NMI Equip Catalog 2016
2016-01-28
: Guide Nmi Equip Catalog 2016 NMI Equip catalog 2016 Niagara Catalog manuals Niagara-Library
Open the PDF directly: View PDF 
.
Page Count: 28
Grinders
Shot Blasters
Scrapers
Dust Collectors
Air Scrubbers
Sweeper/Scrubbers
Diamond Tooling
Floor Saws
Buffers
Burnishers
Rentals
Parts
Service
www.niagaramachine.com
800-622-2048
YOUR ONE-STOP SURFACE PREP SHOP
Niagara Machine, Inc. is a national distributor of quality Lavina® concrete grinding and polishing
machines and diamond tooling, Prep/Master grinding machines, BlastPro® shot blasters and
scrapers, joint filler and floor repair products, concrete treatments, and Ermator® HEPA clean air
vacuums. Over the past 15 years, the company has collaborated with hundreds of businesses
across the country to develop smooth solutions for concrete floors. Whether the existing flooring is
epoxy, carpet or tile, Niagara consults with building and maintenance decision-makers to provide
comprehensive recommendations for new and existing floors, from removal to grinding to final
polishing and maintenance.
Niagara Machine serves as a total resource for the planning, training and equipment required to
transform old concrete floors. The company’s comprehensive equipment line has been selected
through critical performance evaluations of every aspect of surface preparation. Everything is
available under one roof: equipment sales, rentals, densifiers, dyes, joint filler, diamonds, shot
and blades.
Niagara Machine is headquartered in Erie,
PA, and has facilities in Charlotte, NC and
West Berlin, NJ. These three locations
serve as showrooms, warehouses and
repair sites, as well as customer training
facilities where company technicians
provide a step-by-step guide to the
complete concrete grinding, polishing and
finishing process, along with advice in
choosing the proper equipment for specific
applications. Niagara also has field
representative and rental fleets at nine
remote locations. Our representatives are
Niagara employees and draw upon years
of concrete polishing experience to meet
your specific job requirements.
“A good building begins with a good floor. And
when it comes to good concrete floors, Niagara
Machine is your expert resource. We’re distrib-
utors of an incredibly extensive line of grinding,
polishing, and surface preparation equipment,
and floor treatments and abrasives. More
importantly, we offer a level of service that truly
shines.
We listen. We consult. We recommend. We
solve problems. We partner with you from start
to finish, helping you choose the proper
equipment, proper supplies, and the most
efficient and economical process. This part of
our capability—experience and expertise—is
just as important as the quality equipment that
we supply. This is the reason to turn to Niagara.
This is what sets us apart.”
Wade Christensen
Vice President
NIAGARA MACHINE. THE BEST EQUIPMENT AND THE BEST KNOW-HOW!
YOUR ONE-STOP SHOP
At Niagara Machine, excellent customer service is more than a promise: it’s our way of doing
business. We offer numerous sales support functions for the sole purpose of ensuring that
you have the right equipment and right approach that works as effectively and economically
as possible. Take a look at these benefits:
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
THE NIAGARA DIFFERENCE: SERVICE THAT SHINES
PHONE TECH SUPPORT
Niagara technicians are available any time to
discuss the particulars of your floor and finishing
requirements. There is no challenge that we
haven’t encountered or know how to manage.
FEET ON THE STREET
We offer on-site consultation for challenging jobs
beyond the scope of routine finishing. Trust our
regional technicians for incredible support at your
job site.
SAME DAY SHIPPING
Orders are shipped on the day they are placed,
assuring quick turnaround. Express shipping is
also available to help you finish your project as
efficiently as possible.
RENTAL FLEET
All of the concrete polishing equipment that
Niagara Machine handles is available for rent as
well as for sale. Rental equipment can be shipped
to any job site via common carrier.
LARGE INVENTORY
Niagara carries comprehensive lines of equipment
and parts at all three of its location, including
the brands that set the standards for quality in
concrete floor finishing. Our mission is to serve
as a one-stop shop for optimal convenience and
TRAINING AND CERTIFICATION
Niagara offers seminars and hands-on training
in equipment selection, operation and finishing
processing for customers and maintenance
personnel.
EQUIPMENT REPAIRS
Knowledgeable, factory-trained technicians offer
complete repair and renovation services at all
Niagara locations. And our service experts can be
reached by phone for immediate trouble-shooting
consultations.
24/7 SHOPPING
Equipment and supplies can be ordered on-line
every day, around the clock to ensure the quickest
possible delivery and minimize downtime.
CUSTOMER SERVICE
Have a question? Need to place an order? Call
our friendly and knowledgeable in-house customer
support team.
Lavina® grinders/polishers incorporate an array
of innovations that ensure ease of operation,
outstanding maneuverability, dependable per-
formance and superb productivity that have
earned the brand a respected place in con-
crete construction. The company’s renowned X
Series sets the standard for concrete grinding
and polishing for the outstanding design break-
throughs it offers, including:
Forced, belt-driven planetary movement. If an
upper belt breaks it can simply be removed
and work can be continued.
U-joint floating head technology. An additional
axis enables the entire base to “float” in any
direction over the floor for optimal polishing
flexibility.
QuickChange tooling. Tools can be mounted
directly to the head with no additional plates
required. (Velcro heads required for Velcro
tooling). A locking security plate prevents tools
from disengaging.
Clog-free spraying systems. Nozzle-less water
spraying system with integral pump and filter
enables the operator to select internal spraying
beneath the machine, or spraying directly in
front of the machine in the grinding path. An
indicator light notifies the operator when the
pump is on.
Lavina X Series machines also feature upgrad-
ed forced planetary drive system and inspec-
tions cover, handles, wheels, and seals. Quality
manufacturing and continuing design improve-
ments ensure customers superior grinding
and polishing performance with Lavina. Lavina
electric and propane-driven concrete grinding
machines are manufactured by Superabrasive,
and distributed in the U.S. by Niagara Machine.
LAVINA X
SERIES
Lavina® Concrete Grinding and Polishing
Machines by Superabrasive
Lavina machines are well known for their
ease of use, durability and versatility but
with efciency at top priority, the new X
series are designed to minimize machine
maintenance and increase your productivity.
All models 25-inch and up feature a new win-
dow on the base for a quick and easy access
to the planetary drive system
Push down the pin, for the swivel handle to
swing out with ease.
New handle lock technology for tight and
secure handle adjustment.
Metered water ow for more efcient grinding
and polishing.
With the improved planetary drive system, all
L32-X models can be used for grinding with
either 3 or 6 heads.
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
L-7-X
With a 7” grinding path that easily accommodates edges and corners, the Lavina® 7-X Edger is ideal for
residential and small commercial jobs. The L-7-X features QuickChange tooling system, which includes a
new holding plate for more efcient access to the main belt and easier maintenance. This model weighs
only 137 pounds to ensure easy transportation and maneuverability.
L-13-X
This Lavina® model combines incredible innovation with outstanding ease of use. Driven by a 5.5HP,
single-phase 220V motor, the 13-X features grinding heads that can be set to the right or left, and can be
adjusted to blend edge work and eliminate path lines. A built-in level ensures an even grinding path during
operation. Lightweight design facilitates transport and operation.
L-25G-X
Entirely redesigned chain driven planetary system for increasing the ease of maintenance. The oating
head accommodates QuickChange tooling, and foam plates are the only required attachment. This grinder
also offers the clog-free spray system with optional internal or front spraying, U-joint technology for free
oating in any direction.
L-30G-X
This cordless wet/dry grinder and polisher is suited for an array of oor nishes and hardnesses. The Lavi-
na 30G-X is a propane driven planetary grinder that has an entirely new redesigned chain driven planetary
system for increasing the ease of maintenance. Easy access on top and bottom for quick access to the
mechanics of the machine. New 13.2” QuickChange tool holding plate, along with new efcient access
to the main belt allowing easier maintenance and cleaning. The 30G-X has a more durable frame with a
locking system on the base and a low prole skirt/base for reaching under cabinets and shelving. Ideal for
retail stores and warehouses.
L-38GR-X
The L38GR-X is Lavina’s heaviest and most powerful machine on the market. Featuring a 25 hp motor,
built in weights for an adjustable grinding pressure up to 790 lbs, three 13.2-inch heads and forced plane-
tary movement. The new updated double chain planetary system is designed to provide more durable plan-
etary rotation, increasing both efciency and productivity, at the same time providing easy maintenance.
L38GR-X is a remote model, operator no longer has to stand behind to grind and polish.
PROPANE L-25G-X L-30G-X L-38GR-X
Propane Engine Capacity 36.8 CU IN 36.8 CU IN 61.0 CU IN
Engine Kawasaki FS481V Kawasaki FS481V Kawasaki FX921V
Power 18 HP/3600Min 18 HP/3600Min 18 HP/3600Min
Machine Weight 590 LB 610 LB 1346 LB
Grinding Pressure 350 LB 375 LB 590/733/790 LB
Additional Weight UP TO 128 lb UP TO 128 LB BUILT IN
# Of Additional Weight 2 x 64 LB 2 x 64 LB N/A
Tool Holder RPM 570-1030 RPM 570-1030 RPM 416-750 RPM
Engine RPM 2000-3600 RPM 2000-36-- RPM 2000-3600 RPM
Working Width 25 IN 30 IN 38 IN
Application WET OR DRY WET OR DRY WET OR DRY
Dust-vacuum YES YES YES
Water Feeding INSIDE/FRONT INSIDE/FRONT INSIDE/FRONT
Dimensions L x W x H 76” x 27” x 47” 76” X 32” X 58” 110” x 39” x 53”
ELECTRIC L-7-X L-13-X
Horsepower 2HP/1.5KW 5.5HP/4KW
Voltage 1ph x 110-120V 1PH X 208-240V
Amperage 15 Amp 16 AMP
Dedicated Breaker 15 Amp 20 AMP
Gerneator Rec. 4.5KW 9 KW
Machine Wheight 137 LB 236 LB
Grinding Pressure 50 LB 57 LB
Additional Wheight UP TO 22 LB UP T0 22 LB
# of Additional Wht. 4 x 5.5 LB 4 X 5.5 LB
Working Width 7 IN 13.2 IN
Application Dry WET OR DRY
Dust-vacuum Yes YES
Water feeding No OPTIONAL
Dimensions L x W x H 31IN x 16 IN x 44 IN 47.6” X 23.6” X 36.1”
L-7-X
L-13-X
L-25G-X
L-30G-X
L-38GR-X
ELECTRIC EDGERS
PROPANE GRINDERS AND POLISHERS
20N-X Electric
The 20N-X is a lightweight concrete grinder/polisher with powerful 7.5HP motor that delivers 380 lbs. of
grinding pressure, ideal for small projects. This model can be used in wet or dry applications, eliminating
the need for multiple machines. The unique nozzle-less, anti-clogging spray system enables the operator to
continue working without the downtime required for nozzle cleaning. It also features new larger pneumatic
wheels with gray rubber to eliminate tire marks and an upgraded timing belt for more efficient maintenance.
21-X Electric
The Lavina® 21-X is a 21”, forced planetary grinder ideally suited for small projects and for rental applica-
tions. The non-clogging water delivery system ensures optimal uptime and can be adjusted for internal or
front spraying. This model also features an upgraded belt tensioner, inspection cover, belt replacement tool,
with QuickChange tools and U-joint floating head technology.
25-X Electric
The 25-X features a 10HP motor and grinding pressure of 555 lbs. to handle a variety of wet or dry prep-
ping, polishing and floor maintenance projects. The floating head is compatible with QuickChange tools and
also features security plate lock to keep tools from disengaging the head. U-joint floating head technology
and along with a chain driven planetary system makes this grinder perfect for medium to large jobs.
25L-X Electric (Also available: 25L-X-HV)
Forced, belt-driven feature enables the 25L-X to continue operating even if the drum belt breaks. A security
plate lock keeps disengaged heads from ejecting from the machine. The nozzle-less, clog-free spray system
allows the you to choose either internal or front spraying. QuickChange tools minimize tool replacement
downtime. Now with a chain driven planetary system. A removable power cable facilitates cleanup.
32-X-HV (Also available: 32-X)
The 32-X-HV has a 20HP/15KW motor that can deliver more than 800 lbs. of grinding pressure in a 32”
working width. The model is ideal for large retail stores and warehouse applications, and can be used for
grinding, polishing and floor maintenance. It has the new double-chain driven planetary system for more
durable planetary roation and two timing belts allowing more aggressive grinding with 3 heads and faster
polishing with 6 heads. The 32-X-HV features Lavina’s non-clogging spray system, U-joint floating head
technology, security plate lock, and pump indicator light.
L-32M-X-HV
The 32M-X is one of the heaviest and most powerful grinding and polishing machines, featuring six 9-inch
heads and forced planetary movement. This model is a ‘high voltage Self-propelled Grinder. Being a self
propelled unit the 32M-X allows operators to set multiple grinders to the same feed rate and speed/rpms for
a consistent pattern. The operator needs to just glide the machine in the right direction with almost no effort.
L-32-X
ELECTRIC GRINDERS
L-20N-X
L-25-X
L-21-X
L-25L-X
L-32M-X
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
QUICKCHANGE TOOLING SYSTEM
Lavina’s new QuickChange “X” tooling features
replaceable trapezoid-style pads that easily slide in
and out of a reusable plate, with no bolts required.
These tools mount directly to the heads of Lavina
grinders, and no special plates are needed. Foam
plates are still required for attaching Velcro-backed
tooling on all models.
Lavina recommends the rectangular bar/segment
tools when a more aggressive cut is required,
and when removing non-cementitious coatings.
Round button tools are recommended for removing
cementitious coatings.
Single button/segment tools are suitable for light
machines, such as 7”, 13”, 20” and 21”. For heavier
machines, such as a 25” and up, double button/
segment tools should be used. For very aggressive
grinding applications, the single rectangular seg-
ment tools should be used on all machines during
the first grinding step.
The new QuickChange “X” tooling design featured
here fits all Lavina models. The previous design of
QC tools will no longer be made.
ELECTRIC L-20N-X L-21-X L-25-X L-25L-X L-32X L-32M-X-HV
Horsepower 7.5 HP/5.5KW 2.45 hp/1.8 kw 10 HP 15 HP/11 KW 20 HP/15 KW 25 HP/18.5 KW
Voltage 1 or 3PH x 200-240V 1 ph x 100-115v 1 or 3 PH x 200-240V 3 PH x 200-240V 3 PH x 200-240 V 3 PH x 380-460V
Amperage 30 AMP 16 AMP 30 AMP 45 AMP 60 AMP 35 AMP
Dedicated Breaker 30 AMP 20 AMP 30 AMP 45 AMP 60 AMP 45 AMP
Gerneator Rec. 16.5 KW 7.5 KW 22.5 KW 33 KW 45 KW 45 KW
Machine Wheight 380 LB 219 LB 555 LB 660 LB 963 LB 1245 LB
Grinding Pressure 200 LB 113 LB 310 LB 404 LB 692 LB 715 LB
Additional Wheight up to 96 LB up to 74 lb up to 128 LB up to 128 LB up to 128 LB up to 256 LB
# of Additional Wht. 2 X 48 LB 4 x 18.5 LB 2 x 64 LB 2 x 64 LB 2 x 64 LB 4 x 64 LB
Working Width 20 IN 20 IN 25 IN 25 IN 32IN 32 IN
Application WET OR DRY WET OR DRY WET OR DRY WET OR DRY WET OR DRY WET OR DRY
Dust-vacuum YES YES YES YES YES YES
Water feeding INSIDE/FRONT PERIPHERAL INSIDE/FRONT INSIDE/FRONT INSIDE/FRONT INSIDE/FRONT
Dimensions L x W x H 53” x 21” x 43” 59.1” x 21.3” x 42” 76” x 27.2 “ x 46” 74” x 27” x 46” 92” x 34” x 44” 96” x 34” x 51”
SOFT CONCRETE - YELLOW BOND
For concrete with a PSI under 2500
X1B-SC
QC single button for soft concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X2B-SC
QC two button for soft concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X1S-SC
QC single segment tool for soft concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X2S-SC
QC two segment tool for soft concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
MEDIUM CONCRETE - GRAY BOND
For concrete with a PSI between 2500 and 4000
X1B-MC
QC single button for medium concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X2B-MC
QC two button for medium concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X1S-MC
QC single segment tool medium concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
X2S-MC
QC two segment tool medium concrete
10mm thickness
Grits: 6, 14, 30, 50, 70, 120
HARD CONCRETE - RED BOND
For concrete with a PSI between 4000 and 5500
X1B-HC
QC single button for hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X2B-HC
QC two button for hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X1S-HC
QC single segment for hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X2S-HC
QC two segment tool for hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X-HARD CONCRETE - GOLD BOND
Concrete with a PSI greater than 5500
X1B-HCG
QC single button for X-hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X2B-HCG
QC two button for X-hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X1S-HCG
QC single segment for X-hard concrete
10mm thickness
Grits: 30, 50, 70, 120
X2S-HCG
QC two segment for X-hard concrete
10mm thickness
Grits: 30, 50, 70, 120
TRAPEZOID PADS WITH PCD SEGMENTS
X-PCD
QC Trapezoid pad with 2 PCD
segments, standard
X-PCD-L
QC Trapezoid pad with 2 PCD
segments, designed for left hand
rotation
X-PCD-SB
QC Trapezoid pad with 2 PCD seg-
ments and 2 sacrificial bars
X-PCD-SB-L
QC Trapezoid pad with 2 PCD
segments and 2 sacrifical bars, left
rotation
Trapezoid pads with PCD segments and sacrifi-
cial bars are an excellent solution for thin coating
removal.
Trapezoid pads with PCD segments are a very
effective tool for aggressive stock and coating
removal. They may also be used to prepare a floor
for epoxy application.
Superabrazive brazed pads for lippage removal are
recomended for lippage grinding, floor leveling, as
well as thin coating removal. They perform excel-
lently on conrete, natural, and engineered stones.
They are designed for wet applications only.
CEM3-BR
Vacuum brazed pad
Size: 3”/80 mm
Grits: 30, 50, 100, 200
CEM4-BR
Vacuum brazed pad
Size: 4”/98.4 mm
Grits: 30, 50, 100, 200
BRAZED PADS FOR LIPPAGE REMOVAL
Waffel polishing pads are available in two conve-
nient sizes and styles, for wet and dry applications.
“Easy change” style simplifies tooling changes ad
saves time
May be used for both wet and dry applications
The seven inch variety features a double segment-
ed resin ring (two rows) for use on the Lavina 7
and Lavina 16 models.
9 inch Waffels feature a triple segmented resin ring
(three rows) for use under larger, heavy machines.
such as Lavina 25 and 32 inch models. Also avail-
able in 10.75”.
WAFF-7 (DRY & WET)
Size: 7”/175mm, 6mm thickness
Grits: 30, 50, 100, 200, 400, 600, 800, 1500, 3000
WAFF-9 (WET ONLY)
Size: 9”/232mm, 10mm thickness
Grits: 30, 50, 100, 200, 400, 600, 800, 1500, 3500
WAFF-7 (DRY ONLY)
Size: 9”/226mm, 3.5mm thickness
Grits: 30, 50, 100, 200, 400, 600, 800, 1500, 3500
NATO POLISHING DISCS
NS-D NS-4 (4” disc)
Size: 3”/81.5mm or 4”/101.6mm
Thickness: 12mm (economy- 6mm)
Grits: 30, 50, 100, 200, 400, 600, 800, 1500, 3000
NATO polishing discs have wide channels and a
unique design allowing for work on a cleaner sur-
face, ensuring a quality polish. NATOs are appro-
priate for concrete grinding/honing/polishing, and
feature a thick 12mm layer of resin and diamonds
for extra long life. Also available in a thinner “econ-
omy” style 6mm. 3 discs per head is recommended
for optimum performance.
NS
Size: 3”/81.5mm
Thickness: 12mm (economy- 6mm)
Grits: 30, 50, 100, 200, 400, 600, 800, 1500, 3000
SA HP DISCS FOR CONCRETE POLISHING
SA3 HP Superthick Discs are for dry applications
only and they are 3 inches in diameter, and velcro
backed. they are extremely durable and can with-
stand the weight of heavy machines, 1000 lbs. plus.
SA3-HP65 SUPERTHICK DISCS
Designed for softer concrete and more porous floors.
Size: 3”/80mm
Thickness: 4.5mm
Grit: 50, 100, 200, 400, 800,
1500, 3000
SA3-HP SUPERTHICK DISCS
Designed exclusively for hard concrete applications.
Size: 3”/80mm
Thickness: 4.5mm
Grit: 50, 100, 200, 400, 800, 1
500, 3000
CALIBRA GRINDING DISCS
Calibra Grinding discs are designed for the removal
of difficult scratches which are left behind by the
metal bond grinding steps. They are also useful for
floor restoration, and can be used wet or dry. These
discs are best for hard concrete applications, as
the life of Calibra is shorter when used on soft or
abrasive floors.
CA3
Size: 3”/76mm
Thickness: 10mm
Grit: 30, 50, 100, 200
CEMENTINA METAL DISCS
METAL AND COPPER RINGS
Metal and copper rings are an aggressive solution
for removing stock and deep scratches in stone
surfaces. They are designed for work on all natural
stone surfaces indlucing granite, marble travertine,
and others. We do not recommend these rings for
work on concrete or engineered stone.
SAMBR
Size: 3”/80mm or 4”/102mm
Thickness: 6mm
Grit: 46, 70, 120
HEAVY DUTY RESIN PADS
Heavy duty resin pads feature a special hybrid
metal-resin formula and new matrix, designed to
withstand the weight of heavy machines, and pro-
vide great performance and durability. They can be
used wet or dry.
HD-3 (3”/77mm) HD-4 (4”/101.6mm)
Thickness: 8mm
Grits: 30, 50, 100, 200, 400, 800, 1500, 3000
CORNERPRO POLISHING SYSTEM
The CornerPro is designed to perfect the inside of
difficult 90 degree corners and areaas where other
tooling cannot reach. CornerPro pads feature a
special trianglular shape for reaching the furthest
depths of corners and edges. CornerPro comes in
brazed, resin and electroplated bonds.
3ANG-BR
Brazed Bond 46 grit
3ANG-EL
Electroplated Bond 50, 120, 220, 400, 600 grit
3ANG-ES
Resin Bond 400, 600, 800, 1800 grit
SA SUPERTHICK DISCS
SA Superthick discs in metal bond are the ideal
choice for grinding concrete, stone, self-leveling and
terrazo floors. Available in 3 and 4 inch sizes, the
SA-MB discs provide a great first cut with a smooth
scratch pattern for an even floor finish. Offered in
two styles - with velcro backing for wet use only
and with QuckChange attachment suitable for both
dry and wet applications. They are also available
in a special Terrazzo bond, designed for softer con-
crete, and in copper bond for stone floors.
SA-TR (Terrazo bond)
Size: 3”/80mm or 4”/102mm
Thickness: 4mm
Grit: 30
SA-MB
Size: 3”/80mm or 4”/102mm
Thickness: 4mm
Grit: 47,70,120, 220, 400
SA-CO
Size: 3”/80mm or 4”/102mm
Thickness: 4mm
Grit: 46, 70, 120
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
WAFFEL POLISHING PADS
Cementina grinding discs are best suited for light-
weight machines with a relative grinding pressure of
2 to 6 lbs per square inch. Cementina achieves a
very smooth and uniform finish, preparing the floor
for resin polishing steps. Wet application only.
CEMT (Terrazo bond, soft
concrete)
Size: 3”/76mm
Thickness: 5mm
Grit: 30, 70
CEMM (Metal bond, hard &
medium concrete)
Size: 3”/76mm
Thickness: 5mm
Grit: 30, 70, 120, 220
V-HARR Premium Polishing Pads are very versa-
tile Originally designed for mechanically polishing
and restoring concrete. V-HARR is also ideal for
terrazzo and hard stone floors, and can be used
under any planetary floor polisher. The high quality
felt works between the resin segments to clean the
floor as well. V-HARR’s come in a wide variety of
sizes to accommodate many applications.
VF-5 (3 rows of resin)
Size: 5”/127mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
VF-7 (2 rows of resin)
Size: 7”/175mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
VF-8 (2 rows of resin)
Size: 8”/203mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
VF-9 (3 rows of resin)
Size: 9”/225mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
VF-10.75 (3 rows of resin)
Size: 10.75”/274mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
VF-13.5 (3 rows of resin)
Size: 13.1/333mm
Grits: 50, 120, 220, 400, 600, 800, 1800,3500, 8500
TURBO CUPS & COPPER PADS
Turbo cups with threads were specifically designed
for grinding and shaping stone and concrete surfac-
es. Turbo cups are aggressive cutters at very high
speeds, on even the hardest of surfaces.
TC4-5/8
Size: 4” or 5”
Coarse, medium, fine
CW100x15-030
4” continuous rim, coarse
CW-5/8-11
4”, 5/8 11 thread, coarse
3N COPPPER PADS
3N Copper pads are an excellent solution for corner
grinding and honing.3N Copper pads may be easily
attached to any hand grinder
3N RESIN PADS
3N resin polishing pads for natural stone are a flex-
ible and durable solution for polishing marble and
granite.
3N-4 (4”) 3N-5 (5”)
Grits: 50, 120, 220, 400, 600,
800, 1500, 3500, 8500
3N HIGH PERFORMANCE PADS
3N high performance polishing pads are produced
with a revolutionary dry only high performance
bond, they achieve an exceptionally smooth and
even polish.
3N-HP-4 (4”) 3N-HP-5 (5”)
Grits: 50, 100, 220, 400, 600,
800, 1500, 3000, BUFF
7” CONTINUOUS RING
7” continuous ring for concrete is ideal for prepping
and grinding concrete edges and corners. We rec-
ommend using this continuous rim tool to remove
gauges, deep scratches, and uneven edges. Use
this tool as your first step and follow with 3N copper
or 3N HP rings.
LV-7-RING - (30 or 70 grit)
3N-7R-CO (30, 50, 70, 120,
220 grit)
3N COPPER RINGS
3N copper rings are another solution for corner and
edge work
3N-HP-7R (50, 100, 200, 400,
800, 1500, 3000, BUFF)
3N HIGH PERFORMANCE POLISHINE RINGS
3N high perfromance polishing rings are designed
to polish concrete edges and corners after they
have been honed with 3N Copper rings. For dry
applications only.
V-HARR PREMIUM POLISHING PADS
SHINEPRO MAINTENANCE PADS
ShinePro maintenance pads provide the perfect
solution for floor maintenance. These high quality
diamond impregnated pards can be used wet or
dry with swing machines, burnishers, and auto
scrubbers. They do not require wax or chemicals
and are a very environmentally friendly solution for
maitain floors. They are safe for daily use.
ShinePro Maintenance Pads aare offered in 7”, 8”,
9”, 12”, 13”, 14”, 15”, 16”, 17”, 18”, 20”, 21”, 24”,
and 27” sizes. Grits: 220, 400, 800, 1800 & BUFF
QUICK CHANGE TOOL HOLDERS
QuickChange tooling is mounted directly to the
heads/tool holders of the new X and S series
machines (no additional QC plates are needed),
wheras the older Pro and SPS series still require
additional QC metal plates. All models require
foam plates for attaching Velcro backed tooling, and
the foam plates for PRO and SPS machines are not
compatible with X and S series machines.
X SERIES Available in 7”, 9”, 13.2”
S SERIES Available in 7”, 8”, 9”, 13.5”
PRO SERIES Available in 7”
9” TOOL HOLDER
X SERIES
9” TOOL HOLDER
S SERIES
9” TOOL HOLDER
PRO SERIES
ACCESSORIES
FOAM PLATES
Used to attach Velcro backed
tooling (X, S, Pro and SPS
models. 7”, 8”, 9”, 13.2”
QC TOOL HOLDER
ADAPTER
Used for non-Lavina machines.
QC SEESAW PLATE
Used for coating removal with
S, Pro and SPS models
WEIGHTS
Additional weights from 25 lbs
to 64 lbs.
ALUMINUM LIPPAGE
HOLDER
Used to attach Velcro backed
tooling also available in
QuckChange design.
RUBBER SPACER WITH
HOOK AND LOOP
Used as a cushion between
the diamond pad and backer.
Available in 3”, 4”, 5”, 7”, 8”, 9”
3N-4-CO (4 INCH)
30, 50, 70, 120, 220 grit
3N-5-CO (5 INCH)
30, 50, 70, 120, 220 grit
9” QC METAL PLATE
Offered in 7” and 13.5”
Ermator is a leading manufacturer of HEPA vacu-
ums and air scrubbers that offer maximum safety
and protection for both people and the environ-
ment. Ermator HEPA filters are individually tested
and certified to achieve a filtration rate of 99.99
% at 0.3 microns. All Ermator products meet or
exceed environmental and safety standards.
