Greenheck Fan 474051 Users Manual

474051 to the manual 5d2489e4-d1d5-4d37-927c-2cd170f2566b

2015-02-09

: Greenheck-Fan Greenheck-Fan-474051-Users-Manual-562441 greenheck-fan-474051-users-manual-562441 greenheck-fan pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

Part #474051
Fiberglass Centrifugal Fan

Installation, Operation and Maintenance Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the
product described. Protect yourself and others by observing all safety information. Failure to comply with instructions
could result in personal injury and/or property damage! Retain instructions for future reference.

Model BCSW-FRP

General Safety Information
Only qualified personnel should install this fan. Personnel
should have a clear understanding of these instructions
and should be aware of general safety precautions.
Improper installation can result in electric shock, possible
injury due to coming in contact with moving parts, as well
as other potential hazards. Other considerations may
be required if high winds or seismic activity are present.
If more information is needed, contact a licensed
professional engineer before moving forward.
DANGER
Always disconnect power before working on or near
a fan. Lock and tag the disconnect switch or breaker
to prevent accidental power up.
CAUTION
When servicing the fan, motor may be hot enough
to cause pain or injury. Allow motor to cool before
servicing.
CAUTION
Precaution should be taken in explosive
atmospheres.

1. Follow all local electrical and safety codes, as well
as the National Electrical Code (NEC), the National
Fire Protection Agency (NFPA), where applicable.
Follow the Canadian Electric Code (CEC) in
Canada.
2. The rotation of the wheel is critical. It must be free
to rotate without striking or rubbing any stationary
objects.
3. Motor must be securely and adequately grounded.
4. Do not spin fan wheel faster than max cataloged
fan rpm. Adjustments to fan speed significantly
effects motor load. If the fan RPM is changed, the
motor current should be checked to make sure it is
not exceeding the motor nameplate amps.
5. Do not allow the power cable to kink or come in
contact with oil, grease, hot surfaces or chemicals.
Replace cord immediately if damaged.
6. Verify that the power source is compatible with the
equipment.
7. Never open access doors to a duct while the fan is
running.

Fiberglass Centrifugal Fan

Receiving
Upon receiving the product check to make sure all
items are accounted for by referencing the bill of
lading to ensure all items were received. Inspect each
crate for shipping damage before accepting delivery.
Notify the carrier if any damage is noticed. The
carrier will make notification on the delivery receipt
acknowledging any damage to the product. Impact
damage will appear as whitening of the surface or
star-shaped cracks or crazes. If this damage is limited
to the exterior surface of the fan, it may be superficial.
The fan should not be installed until fully repaired
by an authorized repairman. All damage should be
noted on all the copies of the bill of lading which
is countersigned by the delivering carrier. A Carrier
Inspection Report should be filled out by the carrier
upon arrival and the Traffic Department. If damaged
upon arrival, file claim with carrier. Any physical
damage to the unit after acceptance is not the
responsibility of Greenheck Fan Corporation.

Unpacking
Verify that all required parts and the correct quantity
of each item have been received. If any items are
missing, report shortages to your local representative
to arrange for obtaining missing parts. Sometimes it
is not possible that all items for the unit be shipped
together due to availability of transportation and truck
space. Confirmation of shipment(s) must be limited to
only items on the bill of lading.

Handling
The fan should not be removed from its shipping crate
before being moved to its final location. Lifting straps
should only be attached to the structural steel base,
or clevis pins can be used if the fan skid has “lifting
holes” in all four corners.
If lifting lugs are provided on the fan housing, only
use to lift the housing and not the entire fan. Handle
in such a manner to avoid scratching or chipping.
Special care must be taken to avoid causing damage
from stress or shock. Damaged finish may reduce
ability of the fan to resist corrosion.
Fans should never be lifted by the shaft, fan housing,
motor, belt guard, windband or accessories.

Storage
• Rotate fan wheel monthly and purge bearings once
every three months
• Energize fan motor once every three months
• Store belts flat to keep them from warping & stretching
• Store unit in location which does not have vibration
• After storage period, purge grease before putting fan
into service
If storage of fan is in a humid, dusty or corrosive
atmosphere, rotate the fan and purge the bearings
once a month. Improper storage which results in
damage to the fan will void the warranty.
2

Model BCSW-FRP

Fans are protected against damage during shipment. If
the unit cannot be installed and operated immediately,
precautions need to be taken to prevent deterioration
of the unit during storage. The user assumes
responsibility of the fan and accessories while in
storage. The manufacturer will not be responsible
for damage during storage. These suggestions are
provided solely as a convenience to the user.

INDOOR
The ideal environment for the storage of fans and
accessories is indoors, above grade, in a low humidity
atmosphere which is sealed to prevent the entry of
blowing dust, rain, or snow. Temperatures should be
evenly maintained between 30°F (-1°C) and 110°F (43°C)
(wide temperature swings may cause condensation
and “sweating” of metal parts). All accessories must be
stored indoors in a clean, dry atmosphere.
Remove any accumulations of dirt, water, ice or snow
and wipe dry before moving to indoor storage. To avoid
“sweating” of metal parts allow cold parts to reach
room temperature. To dry parts and packages use a
portable electric heater to get rid of any moisture build
up. Leave coverings loose to permit air circulation and
to allow for periodic inspection.
The unit should be stored at least 3½ in. (89 mm) off the
floor on wooden blocks covered with moisture proof
paper or polyethylene sheathing. Aisles between parts
and along all walls should be provided to permit air
circulation and space for inspection.

OUTDOOR
Roads or aisles for portable cranes and hauling
equipment are needed.
The fan should be placed on a level surface to prevent
water from leaking into the fan. The fan should be
elevated on an adequate number of wooden blocks so
that it is above water and snow levels and has enough
blocking to prevent it from settling into soft ground.
Locate parts far enough apart to permit air circulation,
sunlight, and space for periodic inspection. To minimize
water accumulation, place all fan parts on blocking
supports so that rain water will run off.
Do not cover parts with plastic film or tarps as these
cause condensation of moisture from the air passing
through heating and cooling cycles.
Fan wheels should be blocked to prevent spinning
caused by strong winds.

