Guideline Geo 500MHZ Ramac GPR/500 MHz shielded antenna User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	267429
Application ID	5aP1OZGEnzntFWK7zPuyLg==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	241.34kB (3016705 bits)
Date Submitted	2002-09-03 00:00:00
Date Available	2003-01-08 00:00:00
Creation Date	2002-09-03 08:24:31
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2002-09-03 08:24:33
Document Title	users manual

MALÅ GeoScience
RAMAC X3M
and
EasyLocator
Hardware Manual
Important note:
In the US this unit operates under FCC rules Part 15. According to
these rules a GPR system shall contain a manually operated switch
that causes the transmitter to cease operation within 10 seconds
of being released by the operator.
Therefore all units sold after July 15 2002, in the US, will have this
functionality and also be delivered with a kill switch.
Units sold outside the US will have a plug attached to the kill
switch connector. Removing this plug causes the unit to cease
functioning. No kill switch will be delivered to destinations outside
US.
The kill switch and how it’s to be handled is further explained in
this manual.
Table of Contents
____________________________________________________________
1. Introduction
1.1 Unpacking and Inspection
1.2 Repacking and Shipping
2. Start up and hardware description
2.1 Layout of the X3M
2.2 Mounting on the shielded antenna
2.3 Power cable
2.4 Distance measuring devices
2.5 Connection to computer
2.6 Kill switch
2.7 Start up and power button
3. Batteries and charging
3.1 Batteries
3.2 Charging
4. Software
5. Using the RAMAC X3M
6. RAMAC X3M specifications
10
1
Introduction
___________________________________________________________
Thank you for purchasing the RAMAC X3M/EasyLocator. We at Mala
GeoScience welcome comments from you concerning the use and
experience of this equipment, as well as the contents and usefulness of this
manual. Please take the time to read through the assembling instructions
carefully and address any questions or suggestions to the following:
MALÅ GeoScience postal address is:
Main Office:
Subsidiary:
Malå GeoScience
Skolgatan 11
S-930 70 Malå
Sweden
Phone: +46 953 345 50
Fax: +46 953 345 67
Malå GeoScience USA, Inc.
P.O. Box 80430
Charleston, SC 29416
USA
Phone: +1-843 852 5021
Fax:
+1-843 769 7397
E-Mail: sales@malags.se
sales.usa@malags.se
rental@malags.se
support@malags.se
Information about MALÅ Geoscience’s products is also available on
Internet: www.malags.com
(Be sure to include instrument type and serial numbers)
1.1
Unpacking and Inspection
Great care should be taken when unpacking the equipment. Be sure to
verify the contents shown on the packing list and inspect the equipment for
any loose parts or other damage. All packing material should be preserved
in the event that any damage occurred during shipping. Any claims for
shipping damage should be filed to the carrier. Any claims for missing
equipment or parts should be filed with Mala GeoScience.
1.2
Repacking and Shipping
If original packing materials are unavailable, the equipment should be
packed with at least 80 mm of absorbing material. Do not use shredded
fibers, paper wood, or wool, as these materials tend to get compacted
during shipment and permit the instruments to move around inside the
package.
2
Start up and Hardware
Description
___________________________________________________________
The RAMAC X3M/EasyLocator is an integrated radar control unit, mounted
directly on the shielded antennas and powered externally. X3M is
compatible with the RAMAC/GPR shielded antennas 100, 250, 500 and
800MHz. EasyLocator has it own family of shielded antennas; DEEP, MID
and SHALLOW. The built-in electronic design makes it a low weight and
compact size system, easier to assemble and operate. No fiber optic cables
are required since the unit communicates directly with the laptop. Based on
the flexibility and the modularity of the RAMAC/GPR, the RAMAC X3M is
fully compatible with the Windows based acquisition software Ground
Vision, while the EsayLocator has it own acquisition software: EasyVision.
The built-in default autostacking function secures the best data quality at
maximum survey speed, in both units.
This section will give a short overview of how the GPR (Ground Penetrating
Radar) systems work.
2.1
Layout of the RAMAC X3M /EasyLocator
1. Kill switch
connection
4. Parallel
cable port
connection
2. Power button
5. Securing screws
Figure 2.1. Layout of RAMAC X3M
3. Encoder
connection
6. Power cable
connection
Figure 2.1a. Layout of the X3M
The different number in Figure 2.1 corresponds to the following:
1:
2:
3:
4:
5:
6:
Connector for kill switch
Power button
Connector for encoder, 9 pin d-sub (wheel or hip chain)
Connector for parallel cable to a PC, 25 pin d-sub
Securing screws for mounting on antennas
Power cable connection
3. Encoder
4. PC comm.
6. DC power
2. ON/OFF
Figure 2.1 b.
EasyLocator.
2.2
1. Kill switch
The same connectors as in figure 2.1a showed on an
Mounting on the shielded antennas
Start by placing the X3M/EasyLocator on the antenna that you are going to
use for your measurement. The Parallel port and the Power connection
should point forward according to the picture (Figure 2.2).
Fasten the unit on the antenna by tighten the securing screws.
Figure 2.2 Mounting on the antenna
2.3
Power cable
When the X3M/EasyLocator is mounted on the antenna connect the Power
cable from your battery.
Look for the countersink and place it
towards the mark on the connection.
Push lightly. If you have it in the correct
position it should connect smoothly.
To disconnect: Pull out, holding the milled
part of the connection.
Figure 2.3. Power cable
2.4
Distance measuring devices
The X3M/EasyLocator can be used together with
the standard
MALÅ
GeoScience
distance
measuring devices (hip-chain and measuring
wheels). The encoder cable is connected as shown
below (Figure 2.4)
Figure 2.4. Encoder
2.5
