Guangzhou Rayer Acoustic Technology BTN2 Bluetooth Speaker User Manual BTN2

Download:
Mirror Download [FCC.gov]
Document ID	2654381
Application ID	Y0J6Sv3vGH7mDsu2CLscQw==
Document Description	BTN2 User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	62.61kB (782623 bits)
Date Submitted	2015-06-22 00:00:00
Date Available	2015-06-24 00:00:00
Creation Date	2015-05-28 13:47:32
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-05-28 13:47:41
Document Title	BTN2 User Manual
Document Creator	Adobe InDesign CS6 (Windows)

Owner’s Guide
Bluetooth Speaker: BTN2
High Performance
Bluetooth Speaker
Revision 05282015
Model: BTN 2
Serial No. ________________
CONGRATULATIONS
Thank you for purchasing this Hitachi product.
Please read these instructions carefully.
For additional assistance please call Toll Free
800.HITACHI (800.448.2244)
or visit our website at www.hitachi.us/tv.
Keep this owner’s guide for future reference.
Record the serial number of your
Bluetooth speaker for future reference. This information
is located on the bottom of the speaker unit.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO
PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR
OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL
TIMES.
CAUTION : TO PREVENT ELECTRIC SHOCK, DO NOT USE THE
AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
WARNING: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
E-WASTE / RECYCLE NOTICE
This product may contain lead and should be disposed or recycled
according to local electronic waste (e-waste) laws. For product recycling
and disposal information, contact your local government agency or www.
eRecycle.org (in California), the Electronic Industries Alliance at www.
ecyclingcentral.com (in the U.S.) or the Electronic Product Stewardship
Canada at www.epsc.ca (in Canada). FOR MORE
INFORMATION, call 800.HITACHI (800.448.2244) (USA/
CANADA).
CAUTION: • To comply with FCC RF exposure compliance requirements, a separation distance of at least 8 inches must be
maintained between the speaker unit of this device and
all persons.
• This product’s transmitter must not be co-located or
operated in conjunction with any other antenna or
transmitter.
• Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules
could void the user’s authority to operate this product.
CAUTION: The speaker unit’s battery pack is not user replaceable.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the
“E-WASTE/RECYCLE NOTICE”.
Declaration of Conformity
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference and (2) This device must accept any interference
received, including interference that may cause undesired operation.
For questions regarding this declaration, contact:
		Hitachi America, Ltd.
2420 Fenton Street, Suite 200
		Chula Vista, CA 91914-3556
Tel: 800.HITACHI (800.448.2244)
ATTN: Customer Relations
CONDENSATION
Moisture will form in the operating section of the product if the
product is brought from cool surroundings into a warm room or if the
temperature of the room rises suddenly. If this occurs, the product's
performance may be impaired temporarily. To prevent this, let the
product stand in its new surroundings for about an hour before
switching it on, or make sure that the room temperature rises gradually.
Condensation may also form during the summer if the product is
exposed to the breeze from an air conditioner. In such cases, change
the location of the product.
IMPORTANT SAFETY INSTRUCTIONS
1)
Read these instructions.
2)
Keep these instructions.
3)
Heed all warnings.
4)
Follow all instructions.
5)
Do not use this product near water.
6)
Clean only with dry cloth.
7)
Do not block any ventilation openings. Install only in accordance
with instructions in this owner’s guide.
8)
Do not install near any heat sources such as radiators, heat
registers, stoves, or any other apparatus (including amplifiers)
that produces heat.
9)
Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10)
Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the product.
11)
Only use attachments/accessories specified by the
manufacturer.
12)
Use only with cart, stand, tripod, bracket, or table
specified by the manufacturer or sold with the product
(if any). When a cart is used, use caution when moving
the cart/product combination to avoid injury from tipover.
13)
Unplug this product during lightning storms or when unused for
long periods of time.