Inspection & Maintenance during Storage
While in storage, inspect fans once per month. Keep a
record of inspection and maintenance performed.
If moisture or dirt accumulations are found on parts,
the source should be located and eliminated. At each
inspection, rotate the wheel by hand ten to fifteen
revolutions to distribute lubricant on motor. If paint
deterioration begins, consideration should be given to
touch-up or repainting. Fans with special coatings may
require special techniques for touch-up or repair.

Machined parts coated with rust preventive should be
restored to good condition promptly if signs of rust occur.
Immediately remove the original rust preventive coating
with petroleum solvent and clean with lint-free cloths.
Polish any remaining rust from surface with crocus cloth
or fine emery paper and oil. Do not destroy the continuity
of the surfaces. Wipe clean thoroughly with Tectyl® 506
(Ashland Inc.) or the equivalent. For hard to reach internal
surfaces or for occasional use, consider using Tectyl®
511M Rust Preventive or WD-40® or the equivalent.

Table of Contents

General Information
Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Recommendations
BCSW-FRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Belt Guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Drain Connections . . . . . . . . . . . . . . . . . . . . . . . . . 5
Ductwork / Stacks . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rotatable Housing . . . . . . . . . . . . . . . . . . . . . . . . . 5
Radial gap, overlap & wheel alignment . . . . . . . . . 6
Flexible Couplings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
V-Belt Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unit Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . 9-10
Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shaft Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
V-Belt Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unit Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance Log . . . . . . . . . . . . . . . . . . . . Backcover
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . Backcover

CAUTION
When installing a fan, ensure the proper protective
devices are used to protect personnel from
moving parts and other hazards. A complete
line of protective accessories are available from
Greenheck including belt guards, shaft guards, and
electrical disconnects.

Electrical Disconnects
All fan motors should have disconnects located in
close visual proximity to turn off electrical service.
Service disconnects shall be locked out when
maintenance is being performed.

Moving Parts
All moving parts must have guards to protect
personnel. Refer to local codes for requirements
as to the number, type and design. Fully secure fan
wheel before performing any maintenance. The fan
wheel may start “free wheeling” even if all electrical
power has been disconnected. Before the initial
start-up or any restart, check the belt and shaft
guards and the access doors to ensure that they
are installed and secure.

Model BCSW-FRP

Installation

Rot

One fan
diameter

ion

POOR
GOOD

GOOD

Ducted Outlet Installations
Discharge Duct Turns - Duct turns located near the
fan discharge should always be in the direction of the
fan rotation.
tion

a
Fan performance is reduced when duct
turns are made immediately off the
fan discharge. To achieve cataloged
fan performance there
should be at least
three equivalentSYSTEM EFFECT
ion FACTORS CURVES
at
duct1.2
diameters of
straight ductwork
1.0
between
the fan
discharge and
POOR
any 0.8
duct turns.

Length of Straight Duct

GOOD

Ducted Inlet Installations
Inlet Duct Turns - Installation of a duct turn or elbow
too close to the fan inlet
reduces fan performance
because air is loaded
Three fan wheel diameters
unevenly into the fan
wheel. To achieve full fan
performance, there should
be at least three fan wheel
diameter between the turn
POOR
or elbow and the fan inlet.

0.6

ion

E
RV

2
E
RV
U
C
E3
RV
CU
SYSTEM
EFFECT
VE 4
CUR

0.4

1.2

0.2

GOOD

3/4 to one
fan
wheel
diameter

0.0

3/4 to one
fan

FACTORS C

STATIC PRESSURE LOSS

1.0

wheel
25
30 diameter
35
40
0.8
Non-Ducted Installations
FPM X 100
Inlet Clearance - Installation
ofVELOCITY
a fan with an open
OUTLET
0.6 will cause
inlet too close to a wall or bulkhead

Three fan wheel diameters

One fan
diameter

Length of Straight Duct

Rot

One fan
wheel
diameter

STATIC PRESSURE LOSS

Rot

Installations with inlet or discharge configurations
that deviate from this standard may result in reduced
fan performance. Restricted or unstable flow at the
fan inlet can cause pre-rotation of incoming air or
uneven loading of the fan wheel yielding large system
losses and increased sound levels. Free discharge
or turbulent flow in the discharge ductwork will also
result in system effect losses. Refer to the following
diagrams for the most efficient installation conditions.

Rot

3/4 to
one fan
wheel
diameter

One fan
3/4 to
wheel
one fan
diameter
wheel
diameter

reduced fan performance. It is desirable to have
0.4parallel fan units
one fan wheel diameter between
and a minimum of three-fourths of a wheel diameter
0.2
between the fan inlet and the wall.
3/4 to
one fan
wheel
diameter

1.2

Three fan wheel diameters

Turning
Vanes

Rota

Rota
n

tio

POOR
POOR

One fan
wheel
diameter

1.0
STATIC PRESSURE LOSS

Inlet Spin - Inlet spin is a frequent cause of reduced
fan performance. The change in fan performance is a
function of the intensity of spin and not easily defined.
The best solution is proper duct design and airflow
patterns. Turning vanes reduce the effects of inlet spin.

3/4 to

One fanFACTORS
one fan
SYSTEM EFFECT
CURVES
0.0
diameter
wheel
0
5 diameter
10

One fan
wheel
diameter

FPM X 100
OUTLET VELOCITY

0.8
E
RV

Single Fan Installation

0.6

0.4
3/4 to

0.2one fan

One fan
wheel
diameter

wheel
diameter

0.0

GOOD

One fan
diameter

2
E
RV
CU
E3
RV
CU
E4
URV
3/4Cto

FPM X 100

ion

Rot

Free Discharge - Free or abrupt discharge into a
plenum results in a reduction in fan performance. The
effect of discharge static regain is not realized.

One fan
wheel
diameter

1.2
1.0

POOR

1 Fan
Wheel
Diameter

0.8
0.6

Rot

Model BCSW-FRP

SSURE LOSS

ion

Rot

one fan
wheel
diameter

ParallelOUTLET
Fan Installation
VELOCITY

Rot

POOR

GOOD

Rot

Turning
Vanes

Bases (Foundation and Isolation)

Drain Connection

In order to assure continued alignment, a high
strength, non-shrink epoxy grout is recommended
to provide the desired mechanical properties for
support of the fan. This type of support ensures the
appropriate transmission of static and dynamic loads
to the equipment foundation.

Make sure to either connect the drain or keep it
plugged. Never leave the drain open to drain freely.
The drain line must be installed using either a U-trap
arrangement or an equivalent method (drain leg is
submerged in liquid). To obtain a proper seal, the leg
length must be greater than the system pressure drop.

To eliminate vibration and noise from being transferred
to the building, vibration isolators should be used.
The fan is mounted directly on the base and must be
supported for the entire length of the fan base angle.
Isolators are installed between the base and the
foundation.

Ductwork / Stacks

After the fan and isolators are installed, the entire
assembly must be leveled. Position the level on
the base, not the fan shaft, for proper leveling.
Additionally, the motor and fan shafts must be
level and parallel relative to each other for proper
alignment.

Belt Guards
If the belt guard is not factory mounted, then it must
be field mounted. Brackets and mounting hardware
are the responsibility of the installer. Mounting
bracket locations vary with motor mounting position,
arrangement, and fan type. The bearing supports and
fan structure are used in most instances and when
the motor is not mounted to the fan itself, a bracket
should also be located near it. This information is
intended as only a guide and actual field conditions
may dictate another mounting location for the guard
brackets. Refer to local codes for securing guarding.

All ductwork and/or stacks must be self-supporting
and independent of the fan. The fan inlet and outlet
are not designed to support the connecting duct or
stack. The use of flexible connectors is recommended
to limit the transmission of stress to the fan. Excessive
pressure applied when bolting a flange connection
may cause damage to the fan housing or flange.

Rotatable Housings
It may be necessary to rotate the scroll of the fan
to achieve a different discharge position than what
was originally supplied. Fiberglass fan model BCSWFRP (sizes 6-25; arr. 4 and 10, Class I, II, III, and
IV) has the flexibility to be rotated in the field. This
is accomplished by removing the housing bolts,
rotating the housing to a new discharge position and
reinstalling the bolts.

Model BCSW-FRP

Radial Gap, Overlap and Wheel Alignment
Efficient fan performance can be maintained by having the correct radial gap, overlap and wheel alignment.
These items should be checked after the fan has been in operation for 24 hours and before start-up after the
unit has been serviced.
Inlet Cone

Impeller Wheel

Overlap

Impeller Wheel

Inlet Cone

Radial
Gap
Wheel

Radial
Gap
Overlap

BCSW-FRP
Sizes 6 thru 10

Unit
Size

BCSW-FRP
Sizes 15 thru 73

A Dimension

Radial Gap

± Tolerance
(in.)

± Tolerance
(mm)

± Tolerance
(in.)

± 1/8

±3

± 1/8

102

±3

± 1/8

127

±3

57⁄16

± 1/8

138

±3

7 ⁄8

± 1/8

181

7 ⁄16

± 1/8

9 ⁄8

±1

⁄8

± 1/16

±2

⁄8

± 1/32

±1

⁄16

± 1/16

±2

⁄8

± 1/32

±1

⁄16

± 1/16

±2

⁄8

± 1/32

±1

⁄4

± 1/16

±2

±3

⁄8

± 1/32

±1

1 ⁄8

± 1/16

±2

202

±5

⁄16

± 1/32

±1

1 ⁄4

± 1/16

±2

± 1/8

232

±6

⁄16

± 1/32

±1

⁄8

± 1/16

±2

⁄16

± 1/32

±1

± 1/16

±2

⁄16

± 1/16

±2

11⁄4

± 1/16

±2

⁄16

± 1/16

±2

1 ⁄4

± 1/16

±2

⁄16

± 1/16

±2

1 ⁄2

± 1/16

±2

⁄16

± 1/16

±2

1 ⁄16

± 1/16

±2

⁄32

± 1/16

±2

⁄4

± 1/16

±2

⁄4

± 1/16

±2

11⁄4

± 1/16

±2

11 ⁄8

± 1/8

283

± 10

131⁄4

± 1/8

337

± 10

15 ⁄2

± 1/8

394

± 10

17 ⁄8

± 1/8

435

± 13

19 ⁄16

± 1/8

487

± 13

± 1/8

533

± 13

253⁄4

± 1/8

654

± 13

Radial Gap is adjusted by loosening the housing bolts
and centering the inlet cone on the wheel. If additional
adjustment is required to maintain a constant radial
gap, loosening the bearing bolts and centering the
wheel is acceptable as a secondary option.

± Tolerance
(mm)

± Tolerance
(in.)

± 1/32

Overlap (maximum)

± Tolerance
(mm)

⁄8

Inlet Cone

Model BCSW-FRP

Overlap is adjusted by loosening the wheel hub from
the shaft and moving the wheel to the desired position
along the shaft. The transition between the inlet cone
and wheel should be as shown; there is a smooth feel
to the profile when moving from one component to the
other.

Flexible Couplings (Arr. 8 Only)

V-Belt Drives

Check for misalignment between the coupling halves.
Parallel and angular misalignment and separation gap
are illustrated below. Refer to coupling manufacturer’s
installation instructions for allowable misalignment
and separation gap tolerances. When correcting for
misalignment using shims, the shims should only be
located under the motor. Do not place shims under the
shaft bearings.

The V-belt drive components, when supplied by
Greenheck Fan Corporation, have been carefully
selected for this unit’s specific operating condition.

After aligning procedure, check for tightness of all
coupling component pieces and ensure that they are
clean from dirt and debris.

CAUTION
Changing V-belt drive components could result in
unsafe operating conditions which may cause
personal injury or failure of the following
components:
1. Fan shaft
2. Fan wheel
3. Bearings
4. V-belt
5. Motor
V-Belt Drive Installation

Parallel Misalignment

1. Remove the protective coating from the end of the
fan shaft and assure that it is free of nicks and burrs.
2. Check fan and motor shafts for parallel and angular
MOTOR
alignment.
FAN
FAN
3. Slide sheaves on shafts - do not drive sheaves on as
this may result in bearing damage.
4. Align fan and motor sheaves with a straight-edge or
string, and tighten.

Angular Misalignment

Separation Gap

5. Place belts over
sheaves. Do not pry or
force belts, as this could
result in damage to the
cords in the belts.
6. Adjust the tension until
the belts appear snug.
Run the unit for a few
minutes (see section
on unit start-up) and
allow the belts to seat
properly.

Aligning sheaves with
a straight-edge

7. With the fan off, adjust the belt tension by moving
the motor base. (See belt tensioning procedures in
the maintenance section of this manual). When in
operation, the tight side of the belts should be in a
straight line from sheave to sheave with a slight bow
on the slack side.

Improper sheave
alignment

Proper sheave
alignment

Model BCSW-FRP

MOTOR

Unit Start-Up

Vibration

1. Disconnect and lock-out all power switches to fan.
See warning below.

Excessive vibration is the most frequent problem
experienced during initial start-up.

2. Check all fasteners, set screws and locking collars on
the fan, bearings, drive, motor base and accessories
for tightness.
3. Rotate the fan wheel by hand and assure no parts
are rubbing.
4. Check for bearing alignment and lubrication.
5. Check for coupling alignment (Arr. 8 only).
6. Check the V-belt drive for proper alignment and tension.
7. Check all the guarding (if supplied) for being securely
attached and not interfering with rotating parts.
8. Check all electrical connections for proper
attachment.
9. Check housing and ductwork, if accessible, for
obstructions and foreign material that may damage
the fan wheel.
10. Check that the drain is connected, or plugged, and
the housing is being properly drained.
WARNING
Disconnect and secure to the “Off” position all
electrical power to the fan prior to inspection
or servicing. Failure to comply with this safety
precaution could result in serious injury or death.

Additional Steps for Initial Start-Up
1. Check for proper wheel
rotation by momentarily
energizing the fan. Rotation
is always determined by
viewing the wheel from
the drive side and should
correspond to the rotation
decal affixed to the unit.
One of the most frequently
Clockwise Rotation
encountered problems with
Always viewed from
Centrifugal Fans is motors
the drive side.
which are wired to run in the
wrong direction. This is especially true with 3-phase
installations where the motor will run in either
direction, depending on how it has been wired. To
reverse rotation of a 3-phase motor, interchange any
two of the three electrical leads.
2. Check for unusual noise, vibration or overheating of
bearings. Refer to the “Troubleshooting” section of
this manual if a problem develops.
3. Grease may be forced out of the bearing seals
during initial start-up. This is a normal self-purging
feature of this type of bearing.

Model BCSW-FRP

Common Sources of Vibration
1. Wheel Unbalance
2. Drive Pulley Misalignment
3. Incorrect Belt Tension
4. Bearing / Coupling Misalignment
5. Mechanical Looseness
6. Faulty Belts
7. Drive Component Unbalance
8. Poor Inlet/Outlet Conditions
9. Foundation Stiffness

Left unchecked, excessive vibration can cause a
multitude of problems, including structural and/or
component failure.
Many of these conditions can be discovered by careful
observation. Refer to the troubleshooting section
of this manual for corrective actions. If observation
cannot locate the source of vibration, a qualified
technician using vibration analysis equipment should
be consulted. If the problem is wheel unbalance,
the wheel should be sent back to the factory to be
properly rebalanced.
Greenheck performs a vibration test on all centrifugal
fans before shipping. Three vibration readings are
taken on each bearing in the horizontal, vertical, and
axial directions. The allowable maximum vibration
for belt drive units is 0.078 in/sec. peak (0.05 in/
sec. direct drive) velocity filter-in at the fan RPM per
AMCA Standard 204. These vibration signatures are a
permanent record of how the fan left the factory and
are available upon request.
Generally, fan vibration and noise is transmitted
to other parts of the building by the ductwork. To
eliminate this undesirable effect, the use of heavy
canvas connectors is recommended. If fireproof
material is required, FlexweaveTM 1000 - Type FN-30
can be used.

Routine Maintenance

Shaft Bearings

Once the unit has been put into operation, a routine
maintenance schedule should be set up to accomplish
the following:

The bearings for Greenheck fans are carefully
selected to match the maximum load and operating
conditions of the specific class, arrangement, and
fan size. The instructions provided in this manual
and those provided by the bearing manufacturer, will
minimize any bearing problems. Bearings are the
most critical moving part of the fan, therefore special
care is required when mounting them on the unit and
maintaining them.

1. Lubrication of bearings and motor (see below).
2. Wheel, housing, bolts and set screws on the entire
fan should be checked for tightness.
3. Any dirt accumulation on the wheel or in the
housing should be removed to prevent unbalance
and possible damage.
4. Springs should be checked for breaks and
fatigue. Rubber isolators should be checked for
deterioration.
5. Inspect fan impeller and housing looking for fatigue,
corrosion, or wear.
When performing any service to the fan, disconnect
the electrical supply and secure fan impeller.

Motors
Motor maintenance is generally limited to cleaning
and lubrication. Cleaning should be limited to exterior
surfaces only. Removing dust and grease build up on
the motor housing assists proper motor cooling. Never
wash-down motor with high pressure spray. Greasing
of motors is only intended when fittings are provided.
Many fractional motors are permanently lubricated for
life and require no further lubrication. Motors supplied
with grease fittings should be greased in accordance
with the manufacturer’s recommendations. When
motor ambient temperature does not exceed 104°F
(40°C), the grease should be replaced after 2000 hours
of running time.
CAUTION
When operating conditions of the fan are to be
changed (speed, pressure, temperature, etc.),
consult Greenheck to determine if the unit can
operate safely at the new conditions.