Connection to computer
Add the computer to the system by
connecting the parallel port cable between
the computer and the X3M/EasyLocator
(Figure 2.5).
Use an IEEE 1284 compatible parallel cable
that is less than or equal to three meters
long.
Figure 2.5. Parallel port
2.6
Kill switch
The kill switch is attached to a
handle that can either be
handheld or snapped onto a
RAMAC/GPR Cart (Figure 2.6
top).
The X3M/EasyLocator will not
be operational without the kill
switch. The button has to be
pushed down at all times
during measurements. If the
button is released the
transmitter will stop
transmitting.
Kill switch
Connect the kill switch to the
bayonet holder on the X3M/EasyLocator
by pushing lightly and turning the bayonet
socket clockwise (Figure 2.6 bottom).
To disconnect: Turn the bayonet socket
counterclockwise and pull out.
Figure 2.6. Kill switch
2.7
Start up and power button
To start the X3M/EasyLocator press and hold the start button for
approximately two seconds. The light in the center of the button will start to
flash (Figure 2.7).
Next start the acquisition software,
GroundVision or EasyVision, in your
computer. During the measurement the
button will have a steady light.
The X3M/EasyLocator has autostacking as
a default setting. More information about
autostacking and how to operate the
software will be found in their respective
manuals
Figure 2.7. Power
If you need to reset the X3M/EasyLocator press the power button for at
least three seconds. When the light starts to flash again the X3M is ready
for new measurements.
To turn the X3M/EasyLocator off, push the button and release quickly. The
red light will then stop flashing; the unit is now off.
If the power cable is accidentally pulled out, the X3M/EasyLocator will start
automatically when the cable is inserted again.
3
Batteries and charging
___________________________________________________________
3.1
Batteries
The battery belt is the standard power supply for the RAMAC
X3M/EasyLocator.
Capacity of the battery is 12V/9 Ah. This gives an operation time of 6-8
hours. When the battery voltage has dropped down to 10V the
X3M/EasyLocator will automatically turn itself off. The battery should always
be stored fully charged to maximize the lifetime of the battery. The
X3M/EasyLocator can also be supplied by any other external 12V DC power
source.
The EasyLocator can also be purchased with a specially designed trolley
system. This trolley has a special battery box, designed for Li-Ion batteries.
These are more lightweight while giving the same operation time.
3.2
Charging
The battery charger is an automatic quick charger designed for lead acid
batteries. The recharge up to about 80% of the full capacity goes very
quickly. However, it is recommended to keep the battery charging until it is
fully charged. The battery charger can be left on after the battery has been
fully charged. It then automatically turns into maintenance charging.
The indicator lamp on the charger gives you the following information:
Red = Charged < 80%
Yellow = Charged 80-100%
Green = Maintenance charging
Output 2.7 A, equals charging time between 3-5 hours (80%-100%)
Software
___________________________________________________________
The RAMAC X3M is designed to operate best with the data acquisition
software, GroundVision. The software is compatible with Windows 9x/ Me/
NT/ W2000 and XP. GroundVision is designed for a quick setup and storage
of default settings in the X3M. All data is stored in its original format (raw
data) on the hard drive of the computer for further post processing, if
10
required. Please refer to the GroundVision software manual for further
information on the acquisition software.
The EasyLocator is operated with the software EasyVision, designed for
optimal user friendliness. Please refer to the EasyVision software manual
for further information.
11
5
Using the RAMAC X3M/EasyLocator
___________________________________________________________
There are many applications where you can use the RAMAC
X3M/EasyLocator. A variety of different accessories that will make the
measurement easier are available for the X3M/EasyLocator.
The X3M/EasyLocator can
be used together with the
RAMAC/GPR Cart. The Cart
is designed for surveys on a
flat surface (Figure 5.1)
Figure 5.1 RAMAC X3M with 500MHz antenna
If the RAMAC/GPR Cart is
not suitable the system can
also be towed by using the
pulling handle and the X3M
PC holder. (Figure 5.2)
Figure 5.2. RAMAC/GPR Cart with X3M and 250MHz
antenna.
Note: All measurements should be performed with the antenna close to
ground, for best results.
12
6
RAMAC X3M Specifications
___________________________________________________________
Pulse repetition frequency
Data bits
Nr of samples/trace
Nr of stacks
100 kHz
16
128-8192 (1024 with autostacking)
Autostacking in the range 1-32768 for
optimized speed performance
Signal stability
< 100ps
Communication interface
IEEE 1284 (ECP)
Communication speed
>700 kb/s
Data transfer rate
40-400 kb/s at 4 Mbit/s
Acquisition mode
Distance/time/manual
Power supply
External 12V DC battery (Pb)
Operating time
6-8 hours with standard battery belt
Charger
Quick charger, automatic charge cycle 100
40VAC input
Charge time
3-5h (80-100%)
Measuring wheel
Standard RAMAC/GPR trigger device
Software
Compatible with GroundVision
Antennas
Shielded antennas 100, 250, 500 and 800 MHz.
Dimensions
310 x 180 x 30 mm (12.2 x 7 x 1.2 in)
Weight
1.7 kg (3.7 lb)
Operating temperature
-20oC to +50oC (-4oF to +122oF)
Environmental
IP 67
Notes:
EasyLocator does not have manual mode.
EasyLocator also has an Li-ion option.
EasyLocator only operates with the EasyVision software
EasyLocator is compatible with the DEEP, MID AND SHALLOW antennas.
13

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2002:09:03 08:24:31
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2002:09:03 08:24:33-04:00
Page Count                      : 13

EXIF Metadata provided by EXIF.tools