14)
This product does not contain any serviceable or replaceable
parts. Do not attempt to service or repair this product. Opening,
or attempting to service or repair, this product will void the
IMPORTANT SAFETY INSTRUCTIONS
(continued)
manufacturer’s limited warranty. If operational problems are
encountered during the product’s limited warranty period, please
contact 800.HITACHI.
15)
Product should not be exposed to dripping or splashing, and
objects filled with liquids, such as vases, should not be placed
on the product.
16)
Do not overload wall outlets and extension cords, as this can
result in a risk of fire or electric shock.
17)
Do not push objects through any openings in this unit, as they
may touch dangerous voltage points or short out parts that could
result in fire or electric shock. Never spill or spray any type of
liquid into the unit.
Charging the Battery
1) This battery powered speaker uses an internal rechargeable
battery.
2) Important Note: The battery is not replaceable. Do not attempt to
replace the battery.
3) Connect the speaker to a USB port with a minimum 5V/1A rating.
4) Important Note: For the best performance, the first time you charge
the battery please allow the battery to fully charge before using.
(Approximately 2.5 hours)
4) When charging, the power key light will flash to indicate that
charging is active.
5) Playing music while charging will extend the charging time.
6) When charging is complete the power key light will stop flashing.
Package Contents
•
•
•
•
Speaker Unit
USB charging cable
3.5mm audio cable
Owner’s Guide
Product Layout
④ Power on/off
⑤ MIC
① Vol+/Next
② Vol- /Previous
③Bluetooth Pairing/Hands Free/Play/Pause
⑥ Line In
⑦ Reset
⑧ Micro USB
Charging Input
j Vol+/Next: Increase volume.
k Vol-/Previous: /Decrease volume.
l Bluetooth Pairing/Hands Free/Play/Pause: See table
on page 9.
m Power On/Off: Short press to power on, long press
(press and hold) to power off. Battery charging and
status light.
n MIC: Microphone.
o Line In: 3.5mm input for external sources.
p Reset: Press to power off the speaker if the speaker
stops responding.
q Micro USB Charging Input: Used to charge the speaker’s battery.
1 Bluetooth button operation
(Pairing/Hands Free/Play-Pause):
Bluetooth button
Speaker Status
Long press
Bluetooth mode
Disconnect Bluetooth
Speaker Status
Short press
Bluetooth mode with an
incoming call
Answer the incoming call
Bluetooth mode with a call
End the call
Bluetooth mode & Music
playing
Play / Pause
Line In mode & Music
playing
Mute
Speaker Status
Double press
Bluetooth mode
Call back
Bluetooth mode with an
incoming call
Refuse the incoming call
2 Vol +/Vol - button operation
(Volume/Next/Previous):
Vol+/Vol- button
Speaker Status
Short/Long press
Bluetooth mode
Volume up/Volume down
Line in mode
Volume up/Volume down
Speaker Status
Double press
Bluetooth mode
Next/Previous song
2 Playing Music
2.1 Bluetooth mode:
1. Power on the speaker. The Bluetooth button will
blink continuously indicating that the speaker is
ready to pair with a device.
2. On your Bluetooth enabled device search for and
pair with the Hitachi Bluetooth speaker “BTN2”.
When pairing is successful the Bluetooth button
will stop blinking. You are now ready to listen to
music on your Hitachi Bluetooth speaker.
3. If you need to unpair an already paired Bluetooth
device and switch to another device, press and
hold the Bluetooth button until the Bluetooth
button starts to blink. The speaker is now ready for
pairing consistent with step 1 above.
4. When the speaker is powered on, it will automatically connect to the last paired device.
10
2.2 Line In mode:
When a 3.5mm audio cable is inserted into the LINE IN
input, the speaker will automatically switch to the LINE
IN input. Connect one end of the 3.5mm audio cable to
the speaker unit and the other end to the device you wish
to play music from. To switch back to Bluetooth mode,
disconnect the 3.5mm audio cable.
3 How to clean the speaker
1. Always power off the speaker before cleaning it.
2. Do not use volatile solvents (such as ethanol, rosin, or toluene solvents) to clean the speaker. These
types of chemicals may damage the speaker.