Refer to the following chart and the manufacturers
instructions for grease types and intervals for various
operating conditions. Never mix greases made with
different bases. This will cause a breakdown of the
grease and possible failure of the bearing.
Recommended Fan Bearing Lubrication Schedule - Standard Grease
Lubrication Schedule in Months*
Bearing Bore (inches)
Fan RPM

⁄2 1

1 ⁄8 11⁄2
1

1 ⁄8 - 115⁄16 17⁄8
23⁄16
5

27⁄16
-3

33⁄16 - 315⁄16 - 415⁄16 31⁄2
41⁄2
57⁄8

To 250

500

750

1000

1
0.5

1250

1500

0.5
0.25

2000

0.5

2500

0.5

0.25

3000

0.5

3500

0.5

0.25

4000

0.5

5000

0.25

# of shots**

*Suggested initial greasing interval is based on 12 hour per
day operation and 160ºF maximum housing temperature.
For continuous (24 hour) operation, decrease greasing
interval by 50%.
• If possible, relubricate with grease while in operation
without endangering personnel.
• For ball bearings (operating) relubricate until clean
grease is seen purging at the seals. Be careful not to
unseat the seal by over lubricating.
• For ball bearings (idle) add 1-2 shots of grease up to
2 in. bore sizes, and 4-5 shots of grease above 2 in. bore
sizes with hand grease gun.
• For roller bearings, relubricate with 4 shots of grease up
to 2 in. bore size, 8 shots for 2-5 in. bore size, and 16
shots above 5 in. bore size with hand grease gun.
• Adjust lubrication frequency based on condition of
purged grease.
• A high quality lithium base grease conforming to NLGI
Grade 2 consistency is recommended.
• The use of synthetic lubricants will increase lubrication
intervals by approximately three (3) times.

WARNING
Lubricate bearings prior to periods of extended
shutdowns or storage and rotate shaft monthly to
aid in preventing corrosion. If the fan is stored more
than three months, the bearings should be purged
with new grease prior to start-up.
Model BCSW-FRP

V-Belt Drives

Unit Identification

V-belt drives must be checked on a regular basis
for wear, tension, alignment and dirt accumulation.
Premature or frequent belt failures can be caused by
improper belt tension—either too loose or too tight—
or misaligned sheaves. Abnormally high belt tension
or drive misalignment will cause excessive bearing
loads and may result in failure of the fan and/or motor
bearings. Conversely, loose belts will cause squealing
on start-up, excessive belt flutter, slippage, and
overheated sheaves. Either excessively loose or tight
belts may cause fan vibration.

This tag is an example of an identification label on the
fan. The information provides general details about the
fan, as well as containing specific information unique to
the unit. When contacting your Greenheck representative
with future needs or questions, please have the
information on this label available.

When replacing V-belts on multiple groove drives all
belts should be changed to provide uniform drive
loading. Do not pry belts on or off the sheave. Loosen
belt tension until belts can be removed by simply
lifting the belts off the
Belt Span
Deflection =
64
sheaves. After replacing
belts, insure that slack in
each belt is on the same
side of the drive. Belt
dressing should never
Belt Span
be used.
Do not install new belts on worn sheaves. If the
sheaves have grooves worn in them, they must be
replaced before new belts are installed.

MODEL
S/N
MARK
MAX FRPM @ 70˚ F

Model = General description of fan
S/N = Serial Number assigned by Greenheck,
which is a unique identifier for every unit
Mark = Customer supplied identification
Tags are mounted on the drive frame in an area which
is clearly visible, usually near the fan outlet on the drive
side of the fan. The exact tag location may differ due fan
model and size.

The proper tension for operating a V-belt drive is the
lowest tension at which the belts will not slip at peak
load conditions. Check belt tension before start up
and after the first 24 hours of operation. The belt
tension should also be checked periodically thereafter.

Parts List
Outlet Flange
Inlet Cone

Housing
Wheel
Gasket
Backplate

Shaft Guard

Shaft Seal
Bearings
Shaft

Access Door
with Gasket

Shaft
Pulley

Belt
Guard

Motor
Pulley
Base/Housing
Foot Angle (4)
Belt
Adjustable Motor
Slide Base

10 Model BCSW-FRP

Belt Guard
Cover

Troubleshooting
Problem

Cause
Wheel rubbing (inlet)
V-belt drive

Excessive Noise
Bearings
Wheel unbalance
Low CFM
High CFM
Static Pressure
Wrong

High Horsepower

Overheated Shaft
Bearing

Check wheel for correct rotation. Increase fan speed.*

Duct system

See page 3.

Fan

Decrease fan speed.

Duct system

Resize ductwork. Access door, filters, grilles not installed.

Duct system
has more or less
restriction than
anticipated

Change obstructions in system. Use correction factor to adjust
for temperature/altitude. Resize ductwork. Change fan speed.*

Fan

Check rotation of wheel. Reduce fan speed.

Duct system

Resize ductwork. Check proper operation of face and bypass
dampers. Check filters and access doors.
Check fuses/circuit breakers. Check for switches turned off or
disconnected. Check for correct supply voltage.

Drive

Check for broken belts. Tighten loose pulleys.

Motor

Assure motor is correct horsepower and not tripping overload
protector.

Lubrication

Check for excessive or insufficient grease in the bearings.

Mechanical
Belts

Excessive
Vibration

Adjust wheel.
Tighten wheel hub or bearing collars on shaft.
Tighten Sheaves on motor/fan shaft. Adjust belt tension. Align
sheaves properly (see V-Belt Drives section). Replace worn belts
or sheaves.
Replace defective bearing(s). Lubricate bearings.
Tighten collars and fasteners.
Clean all dirt off wheel. Check wheel balance, rebalance if
necessary.

Fan

Electrical supply
Fan Doesn’t Operate

Corrective Action

Replace damaged bearing. Relieve excessive belt tension. Align
bearings. Check for bent shaft.
Adjust tightness of belts. Replacement belts should be a matched
set.

System unbalance

Check alignment of shaft, motor and pulleys. Check wheel
balance, rebalance if necessary.

Coupling
misalignment

Check alignment between coupling, motor and fan shafts.
Any adjustments should be made per coupling manufacturer’s
instructions. Shim only under motor.

* Always check motor amps and compare to nameplate rating. Excessive fan speed may overload the motor and result in
motor failure. Do not exceed the maximum cataloged RPM of the fan.
NOTE: Always provide the unit model and serial numbers when requesting parts or service information.

