Greenheck Fan Dfd 150X Series Users Manual
DFD-150X series to the manual 647a70ec-2f22-4732-9f3c-bd3fee1f91d8
2015-02-09
: Greenheck-Fan Greenheck-Fan-Dfd-150X-Series-Users-Manual-562536 greenheck-fan-dfd-150x-series-users-manual-562536 greenheck-fan pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
DFD-150X series Dynamic Rated FIRE DAMPERS with Sleeve 11⁄2 Hour Fire Resistance Rating APPLICATION Model DFD-150X is approved for use in walls, floors and partitions with fire resistance ratings less than 3 hours. This model carries a 11⁄2 hour UL fire damper label. UL 555 classifies dynamic rated fire dampers for use in HVAC systems that are operational in the event of fire . RATINGS UL555 Fire Resistance Rating Fire Rating: 1 1/2 hours Dynamic closure rating Maximum Velocity: 4000 fpm (20.3 m/s) up to 24 in. x 24 in. (610mm x 610mm) 2000 fpm (10.2 m/s) above 24 in. x 24 in. (610mm x 610mm) Maximum Pressure: 4 in. wg (1 kPa) Model DFD-150X meets the requirements for fire dampers established by: National Fire Protection Association (NFPA Standards 80, 90A & 101) BOCA National Building Codes ICBO Uniform Building Codes (UBC Standard 43-7) SBCCI Standard Building Codes New York City (MEA listing #260-91-M) California State Fire Marshall (Listing #3225-981:102 for use in walls) “UL CLASSIFIED (see complete marking on product)” “UL CLASSIFIED to Canadian safety standards (see complete marking on product)” Standard 555 (Listing #R13317) CONSTRUCTION Damper is galvanized steel (in gauges required by UL listing R-13317) sleeve is 20 ga. galvanized steel. Damper Sleeve P* STANDARD FEATURES • Stainless steel closure springs • Fusible links (165ºF (74ºC) standard, 212ºF (100ºC) and 286ºF (141ºC) available. • Horizontal or vertical mount available H* Fusible Link (replaceable) OPTIONAL FEATURES • Security bars • One piece retaining angles (POC) • Transitions (B, C, CO, CR, & R) • Steel stud connection • Sealed transitions and sleeves K Damper Location CL Damper Fram e W * Overall Sleeve Length 10 in. (305mm) = DFD-150X10 12 in. (305mm) = DFD-150X12 14 in. (356mm) = DFD-150X14 16 in. (406mm) = DFD-150X16 HORIZONTAL VERTICAL MOUNT Damper Sleeve * These dimensions are furnished approximately 1⁄4 in. (6mm) undersize. P* H* K Fusible Link (replaceable) (165º F Std., 212º available) CL Damper Frame K Damper CL Damper Fram e Location Overall Sleeve Length 12 in. (305mm) = FD-150X12 14 in. (356mm) = FD-150X14 16 in. (406mm) = FD-150X16 VERTICAL MOUNT W* HORIZONTAL MOUNT DFD-150X Type A Dampers larger than maximum single section size are supplied in 2 or more sections of equal size. The following chart and illustrations show minimum and maximum damper section size and assembly configurations for multi-section dampers. Blade Stack Dimensional Data SIZE LIMITATIONS Inches (mm) Type A Type B minimum maximum minimum maximum 6x4 (152 x 102) 36 x 36 (914 x 914) 6x6 (152 x 152) 36 x 32 (914 x 813) Multi Section** Vertical NA 72 x 48 (1829 x 1219) or 60 x 60 (1824 x 1524) NA 72 x 45 (1829 x 1143) or 60 x 56 (1524 x 1422) Single Section Horizontal 6x4 (152 x 102) 30 x 30 (762 x 762) 6x6 (152 x 152) 30 x 26 (762 x 660) Multi Section** Horizontal NA 48 x 36 (1219 x 914) NA 48 x 32 (1219 x 813) Single Section Vertical Installation of sizes larger than the maximums shown requires approval of the authority having jurisdiction. ** Consult factory for number of sections. 