Safety is our priority. Ermator extractor systems
are recognized throughout the concrete floor
polishing industry as proven means to eliminating
exposure to crystalline silica through the fast,
efficient recovery of concrete dust and related
hazardous materials.
Innovative designs. Ermator innovations include
the Longopac dust-free bag changing system,
Jet Pulse filter cleaning, automatic on/off trigger
with unique power outlet, and built-in HEPA filter
alarms.
Equipment benefits. Ermator extractor systems
are compatible with all diamond surface grinders,
floor sanders and scarifiers, power saws, and
drills. Ermator equipment maximizes grinder per-
formance, increases surface visibility and diamond
life, reduces dust contamination between cuts,
ensures high volume recovery without clogging or
interruption, and minimizes dust handling.
ERMATOR
VACUUMS A HEPA Extractor system to fit any grinder,
electric saw, jackhammer, or drill:
Improves surface preparation, concrete floor
grinding and polishing:
Maximizes grinder performance
Increased surface visibility during grinding or
polishing
Increased life of diamonds and other
abrasives
Less dust contamination between cuts
Saves time and money:
Fast, high volume recover of dust without
clogging and interruption
Less handling and hauling of concrete dust
Easy and efficient filter cleaning
Compatibility:
Works with all diamond surface grinders
Works with other floor machine sanders
and scarifiers
Works with hand power saws, grinders,
and drills
Drop-Down Dustless Disposal into Poly Bags
Direct disposal into a single 11 gallon plastic
recovery/disposal bag, or 70 foot Longopac. Our
unique Longopac allows disposal into approxi-
mately 25 individually sealed bags, depending on
a comfortable weight for transfer and handling.
Continuous plastic tube
is pulled downward and
divided in single bags
of any size.
Secure the plastic tube
twice with wire ties.
Cut between the ties
and dispose of the lled
bag. HEPA lters change out quickly and easily on
job site. With little to no effort!
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
DUST IS NOT JUST DUST!
Construction dust is a
unique mix of Cement,
Concrete, Plaster,
Wood, Quartz and more
It may include asbes-
tos, mineral bers,
soot, crystal bers,
granite and mold.
The smallest particles
are the biggest threat!
These tiny pieces can
penetrate into your
lungs and stay there.
Construction dust can cause cancer, reduced lung capacity, heart disease, allergies and silicosis.
Dust should be trapped in Ermator HEPA lters, Not Your Lungs!
WHAT MAKES ERMATOR HEPA EXTRACTORS SAFE AND EFFIECIENT
All Ermator HEPA extractors include three design features that promote safety while increasing productivity.
Each HEPA lter is individually tested and certi-
ed to have a minimum efciency of 99.99% at
.3 microns based on the application airow rate
of the extractor.
Unique lter cleaning system efciently purges
the pre-lter to maintain airow, without opening
the cacuum and creating a dust hazard.
TESTED AND CERTIFIED HEPA FILTERS JET PULSE
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
S-13 SINGLE-PHASE HEPA DUST EXTRACTOR
The model S13 120V single motor HEPA Dust Extractor can be connected to electrical, hand-operated
power tools to extract freshly cut, friable concrete dust. Also an effective all-around construction vacuum for
picking-up a wide range of building materials and debris.
S-26 SINGLE-PHASE HEPA DUST EXTRACTOR
A HEPA Dust Extractor not only exhausts perfectly clean air, it is far more efficient for the fast recovery of bulk
dry dust, debris and other building materials found on every Construction, Abatement and Restoration jobsite.
S-36 SINGLE-PHASE DUST EXTRACTOR
Introducing the most powerful single-phase HEPA Dust Extractor on the market today. Three large, commer-
cial-grade vacuum motors provide over 350CFM and 110-inches of waterlift, plenty of power to handle any
mid-size planetary floor grinder.
S-1400 SINGLE-PHASE DUST EXTRACTOR
The S1400 is truly unique. It is far more efficient for the fast recovery of bulk dry dust, debris and other
building materials including volatile, fine wood dust. Advanced design features include; transparent tank,
vacuum equalization system that allows the complete filling of the Longopac bag, built-in pre-separator and
built-in Manometer.
S-13
S-26
S-36
S-1400
S-SERIES DUST EXTRACTORS
Accessories and replacement parts
S-SERIES S-13 S-26 S-36 S-1400
VOLTS 120/230 120/230 110/ 230 120
CFM 129 258 285/353 138
HP 1.7 3.4 5.1 2.2
AMPS 9/4.5 19.6/9.8 14.8 13.5
WATER LIFT 100 100 100 110
WEIGHT 66LBS 103LBS 134LBS 95LBS
PRODUCT 200900058 200900059 200900057
200800027C
CODE 200900058A
200900059B
200900057A
Rubber Blade Set
S-13 1340001
S-26/S-36 1340004
S-1400 1340005
Longopac - 4 pack
All “S” Series 1376013
Conical Pre-Filter
S-13 201000016
S-26 200900050
S-36 200900051
HEPA Filter
S-13 200700070A
S-26/S-36 200700070A
S-1400 200700070A
Hose Assembly
S-13 200900281
S-26/S-36 201000061
S-1400 200800001A
MANOMETER:
Measures the negative
pressure within the tank
and alerts the operator
when the filters need
serving.
ELECTRICAL OUTLET:
30 amp outlet for grind-
er plug-in.
CENTRAL EXHAUST:
Concentrated air
exhaust may be vented
away from jobsite with
duct hose.
CONICAL PRE-FILTER:
Stays clog free; cleans
more thoroughly via jet
pulse.
S-SERIES FEATURES
T-4000 Three Phase HEPA Dust Extractor
This new Ermator model has a 230V, three-phase motor that provides 280 CFM capacity and 125” of water lift
to ensure sufficient suction power for small and mid-sized, low voltage concrete grinders, scarifiers, saws and
shot blasters. The T-4000 has a large pre-filter and individually tested and certified HEPA filters for optimal
safety. A Longopac dust-free disposal system, Jet Pulse filter cleaning, and a manometer are also features.
T-7500 Three Phase HEPA Dust Extractor
The T-7500 is a three-phase dust collector driven by a quiet, powerful turbine motor that delivers 353 CFM
airflow. This model features two HEPA filters, sock-style pre-filters that can be cleaned outside of the tank,
and a 70-foot long Longopac® dust-free disposal system. This model is easily transported for jobsites and is
compatible with an array of floor grinders.
T-8600 Three Phase HEPA Dust Extractor
The T-8600 is powered by a turbine motor and features two tested and certified oversized HEPA filters. This
model has sock-style pre-filters that provide nonstop grinding and long service lives that can be cleaned
outside the tank via Jet Pulse negative air pressure. The T-8600 is equipped with an innovative, 70-foot long,
Longopac® dust-free disposal system, and comes with a 33’ x 3” hose and complete floor tool kit.
T-8600 Propane HEPA Dust Extractor
With an 18 HP direct-driven turbine motor, this is the most powerful propane vacuum available. It has a
capacity of 410 CFM, and a 115” water lift. The T-8600 is compatible with a variety of propane grinders.
T-10000 Three Phase HEPA Dust Extractor
Used in tandem with the C5500, the 480V, Ermator T10000 is the most powerful HEPA dust extractor/
pre-separator available worldwide, exceeding requirements of the most demanding three-head grinders.
It has three tested, certified HEPA filters, and a primary, sock-style pre-filter that can be efficiently cleaned
outside the tank via Jet Pulse. A 70’ Longopac permits easy, dust free disposal into 25 individually sealed
bags. The T 10000 is supplied with a 3” 33-foot hose, floor tool kit, 25-foot hose, wand and floor tool, and
50-amp distribution box.
T-15000 Three Phase HEPA Dust Extractor
This is the most powerful 230V HEPA dust extractor on the market today. It features a pre-filter that acts as a
built-in separator providing cyclonic operation for extended service periods. The T-15000 generates enough
airflow to handle a single 4-head grinder or two 3-head grinders, and is one of few extractors that can be
paired with a large shaver. It features four HEPA filters, Jet Pulse pre-filter cleaning, a Y-connector for one
or two 3” hoses, 70’ Longopac dust-free disposal system, and a venting port to direct exhaust away from the
worksite. It comes with a 3” 33-foot hose, and single 4” to double 3” Y-connector. When used with two 3-head
grinders (up to 32” wide), a pre-separator should be connected between each grinder and the extractor.
T-18000 Three Phase HEPA Dust Extractor
The T-18000 produces sufficient airflow to handle one 4-head grinder, or two 3-head grinders. It can be also
be paired with a large shaver. Four HEPA filters ensure clean air exhaust, and the intake port connects to
a Y-connector to accept one or two 3” hoses. Features include a venting port directing exhaust away from
the worksite, a 70’ Longopac dust-free disposal system, and Jet Pulse pre-filter cleaning. It comes with a
3” 33-foot hose and a 4” to two 3” Y-connector. When used with two 3-head grinders (up to 32” wide), a
pre-separator should be connected between each grinder and the extractor.