Model BCSW-FRP 11

Maintenance Log
Date___________________ Time______________ AM/PM
Notes:___________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________

Date___________________ Time______________ AM/PM
Notes:___________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________

Warranty
Greenheck warrants this equipment to be free from defects in material and workmanship for a period of one year from
the shipment date. Any units or parts which prove defective during the warranty period will be replaced at our option
when returned to our factory, transportation prepaid. Motors are warranted by the motor manufacturer for a period of one
year. Should motors furnished by Greenheck prove defective during this period, they should be returned to the nearest
authorized motor service station. Greenheck will not be responsible for any removal or installation costs.
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications without
notice.
Greenheck Catalog Fiberglass Centrifugal Fans, Model
BCSW-FRP, provides additional information describing the
equipment, fan performance, available accessories, and
specification data.

AMCA Publication 410-96, Safety Practices for Users and
Installers of Industrial and Commercial Fans, provides
additional safety information. This publication can be
obtained from AMCA International, Inc. at: www.amca.org.

Phone: (715) 359-6171 • Fax: (715) 355-2399 • E-mail: gfcinfo@greenheck.com • Website: www.greenheck.com

12 474051 • BCSW-FRP, Rev. 1, November 2010

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00
Instance ID                     : uuid:e1df1cb5-1668-4dc3-9162-3465a29ccf1c
Document ID                     : xmp.did:E8EC217923ECDF1197BEABDEBDFA9DB2
Original Document ID            : adobe:docid:indd:8c5835a2-ebb4-11dc-885a-ac26e191d231
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:297E545723ECDF1197BEABDEBDFA9DB2
Derived From Document ID        : xmp.did:8C3EF219D573DF11B059E781493085D4
Derived From Original Document ID: adobe:docid:indd:8c5835a2-ebb4-11dc-885a-ac26e191d231
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:137DCD12BC85DE11B2B5DE7DCD04482D, xmp.iid:147DCD12BC85DE11B2B5DE7DCD04482D, xmp.iid:4D6768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:4E6768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:4F6768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:506768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:516768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:526768B8BD85DE11AFA7CD4FD8BD1E53, xmp.iid:61D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:65D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:66D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:67D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:68D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:69D9AC98C085DE1182AFAFC0BAF32878, xmp.iid:8D3BD87BF185DE1182AFAFC0BAF32878, xmp.iid:805520404687DE11B8B4C96F0B17C99F, xmp.iid:815520404687DE11B8B4C96F0B17C99F, xmp.iid:825520404687DE11B8B4C96F0B17C99F, xmp.iid:835520404687DE11B8B4C96F0B17C99F, xmp.iid:845520404687DE11B8B4C96F0B17C99F, xmp.iid:855520404687DE11B8B4C96F0B17C99F, xmp.iid:865520404687DE11B8B4C96F0B17C99F, xmp.iid:875520404687DE11B8B4C96F0B17C99F, xmp.iid:885520404687DE11B8B4C96F0B17C99F, xmp.iid:895520404687DE11B8B4C96F0B17C99F, xmp.iid:89EE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8AEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8BEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8CEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8DEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8EEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:8FEE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:90EE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:91EE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:92EE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:93EE52BA5A87DE11B8B4C96F0B17C99F, xmp.iid:795F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7A5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7B5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7C5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7D5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7E5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:7F5F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:805F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:815F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:825F84F96F87DE11B8B4C96F0B17C99F, xmp.iid:3C470F158487DE11BCD48AC48E399EE8, xmp.iid:4C9978AC0588DE11B795EE405B658D13, xmp.iid:4D9978AC0588DE11B795EE405B658D13, xmp.iid:4E9978AC0588DE11B795EE405B658D13, xmp.iid:4F9978AC0588DE11B795EE405B658D13, xmp.iid:509978AC0588DE11B795EE405B658D13, xmp.iid:519978AC0588DE11B795EE405B658D13, xmp.iid:529978AC