3. Use a cotton or microfiber cleaning cloth.
4. When cleaning the speaker, do not directly put water on the speaker’s enclosure. Lightly moisten a
cotton or microfiber cleaning cloth and then gently
wipe down the speaker.
4 Low battery warning
When the battery is low in charge, the speaker will output
a warning sound every 1 minute and the power key will
flash.
11
Troubleshooting
The following table contains common problems
and solutions. Please read carefully.
Problem
Solution
The speaker • Make sure the speaker was charged
has no sound
before use.
• Increase the volume settings on the
source and speaker.
• Make sure the cable is correctly
connected.
• Make sure that the audio playback
device is connected and in play mode.
Humming
noise or
distorted
sound
• Make sure that the cable is correctly
connected.
• Ensure that the device that is connected to the speaker is not the source of
the humming noise or distortion.
• Replace the audio cable.
Not charging
• Ensure that the Micro USB charging
cable is connected correctly.
• Ensure that the Micro USB charging
cable can charge other equipment
normally.
Bluetooth
pairing fails
• Check that the speaker is in the pairing
state (Bluetooth button is blinking). If
it is not, press and hold the Bluetooth
button (until it blinks) to set the speaker to pairing mode and pair again.
• Make sure that the Line In (3.5mm)
cable is disconnected.
12
Audio is
• Ensure that the speaker and Bluetooth
interrupted or
device to which it is connected are
breaks up
within 33 feet (10 meters) of each
other.
• Ensure that there is no obstruction between the speaker and the connected
Bluetooth device.
Speaker is
not responding and will
not turn off
• Locate the small pinhole marked
RESET located on the right side of the
speaker (under the protective, rubber
cover). Insert a straightened paper
clip through the pinhole and depress
the switch inside. The speaker unit will
automatically power off.
13
Care and Maintenance
• Keep all parts out of reach of children.
• Keep the speaker dry. Precipitation, humidity and other liquids containing minerals can corrode electronic
circuits.
• Do not use or store in dusty or dirty areas.
• Do not store in hot areas. High temperatures can
shorten the life of electronic devices and warp or melt
certain plastics.
• Do not store in very cold areas. Moisture can form
inside the case, which may damage electronic circuit
boards.
• Do not attempt to open the case. Non-expert handling of the device may damage the system.
• Avoid dropping or strong shocks.
14
Specifications
Model Name
BTN2
Speaker
2 x 1.5 inch full frequency speaker,
3W, 4ohm
Frequency response
100Hz-20KHz (+/-3dB)
Power amplifier
Class D @ 3 W × 2 CH
THD (Distortion Ratio)
< 10% @ 500 mV/1kHz
SNR (Signal to Noise Ratio)
>75dB(A)
Sound pressure level
93dB± 3dB (500mV@1M)
Play mode
Bluetooth/Line In
Charging input
DC 5V,1A (Micro USB)
Battery
Lithium polymer battery/3.7V/
1300mAh/4.8Wh
Dimensions
6 5/16 (W) x 3 1/8 (H) x 1-1/8 (D)
inches;
16.0 (W) x 7.7 (H) x 2.9 (D) cm
Weight
0.6lbs (300g)
Bluetooth version
BT2.1+EDR
Bluetooth Range
10m (Line of sight)
Hands-free
DSP MIC hands-free system
Note: Specifications subject to change without notice
15
IP54
This product has an IP54 water and dust resistant design. It can
tolerate a limited splash of water, but do not let this product be
submerged in water or overly soaked. If liquid is spilled onto the
surface of this product, please use a dry cloth or paper towel to
wipe it off; if water is immersed inside the product, please immediately shut it down and contact the customer service center.
Definition of IP54:
1. IP5X + IPX4 = IP54, the standard definition of these 2 items:
• Dust prevention level IP5X: Prevents harmful dust from
accumulating.
• Water prevention level IPX4:Liquid splashing the surface
from all direction will do no harm.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Hitachi is under license. Other trademarks and trade
names are those of their respective owners.
16
800.HITACHI
(800.448.2244)
Monday ~ Friday
9:00 am - 6:00 pm EST
www.hitachi.us/tv
HITACHI AMERICA, LTD., DIGITAL MEDIA DIVISION
HITACHI has made every effort to assure you enjoy trouble free operation from your Hitachi
product. Should you require service assistance with OPERATIONAL, HOOK UP, TECHNICAL
ASSISTANCE OR WARRANTY SERVICE SUPPORT,
please contact 800.HITACHI (800.448.2244).
Please be prepared to submit proof of purchase and/or delivery receipts to your 800.HITACHI
Customer Service Representative. Warranty coverage will be provided in accordance with the
provisions of your Limited Warranty (see the Limited Warranty page in this operating guide).
Pour de plus amples renseignements sur le service durant la periode couverte par la garantie,
sur le fonctionnement ou pour de l'assistance techniquie communiquez avec:
Au Canada: 800.HITACHI (800.448.2244)
Lundi ~ Vendredi
9:00 am - 6:00 pm HNE
Hitachi America, Ltd., Digital Media Division
Customer Service Support
P.O. Box 99652
Troy, MI 48099
customerservice.ce@hal.hitachi.com
17
Limited Warranty
(VALID IN THE UNITED STATES AND PUERTO RICO ONLY.)
LIMITED WARRANTY TERMS AND CONDITIONS. Subject to the conditions and
®
limitations set forth below, this HITACHI Bluetooth Speaker product (the “Product”)
is warranted to be free from defects in materials and workmanship for a period of 1
year starting from the original date of purchase (the “Limited Warranty Period”) by
the original purchaser (“Purchaser”). During the Limited Warranty Period, if the
Product does not work properly due to a defect in materials or workmanship, Hitachi
will, at Hitachi’s option, either: (i) repair the Product with new or refurbished parts, or
(ii) replace the Product with a new or refurbished product with equal or greater
features and functions as the Product. If Purchaser rejects, refuses or otherwise
does not accept Hitachi’s repair or replacement offer, this Limited Warranty shall be
void and of no further force or effect. This Limited Warranty extends to the
Purchaser only and is not transferable. To qualify for coverage under this Limited
Warranty, purchaser must notify Hitachi of a warranty claim during the Limited
Warranty Period by calling 800-HITACHI and must provide a dated sales receipt for
the Product.
PARTS AND LABOR: There will be no charge for any replacement parts or labor
required to correct a qualifying defect that arises during the Limited Warranty Period.
Any replacement part used to repair the Product may be, at Hitachi’s option, a new
or refurbished part, and such replacement part will be warranted only for 90 days or
the remainder of the original 1-year Limited Warranty Period, whichever is later.
SERVICE LOCATIONS AND RETURNS: Products must be transported or shipped
to a Hitachi-designated service center (call 800-HITACHI for more information).
Hitachi will not be responsible for any costs of transporting or shipping the Product
to Hitachi-designated service center, but Hitachi will be responsible for the cost of
return-shipping repaired or replacement Product to Purchaser. The purchaser must
obtain pre authorization from Hitachi before shipping any Product to Hitachi for
replacement, and Purchaser must ship the Product with all shipping charges prepaid
using the Product’s original box and packaging, including all original parts, written
materials and accessories.