T-4000 T-7500
T-SERIES DUST EXTRACTORS
T-8600 T-8600 P
T-10000 T-1500
T-18000
T SERIES T-4000 T-7500 T-8600 T-10000 T-15000 T-18000 T-8600
VOLTS 230 3PH 208-240 480 480 230 480 PROPANE
CFM 280 353 353 480 647 710 410
HP 5 10.4 14 13 16 18 18
AMPS 14.8 24.2 11.9 16 42 28 KAWASAKI
WATER LIFT 125 110 110 120 140 140 115
WEIGHT 185 548 548 630 905 905 530
PRODUCT 201000671 200600404A 200600404B 201300408 201300403 200700508B 200600404L
CODE
Accessories and replacement parts
Rubber Blade Set
All “T” Series 1340004
Longopac - 4 pack
All “T” Series 1376013
Filter Sock Assembly
T-7500/8600 200600596
T-10000 201300436
T-15000/18000 200700231
HEPA Filter
T-4000 200700070A
All Other “T” Series 200600595A
Hose Assembly
T-4000 201000061
All “T” Series 1225083
A-600 AIR SCRUBBER
The A-600 is a cabinet-style air scrubber offering airflow speeds of 350 and 600 CFM. Airflow is directed
upward to eliminate dust accumulation on surfaces. An integral warning light indicates when the washable
primary filter is 75% full and requires cleaning. This model has an electrical outlet that can daisy chain up to
three units on one 15-amp circuit.
A-1200 AIR SCRUBBER
The A-1200 is a lightweight air scrubber featuring a narrow profile and two locking wheels for optimal maneu-
verability and stability. This model has a unique motor/impeller that operates at two speeds, and metal-framed
HEPA filters with a steel mesh screen for maximum protection and easy cleaning. The primary filter is wash-
able, and an integral light indicates when filters need to be cleaned or replaced.
C-1300 PRE-SEPARATOR
The C-1300 pre-separator captures 90% of material before it reaches the dust collector, keeping collector
filters clean and extending the uptime of grinding operations by minimizing filter maintenance. This model
has a capacity of 8.72 gallons and features a built-in vacuum equalizer for use with a plastic bag. It comes
with an 8-foot, 2” hose assembly.
C-3000 PRE-SEPARATOR
This model is designed with a 35 liter (9.24 gallon) pre-separator with a built-in vacuum that captures 90% of
dust before it reaches the extractor filters. The results are improved efficiency, improved filter performance
and to prolonged grinding operations with minimal interruptions for filter maintenance. The C-3000 is also
equipped with the Longopac® dust-free disposal system.
C-5500 PRE-SEPARATOR
The pre-separator on this model removes 95% of the dust volume produced during extended grinding
operations before it reaches the extractor filters. The C-5500 is the largest pre-separator manufactured by
Ermator. It features a 3” inlet and the Longopac® dust-free disposal system for safe, efficient containment
and handling.
A-600
A-1200
C-1300
C-3000
C-5500
AIR SCRUBBERS & PRE-SEPERATORS
Pre-separators A-600 A-1200
WHEIGHT LBS 41 86
MOTOR HP .25 .5
AMPS 2.1 2.8
SIZE 15X17X17 16X28X32
CFM 300/600 600/1200
SECONDARY FILTER FT2 56 140
PRODUCT CODE 200900061A 200900062A
Air Scrubbers C-1300 C-3000 C-5500
WHEIGHT LBS 31 49 130
VOLUME 8.72 9.77 26.41
COLLECTION 11 GAL BAG LONGOPAC LONGOPAC
SIZE 16X19X33 25X22X58 21X28X58
PRODUCT CODE 200600756A 200500159A 200600451
Accessories and replacement parts
Hose Kit
C-1300 200700040
C-3000 200700040
C-5500 200900054
Hose End
C-1300 1340004
C-3000 201100125
C-5500 200800367
Female 3” Camlock
C-5500 200800367
Bar With Wheels
C-5500 201000063
Longopac - 4 pack
All “C” Series 1376013
S-26 VAC TRAILER
VAC TRAILERS FOR PRESEPARATORS
VAC S-26
PRESEPARATOR C1300
WEIGHT 19 LBS
DIMENSIONS 33” X 26” X 9”
PRODUCT CODE 201400599
S-36 & T-4000 VAC TRAILER
VAC S-36 T-4000
PRESEPARATOR C3000
WEIGHT 22 LBS
DIMENSIONS 33” X 26” X 9”
PRODUCT CODE 201400598
T-7500 & T-8600 VAC TRAILER
VAC T-7500 T-8600
PRESEPARATOR C5500
WEIGHT 35 LBS
DIMENSIONS 32” X 28” X 10”
PRODUCT CODE 2014005997
VAC T-10000
PRESEPARATOR C5500
WEIGHT 40 LBS
DIMENSIONS 34” X 28” X 9”
PRODUCT CODE 201300490
Pullman Ermator’s Vac Trailers save time, and labor. One person can move both a vacuum and
a preseparator simultaneously. With its unique design the preseparator hitches inline with the
vacuum so the whole unit can be easily moved through a standard door.
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
T-10000 VAC TRAILER
Lay vac trailer on oor with small
end facing vacuum. Undo velcro
straps.
Lift back end and move vac trailer
into position to hook on front of
vacuum.
Tighten Velcro straps. Unit is
installed and ready to go!
Lay unit down and leverage top.
The bottom will hold in place.
Place large wheels completely into
slots.
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
WET/DRY HEPA VACUUMS
VAC S-50
WEIGHT 55 LBS
DIMENSIONS 31” X 19” X 28”
PRODUCT CODE 200800094A
Pullman-Holt’s wet/dry HEPA vacuums are specically designed to be used with power tools.
Stricter worker and environmental regulations are requiring tradesmen who cut and grind con-
crete and masonry materials to control dust. Collection and containing dust increases worker and
power tool productivity, extends the life of the abrasives and reduces clean-up and expense.
1.7HP, 14 Gallon Wet/Dry HEPA Vacuum with dual, individually tested and
certified HEPA filters, 99.99% at 0.3 microns
The S-50 has an outlet for power tools. The vacuum will start and stop on
demand from the power tool. The 7 second delay on the vacuum shut-off
ensures that all dust is emptied from the hose. Variable speed on the vacuum
motor allows the operator to adjust the amperage and suction power according
to circuit breaker capacity. The S-50 has an automatic filter shaking system.
A sensor indicates if a filter is clogged and starts shaking the filter immediately
after the vacuum shuts off. The compact design makes it easy to transport,
carry and to store in vans and trucks.
2 HP, 10 Gallon Recovery HEPA Vacuum
Equipped with a powerful 2 horsepower motor and an extra large capacity
HEPA filter system, the model 45 offers the air flow efficiency of vacuums cost-
ing three times as much. Low noise allows for use in sound sensitive areas.
The model 45 is manufactured to the same high standards as our larger HEPA
vacuums, so it will withstand years of hard use. Available in wet/dry or dry only.
Optional “Tool Trigger” feature allowing the operator to turn the vacuum on or
off through the power tool.
Commercial grade HEPA vacuum with tool trigger
Pullman-Holt’s 102 is designed specifically to be used with power tools and
dust management. Stricter worker and environmental regulations are requiring
tradesmen who cut and grind concrete and masonry materials to control dust.
Collection and containing dust increases worker and power tool productivity,
extends life of the abrasives and reduces clean-up and expense.
S-50
45 HEPA-DRY
102 HEPA
VAC HEPA 45 DRY
WEIGHT 38 LBS
DIMENSIONS 28” X 16” X 16”
PRODUCT CODE B160414
VAC HEPA 102 DRY
WEIGHT 68 LBS
DIMENSIONS 32” X 22” X 23”
PRODUCT CODE B527038
DUST HOODS SHROUDS AND ACCESORIES FOR YOUR HAND GRINDERS
ERMATOR DUST HOODS AND SHROUDS
The Key To Dust Control
Ermators Dust Hoods and Shrouds provide
unmatched protection when it comes to Silica dust
control. OSHA requires that an employer reduce
or eliminate crystalline silica dust. The Ermator
Shrouds and Hoods capture 98% of created dust
when grinding, crack chasing, and tuck pointing,
when used in conjunction with an Ermator Vac.
These shrouds and hoods are universal and are
compatible with most hand grinder models on the
market. For Hand Grinding use a 5” or 7” Ermator
Dust Shroud and for crack chasing/tuck pointing
the Ermator 5” or 7” Dust Hood.
Installs in seconds! Easily slide the appropriate
spacer ring onto the grinder, then slide the shroud
onto the spacer. Set your height and tighten the
clamp. You’re ready to go!
Ermator Slurry Vacs
Ermator Slurry Vacs are the solution for slurry
waste collection caused by wet grinding. Light
but efficient the Ermator W70P and W2000/2
are the perfect machines for dealing with
concrete sludge, oils and cutting fluids. These
models have a combined filter/float system that
protects the vacuum motor while at the same
time providing superior suction. W2000/2 has
a pre-separator attached providing increased
filter protection and collection.
SLURRY VACUUMS
W2000/2
HP 2 2
VOLTS 120 120
AMP 9.6 9.6
CFM 118 118
VAC WATERLIFT 90 IN 90 IN
PUMP WATERLIFT 30 FT 30 FT
HOSE 1.5” X 9’ 1.5” X 9’
WEIGHT 72 LB 192 LB
DIMENSIONS 40” X 23” X 25”
25” X 23” X 40” (2)
PRODUCT CODE 201000032C 200600769A
W70P W2000/2
Flip-up section for tight
spaces and wall work.
Repalceable wear pads on
bottom to extend life and
keep suction
Swivel so hose doesn’t
kink. Vent hole for airow
adjustment.
Rubber center piece for
exibility. Heavy duty
material for long life and
durability.
Product Code: 201400584
Product Code: 201300447
Product Code: 201200010
Product Code:
5” Dust Hood 201400311
7” Dust Hood 201400312
Deluxe 7” Shroud Universal Solid 5” Hand Grinder Shroud
Universal Convertible 7” Hand Grinder Shroud
Dust Hood
Uncontrolled construction dust. Dust hood captures harmful construction dust.
Shroud used with an S-13 curbs dust.
BEFORE AFTER
W70P
Niagara Macine Inc. offers the United States’ lead-
ing designer and manufacturer of walk-behind and
riding shot blasters, floor scrapers, and industrial
dust collectors. Niagara Machine has become the
number one distributor of BlastPro Manuafacturing,
this has been made possible
by superior manufacturing.
