Guoguang Electric 00006 Bluetooth Car Kit User Manual bt carkit fiat UM draft v6

Download:
Mirror Download [FCC.gov]
Document ID	2272810
Application ID	0q+kX8AUpPIjOGJsBsbOHA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	74.28kB (928552 bits)
Date Submitted	2014-05-21 00:00:00
Date Available	2014-05-21 00:00:00
Creation Date	2014-05-08 15:54:33
Producing Software	Adobe PDF library 10.01
Document Lastmod	2014-05-14 09:53:38
Document Title	bt_carkit-fiat-UM-draft-v6
Document Creator	Adobe Illustrator CS6 (Macintosh)

logo
Amazon Bluetooth Car Kit
User Instruction Manual
TABLE OF CONTENTS (CONTENTS TO BE CONFIRMED.)
User Manual
1. Introduction .................................................1
2. Setup ........................................................... 2
Initial Setup ......................................................... 2
Connectivity ........................................................ 4
Playing Music / Call Operation ............................ 6
4. Troubleshooting ........................................... x
5. Safety Warning ............................................ x
6. Information ................................................10
INTRODUCTION
User Manual
Introduction
Thank you for purchasing Amazon Bluetooth Car
Kit. (CONTENTS TO BE CONFIRMED.)
What’s in the box
Bluetooth Receiver 3.5mm audio Power plug 3.5mm audio
extension
(insert into the
& Mounting Disc signal output cigarette
lighter)
cable
SETUP
User Manual
INITIAL SETUP
Connect to power and AUX:
1. Insert the cigarette plug & ignition, the plug
power up and showed the green LED.
2. Plug in the 3.5mm plug into car's Aux In
3. Make sure your car stereo is On and set the
input source to AUX In
Decide the Bluetooth receiver location:
•
The Bluetooth receiver can place on the car
dashboard that in front of the driver or next to
the driver area.
SETUP
•
•
•
User Manual
The microphone is built in the Bluetooth
receiver. So, it is recommend to locate the
Bluetooth receiver as close as your
convenience.
Locate the Bluetooth receiver in a smooth
and flat surface.
Make sure the surface is dry and free of dirt.
Located the Bluetooth receiver
•
•
•
After decide the Bluetooth receiver location,
we need to set up the mounting disc to hold
the Bluetooth receiver
Peel off the back adhesive of the mounting
disc and stick it on the
decided Bluetooth
receiver location
The Bluetooth receiver
will magnetically attach
to the mounting disc.
SETUP
User Manual
TURN ON AND PAIRING
1. Press the Multi-function key once to turn on
the Bluetooth receiver, the Red and Blue LED
will turn on 1 second in the same time, then
it will turn to solid Red and a notable tone.
The receiver will be connect to last device
when powered on.
2. When the receiver power on, press and hold
the multi-function key around 5 seconds to
enter the pairing mode and a notable tone.
3. The Red LED will blink slowly as it is in the
pairing mode.
4. Turn On your BT device and scan, select
“Amazon_BTC1” to connect.
5. The Red LED will stop to blink and the LED
color will change to solid Blue with beep tone
after paired.
6. Then, you can press multi-function key once
to play music in the car audio system from
your Bluetooth device.
SETUP
User Manual
7. If you want to turn off the unit, press and
hold the multi-function key by 7 seconds to
power off the Bluetooth receiver. The Red
LED will fast flashing 10 times and the unit
turn off accordingly.
Pairing with a different device
Only one device can be paired in each time. To
pair a different Bluetooth device,
•
•
Press and hold the multi-function key around
5 seconds to enter the pairing mode, the Red
LED will blink slowly
Repeat the pairing instruction listed
previously.
SETUP
User Manual
PLAYING MUSIC / CALL OPERATION
Play and Pause
•
•
•
Press the multi-function key to control
Play/Pause of your music after your device
have been paired and playing the music.
To skip to the next song, double click the
multi-function key.
When a call is come while you are playing
music, the music will automatically pause.
Incoming call
1. An incoming call when listen music, LED will
be flashing in Blue color and the ring tone
show in car's speaker system simultaneously.
2. Press the multi-function key once to take the
call, the LED will turn to solid Blue status.
3. You can speak through the microphone of the
Bluetooth receiver
SETUP
User Manual
4. If you want to reject the call, long press the
multi-function key by 2 second to reject it,
and the music will be retrieved.
5. You can simply press the multi-function
button to end the call anytime.
6. When a second call is coming during you are in
answering a call, you can simply press the
multi-function key once to answer the second call.
7. While you are in answering two calls, you can
also press the multi-function key to switch
between two calls.
8. To end the second call, simply double press
the multi-function key, you will enter back
the first call.
9. After you end all the calls, the music will be
retrieved.
SETUP
User Manual
Voice dialing
•
•
•
Make a call using voice dialing. If your mobile
device support voice dialing function, press
and hold the multi-function key by 2 seconds
and release, it can wake up the voice dialing
function.
You can speak through the microphone of the
Bluetooth receiver while you are using voice
dialing function.
After you end all the call, the music will be
retrieved.
Standby mode
•
•
If the Bluetooth receiver is un-pair more than
10 minutes, it will get into standby mode, all
LED off and notable tone.
You should simply press the multi-function
key to re-activate the Bluetooth receiver, you
will hear a tone at the same time.
SAFETY WARNING
User Manual
POWER RATING
Model : BTC1
Power : Receiver (5V 200mA)
Cigarette plug (12V~24V)
SAFETY WARNING STATEMENT
Always use this device by connecting with cigarette
receptacle that its power from car battery.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
...TROUBLE SHOOTING (TBC)
...SAFETY WARNING STATEMENT (TBC)
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.
NOTE
The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance.
Such modifications could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rul
es. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipm
ent generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular i
nstallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning th
e equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Title                           : bt_carkit-fiat-UM-draft-v6
Metadata Date                   : 2014:05:14 09:53:38+08:00
Modify Date                     : 2014:05:14 09:53:38+08:00
Create Date                     : 2014:05:08 15:54:33+08:00
Creator Tool                    : Adobe Illustrator CS6 (Macintosh)
Thumbnail Width                 : 252
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 18733 bytes, use -b option to extract)
Instance ID                     : uuid:d0ff88dd-52be-422e-8598-3a24e687b776
Document ID                     : xmp.did:008011740720681180838874E5ED9B7C
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : uuid:815cbf3b-6e79-4443-a9c2-e34d5e8927ae
Derived From Document ID        : xmp.did:FC7F11740720681180838874E5ED9B7C
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:FF6B71FF122068118083EF4E715B31EC, xmp.iid:008011740720681180838874E5ED9B7C
History When                    : 2014:03:27 18:22+08:00, 2014:05:08 15:54:28+08:00
History Software Agent          : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh)
History Changed                 : /, /
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 74.249042
Max Page Size H                 : 105.000654
Max Page Size Unit              : Millimeters
Font Name                       : Calibri, Calibri-Bold, Calibri-BoldItalic
Font Family                     : Calibri, Calibri, Calibri
Font Face                       : Regular, Bold, Bold Italic
Font Type                       : Open Type, Open Type, Open Type
Font Version                    : Version 5.62, Version 5.62, Version 5.62
Font Composite                  : False, False, False
Font File Name                  : Calibri.ttf, Calibri Bold.ttf, Calibri Bold Italic.ttf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : 明亮
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000004
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003099
Swatch Groups Colorants Black   : 0.003099
Producer                        : Adobe PDF library 10.01
Page Count                      : 13
Creator                         : Adobe Illustrator CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools