install
a single branch
circuit.
All wiring
must
comply with local and national codes. All units are
designed to operate offONE
single branch circuits
only.

Upon completion
of unit installation
for 208/230V
models, an operational
check should be performed
using the TEST/RESET
buttons on the plug head.

NOTE:

accessory.

Table

Use copper conductors
1--SUGGESTED

only.

BRANCH

CIRCUIT

NOTE:
The 265v models do not incorporate
this
feature as they require use of the electrical subbase

WIRE SIZES*

NAMEPLATE AMPS

AWG WIRE SIZEt

7.0 to 12

12.1 to 16

16.1 to 24

LEGEND
AWG - American Wire Gauge
* Single circuit from main box.
1- Based on copper

wire at 60°C temperature

Table

rating.

2--RECEPTACLES

AND FUSE

TYPES

- 250,265

VOLTS

RECEPTACLE

AMPS

RATED VOLTS

250

265

TIME- DELAY TYPE FUSE (or
HACR Circuit Breaker)

20*

LEGEND
HACR - Heating, Air Conditioning,
Refrigeration
* May be used for 15-amp applications if fused for 15 amps.

INSTALLATION
Proper
installation
installer.
Product
covered

is the

failure due to improper
under the Warranty.

CHASSIS

Amana,
outdoor

installation

of the
is not

units

a sleeve. In applications
it is recommended
that a

can retrofit

UNIT

Carrier,

General

For competitive

retrofit

must approve

AND/OR

OPERATION

to follow this caution
or improper operation.

may

HAZARD

result

in equipment

For retrofit applications,
foam seals on outdoor coil tube
sheets must make a seal between the coil and the grille or
loss of performance
and premature
damage to the maior
components
can result.

Electric,
Table

Trane, and Friedrich sleeves/grilles
(be sure
grille is installed on the sleeve). See Table 3

for details. Gree engineering
retrofit application.

DAMAGE

Failure
damage

INSTALLATION

Units are shipped without
where unit is a replacement,
Gree sleeve be used.
These

responsibility

any other

3--Retrofit

Manufacturer
General Electric

Wall Sleeves

Wall Sleeve Part Number
Metal Sleeve RAB71
Plastic Sleeve RAB77

applications,

be sure that the

Amana

Metal Sleeve WS900D

foam seals (factory-installed
on the tube sheets)
provide a good seal between the grille and outdoor coil

Carrier

Metal Sleeve - SLEEVE-STEEL-1PK

tube sheets. These foam seals provide a barrier
to
separate
outdoor coil leaving air from mixing with
the outdoor incoming air (known as air recirculation).

Trane

Metal Sleeve SLV149

Friedrich

T-Series Metal 11-1/2"
Deep Wall Sleeve*

Plastic Sleeve - WALL-SLEEVE-1PK

(292.1 mm)

Standard Depth Wall Sleeve
16 X 42 X 133/4-in.

(406.4

X 1067 X

349.3 mm) PXWS
FR-SLEEVE-EXT
accessory
(T-Series)
wall sleeves.

is required for retrofit into Friedrich

Minimum wall sleeve opening must be greater than
14.75 X 40.00 in. (374.7 x 1016 mm)

COIL TUBE
SHEETS

OUTDOOR
ORIFICE

WIRE SCREEN

\
DISCHARGE
GRILLE

INLET
FILTERS

ACCESSOR
OUTDOOR

GRILLE
ACCESSORY
WALL
SLEEVE

INDOOR
COIL

FRONT
PANEL

Fig. 4 - Unit Components

BASEPAN

RETROFIT

SLEEVE

PREPARATION

IMPORTANT:
Inspect
wall sleeve
thoroughly
prior
to installation.
Manufacturer
does
not
assume responsibility
for costs or damages
due to
defects in sleeve or for improper
installation.

ELECTRICAL
Failnre to %llow
or death.

SHOCK

this warning

Disconnect
all power
during installation.

HAZARD

conld resnlt

in personal

to unit to avoid possible

electrical

injury
shock
BOTTOM

GE Plastic
Sleeve = Remove
plastic sleeve. See Fig. 6.
INSTALLATION
SLEEVE

USING

bottom

seal

SEAL

from
Fig. 6 = Remove

OF A GREE

Bottom

Seal From

GE Plastic

Sleeve

WALL

A NON-GREE

GRILLE

This application
has become more common due to
pre-manufactured
windows
with built-in grilles or
renovations
where a Gree sleeve is used with an
existing non-Gree grille.
Use of a Gree wall sleeve with a non-Gree
grille
requires installation
of an Accessory
Baffle Kit (see
Fig. 7), which ensures a good seal between the unit
and exterior grille to prevent air recirculation.
Air
recirculation
is a large contributor
to performance
loss and premature
damage to major components.

CONDENSATE

REMOVAL

and desirable

Baffle

Kit

SYSTEM

Gree's series has a new condensate
(water) disposal
system. The outdoor fan prop has a built in slinger
ring which draws condensate water and sprays it on the
warm outdoor coil for evaporation.
Thus providing
better disposal of excess condensate
and improving
unit operating efficiency.
It is normal

Fig. 7 = Accessory

to have

some

water in the base pan to boost operating

SLINGER
RING

condensate
efficiency.