BlastPro’s creative design innovations
reduce both maintenance costs and
downtime, while greatly increasing
productivity.
Niagara Machine offers new and refurbished
equipment and parts, as well as rental machines.
Equipment and all parts are manufactured in the
USA using the highest quality electronics, hydrau-
lics, engines, motors and wear parts. BlastPro is
continually adding new, innovative models to its
comprehensive equipment line to ensure contrac-
tors the most efficient surface preparation
process possible. Rentals are available by the
day, week or month, and machines may be
picked up at any of our locations, or delivered
directly to your job site.
Unprecedented Customer Support.
Niagara Machine has eleven sales and service
locations. These factory trained representatives
are able to assist in equipment selection, part oder-
ing and application trouble shooting. In conjunction
with BlastPro’s 24/7 customer hotline, someone is
always available to answer your questions.
Certified Training.
Niagara Machine, offers hands-on surface
preparation training at the Niagara
Charlotte, NC facility. These are
hands-on sessions taught by
experienced staff and manufac
turer’s representatives in which
customers learn to operate
BlastPro, Lavina and
Prepmaster equipment.
BLASTPRO
SHOT BLASTERS
& SCRAPERS
BlastPro® Industry Leading Shot Blasters, Floor Scrapers and Dust Collectors
BRB-2800 ride-on oor scraper easily removes
VCT during an ofce renovation project. Hydraulic
steering and a zero-turn radius enabled the highly
maneuverable BRB-2800 to be used in tight areas.
BP9-110V Walk-Behind Shot Blaster
BRB-1500
BlastPro’s BRB-1500 is a battery-powered riding oor scraper featuring zero-turn radius for high efciency.
This unit has a low, adjustable operator seat for excellent work surface visibility. The BRB-1500 removes
waterproong membranes, tile, carpet, vinyl, hardwood ooring, thin-set adhesives, rubber, elastomeric
coatings, sports ooring and pool deck coatings.
BRB-2800
This propane-driven, riding oor scraper can accommodate the most difcult applications, removing a wide
range of materials with greater speed and ease than any comparable machine on the market. Hydraulic
steering and a zero-turn radius enable the highly maneuverable BRB-2800 to be used in difcult to access
areas.
BRB-3100EV
This battery-powered riding oor scraper can operate up to 10 hours with on a single charge. A convenient
onboard charger can be plugged into any 110v outlet.
The BRB-3100EV features a zero-turning radius, compact design to t through doors, and an adjustable
blade angle. It can be used to remove a wide range of materials including VCT, wood ooring, sheet vinyl
and elastomeric coatings.
BRB-4500
With an 8,000 square feet per hour capacity, BlastPro’s BRB-4500 is one of the most effective and efcient
oor scrapers available. This propane-driven riding machine features a highly comfortable seat to reduce
operator fatigue, and hydraulic steering for precise maneuvering in tight areas. This unit is ideal for remov-
ing tile, carpet, vinyl, wood ooring, thin set, elastomeric coatings and pool deck coatings.
SRAPERS BRB-1500 BRB-2800 BRB-3100EV BRB-4500
BLADE WIDTH 6” - 18” 2” - 36” 2” - 36” 2” - 36”
TRAVEL SPEED 300 ft/min 485 ft/min up to 250 ft/min 300 ft/min
VOLTAGE 48VDC N/A 48VDC/48VAC N/A
DIMENSIONS (LXWXH) 30.25”X31.75”X52” 74”X30”X68” w/tank 66.5”X30”X53.5” 93”X36”X72” w/tank
WEIGHT 1,500 lbs 2,800 lbs 3100 lbs 4,580 lbs
FUEL BATTERY PROPANE BATTERY PROPANE
EXHAUST SYSTEM N/A Catalytic Converter N/A Catalytic Converter
LIGHTS N/A Headlights/Flashers Headlights Headlights
BRB-1500
BRB-2800
BRB-3100EV
BRB-4500
BLASTPRO SCRAPERS
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
BRB-2800
BRB-4500
BP-9-110V
This machine is an affordable, effective, walk-behind blast cleaner designed for small to medium size jobs,
and that can also be used in conjunction with larger machines to shot blast edges and hard to reach areas.
The BP-9-110V has a 4.5 HP motor, a 9” blast pattern, lightweight design and long cord for easy handling
and maneuverability.
BP-9-220V
BlastPro’s BP-9-220V is a single-phase, walk-behind blast cleaning machine for small and medium size
jobs, and may be used to complement larger machines. This portable, lightweight model is ideal for garage
oors, balconies, basements and pool decks.
BP-9-SP
The BP-9-SP is a self-propelled, 230-volt single-phase machine ideally suited for small and medium size
jobs such as basements, decks, and hospital hallways, as well as edges and difcult to access areas on
larger concrete oors. It has a travel speed of 2 to 80 feet per minute and an 8” blast pattern.
BP-10
BlastPro’s BP-10 is an electric, self-propelled unit featuring a 460V, 3-phase motor and a 10” blast pattern.
This machine is ideal for medium to large jobs such as industrial plant and warehouse oors, parking
garages, and bridge or ship decks. Coupled with a BP-5-54 Dust Collector, the BP-10 offers optimal pro-
ductivity.
BP-10 Super
This electric, self-propelled, walk-behind model operates on 208, 230 or 460V three-phase power. It travels
up to 100 feet per minute, and has a production capacity of 300 to 1,550 square feet per hour. The BP-10
Super features high quality electrical components and an advanced air wash separation system.
BP-15 Super
BlastPro’s BP-15 Super is an electric, walk-behind, self-propelled machine with all of the superior features
of the BP-10, but with a 15” blast pattern. It travels up to 100 feet per minute and has a production capacity
up to 1,950 square feet per hour.
BP-2-20
The BP-2-20 is designed for medium to large job including warehouse oors, parking garages, and bridge
or ship decks. It is an electric, self=propelled machine witha 20” blast pattern. The BP-2-20 operates on
460V, 3 phase power. Use with the BP-9-54 dust collector for industry leading productivity.
BP-9-110V
BP-9-220V
BP-9-SP
BP-10
BP-10 SUPER
BP-15 SUPER
WHEEL KIT: BTP002649
TOP LINER: BT4973070
RIGHT LINER: BT6908260
LEFT LINER: BT6908250
FRONT BRUSH: BT6908300
SIDE BRUSH: BT6903010
BP-9-110V
WHEEL KIT: BT6917480
TOP LINER: BT6986760
RIGHT LINER: BT6986750
LEFT LINER: BT6986740
FRONT BRUSH: BT9697170-B
SIDE BRUSH: BT6908301
BP-9-SP
WHEEL KIT: BT6917480
TOP LINER: BT4973070
RIGHT LINER: BT6908260
LEFT LINER: BT6908250
FRONT BRUSH: BT6908300
SIDE BRUSH: BT6908301
BP-9-220V
In addition to having in-stock wear
parts for BastPro Manufacuring’s
equiipment, Niagara offers a full
line of wear parts for competitive
machines. Most parts are available
for same, or next day shipment.
Common BlastPro Wear Parts Available For Same Day Shipping!
BLASTPRO SCRAPERS
WHEEL KIT: BT4977780
TOP LINER: BT4899460
RIGHT LINER: BT4899480
LEFT LINER: BT4899470
MAGNET SEAL: BT49900500
BT6947210
SKID SEAL: BT6826520_
BP-10 & BP-10-SUPER
Rubber
Urethane
WHEEL KIT: BT6774960
TOP LINER: BT4990910
RIGHT LINER: BT4899480
LEFT LINER: BT4899470
MAGNET SEAL: BT4991020
BT6984390
SKID SEAL: BT6826520_
BP-15-SUPER
Rubber
Urethane
BP-2-20
BP-2-30
Designed for medium to large size jobs, this model features a 30” blast area for optimal production. The
drive system is an AC-inverted motor with integrated brake that enables the machine to maintain speed on
inclines and declines for precise control. Dual-shot valve control handles enable the operator to inde-
pendently control amperage on each blast wheel. Rear casters facilitate loading and transport.
BP-10-27
BlastPro’s BP-10-27 is a propane-driven, riding shot blasting machine for applications such as runways,
industrial oors, parking garages and bridge decks. Compact design enables the machine to pass through
36” doorways. This model features a rounded housing and innovative Hammer Head reversible, dovetail
blade that is integrated into the paddle wheel for superior performance.
BPZ-20-360
This propane-driven, riding shot blaster has an innovative zero-turn radius, and a production capacity of
3,800 square feet per hour for incredibly efcient performance. The BP-20-360 is the model of choice for
applications demanding high performance and versatility, particularly for preparing concrete for recoating
and overlays. Superior quality components ensure inherent dependability.
BP-505
This shot blaster is designed for cleaning steel and features modular construction that permits it to be
disassembled and t through a 24” manhole. Independent wheel drives optimize its maneuverability.
The BP-505 is an economical and environmentally friendly unit for cleaning and proling horizontal steel
surfaces, and facilitates the immediate application of coatings.
BP-9-54
BlastPro’s BP-9-54 is an advanced dust collection system recommended for use with the BP-10 Super and
BP-15-Super to ensure worker safety and a clean environment. It has a airow of 1200 CFM and features
reverse pulse lter cleaning that purges three lters every 13 seconds. A large dustbin ensures maximum
uptime with fewer breaks for emptying. Two 2” vacuum inlets can accommodate grinders, edgers and
related equipment.
BP-5-54
The BP-5-54 is a dust collector designed to work with the BP-10 shotblaster on medium to large size oors.