0588DE11B795EE405B658D13, xmp.iid:598E06000A88DE11B795EE405B658D13, xmp.iid:5A8E06000A88DE11B795EE405B658D13, xmp.iid:5B8E06000A88DE11B795EE405B658D13, xmp.iid:5C8E06000A88DE11B795EE405B658D13, xmp.iid:5D8E06000A88DE11B795EE405B658D13, xmp.iid:5E8E06000A88DE11B795EE405B658D13, xmp.iid:5F8E06000A88DE11B795EE405B658D13, xmp.iid:608E06000A88DE11B795EE405B658D13, xmp.iid:618E06000A88DE11B795EE405B658D13, xmp.iid:628E06000A88DE11B795EE405B658D13, xmp.iid:638E06000A88DE11B795EE405B658D13, xmp.iid:58FE234F1288DE11B795EE405B658D13, xmp.iid:59FE234F1288DE11B795EE405B658D13, xmp.iid:5AFE234F1288DE11B795EE405B658D13, xmp.iid:5BFE234F1288DE11B795EE405B658D13, xmp.iid:5CFE234F1288DE11B795EE405B658D13, xmp.iid:5DFE234F1288DE11B795EE405B658D13, xmp.iid:5EFE234F1288DE11B795EE405B658D13, xmp.iid:EF10EAD5EA17DF11BA138BEAC6E1D093, xmp.iid:F010EAD5EA17DF11BA138BEAC6E1D093, xmp.iid:F110EAD5EA17DF11BA138BEAC6E1D093, xmp.iid:F210EAD5EA17DF11BA138BEAC6E1D093, xmp.iid:69676727F417DF11ADFDA9BA796052D2, xmp.iid:6A676727F417DF11ADFDA9BA796052D2, xmp.iid:F93323E8BF73DF118F3C9A53D988F2B2, xmp.iid:FA3323E8BF73DF118F3C9A53D988F2B2, xmp.iid:FB3323E8BF73DF118F3C9A53D988F2B2, xmp.iid:8A3EF219D573DF11B059E781493085D4, xmp.iid:8B3EF219D573DF11B059E781493085D4, xmp.iid:8C3EF219D573DF11B059E781493085D4, xmp.iid:C8E84481D573DF118640FC5775BDC772, xmp.iid:C9E84481D573DF118640FC5775BDC772, xmp.iid:CAE84481D573DF118640FC5775BDC772, xmp.iid:CBE84481D573DF118640FC5775BDC772, xmp.iid:CCE84481D573DF118640FC5775BDC772, xmp.iid:CDE84481D573DF118640FC5775BDC772, xmp.iid:CEE84481D573DF118640FC5775BDC772, xmp.iid:CFE84481D573DF118640FC5775BDC772, xmp.iid:D0E84481D573DF118640FC5775BDC772, xmp.iid:D1E84481D573DF118640FC5775BDC772, xmp.iid:AAB08CACE073DF118640FC5775BDC772, xmp.iid:ABB08CACE073DF118640FC5775BDC772, xmp.iid:ACB08CACE073DF118640FC5775BDC772, xmp.iid:ADB08CACE073DF118640FC5775BDC772, xmp.iid:AEB08CACE073DF118640FC5775BDC772, xmp.iid:AFB08CACE073DF118640FC5775BDC772, xmp.iid:B0B08CACE073DF118640FC5775BDC772, xmp.iid:B1B08CACE073DF118640FC5775BDC772, xmp.iid:B2B08CACE073DF118640FC5775BDC772, xmp.iid:B3B08CACE073DF118640FC5775BDC772, xmp.iid:B4B08CACE073DF118640FC5775BDC772, xmp.iid:212606BDE873DF118640FC5775BDC772, xmp.iid:222606BDE873DF118640FC5775BDC772, xmp.iid:232606BDE873DF118640FC5775BDC772, xmp.iid:242606BDE873DF118640FC5775BDC772, xmp.iid:262606BDE873DF118640FC5775BDC772, xmp.iid:272606BDE873DF118640FC5775BDC772, xmp.iid:282606BDE873DF118640FC5775BDC772, xmp.iid:095B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0A5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0B5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0C5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0D5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0E5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:0F5B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:105B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:115B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:125B9AD1A274DF11B3DEA1215CB0D294, xmp.iid:BBBCD741A974DF11B3DEA1215CB0D294, xmp.iid:BCBCD741A974DF11B3DEA1215CB0D294, xmp.iid:BDBCD741A974DF11B3DEA1215CB0D294, xmp.iid:BEBCD741A974DF11B3DEA1215CB0D294, xmp.iid:BFBCD741A974DF11B3DEA1215CB0D294, xmp.iid:40F0DAB01989DF1198F68FD6B52E4C76, xmp.iid:41F0DAB01989DF1198F68FD6B52E4C76, xmp.iid:42F0DAB01989DF1198F68FD6B52E4C76, xmp.iid:43F0DAB01989DF1198F68FD6B52E4C76, xmp.iid:E278D3481794DF11BDA1F49B1D924AF3, xmp.iid:E378D3481794DF11BDA1F49B1D924AF3, xmp.iid:E478D3481794DF11BDA1F49B1D924AF3, xmp.iid:E578D3481794DF11BDA1F49B1D924AF3, xmp.iid:4F2A737D3194DF11AEA8ADCDFE3B9F59, xmp.iid:502A737D3194DF11AEA8ADCDFE3B9F59, xmp.iid:512A737D3194DF11AEA8ADCDFE3B9F59, xmp.iid:522A737D3194DF11AEA8ADCDFE3B9F59, xmp.iid:532A737D3194DF11AEA8ADCDFE3B9F59, xmp.iid:5B439BF8F89BDF11B064E3C68DAFA757, xmp.iid:5C439BF8F89BDF11B064E3C68DAFA757, xmp.iid:61439BF8F89BDF11B064E3C68DAFA757, xmp.iid:8CF4D42D65C2DF1194749C49D170861A, xmp.iid:8DF4D42D65C2DF1194749C49D170861A, xmp.iid:F169224265C2DF1194749C49D170861A, xmp.iid:92DD7F7620ECDF11AFDB8CC113FAD064, xmp.iid:108AB99720ECDF11AFDB8CC113FAD064, xmp.iid:7DD2FF9D20ECDF11AFDB8CC113FAD064, xmp.iid:7ED2FF9D20ECDF11AFDB8CC113FAD064, xmp.iid:287C968F21ECDF11AFDB8CC113FAD064, xmp.iid:D672611323ECDF1197BEABDEBDFA9DB2, xmp.iid:287E545723ECDF1197BEABDEBDFA9DB2, xmp.iid:297E545723ECDF1197BEABDEBDFA9DB2, xmp.iid:E8EC217923ECDF1197BEABDEBDFA9DB2, xmp.iid:C693C84E24ECDF11BE4787E766A80961, xmp.iid:C793C84E24ECDF11BE4787E766A80961
