Group Sense Mobile Tech B148 RFID Module User Manual

Group Sense Mobile-Tech Limited RFID Module Users Manual

Users Manual

1 DT430 Expansion Modules Quick Start Guide
2Copyright Copyright2011 Group Sense Mobile-Tech Limited. All rights reserved. No part of this document may be reproduced, distributed, translated, or stored in any form without the prior written permission of Group Sense Mobile-Tech Limited. All brands and product names mentioned herein may be trademarks or registered trademarks of their respective owners. Product specifications are subject to change without prior notice. Disclaimer The contents of this document are provided as is. Group Sense Mobile-Tech Limited makes no representations or warranties with respect to the contents herein and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. Group Sense Mobile-Tech Limited reserves the right to revise this document at any time without prior notice.
3Regulatory Information FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement This device should be installed and operated with a minimum separation distance of 20cm between the radiator and all persons. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. CE Statement This device has been tested and found to comply with the following EU Directives:  R&TTE Directive (1999/5/EC)  EMC Directive (2004/108/EC)  Low Voltage Directive (2006/95/EC) The assessment of compliance of the device was performed according to the following European standards:  EMC: EN 301 489-1/-17  Health: EN 50371  Safety: EN60950-1  Radio: EN 300 328
4Laser Warning Statement Barcode scanner expansion module contains Class 2 type laser scan engine. The scanner and imager engine meet the accessible laser light limits for an CDRH/IEC Class 2 laser and IEC Class 1M LED product. The following applies to the scan engine.  “Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.”  “EN60825-1:1994+ A1:2002 +A2:2001”  “IEC60825-1:1993+A1:1997+A2:2001”  “Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.” Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. A laser warning label such as the one below should appear on the end product.
5Safety Information Please read the following information carefully before using the device for the first time, and keep this Quick Guide in a safe place for future reference.  Do not stare directly into the laser beam, or direct the laser beam into eyes.  Always treat the device with care and keep it in a clean and dust-free environment.  Do not expose the device to extremely hot, cold or humid environment.  Do not use the device in wet or rainy conditions.  Do not charge the device in extremely hot or cold conditions.  Do not attempt to disassemble or modify the device including the charger.  Do not operate the device when your hands are wet.  Do not insert foreign objects into the openings of the device.  Use only the charger and battery approved for the device.  Install the cradle on a flat and stable surface.  Do not cascade over 3 cradles.  Do not use the charger if the power cord or plug is damaged.  Do not disassemble, crush or puncture the battery.  Do not expose the battery to high temperatures.  Do not let battery terminals touch other metal objects that could lead to short-circuit of the battery.  Do not dispose of the battery in fire or water.  Dispose of used battery properly according to local laws and regulations.
6DT430 Expansion Module Overview Module Model No. Module Type DT430 (1D) 1D Barcode Scanner DT430 (2D) 2D Barcode Scanner DT430 (RFID) RFID Reader Installing the Expansion Module To install the Expansion Module 1. Turn over the DT430 handheld terminal. 2. Remove the two screws on the DT430 back cover with a screw driver. 3. Remove the back cover from DT430. 4. Insert the Expansion Module into DT430 module slot, and slide the module until it fits tightly in the slot. 5. Apply the back cover screws to fasten the Expansion Module.
7Scanning Barcodes 1. Aim the barcode reader aperture of the handheld at the barcode. 2. Press Right Scan Key or Left Scan Key to scan the barcode. 3. If scanning is not able to complete and time-out, try adjusting the angle or distance between the handheld and the barcode; and press Right Scan Key or Left Scan Key to scan again. Correct linear scanning Incorrect linear scanning Correct imager scanning Incorrect imager scanning Remarks: Left and Right Scan Keys must be pre-figured by application developers.
8Scanning RFID Tags 1. Hold the handheld with the RFID expansion module parallel to and directly above the RFID tag. The scanning distance should be kept 3cm at most. 2. Press Right Scan Key or Left Scan Key to scan the barcode. Correct RFID tag scanning Position handheld parallel to the tag. Keep scanning distance within 3cm. Incorrect RFID tag scanning Do not hold the handheld perpendicular to the tag. Do not position the handheld at an angle or too far from the tag. Remarks: Left and Right Scan Keys must be pre-figured by application developers.
9 Copyright2011 Group Sense Mobile-Tech Limited, All rights reserved. http://www.gsml.com.hk

Navigation menu