1 Maximum Single Section Dimensions 36in. max. (914mm) 36 in. max. (914mm) 2 Multi-section limitations Maximum height is 48 in. (1219mm) when width is 72 in. (1829mm) or less. 48 in. (1219mm) max. P H* W* H* P in. mm in. mm 8 203 1.2 30 9 229 1.3 33 10 254 1.3 33 11 279 1.4 36 12 305 1.6 41 13 330 1.7 43 14 356 1.8 46 15 381 1.8 46 16 406 2.0 51 17 432 2.1 53 18 457 2.2 56 19/37/38 483/940/965 2.3 58 20/39/40 508/991/1016 2.4 61 21/41/42 533/1041/1067 2.6 66 22/43/44 559/1092/1118 2.6 66 23/45/46 584/1143/1168 2.7 69 24/47/48 610/1194/1219 2.9 74 25/49/50 635/1245/1270 3.1 79 26/51/52 660/1295/1321 3.2 81 27/53/54 686/1346/1372 3.2 81 28/55/56 711/1397/1422 3.3 84 29/57/58 737/1448/1473 3.4 86 30/59/60 762/1499/1524 3.6 91 31/32 787/813 3.7 94 33/34 838/864 3.9 99 35 889 4.1 104 36 914 4.2 107 These dimensions are furnished *approximately 1/4 in. (6mm) undersize. 72 in. (1829mm) max. DFD-150X Type B Dampers larger than maximum single section size are supplied in 2 or more sections of equal size. The following chart and illustrations show minimum and maximum damper section size and assembly configurations for multi-section dampers. Type B Overall Damper Dimensions 1 Maximum Single Section Dimensions H* O* 32 in. (813mm) max. W* 36 in. (914mm) max. 2 Multi-section limitations Maximum height is 45 in. (1143mm) when width is 72 in. (1829mm) or less. 45 in. (1143mm) max. 72 in. (1829mm) max. H* O* H* O* 6 (152) 8 (203) 32(813) 36 (914) 7 (178) 9 (229) 33 (838) 36 (914) 8 (203) 10 (254) 34 (864) 37 (940) 38 (965) 9 (229) 11 (279) 35 (889) 10 (254) 12 (305) 36 (914) 39 (991) 11 (279) 13 (330) 37 (940) 40 (1016) 12 (305) 14 (356) 38 (965) 41 (1041) 13 (330) 15 (381) 39 (991) 42 (1067) 14 (356) 16 (406) 40 (1016) 43 (1092) 15 (381) 18 (457) 41 (1041) 44 (1118) 16 (406) 19 (483) 42 (1067) 45 (1143) 17 (432) 20 (508) 43 (1092) 46 (1168) 18 (457) 21 (533) 44 (1118) 47 (1194) 19 (483) 22 (559) 45 (1143) 48 (1219) 20 (508) 23(584) 46 (1168) 50 (1270) 21 (533) 24 (610) 47 (1194) 51 (1295) 22 (559) 26 (660) 48 (1219) 52 (1321) 23 (584) 27 (686) 49 (1245) 53 (1346) 24 (610) 28 (711) 50 (1270) 54 (1372) 25 (635) 29 (737) 51 (1295) 55 (1397) 26 (660) 30 (762) 52 (1321) 56 (1422) 27 (686) 31 (787) 53 (1346) 57 (1448) 28 (711) 32 (813) 54 (1372) 58 (1473) 29 (737) 33 (838) 55 (1397) 59 (1397) 30 (762) 34 (864) 56 (1422) 60 (1524) 31(787) 35 (889) * These dimensions are furnished approximately 1/4 in. (6mm) undersize. (All ‘H’ dimensions larger than single section height are two sections high. Refer to chart. The top section is a Type B and the bottom sections are Type A). DFD-150X