All heat pump units contain
a condensate
drain
valve. This temperature
activated drain valve opens
when the outdoor temperature
drops below 55 ° F
(12.8 ° C) to prevent water from freezing in the base
pan. The water drains from the unit though the wall
sleeve
and out the wall sleeve's
rear condensate
drainage holes. If the condensate
drain kit accessory
is attached
to the wall sleeve, water will drain
through the condensate
drain tube.
NOTE: This unit will not always evaporate
1{)0%
of the unit generated
condensate
and blown in
rain water,
If it is necessary
to control
1!)0% of
the condensate,
the Drain Kit (Part No,: DRAINand
a building
condensate
drain
system is recommended,

CONDENSER

SECTION

A(17678

Condensate

Removal

System

INSTALL

UNIT

INTO

WALL

SLEEVE

1. Carefully remove shipping tape from the front
panel and vent door. See Fig° 8o
2. Remove
present.

shipping screw from the vent door, if
See Fig. 9.

3. Remove front panel. See Fig. 10.
4. Lift unit level and slide unit into wall sleeve
until foam seal rests firmly against front of wall
sleeve.
5. Secure with four screws (supplied)
unit flange holes. See Fig. 11.
6. Reinstall

front panel.

through

See Fig. 12.

the
...............
, @_
Pull out at the bottom

to release

it from the tabs

(1). Then lift up (2).
PERSONAL

INJURY

Fig. 10 - Removing

HAZARD

Front

Panel

Failure to follow this warning could result in personal
injury or death.
Chassis weighs up to 150 pounds (68.0 kg). Seek help
when lifting unit.
Lift unit by holding unit basepan.

UNIT
Failure
damage

DAMAGE

HAZARD

to follow this caution
or improper operation.

may

result

Failure to remove shipping
tape and screw will prevent
fresh air vent door from opening and may result in damage
to vent door cable

Fig. 8 - Shipping

_f J

in equipment

Tape

Fig. 11 - Securing

Unit

Location

Place tabs over top rail (1). Push Inward
bottom until panel snaps into place (2).
Remove shipping
if present

• ....

J-J

Fig. 9 - Shipping

Screw

Location

Fig. 12 - Replacing

Front

Panel

SYSTEM

CONFIGURATION

VENTILATION
The ventilation
unit, behind

CONTROL
control

lever is located

at left side of

front panel.

NOTE:
The vent door shipping hardware must be
removed
before
using vent
control
lever.
See
See figure 9,
When set at CLOSE,
only the air inside
circulated and filtered.
When set at OPEN,
into room.
efficiency.

some outdoor

This

will

reduce

To adjust

AIR

air will be drawn

heating

Energy Tip: Keep the vent control
air will be filtered and circulated.

ADJUSTING

the room is
Vent
(Pull

or cooling

at CLOSE.

Control

lever through
to operate.)

label

Room
Fig. 16 - Ventilation

Control

Location

DIRECTION

air direction:

1. Remove
2. Remove

front panel. See Fig. 10.
louver screws that hold louver

place (from back side of front panel).
17.

Louver screws
insert in
See Fig.

3. Turn louver insert and rotate 180 °, See Fig. 18.
4. Replace

louver

5. Replace

screws and front panel.

insert.
Louver screws
Fig. 17 - Backside

Air discharge

upward

Air discharge

Fig. 18 - Adjusting

Louvers

outward

of Front

(Default)

Panel

DIP

SWITCHES

Auxiliary dip switch controls are located behind front
panel, through an opening below the control panel.
To access, remove front panel. See Fig. 10.
Dip switches
are accessible
without opening
control
box.
Unit must be powered
OFF
effectively
change their status.
See Table 5 - Dip Switch Functions

the
to

for functions

Switches

each dip switch position.

NOTE" aConfiguration
during
power up cycle.DIP switches

Fig. 19 - Dipswitch

are only read

Location

on Unit

Dipswitch

Freeze guard
Setpoint

Limit 2

Setpoint

Limit 1

Fan CON/CYC

for cooling

Fan CON/CYC for heating
Wall Thermostat enable
Electric heat only (for Heat Pumps)
Fig. 20 - Dip Switches

Table
No,
1
2
3
4

5*6

5--DIP

UP
Electric Heat Only
Wall Thermostat Enable
Fan Continuous

FUNCTIONS

DOWN
Heat Pump
Control Panel Enable

Run for Heating

REMARKS
For Heat Pump unit only.

Fan Continuous

UP*DOWN
63-80 °F
18-28°C

DOWN*UP
65-78 °F
19-26 °C

DOWN

Run for Cooling

DOWN
Two configurations (5*6)
combine to select set point
range.
When set point limit set,
display always shows full
range.

DOWN*DOWN
61-86 °F
16-30 °C
(full range)

Freeze Guard Disable

Electric Heating Only / Emergency
Heat Pump Units Only)

Heat (For

can be connected

CON

Allows the fan to operate in continuous
or cycle
modes while the unit is in heating or cooling mode
(continuous
or cycle):

(Continuous)

maintain

to the unit.

Dip-switches

DOWN

Allows fan to run continuously,
circulating
air even when the
temperature
setting has been satisfied.
This switch helps to

Heating.