A 460V, three-phase, 5 HP motor drives this collector, which features a proven design ensuring highly
efcient and effective performance. BlastPro recommends the BP-5-54 for every surface preparation eet.
BLAST TRAVEL BLAST VOLTAGE DIMENSIONS WHEIGHT DISTANCE
PATTERN SPEED MOTOR L X W X H TO EDGE
BP-9-110 9” MANUAL 4.5 HP 110 V 42.5”X12.5”X39” 121 LB 1.5”
BP-9-220V 9” MANUAL 3 HP 208, 230 V 47”X12”X39” 178 LB 1.5”
BP-9-SP 8” 2-80 FT/MIN 4 HP 230 V S-PH 36”X12”X48” 318 LB 1.5”
BP-10 10” 0-100 FT/MIN 10 HP 460 V 3-PD 63”X17”X40” 730 LB 1.5
BP-10 SUPER 10” 0-100 FT/MIN 15 HP 208/230/460 S-PH 63”X17”X40” 318 LB 1.5”
BP-15 SUPER 15” 0-100 FT/MIN 20 HP 208/230/460 V 3-PH 72”X23”X41” 847 LB 2.5”
BP-2-30 30” 0-100 FT/MIN 2/20 HP 460 V 3-PH 75”X39”X48” 1,575 LB 2.5”
BP-10-27 10” 0-200 FT/MIN 27 HP PROPANE 78”X34”X57” 1,525 LB 4”
BPZ-20-360 20”
40-240 FT/MIN
4 CYL GAS OR PROPANE 108”X67”X67” 4,000 LB 6”
BP-2-20 20” 0-120 FT/MIN 2/15 HP 460V 3 PH 77”X28”X55” 1,270 LB 2.5”
BP-2-30
BP-10-27
BPZ-20-360
BP-505
BP-9-54
BP-5-54
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
STI Prep/Master® manufacturers a line of high quality
electric and propane-powered concrete grinders and
metal-bond & diamond polishing systems for applica-
tions ranging from small residential projects to large
retail buildings, parking garages, and commercial
warehouses. These grinders are designed to achieve
high quality finishes with optimal productivity.
Prep/Master® combines extensive research and
development with exhaustive product testing at actu-
al job sites to ensure unprecedented grinding &
polishing machine performance. The result is a line of
versatile, dependable machines & diamond systems
that achieve superior finishes while ensuring operator
ease, optimal portability and superior efficiency.
PREP/MASTER®
GRINDERS
IT’S A SYSTEM - NOT A MACHINE
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
800-622-2048
From Concrete Prep to Polish —
P/M Machines can tackle any sized project
on any ooring surface!
Marble Floor Restoration
using the STI MG2 Diamond System and
the P/M Machine
Restoration of a Terrazzo oor
using the STI-2807 Machine,
TPS Diamond System, and Grout Pans
Concrete Polishing at its best!
STI-3030
STI-2807
STI-2420
STI-4430
Prep/Master® STI-2807
One of Prep/Master’s® most popular models, the STI-2807 is designed for medium-sized projects under 2,000
square feet and is an ideal choice for residential contractors. Lightweight and compact design enables this
model to access tight areas, and its variable speed drive easily accommodates differing grinding conditions.
The STI-2807 can be easily loaded and unloaded by a single worker.
Prep/Master® STI-2420
This STI-2420 is an easy to operate grinder ideally suited for projects larger than 5,000 square feet. This
machine is extremely easy to operate and features a variable speed drive to accommodate diverse floor con-
ditions, with a movable weight system to adapt to different applications. The STI-2420 can be easily loaded
and unloaded by a single worker.
Prep/Master® STI-3030
The Prep/Master® STI-3030 is an ideal choice for polishing projects greater than 10,000 square feet. Despite
its weight and size, this grinder is easy to operate, and its variable speed drive easily adapts to different
grinding or polishing conditions. A movable weight system gives it the versatility for various applications.
Prep/Master® STI-4430
The Prep/Master® STI-4430 is a high capacity machine recommended for polishing projects of 20,000 square
feet and greater. It can be quickly disassembled to pass through 36” doorways, and is easy to operate. It
features movable weights, variable speed drive, and is easy to load and transport.
Prep/Master® GRINDERS
ELECTRIC STI-2807 STI-2420 STI-3030 STI-4430
Motor 7.5HP - 3PH 20HP - 3PH 30 HP - 3 PH 30 HP - 3 PH
Power Source 220/230 VAC 220/230 VAC 220/230 VAC 220/230 VAC
1 or 3 PH 60 Hz 1 or 3 PH 60 Hz 1 or 3 PH 60 Hz 1 or 3 PH 60 Hz
Power Cord 25 FT 25 FT 25 FT 25 FT
Vac Hose Connection 3 IN x 25 FT X2 3 IN x 25 FT X2 3 IN x 25 FT X2 3 IN x 25 FT X2
Weight 733 LB 978 LB 1,320 LB 1,460 LB
Tool RPM 300-750 RPM Variable 250-750 RPM 300-750 RPM Variable 250 - 750 RPM
Number of Tools 6 12 12 24
Tool Style EG Attachment System EG Attachment System EG Attachment System EG Attachment System
Dimensions L x W x H 72” x 28” x 50” 75” x 27” x 50” 86” x 30” x 52” 80” x 44” x 52”
STI EDGE PLATE
Holds all STI tooling & diamonds. Cuts within 1/2
inch from edge. Covers more SF/M2 than STI’s pre-
vious tool plate. Eliminates the need for hand-grind-
ing to finish edges!
Fits our most popular Prep/Master® models: 2807
& 3030. Use 7-3/8” x 1” Adapter with edge plate for
STI-3030 to clear gear box lip.
880000502
Size 502 - Standard Flex
880000602
Size 602 - Standard Flex
880000702
Size 702 - Rigid for Flattest Cut
STI TOOL HOLDERS
885002807 fits STI-2807
885003030 fits STI-3030
885000738 adapter for STI-3030 EG ADAPTER PLATE - “QUICK CHANGE”
Attaches to modified STI tool plate for after market
assembly. Designed for use with the EG Metal
Bond Diamond and EG Adapter-Velcro. Mounts
using 2 bolts included.
570000014
MORFLEX COUPLER
Provides flexibility for the tools to follow the contour
of the floor. Good replacement part to have on
hand for less downtime. Three styles available.
ALUMINUM MILLED HOLDER
Aluminum backer with
machined 5/8”-11 arbor
803000001 - 3 inch
804000001 - 4 inch
E/Z BACKERS
Bolts to E/Z plug holder. Velcro backing securely
holds diamond pads in place. Velcro backing allows
for fast and easy diamond pad replacement.
RUBBER HOLDER
Rubber backer with 5/8”-11 arbor
803000003 - 3 inch
804000003 - 4 inch
BAKLITE HOLDER
Hot-pressed rigid baklite with
5/8”-11 arbor
803000002 - 3 inch
804000002 - 4 inch
STI-2818LP
STI-2418LP
STI-3038LP
STI-4438LP
Prep/Master® STI-2818LP
The model 2818LP has an 18HP propane-powered motor that eliminates the need for transporting a genera-
tor to the job site. With a small footprint and lightweight, this grinder is ideal for difficult to access areas, and
also make it easy to load and unload. This model is recommended for projects less than 2,000 square feet.
Prep/Master® STI-2418LP
The STI-2418LP is a medium-capacity grinder designed for projects greater than 5,000 square feet. It com-
bines the production capacity of a larger machine with the maneuverability of a smaller grinder. The STI-
2418LP is powered by an 18HP Kawasaki propane motor.
Prep/Master® STI-3038LP
The STI-3038LP has the same robust design as the model STI-3030, but is powered by a 38HP Kawasaki
propane motor. It features a movable weight system for multiple applications, and is recommended for proj-
ects greater than 10,000 square feet.
Prep/Master® STI-4438LP
This model is the propane driven version of the high capacity STI-4430, but without the added weight of the
electric motor. It is driven by a 38HP Kawasaki propane engine and has a polishing capacity of 20,000 square
feet per hour. The STI-4438LP can be loaded and unloaded by a single worker.
PROPANE STI-2818LP STI-2418LP STI-3038LP STI-4438LP
Motor Kawasaki 18HP LP Kawasaki 18HP LP Kawasaki 38HP LP Kawasaki 38HP LP
Motor RPM 2,200-3,650 RPM 2,200-3,650 RPM 2,200-3,650 RPM 2,200-3,650 RPM
Vac Hose Connection 3 IN x 25 FT 3 IN x 25 FT 3 IN x 25 FT 3 IN x 25 FT
Weight 829 LB 895 LB 1,084 LB 1,315 LB
Tool RPM 366-500 RPM 366-500 RPM 366-500 RPM 366-500 RPM
Number of Tools 6 12 12 24
Tool Style
EG Attachment System EG Attachment System EG Attachment System
EG Attachment System
Dimensions L x W x H 73” x 30” x 50” 78” x 27” x 48” 86” x 30” x 48” 78” x 44” x 50”
Prep/Master® Propane GRINDERS
STI BURNISHERGROUT PANSCONCRETE PREP TOOLS
#00 PCD EG PREP TOOL
Super Fast Removal with Rough Profile
Fast cutting, aggressive metal bond tools used to
remove black mastic, epoxy, adhesive, and thin-
set. NOT recommended when polishing is to be
provided - leaves a rough profile.
#0 PREP TOOL
Productive Removal with Smooth Profile
Productive metal bond tools used to remove black
mastic, epoxy, adhesive, and thin-set. Great price
with a variety of bonds for concrete condition.
Recommended when polishing is to be provided.
One set consists of 50% right-hand-
ed tools and 50% left-handed tools.