History When                    : 2009:08:10 09:42:48-05:00, 2009:08:10 09:42:52-05:00, 2009:08:10 09:54:35-05:00, 2009:08:10 09:57:51-05:00, 2009:08:10 10:02:18-05:00, 2009:08:10 10:04:53-05:00, 2009:08:10 10:05:34-05:00, 2009:08:10 10:05:34-05:00, 2009:08:10 10:16:24-05:00, 2009:08:10 10:48:56-05:00, 2009:08:10 11:24:59-05:00, 2009:08:10 11:58:14-05:00, 2009:08:10 14:05:28-05:00, 2009:08:10 15:51:58-05:00, 2009:08:10 16:09:01-05:00, 2009:08:12 08:44:26-05:00, 2009:08:12 08:53:15-05:00, 2009:08:12 08:58:29-05:00, 2009:08:12 09:04:11-05:00, 2009:08:12 09:20:22-05:00, 2009:08:12 09:25:34-05:00, 2009:08:12 09:50:01-05:00, 2009:08:12 09:51:33-05:00, 2009:08:12 10:20:13-05:00, 2009:08:12 11:09:23-05:00, 2009:08:12 11:11:01-05:00, 2009:08:12 11:20:08-05:00, 2009:08:12 11:20:50-05:00, 2009:08:12 11:31:50-05:00, 2009:08:12 11:49:01-05:00, 2009:08:12 12:59:09-05:00, 2009:08:12 13:08:19-05:00, 2009:08:12 13:23:50-05:00, 2009:08:12 13:31-05:00, 2009:08:12 13:34:20-05:00, 2009:08:12 13:39:56-05:00, 2009:08:12 13:43:06-05:00, 2009:08:12 13:45:02-05:00, 2009:08:12 13:45:51-05:00, 2009:08:12 13:48:53-05:00, 2009:08:12 13:57:39-05:00, 2009:08:12 13:57:49-05:00, 2009:08:12 14:17:05-05:00, 2009:08:12 14:19:59-05:00, 2009:08:12 14:36:50-05:00, 2009:08:12 14:38:21-05:00, 2009:08:12 16:07:02-05:00, 2009:08:13 07:34:41-05:00, 2009:08:13 07:39:40-05:00, 2009:08:13 07:41:14-05:00, 2009:08:13 07:43:57-05:00, 2009:08:13 07:54-05:00, 2009:08:13 07:58:54-05:00, 2009:08:13 07:59:12-05:00, 2009:08:13 08:05:39-05:00, 2009:08:13 08:10:55-05:00, 2009:08:13 08:15:45-05:00, 2009:08:13 08:17:52-05:00, 2009:08:13 08:24:46-05:00, 2009:08:13 08:27:05-05:00, 2009:08:13 08:57:58-05:00, 2009:08:13 08:59:53-05:00, 2009:08:13 09:00:32-05:00, 2009:08:13 09:01:04-05:00, 2009:08:13 09:02:03-05:00, 2009:08:13 09:05:08-05:00, 2009:08:13 10:33:27-05:00, 2009:08:13 11:13:31-05:00, 2009:08:13 11:40:25-05:00, 2009:08:13 11:42:12-05:00, 2009:08:13 11:44:45-05:00, 2009:08:13 11:51:54-05:00, 2010:02:12 09:25:22-06:00, 2010:02:12 09:26:41-06:00, 2010:02:12 09:27:36-06:00, 2010:02:12 09:30:32-06:00, 2010:02:12 10:32:04-06:00, 2010:02:12 10:41:12-06:00, 2010:06:09 09:36:35-05:00, 2010:06:09 09:37:50-05:00, 2010:06:09 09:37:50-05:00, 2010:06:09 09:41:34-05:00, 2010:06:09 09:41:50-05:00, 2010:06:09 09:41:50-05:00, 2010:06:09 09:44:27-05:00, 2010:06:09 09:44:52-05:00, 2010:06:09 10:00:14-05:00, 2010:06:09 10:05:19-05:00, 2010:06:09 10:07:42-05:00, 2010:06:09 10:08:26-05:00, 2010:06:09 10:25:20-05:00, 2010:06:09 10:43:34-05:00, 2010:06:09 10:46:56-05:00, 2010:06:09 10:57:11-05:00, 2010:06:09 11:04:24-05:00, 2010:06:09 11:07:52-05:00, 2010:06:09 11:13:42-05:00, 2010:06:09 11:16:52-05:00, 2010:06:09 11:18:32-05:00, 2010:06:09 11:21:17-05:00, 2010:06:09 11:44:42-05:00, 2010:06:09 11:44:49-05:00, 2010:06:09 11:47:41-05:00, 2010:06:09 11:54:11-05:00, 2010:06:09 11:55:09-05:00, 2010:06:09 12:02:08-05:00, 2010:06:09 12:04:07-05:00, 2010:06:09 13:10:12-05:00, 2010:06:09 13:10:59-05:00, 2010:06:09 13:15:44-05:00, 2010:06:09 13:19:48-05:00, 2010:06:09 16:01:59-05:00, 2010:06:10 10:14:09-05:00, 2010:06:10 10:17:05-05:00, 2010:06:10 10:19:50-05:00, 2010:06:10 10:22:33-05:00, 2010:06:10 10:24:40-05:00, 2010:06:10 10:24:45-05:00, 2010:06:10 10:27:43-05:00, 2010:06:10 10:52:47-05:00, 2010:06:10 10:53:26-05:00, 2010:06:10 10:57:59-05:00, 2010:06:10 11:00:14-05:00, 2010:06:10 11:06:52-05:00, 2010:06:10 11:08:13-05:00, 2010:06:10 11:10:15-05:00, 2010:06:10 11:11:19-05:00, 2010:07:06 11:15:27-05:00, 2010:07:06 11:20:39-05:00, 2010:07:06 11:23:34-05:00, 2010:07:06 11:24:12-05:00, 2010:07:20 11:55:12-05:00, 2010:07:20 11:57:12-05:00, 2010:07:20 12:00:55-05:00, 2010:07:20 12:03:10-05:00, 2010:07:20 14:03:32-05:00, 2010:07:20 14:04:50-05:00, 2010:07:20 14:06:48-05:00, 2010:07:20 14:07:57-05:00, 2010:07:20 14:08:55-05:00, 2010:07:30 13:52:43-05:00, 2010:07:30 13:55:02-05:00, 2010:07:30 14:11:44-05:00, 2010:09:17 09:09:26-05:00, 2010:09:17 09:09:26-05:00, 2010:09:17 09:10-05:00, 2010:11:09 10:43:21-06:00, 2010:11:09 10:44:17-06:00, 2010:11:09 10:44:27-06:00, 2010:11:09 10:46:20-06:00, 2010:11:09 10:51:13-06:00, 2010:11:09 11:02:03-06:00, 2010:11:09 11:03:57-06:00, 2010:11:09 11:04:54-06:00, 2010:11:09 11:04:54-06:00, 2010:11:09 11:10:52-06:00, 2010:11:09 11:11:30-06:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /, /metadata, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata
Create Date                     : 2010:11:09 11:13:33-06:00
Modify Date                     : 2010:11:09 11:13:44-06:00
Metadata Date                   : 2010:11:09 11:13:44-06:00
Creator Tool                    : Adobe InDesign CS5 (7.0.3)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 9865 bytes, use -b option to extract), (Binary data 11951 bytes, use -b option to extract)
Doc Change Count                : 9848
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 12
Creator                         : Adobe InDesign CS5 (7.0.3)

EXIF Metadata provided by EXIF.tools

Greenheck Fan 474051 Users Manual

474051 to the manual 5d2489e4-d1d5-4d37-927c-2cd170f2566b

Navigation menu

Versions of this User Manual:

Views

Navigation