If it is, this dipswitch
must be moved to the Wall
Thermostat
Enable
Position,
before
the wall
thermostat will begin control.
Heat and Cool Fan CON/CYC

DOWN*UP
65-78 °F
19-26 °C

Freeze Guard Enable

This setting is typically used for Emergency
Wall Thermostat
Enable
A wired wall thermostat

DEFAULT
DOWN
DOWN

Fan Cycle for Heat

Fan Cycle for Cool
UP*UP
68-75 °F
20-24 °C

SWITCH

the room

CYC

(Cycle)

This

setting

temperature

allows

compressor
or electric
the temperature
setting

Setpoint

Temperature

Provides

a restricted

Room Freeze

the

fan

closer

to the thermostat

to cycle

heater. The fan stops
is satisfied.

and

setting.

off with

a short

the

time after

Limits
range of temperature

control.

Protection

If unit senses
a room temperature
below
40°F
(4.4°C), the fan motor and electric strip heat will turn
on and warm the room to 50°F (10°C). The fan stops
a short time after the temperature
is satisfied.

KEYPAD

CONFIGURATION

Key_pad Configuration

Indoor

Allows further configuration
of system to desired
application.
Changes do not take affect until power is
cycled on the unit.

Change between showing setpoint only on the display
during heating and cooling modes "SP" or displaying
room temperature
during heating and cooling modes
"AA". "SP" mode is the default mode.

To enter

KeNpad

configuration

seconds, -within 30 seconds of the unit being powered
up. If the unit has had power for more than 30
continuous seconds, keypad configuration
cannot be
entered. When keypad configuration
mode is first
entered, it will default to Fahrenheit/Celsius
Display
Mode.

To modi[_uration
Press and release
buttons.

If "AA"
mode
is selected,
the room
temperature will be displayed during heating,
cooling and fan only modes.
--

Configuration

Press and release the Fan Speed
value will be displayed.

button.

Up or Setpoint

Down

Keypad Configuration
-will end on its own 30 seconds
after the last button press or when the MODE button
on the Keypad is pressed.
Celsius

Dis_y

Switch:

Sensor

Biasing

setpoint until 10 seconds after the last up
or down key press, Then the room
temperature will be displayed again,

for

Sometimes
known
as an anticipator,
the
air
temperature
sensor bias is used to adjust the room air
temperature
reading when in cooling mode.
(Not
normally required.) Default biasing value is zero. The
range for biasing change is -6 deg F to +6 deg F (-3
deg C to +3 deg C)
Indoor Air Temperature
Heating mode:

Sensor

If the on/off button is depressed (when
the unit is off) and the last mode was
either cooling or heating mode, the

--During
heating and cooling modes, if
either the up or down setpoint key is
depressed, the display will show the

Change between degrees Fahrenheit
and Celsius on
the display. An "F" indicates Fahrenheit
display and
'C' indicates Celsius. Default is degrees "F".
Indoor Air Temperature
Cooling mode:

temperature

setpoint will be displayed for 10 seconds
before displaying room temperature.

To exit Ke2_pad Configuration

Fahrenheit!

If the mode button has been changed to
either heating or cooling modes, setpoint
will be displayed for 10 seconds. After
the 10 seconds, the room
will again be displayed.

The stored

settings
the Setpoint

Displa_Z:

If "SP" is selected, only the setpoint will be
displayed during heating and cooling modes,
regardless of what the real temperature
is in
the room.

Cycle power to unit. Press and hold the Fan Speed
Button and the COOLER
button for 5 continuous

To scroll throu_zpad

Temperature

Biasin fg__r

Sometimes
known
as an anticipator,
the
air
temperature
sensor bias is used to adjust the room air
temperature
reading when in heating mode.
(Not
normally required.) Default biasing value is zero. The
range for biasing change is -6 deg F to +6 deg F (-3
deg C to +3 deg C)

AUXILIARY
WALL

CONTROLS

THERMOSTAT

TERMINAL

IMPORTANT:
Only trained,
should access electrical
panel
electrical
accessories.
Please
electrical
contractor,
dealer,
assistance.
Thermostat

qualified
personnel
on unit and install
contact
your local
or distributor
for

Wire Routing

Thermostat
wire is field supplied.
Recommended
wire gauge is 18 to 20 gauge solid thermostat wire.
NOTE: It is recommended
that extra wires are run to
unit in case any are damaged

Fig. 22 - Terminal

Install

Connector

Removal

and Replacement

Wiring

1. Check to be sure power to unit is disconnected.

during installation.

Thermostat
wire should always be routed around or
under, NEVER
through, the wall sleeve. The wire
should then be routed behind the front panel to the
easily accessible
terminal connector.

Thermostat

2. Pull terminal

connector

NOTE:

Terminal

connector

replaced

to simplify thermostat

to remove
can

removed

wiring.

3. Connect wires from the thermostat
on unit terminal connector.
4. Reinstall

terminal

and

to terminals

connector.

5. Ensure
that
unit
is configured
for
thermostat enable. (Dip Switch 2 - UP)

wall

6. Replace control panel label with wall thermostat
label. See Fig. 23.
7. Restore

THERMOSTAT
(UNDER

Fig. 21 - Proper

Wiring

Thermostat

SLEEVE,

Wire

WIRE ROUTING
BEHIND

Routing

FRONT

Beneath

PANEL)

Unit

To Unit

Wire wall thermostat input as defined in Fig. 25.
NOTE:
Terminal connector
can be removed
and
replaced

to simplify

power to unit.

the wiring.

NOTE:
For heat pump models, anytime there is a
second-stage
call
for
heating
from
the wall
thermostat, the unit will automatically
switch over to
electric heating.