571603418 Right-hand PCD Tool
571603412 Left-hand PCD Tool
540243000 Regular Bond
571522332 Soft Bond
571522325 Hard Bond
571522326 Super Hard
EG GROUT PANS
The rotary action of the
Prep/Master® pushes the epoxy
into the pin holes from multiple
directions to push air out and ll
in the holes!
For use on concrete and terrazzo oors with the
EGT and TPS Diamond Systems.
• Fills the pin holes in terrazzo more thoroughly
than the conventional way of hand troweling
and bufng the epoxy into the holes
• Used on the Prep/Master® or any other Rotary
machine
• Velcro-backed for easy tool change
• Lasts over 10,000SF/929 M2
640900035
PMB-21
Ensures maximum speed while delivering
superior results in substrate polishing!
• A low profile deck with bumper skirting
• Lower torque
• Tilt back deck design for quick
pad changes
• Higher RPM burnishing speeds
deliver superior wet look shine
• Powerful Kawasaki 18 HP
603cc engine
• EnviroGard emissions
monitoring system and
catalytic mufflers lower CO, HC
and NOx emissions
• Standard water tank for wet
operation only
• Uses STI CASH Dots
Diamonds
Propane Version - Item #808000211
Electric Version - Item #808000210
STI DIAMOND SYSTEMS
Concrete Polishing Planetary Terrazzo Polishing Marble/Terrazzo
Restoration
540574001 EGT #1
540574002 EGT #2
540574003 EGT #3
540574004 EGT #4
540574005 EGT #5
540574006 EGT #6
540574007 EGT #7
540574008 EGT #8
527680001 PMW #1
527680002 PMW #2
527680003 PMW #3
527680004 PMW #4
527680005 PMW #5
527680006 PMW #6
527680007 PMW #7
530400001 CLC #1
530700002 CLC #2
530746003 CLC #3
530752004 CLC #4
530860005 CLC #5
530870006 CLC #6
530880007 CLC #7
585400001 PLP #1
585400002 PLP #2
585400003 PLP #3
585400004 PLP #4
585400005 PLP #5
585400006 PLP #6
585400007 PLP #7
585400008 PLP #8
585400009 PLP #9
640900001 TPS #1
640900002 TPS #2
640900003 TPS #3
640900004 TPS #4
640900005 TPS #5
640900006 TPS #6
640900007 TPS #7
21-inch Pads
390210001 MG2 #1
390210002 MG2 #2
390210003 MG2 #3
390210004 MG2 #4
390210005 MG2 #5
390210006 MG2 #6
390210007 MG2 #7
390210008 MG2 #8A
390000002 MG2 #8B
17-inch Pads
390170001 MG2 #1
390170002 MG2 #2
390170003 MG2 #3
390170004 MG2 #4
390170005 MG2 #5
390170006 MG2 #6
390170007 MG2 #7
390170008 MG2 #8A
390000002 MG2 #8B
All EG tools on this page are built with the patented EG
Quick Change System (Patent 8,192,255).
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8A
STI Diamond Systems are coordinated metal and resin bonded diamond systems that polish and/or restore
concrete, terrazzo, marble, or granite flooring using any of the eight models of Prep/Master® machines.
Each system is only to be used in correct numbered order in order to achieve best results. All tools are
color-coded to indicate a matched system.
METABO GRINDER & POLISHER KITS
SMITH SHAVERS
FS200™ combination scarifier/grinder with feath-
ering wheel is the perfect for users looking for a
simple all-in-one lightweight, portable solution to
remove coatings, surfce-prep and lightly scarify
any floor surface with a variety of optional cutter
drums to produce SP3 - SP9 surface profiles.
U. S. SAWS DUST BUGGY
Electric Dust Buggy - Joint Cleanout Saw
Portable, adjustable, lightweight joint cleanout saw
perfect for indoor joint work. Its up-cut blade rota-
tion allows debris to be removed from joints.
Transform Your Standard Angle Grinder/Polisher
Into An Effective Planer!
The Scoot is a simple and easy to use device
that will transform your standard angle grinder or
polisher into an effective planer! It is universal,
is available in three sizes and is compatible with
every grinder.
DIAMAPRO SPEEDI EDGE DIAMAPRO EZ KNEEL
As you use the DiamPro EZ Kneel, you will find
that by being supported in a kneeling position and
by only having to swivel your knees to move you
will eliminate that normal wear and tear that abus-
es your body. Both the seat and chest support
different angles, different heights, and slide on
a rail front to back. This allows you to use both
hands in different working positions while your
back and knees are fully supported, and you can
control your movement with your feet and toes.
The support is a comfortable dual density foam
which connects and disconnects quickly.
DIAMAPRO DEMON SWING MACHINE
The Demon is a low speed buffer ergonomically
designed to be easy to hold onto, back wheels
allow the operator to move in a forward to back
motion rather than a side to side swing motion.
The DiamaPro Demon has many uses and can
accept a variety of tooling to assist in prepping,
sanding, and polishing a variety of concrete and
stone surfaces.
The FS300D™ is the professional’s reliable, every-
day, cost-effective heavy-duty walk-behind surface
preparation choice. The only scarifier that removes
up to 15” wide with high-precision cutting action –
while delivering more scarifying power – resulting
in twice the production of the competition.
Redesigned all-steel chassis with flexibility for use
alone or with your equipment, lockable depth-con-
trol settings for consistent removal in the “impact
zone,” up to 2x faster removal speeds with adapt-
able changes for diamond shaving, rotoplaning
or carbide scarifying, re-designed vacuum pickup
location to contain debris. Lower vibration and
extended bearing life, new lifting carriage with
height-adjustment lever, fewer moving parts to
increase uptime
FS200
FS300D
Electric, Gas or
Propane Models
FS351
Electric, Gas, or
Propane Models
Electric
7” Surface Prep Kit
Includes a Metabo
W24-230 Grinder,
Dust Shroud and
D-ring handle.
Metabo Polisher Kit
Includes a Metabo
PE12-175 Variable
Speed Polisher,
5” Backer pad and
dust shroud.
5” Surface Prep Kit
Includes a Metabo
WE15-125 HD GED
Grinder, Dust Shroud
and carrying case.
Tuck Point/Crack
Chaser Kit - Includes
a 5” Metabo W9-125
Grinder, Dust hood
METABO KITS WITH SPEEDI EDGE PACKAGE
7” Surface Prep Kit with
a DiamaPro Speedi Edge
Max and a Premium Dust
Shroud
Metabo Polisher Kit with
a DiamaPro Speedi
Edge Standard, 5” Velcro
Backer Pad and Dust
Shroud
5” Surface Prep Kit
with a DiamaPro
Speedi Edge Mini and
Dust Shroud
325 WEST FRONT ST. ERIE, PA 16507
814-455-8838
n
814-454-0160 FAX
www.niagaramachine.com
DIAMAPRO 27” BURNISHER
The newly designed and aggressively priced
DiamaPro 27” burnisher has a rugged, solid steel
body design with an ultra low 3¾” profile for buffing
and polishing under racks and hard to reach areas.
The DiamaPro 27” also includes an advanced
composite polymer pad driver and dust control
upgrade.
MEGA HIPPO MIXER
PORTAMIX MEGA HIPPO® Mixing Stations –
Mix, Transport and Pour Up to Six 50-lb. Bags in
Minutes.
Mixing multiple batches is faster and easier with
the new MEGA HIPPO liner canister system.
Cement screeds, grout, mortar, textured coatings,
sealants, adhesives and other selfleveling com-
pounds can be mixed quickly. The MEGA HIPPO
boosts productivity, lowers labor costs and reduces
physical effort.
TAYLOR WALK-BEHIND SCRAPER
464-R can tackle the hard-to-remove projects that
are beyond the capabilities of self-propelled strip-
pers that don’t have quick reverse and variable
speed controls.
The new 464-R has all the control you could ask
for at a price that is still a mere fraction of competi-
tive self-propelled machines.
DIAMAPRO WALK-BEHIND SCRUBBER
Rugged Economical, Dependable
Automatic Floor Scrubbing
Wet scrub and dry vacuum in one pass. The
brush-driven ProScrub is inexpensive to purchase
and maintain. Fast and efficient, it’s very user
friendly. 24 volt system delivers approximately 3
hours run time when fully charged. Exceptionally
simple to operate and maintain.
ELECTRIC DUAL POLYUREA GEAR PUMP
Blend and propel 2-part polymers with U.S. Saws’
Electric Dual Component Polyurea Gear Pump.
When duality is necessary to mix the different
ingredients to create the ideal polymer substance
and then apply it, use U.S. Saws pump. For a
guaranteed perfectly mixed polymer, this dual
component pump will not fail. To alternate between
1:1 and 2:1 liquid ratio the sprockets can be
changed with little effort and convenience.
A powerful 14.5 Amp motor allows mixing of up
to 200 pounds of high-viscosity materials rang-
ing from epoxy, mortars, plasters and cement to
quartz-containing resings and flooring compounds,
as well as insulation and other materials.
HAND-HELD MIXING DRILL
DIAMAPRO PERFECT LINE
One-third the cost, One-third the time
and all the precision.
One person can apply tape to mask painted safety
lines or permanent safety tape more that 3X faster
than two workers using the traditional taping meth-
od. The DiamaPro Perfect Line has adjustable
width guides allowing lines from 2 to 8 inches.
Optional 4 inch guide allows application of safety
tape. Integrated chalk line stud and pointer deliver
superior and reproducible quality.
325 West Front
Erie, PA 16507
814-455-8838
814-454-0160 fax
1803 Associates Lane
Charlotte, NC 28217
704-329-5701
704-329-5705 fax
Bloomeld Business Park
415 Bloomeld Dr.
W. Berlin, NJ 08091
856-767-1863
856-767-1746 fax
Three Service and Showroom Locations Ten Sales Locations
800-622-2048