Types CR, CO & C DFD-150X dampers with C, CO, CR, and R transitions are available only as single section dampers. The following chart show minimum and maximum damper size. Dimensions are in inches (mm in parentheses). Type CR inches (mm) Minimum Type R*1 Type CO & C Maximum Minimum Maximum Minimum D*+2 Type CR Maximum Single Section Vertical 6 (152) 31 (787) 6x5 (152 x 127) 34 x 31 (864 x 787) 6 (152) 34 (864) Single Section Horizontal 6 (152) 31 (787) 6 x 5 (152 x 127) 34 X 31 (864 X 787) 6 (152) 34 (864) O* D* W*+2 Type CO O* *1 With 2 in. (50mm) offset. Sizes adjust with 1 in.(25mm) offset. H* W* C, CO, CR transitions are positioned 1 in. (25mm) from bottom of sleeve. W*+2 Type C O* H* Type CR Type R Steel Stud Frame W* 31in. (787mm) max. 34 in. (787mm) max. O* 5 (127) 8 (203) 6 (152) 9 (229) 7 (178) 10 (254) 8 (203) 11 (279) 9 (229) 12 (305) 10 (254) 13 (330) 11 (279) 14 (356) 12 (305) 15 (381) 13 (330) 16 (406) 14 (356) 17 (432) 15 (381) 19 (483) 16 (406) 20 (508) 17 (432) 21 (533) 18 (457) 22 (559) 19 (483) 23 (584) 20 (508) 24 (610) 21 (533) 25 (635) 22 (559) 27 (686) 23 (584) 28 (711) 24 (610) 29 (737) 25 (635) 30 (762) 26 (660) 31 (787) 27 (686) 32 (813) 28 (711) 33 (838) 29 (737) 34 (894) 30 (762) 35 (889) 31 (787) 36 (914) A A- H or D* Type C Type CO 31 in. (787mm) Max 31 in. (787mm) Max 34 in. (864mm) Max 34 in. (864mm) Max Steel Stud Wall Steel Stud Connection (SSC) Option The Steel Stud Connection (SSC) Option allows fastening of the damper sleeve (up to 36 in. W x 36 in. H [914mm x 914m]) directly to the wall's steel stud framing. This option replaces the angles that were previously required for wall installations. Steel Stud Frame Wallboard Steel Stud Frame Retaining Bar A A- Cross-Section A-A Steel Stud Wall Damper Sleeve * Dimension are in inches (mm). These dimensions are furnished approximately 1/4 in. (6mm) undersize. Copyright © 2008 Greenheck Fan Corporation DFD-150X series Rev. 13 July 2008 Wallboard Steel Stud Frame
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-702 Create Date : 2008:07:18 15:41:10-05:00 Metadata Date : 2008:07:23 14:02:58-05:00 Modify Date : 2008:07:23 14:02:58-05:00 Creator Tool : Adobe InDesign CS3 (5.0.2) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9478 bytes, use -b option to extract) Instance ID : uuid:548365b3-9319-4fc0-a3b7-95347c31b477 Document ID : adobe:docid:indd:172e94e0-5730-11dc-b23a-82c4ca82118a Rendition Class : proof:pdf Derived From Instance ID : c2f69965-1cd4-11db-94f4-c840e2e21037 Derived From Document ID : adobe:docid:indd:f0e1179f-6682-11da-85b9-e7cb4b3c0c48 Manifest Link Form : ReferenceStream Manifest Placed X Resolution : 72.00 Manifest Placed Y Resolution : 72.00 Manifest Placed Resolution Unit : Inches Manifest Reference Instance ID : uuid:109843B83F94DA11BAD1D23B39E671BC Manifest Reference Document ID : uuid:0F9843B83F94DA11BAD1D23B39E671BC Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 4 Creator : Adobe InDesign CS3 (5.0.2)EXIF Metadata provided by EXIF.tools