Fig. 23 - Wall Thermostat

NOTE:

Refer

to thermostat

for details on installing
NOTE:

For thermostats

Control

Panel

installation

Label

instructions

wall thermostat.
that have only one fan speed

output (on or auto), the fan speed is determined
by
how the terminal connector is wired. If Low fan is
desired, wire the G output from the thermostat to GL
on the unit's terminal block. If Hi fan is desired, wire
the G output from the thermostat to GH on the unit's
terminal block.
NOTE: After proper installation, if your thermostat is
not working properly, refer to the Trouble Shooting
section.

TERMINAL

CONNECTIONS

The wall thermostat
panel.

terminal

block is located

behind

the front panel and is easily

accessible

on front of control

Energy

Management
(24VAC
in)

Common

©w
©¥
O

STATUS

LED

See

G,
C

TERMINAL

See

Note

BLOCK

NOTES:
/
/
mg
Energy Mana2eme
Tmminal Connections

1. Use terminal "O" for heat pump connection only.
2. Terminal "C" (common) is typically only required for digital
thermostats.

Wall Themlostat
Temfinal Connections

TERMINAL

Fig. 24 - Terminal

Connector

and

Status

LED Location

DESIGNATION

24 VAC

Electric Heat

UNIT DAMAGE HAZARD

Reversing Valve

GH
GL

High Fan
Low Fan

Failure to follow this caution may result in equipment
damage or improper operation,

MANAGEMENT

INPUT

(FRONT

Common

NOTE: Any illegal input combinations will be captured as thermostat wiring
failures and will light the STATUS LED indicator on main board
(see Intelligent Self-Checking
Control section)

Improper wiring may damage unit electronics. Common
busing is not permitted, Damage or erratic operation may
result,

ENERGY

Compressor

Fig.

DESK

- Wiring

Connections

CONTROL)

The controller can handle a switch signal from remote energy management
input, called EM signal or front desk
control. Input must be 24VAC. If system receives a 24VAC signal, it will turn unit off; otherwise, the unit runs in
normal control. This function will be disabled under Freeze Guard protection.
See Fig. 25 for terminal
connections.
INTELLIGENT

SELF-CHECKING

Your E-TAC has a computer

board

CONTROL
that continuously

checks

key components

of the unit to ensure

they are

operating properly. Under normal operation, unit status indicator (STATUS, on main PCB), light is steadily ON.
If there is a major problem, the unit will shut down and display a diagnostic failure code on the unit's display. If
it is only a minor failure and unit is correcting the fault by itself, the diagnostic code will be flashed on the status
LED that can easily be seen when the front panel is removed
in the table below
Table 6
sensor open/short

STATUS

codes are defined

STATUS LED Indicator Definitions

Indoor

Indoor coil sensor open or short

8-s%mnent display 'F2', with STATUS light flash 2 times and off 3 sec, repeat

Outdoor coil sensor open/short

8-s%mnent display 'F4', with STATUS light flash 3 times and off 3 sec, repeat

Freeze Guard protection

8-s%mnent display 'FP'

Indoor coil freeze protection

STATU light flash 5 times and off"3 see, repeat

Outdoor coil high temp protection

STATU light flash 6 times and off 3 sec, repeat

Defrost (heat pump type)

STATU light flash 7 times and off 3 sec, repeat

Indoor coil high temp protection

STATU light flash 8 times and off 3 sec, repeat

Thermostat wiring error

STATU light flash 9 times and off 3 see, repeat

High pressure protection (optional)

8-s%mnent display 'El ', (the highest display grade)

NOTE:

air temp

(see Fig. 24). Failure

8-s%m'nent display

When stares light is flashing, it will be ON for 1 seconds and OFF tbr another

'FI ', with

1 seconds.

STATUS

light flash

1 times and off 3 sec, repeat

OPERATION
IMPORTANT:
When unit is first started_ high humidity
conditions
can cause condensation
to form on
discharge
grille, Keep doors and windows
closed.
Room humidity
will decrease
and moisture
will
evaporate,

TEMP CONTROL

FAN, MODE& OPERATION
Fig. 26 - E-TAC

ABOUT THE CONTROLS

ON YOUR UNIT

NOTE: In case of a power failure, the
remember
the last programmed
settings
restart to those settings.

unit
and

will
will

1. ON and OFF MODES
ON MODE

- Places unit in ready or operation

mode.

OFF MODE - Places unit in standby mode.
NOTE:
The LED above the ON/OFF button

will be

green when unit is ON and red when the unit is OFF.
All other LEDs will be off when unit is set to OFF
mode.
NOTE:

4. FAN SPEED
Set fan operation for HI, MED, LO and AUTO speed.
AUTO FAN MODE - Adjust the indoor fan speed to
balance room comfort and quietness.
The fan speed
will increase the farther away from the selected room
temperature to quickly reach desired room temperature.
As the room temperature
approaches
the selected
temperature,
the indoor
comfort level.
5. TIMER

Prover

2. TEMP

remains

connected

to unit.

Timer

CONTROL

Temp Control is used to maintain room temperature.
Compressor
will cycle on and offto keep room at the
requested level of comfort.
COOLER
(Minimum

- Lowers temperature.
temperature
setting is 61 ° F/16 ° C)

WARMER
(Maximum

- Raises temperature.
temperature

3. OPERATING
MODE-COOL
MODE-DRY
removal.
MODE-HEAT
MODE-FAN
NOTE:

CONTROLS

setting

is 86 ° F/30 ° C)

MODE

When

the unit is ON, the Timer

turn ON and operate according
Timer

OFF:

to a quiet

MODE

function can be set. Time setting range
hours. When the selected time is reached,

is 0.5 to 24
the unit will

to system settings.

When the unit is OFK the Timer

function can be set. Time setting range
hours. When the selected time is reached,
turn OFE

OFF

is 0.5 to 24
the unit will

Timer
Setting:
Press Timer button to set timer
function. The Timer LED will turn ON and "88" will

with addition

moisture

- For heating
- For fan-only

down

be displayed. Press the up or down arrows to select the
desired time.

- For cooling
- For cooling

ON:

fan slows

operation

If unit is a heat pump, raising the heat setting

5°F (2.8°C) will cause unit to use its electric heating
elements for one cycle in order to reach the new
requested temperature quickly.
15

CARE

AND CLEANING

FRONT

PANEL

AND

CASE

Turn unit off and disconnect

AIR

power

supply.

To clean, use water and a mild detergent. DO NOT
use bleach or abrasives.
Some commercial
cleaners
may damage

the plastic

OUTDOOR
Coil

IMPORTANT:
CLEANING

UNIT

side

of unit

should

be checked

Never use a high=pressure

DAMAGE

Failure
damage

regularly. Unit will need to be removed to inspect
dirt build-up that will occur on the inside of the coil.
If clogged
with
dirt or soot, coil should
be
professionally
cleaned.
NOTE:

TURN

UNIT

OFF

BEFORE

parts.

COIL

on outdoor

FILTERS

to follow this caution
or improper operation.

Do not operate
becomes
torn
immediately.

spray on coil.

HAZARD
may

unit without
or damaged,

Operating
without filters
will allow dirt and dust

result

in equipment

filters
in ptace.
it should
be

If a filter
replaced

in place or with damaged
filters
to reach indoor coil and reduce

cooling, heating, airflow and efficiency
restriction may cause damage to unit.

of unit.

Airflow

F
Coils

ili ii iiii ili

Grille

ii/i iiiii/i iiI

Clean inside and outside of outdoor coils regularly
Dirty filterNeeds cleaning
Fig. 27 = Outdoor

Clogged filter Greatly reduces cooling,
heating and airflow.

Coil
Fig. 28 - Identifying

UNIT

DAMAGE

HAZARD

Failure
damage

to follow this caution
or improper operation.

Airflow

restriction

may

result

in equipment

BASE

to the unit.

PAN

In some installations,
dirt or other debris may be
blown into unit from outside and settle in base pan
(bottom of unit).

2 Air filters

....
Removing Air Filter

Fig. 29 - Removing

filters

clean

wilh

Decrease

Save energy.

Prevent

clogged

Reduce

risk of premature

To Clean

In some areas of the United States, a "jell=like"
substance may be seen in the base pan. Check base
pan periodically
and clean, if necessary.

Pull u

Filter

The most important thing you can do to maintain unit
efficiency is to clean the filters at least every 30 days
(or sooner depending on application).
Clogged filters
reduce cooling, heating and airflow.
Keeping

may cause damage

Clogged

cost of operation.
indoor coil.
component

Air Filters:

Vacuum

off heavy soil.

Run water through

Dry thoroughly

filters.

before replacing.

Push down

and Replacing

Air Filter
Replacin

Air Filter

failure.

PREVENTATIVE
Preventative

MAINTENANCE

maintenance

is essential

to proper

unit operation,

efficiency

and longevity.

To ensure equipment operates properly, it must be properly maintained.
Equipment operation should be checked
and verified several times during each year. During regular unit inspection
and maintenance,
follow the
guidelines below:
o

Clean both sides of outdoor coil with warm
(Never use high pressure spray on coils.)

water and a mild detergent.

o
o

Clean basepan
Clean outdoor

Clean indoor coil.

Clean indoor fan, wire screen and front panel.

Clean or install new indoor-air

Clean wall sleeve and outdoor

o
o

Inspect cord and receptacle.
Secure electrical connections.

Ensure front panel is properly

mounted

Ensure wall sleeve is installed

properly.

Ensure heat and cool cycles operate

and outdoor vent filter.
orifice and fan.
(Never

use high pressure

spray on coils.)

inlet filter(s).
grille.

and not damaged.

properly.

Do not use corrosive

coil cleaners.

TROUBLESHOOTING
POSSIBLE CAUSES
UNiT DOES NOT START
Unit may have become unplugged
Fuse may have blown
Circuit breaker may have been tripped
Unit may be off or in wall thermostat mode.
Check section on dipswitch settings to verify
dipswitches are set properly.
* Unit may be in a protection or diagnostic failure
mode. See section on Intelligent Self=checking
Control.
.
.
*
*

UNIT NOT COOLING/HEATING

SOLUTHONS

. Check that plug is plugged securely in wall receptacle.
Note :Plug has a test/reset button on it. Make sure that the plug
has not tripped.
* Replace the fuse. See Note 1.
* Reset circuit breaker. See Note 1.
, Turn unit on (bottom right button on keypad).
Note: If the unit turns on, the LED will be green. If the unit is off,
the LED will be red. If there is no LED on, there is a problem
with power or damage to the control.

ROOM

* Unit air discharge section is blocked
* Temperature setting is not high or low enough
Note: Setpoint limits may not allow the unit to heat
or cool the room to the temperature desired.
Check section on dipswitch settings.
° Unit air filters are dirty.
, Room is excessively hot or cold when unit is started.
, Vent door left open
* Unit may be in a protection or diagnostic failure
mode. Check section on Intelligent Self-checking
Control.
* Compressor is in time delay. There is a protective
time delay (approx. 3 minutes) on starting the
compressor after a power outage (or restarting
after it has been turned off), to prevent tripping of
the compressor overload.
DISPLAY HAS STRANGE
NUMBERS/CHARACTERS
ON iT

. Make sure that curtains, blinds or furniture are not restricting or
blocking unit airflow.
, Reset to a lower or higher temperature setting.
* Remove and clean filters.
, Allow sufficient amount of time for unit to heat or cool the room.
Start heating or cooling early before outdoor temperature, cooking
heat or gatherings of people make room uncomfortable.
* Close vent door.
. Check dipswitch settings for desired comfort.

UNiT MAKING NOISES

. Clicking, gurgling and whooshing
operation of unit.

WATER DRiPPiNG OUTSIDE

* If a drain kit has not been installed, condensation runoff during
very hot and humid weather is normal. See Note 2. If a drain kit has
been installed and is connected to a drain system, check gaskets
and fittings around drain for leaks and plugs.

Wait approximately

3 minutes for compressor to start

. The unit may be in a diagnostic condition. Check Intelligent Selfchecking Control section to determine if unit has had a failure.
* The unit may be set for °C (instead of °F), see the keypad
configuration section
noises are normal during

WATER DRIPPING INSIDE
. Wall sleeve is not installed level

. Wall sleeve must be installed level for proper drainage of
condensation. Check that installation is level and make any
necessary adjustments.

iCE OR FROST FORMS ON INDOOR COIL
. Low outdoor temperature
. Dirty filters

. When outdoor temperature is approximately 55 o F (12.8°C) or
below, frost may form on the indoor coil when unit is in Cooling
mode. Switch unit to FAN operation until ice or frost melts.
. Remove and clean filters.

COMPRESSOR PROTECTION
. Power may have cycled, so compressor is in a
restart protection.

. Random Compressor restart = Whenever the unit is plugged in,
or power has been restarted, a random compressor restart will
occur. After a power outage, the compressor will restart after
approximately 3 minutes.
* Compressor Protection - To prevent short cycling of the
compressor, there is a random startup delay of 3 minutes and a
minimum co m pressor run time of 3 minutes.

WALL THERMOSTAT

* Verify wiring is correct between thermostat and unit.
* Dip Switch settings are only read during power up. Unplug unit
and verify Dip Switch Settings, then plug in unit.

PROBLEM

NOTES:
1=If circuit breaker is tripped or fuse is blown more than once, contact a qualified electrician=
2= If unit is installed where condensation
drainage could drip in an undesirable location, an accessory
system=

drain kit should

be insta!led and connected

to drain

R-T

CONVERSION

R25:20.0k_
tEF ]

Rrnin.

[k£_]

TABLE

(Tolerance
Rnorn.

1%)
[k£_]

Rrna×. [k£_]

32.0

64.46

65.89

67.34

33,0

62=68

64=03

65=40

34,0

60=95

62=23

63=53

35,0

59=27

60=48

61,71

36,0

57=65

58=80

59=96

37,0

56=07

57,16

58=26

38=0

54,54

55,58

56,62

39,0

53=06

54=04

55=03

40,0

51,63

52=55

53=49

41.0

50.23

51.11

52.00

42,0

48=88

49=72

50=56

43=0

47,57

48,36

49= 16

44,0

46=30

47=05

47=81

45,0

45=07

45=78

46=50

46,0

43=87

44=55

45=23

47,0

42=71

43=35

44=00

48,0

41,58

42,19

42=81

49,0

40=48

41,07

41,65

50,0

39=42

39=98

40=53

51,0

38=39

38=92

39=45

52,0

37=39

37=89

38=39

53,0

36=42

36=89

37=37

54,0

35=47

35=93

36=39

55,0

34=56

34=99

35=43

56.0

33,66

34.08

34,50

57,0

32,80

33,20

33,59

58,0

31,96

32,34

32,72

59,0

31,14

31,51

31,87

60,0

30,35

30,70

31,05

61,0

29,58

29,91

30,25

62,0

28,83

29,15

29,47

63,0

28,10

28,41

28,72

64,0

27,40

27,69

27,99

65,0

36,71

26,99

27,28

66.0

36.04

26.31

26.59

67.0

25.39

25.66

25.92

68.0

24.76

25.01

25.27

69.0

24.15

24.39

24.64

70.0

23.55

23.79

24.03

71.0

22.97

23.20

22.43

72.0

22,40

22,63

22,85

73.0

21.85

22.07

22.29

74,0

21,32

21,53

21,74

75.0

20.80

21.01

21.21

76.0

20.30

20.50

20.70

77.0

19,80

20.00

20,19

78,0

19,33

19,52

19,71

79,0

18,86

19,05

19,23

80.0

18.41

18.59

18.77

81,0

17,97

18,15

18,32

82.0

17.54

17.71

17.89

83,0

17,12

17,29

17,46

84.0

16.71

16.88

17.05

85.0

16.32

16.48

16.65

86.0

15.93

16.10

16.26

87.0

15.56

15.72

15.88

88.0

15.19

15.35

15.51

89.0

14.84

14.99

15.15

90.0

14.49

14.65

14.80

91.0

14.15

14.31

14.46

92.0

13.82

13.98

14.13

93.0

13.50

13.66

13.81

94.0

13.19

13.34

13.49

95.0

12.89

13.04

13.19

96.0

12.59

12.74

12.89

R=TCONVERSION
TABLE
R25:20.0k_

(cont.)
(Tolerance 1%)
Rnorn. [k£_]
12=45
12,17
11 =90

tEF]
97=0
98,0
99,0

Rrnin. [k£_]
12=30
12,02
11 =75

100=0
101 =0

11 =48
11 =22

11 =63
11 =37

11 =77
11 =51

102=0
103=0

10=97
10=72

11 =11
10=87

11 =26
11 =01

104=0
105=0

10=48
10=25

10=62
10=39

10=77
10=53

106=0
107=0

10=02
9=791

10=16
9=937

10=30
10=08

108=0
109=0
110=0

9=573
9=361
9=154

9=719
9=506
9=299

9=866
9=653
9=446

111 =0
112=0

8=952
8=755

9=097
8=900

9=243
9=046

113=0
114=0
115=0

8=563
8=376
8=193

8=708
8=520
8=338

8=854
8=667
8=484

116=0
117=0

8=015
7=841

8=159
7=985

8=305
8=131

118=0
119=0

7=671
7=506

7=815
7=650

7=961
7=796

120=0
121 =0

7=344
7=186

7=488
7=330

7=634
7=476

122=0

7=033

7=176

7=322

Rrna×. [k£_]
12=60
12,32
12,04

16RD(BK)

15RD
15BU!:_ _!
12BU
C5
-_

AP3

2WH

4WH
Xl

6BK

HEATER

LEGEND
AP2

RelayC!_UiU_ard

AP3

Ois_

CI
C2

Corn #r_ssor Capacitor

U, _

Eiectric Heater Rely
Compressor Re_ay

M1
M2

Com£ressor Motor
Outdoor Fan Motor

hdoor

OU_UBE

Outdoor Coi_ Sensor

Cireu_ _ard

Pen Motor

ROOM
SAT
TC

Com2r_sor Over_o_
Transformer

TRiN-24V

Tra_former

TUBE
X!

_ndoor Coii Sensor
Main _wer Conr_Gor

Heater Connector

X3
X4

24 Volt ConP_¢lor

Heater Limi_ Coni_or
_ indoor Fan Motor Comec_or
Trar_;sformer Comeclor

X7,X8

Board Jumper Come.or

_,%1

XT2

Terminal Stock

R_ersing

Valve (Heat Pump Units)

GB Series -Typical Wiring Schematic for Standard
(Except Models with 5KW Elec. Heaters)

Units

14YE

15RD
1BK

2WH
5RD
÷_ 4RD

17BU
BK

HEATER

LEGEND
AP1

Main Circuit Board

AP2

Rei_uCircuit

AP3
C!

BisplaIy Circuit _ard
Compressor Ca_citor

Pan Motor Capacitor

Lt, _

Eiectric H_ter
C£_£ressor

_ard

Rei87

Re_ay

M1
M2

Outdoor Pan Motor

indoor Fan Motor

OU_UBE

Outdoor Co_ Sensor

ROOM
SAT

Room Air Temp. Sensor

Trar_former

TRiN,_24V

Trar_lormer 24 VoR Conreetor

TUBE

indoor Coit Sensor

Main Power Conne_or

X2
X3

Heater Oenne_or
Heater Umit Con_etor

tnd_r

Fan Motor Conneclor

Transformer Co nne_or

GB Series

-Typical

X,_,X:8

Boa_d Jum£er Connec_or

XT2

Termini

R:_e_sing _e

Wiring

Schematic

Biock
(Heat Pump Unils)

for Models

with

5KW

Elec.

Heaters

GREE GB Series
Packaged Terminal
Air Conditioner Limited Warranty
GREEWILL
NOT BE RESPONSIBLE
FOR:
1. CLEANING
REQUIRED
PRIORTOWARRANTY

TWO-YEAR PARTS AND LABOR LIMITED WARRANTY - During the first two years
after purchase, GREE will, through its authorized independent servicing dealer or service
stations*, and free of charge to the user or subsequent users, repair or replace any parts
that fail due to defect in material or workmanship. The replacement part can be a new or
remanufactured part as provided at GREE'S sole option.
EXTENDED THREE-YEAR PARTS AND LABOR LIMITED WARRANTY ON SEALED
REFRIGERATION SYSTEM ONLY - During the third through fifth years after date
of original purchase, GREE will, through its authorized servicing dealers and service
stations* and free of charge to the end user or subsequent users, repair or replace the
compressor, condenser, evaporator or connecting tubing if it failed due to defect in material
or workmanship. This includes system refrigeration charge. The replacement part can be
new or a remanufactured part at GREE'S sole option.
EXTENDED

THREE=YEAR

PARTS

ONLY

LIMITED

WARRANTY

center,

and reinstallation

charges

LIMITATION
OF WARRANTIES
- ALL
WARRANTIES
OF MERCHANTABILITY
PURPOSE)
ARE HEREBY
EACH LIMITED WARRANTY
LIMITATIONS
LIMITATION

LIMITED
IS GIVEN

necessary

IMPLIED WARRANTIES
AND FITNESS
FOR
IN DURATION
AND APPLIES.

ON HOW LONG AN IMPLIED
MAY NOT APPLY TO YOU. THE

THIS WARRANTY
ARE EXCLUSIVE
CHANGED
BY ANY DISTRIBUTOR,

to accomplish

instruction
installation.

Damage

6.
7.

NON-SEALED

8.
9.
10.
11.

repair.
(INCLUDING
PARTICULAR

IMPLIED
USE OR

TO THE PERIOD
FOR WHICH
SOME STATES DO NOT ALLOW

WARRANTY
EXPRESSED

Standard
maintenance,
cbaning
or damage
normal maintenance
as outlined in the owner's

REFRIGERATION
SYSTEM
ONLY - During the third through fifth years after date of
original purchase,
Gree will, through its authorized
servicing dealers and service stations
and free of charge to the end user or subsequent
users, repair or replace any non-seabd
system part (motor, solenoid, thermistor, circuit boards, relays, switch, capacitor, overload,
drain valve, fan, stator) if failed due to defect in material or workmanship.
The replacement
part can be new or a remanufactured
part at GREE'S
sole option. THiS LiMiTED
WARRANTY
DOES NOT iNCLUDE
LABOR, user is responsible
for labor, including cost
of diagnosis of problem, removal and transportation
of the air conditioner
to and from the
service

12.
13.

LASTS,
SO THE ABOVE
WARRANTIES
MADE IN

AND MAY NOT BE ALTERED,
ENLARGED,
DEALER, OR OTHER PERSON WHATSOEVER.

methods

or repairs

of control

needed

and use

as consequence

independent

dealers

or service

stations

This warranty

are registered
gives

with Gree through

you specific

legal

rights,

its distributor
and you

Edition

Date:

10q

of air conditioning
of faulty

installation

unit

to perform
after

initial

or application.

Shipping
damage
or damage
as a result of transporting
the unit. This is the
responsibility
of the selling dealer or the authorized service station.
ANY
SPECIAL,
iNDiRECT
OR
CONSEQUENTIAL
PROPERTY
OR
COMMERCIAL
DAMAGE OF ANY NATURE WHATSOEVER.
Some states do not
allow the exclusion
or limitation
of incidental
or consequential
damages,
so the
above limitation or exclusion may not apply to you.
Warranty coverage
of accessory
items (wall thermostats,
wall sleeves, etc.)
installations
of non-corrosion
protected models within one (1) mile of a corrosive
body of water or environment
shall void the EXTENDED
THREE-YEAR
PARTS
AND LABOR LiMiTED
WARRANTY
ON SEALED
REFRiGERATiON
SYSTEM
ONLY and EXTENDED
THREE-YEAR
PARTS ONLY LiMiTED
WARRANTY
ON
NON-SEALED
REFRiGERATiON
SYSTEM
ONLY limited warranties.

have other

failure

PARAGRAPH
- Packed terminal units (GB Series) built with corrosion
protection
are exempt from the exclusion -"Corrosive
Environment."
The unit model number
is identified on the nameplate with CP suffix.
Reimbursement
for replacement
parts or repair services which are not supplied or
designated
by GREE and which are specifically
covered under this warranty.
GREE products
installed
outside
the continental
U.S.A.
Alaska,
Hawaii, and
Canada.

organization.

may also

from

This is the responsibility
of the installer.
Failure to start due to voltage conditions,
blown fuses, open circuit breakers or any
other damages due to the inadequacy
or interruption
of electrical services.
Damage
or repairs
needed
as consequence
of any misapplication,
abuse,
unauthorized
alteration,
improper servicing
or operation.
Damage
as a result
of floods,
winds, fires, lightning,
accidents,
corrosive
environment,
or other conditions
beyond the control of GREE.
EXCEPTION
TO
CORROSIVE
ENVIRONMENT
EXCLUSION
iN ABOVE

ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED
DURING NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER
NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE
REMAINING TIME PERIOD OF THIS WARRANTY.

*Authorized

REPAIR.
resulting
manual.

rights

which

vary from

state to state.

oo
==
o

IF YOUR AIR CONDITIONER DOES NOT WORK, FOLLOW THESE STEPS IN ORDER:
31.

CHECK THE THINGS YOU CAN DO YOURSELF.
These include being sure the
air conditioner
is plugged in firmly in an appropriate
receptacle,
checking the fuse
or circuit breaker
and ensuring
its replacement
or resetting,
if necessary,
and
rereading the instruction
book to ensure that alI controls are set properly. By doing
this you can save money. Many unnecessary
service calls result in the serviceman
doing what the owner can do for him or herself.

CONTACT

DEALER

THE

AUTHORIZED

SERVICE

CENTER

RECOMMENDS.
They have been set up to handle the great majority of alI possible
service problems. The quickest,
surest and best way to get your air conditioner
back in service is to use this step before proceeding
further.

Q,.
_a

YOUR

&
3

Q,.

o
C_

9
O')
O3
DO
LO
0
CO
CO

,,q
0

9
Edition

Date:

01-12

CONTACT THE DISTRIBUTOR SERVING YOUR AREA. Your dealer can give you
his name or you can consult your yellow pages.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Fri Mar 30 04:14:43 2012
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Gree ETAC 07HC230V20A A User Manual PACKAGE UNIT Manuals And Guides 1203305L

Navigation menu

Versions of this User Manual:

Views

Navigation