WARRANTY LIMITATIONS: This Hitachi Limited Warranty does not cover: (a) any
Product that has been modified or repaired in a manner not previously authorized by
Hitachi in writing; (b) any Product whose serial number (if any) has been removed,
altered, replaced, defaced or rendered illegible; (c) any defect, malfunction, or failure
caused by or resulting from non-authorized service, maintenance, repair or part
replacements; (d) damage resulting from abuse, misuse, mishandling, neglect or
damage caused by exposure to hostile or unstable operating environments, such as
areas containing dust and/or smoke, or in any manner other than those identified as
acceptable in the Product’s Owner’s Guide; (e) damage caused by power surges,
accidents, natural disasters/occurrences or any other events or circumstances
18
outside Hitachi’s control; (f) any Product used in any manner inconsistent with the
safe and proper set-up, usage and installation requirements and configurations
identified in the Product’s Owner’s Guide; (g) improper opening, tampering with, or
modification of the Product or any Purchaser misadjustments of user-operated
controls; (h) any obligation related to the removal of Product from a custom cabinet
or other specialized product installation; (i) product knobs, buttons, switches,
batteries or accessories; (j) damage caused by cleaning Product in any manner
other than as specified in the Product’s Owner’s Guide; (j) normal usage or ordinary
wear and tear, including, without limitation, scratches or marks on the Product’s
exterior; (k) any damage to a Product returned to Hitachi or any Hitachi-designated
facility for repair or replacement that is attributable to improper packaging,
mishandling or shipping by Purchaser; (l) any Product purchased or serviced outside
the United States (including Puerto Rico); (m) any Product that has been used for
commercial or industrial purposes; or (n) any Product purchased in non-new or nonfactory-sealed condition, such as in “AS IS”, “refurbished”, “reconditioned,” or
“previously owned” condition or any other similar condition. NO PERSON, AGENT,
DISTRIBUTOR, DEALER, SERVICE FACILITY, OR COMPANY IS AUTHORIZED
TO CHANGE, MODIFY OR AMEND THE TERMS OF THIS LIMITED WARRANTY
IN ANY MANNER WHATSOEVER. EXCEPTAS PROVIDED IN THIS LIMITED
WARRANTY, HITACHI MAKES NO EXPRESS WARRANTY REGARDING THE
PRODUCT. FURTHER, ALL IMPLIED WARRANTIES RELATING TO ANY
PORTION OF THE PRODUCT, INCLUDING, WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY EXPRESSLY DISCLAIMED BY HITACHI TO THE
MAXIMUM EXTENT PREMITTED BY APPLICABLE LAW. HITACHI SHALL NOT
BE LIABLE TO PURCHASER OR TO ANY OTHER PERSON FOR ANY INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR ANY LOSS OF PROFIT,
LOSS OF DATA, OR DAMAGE TO THE PRODUCT
THAT IS ALLEGED TO
HAVE RESULTED FROM ANY DEFECT IN, OR MALFUNCTION OR FAILURE OF,
THE PRODUCT BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS AND/OR THE EXCLUSION OF
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE
LIMITATIONS MAY NOT APPLY TO EVERY PURCHASER. THIS LIMITED
WARRANTY CONFERS SPECIFIC LEGAL RIGHTS, INCLUDING CERTAIN
OTHER RIGHTS THAT MAY VARY DEPENDING ON PURCHASER’S
JURISDICTION. THIS LIMITED WARRANTY SHALL BE GOVERNED BY AND
CONSTRUED IN ACCORDANCE WITH THE LAWS OF THE STATE OF
PURCHASER’S RESIDENCE. FOR QUESTIONS ABOUT THE PRODUCT OR
THIS LIMITED WARRANTY, PLEASE CALL 800.HITACHI OR VISIT
www.hitachiserviceusa.com.
19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2015:05:28 13:47:32-07:00
Metadata Date                   : 2015:05:28 13:47:41-07:00
Modify Date                     : 2015:05:28 13:47:41-07:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:430741c7-6b4f-4050-b576-ae5c53b54b84
Original Document ID            : xmp.did:3BEA8F1E6013E411A7F1C3F51AF23F22
Document ID                     : xmp.id:AF68EFB57A05E511BE17C55ED64E791B
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:AE68EFB57A05E511BE17C55ED64E791B
Derived From Document ID        : xmp.did:AA784C316705E511BE17C55ED64E791B
Derived From Original Document ID: xmp.did:3BEA8F1E6013E411A7F1C3F51AF23F22
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:05:28 13:47:32-07:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 19
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools