H3 SYSTEM BA-110 Bluetooth Adapter User Manual BA 110 Manual v0 9

Download:
Mirror Download [FCC.gov]
Document ID	1605847
Application ID	KmaSZfyvGs8rM8egBqdg9w==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.18kB (227259 bits)
Date Submitted	2011-12-20 00:00:00
Date Available	2011-12-20 00:00:00
Creation Date	2011-12-15 20:08:40
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2011-12-15 20:08:40
Document Title	Microsoft Word - BA-110_Manual_v0.9
Document Creator	PScript5.dll Version 5.2
Document Author:	cybercopman

User’s Manual
Bluetooth Adapter
(Bluetooth adapter for a glucometer)
BA-110
Version 0.8
USA-Federal Communications Commission (FCC)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy. If not installed and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by tuning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver.
Connect the equipment to outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Welcome
Thank you for purchasing Bluetooth adapter (BA-110).
The Bluetooth adapter is a data transmitter that receives data from a glucometer and
sends the data to other devices such as a mobile phone, a gateway, etc. via Bluetooth.
The Bluetooth adapter can be connected to Lifescan(Johnson and Johnson)’s One
Touch Ultra and One Touch Mini/Easy and Ultra2 and Bayer’s CONTOUR
Packaging List
Bluetooth adapter (BA-110)
User’s manual
Descriptions
○
○
○
○
① Body
○
② Cable
③ Connector: Connector to a glucometer
④ Button: A button used for Bluetooth manual transmission
⑤ LED: 2-color(Green and Red) LED
○
○
⑥ Label
⑦ Dry cell cover: Cover below which dry cells are put
8
○
⑧ Button: A button used for Bluetooth pairing
How to Use
1.
[Preparation]
Insert batteries.
Open the cell cover to place AAA 1.5V 2 EA while checking the polarity (+,-) and
then close the cover.
2.
Connect the cable to a glucometer
[Bluetooth pairing]
Bluetooth pairing is an authentication process between a Bluetooth adapter and a target
device that readings are supposed to be sent to.
There are two pairing modes for the Bluetooth adapter, BA-110.
To pair the Bluetooth adapter with a NEW target device.
If it fails, the latest pairing info is preserved. And the Bluetooth adapter can send
readings to the latest paired device.
If you try to pair with the latest paired device, the Bluetooth adapter considers it as
a failure. This feature may make confusion. So it is strongly recommended not to
pair with already paired device again using this pairing mode.
The steps are as follows:
① Disconnect the glucometer if it is connected to the Bluetooth adapter.
② Remove batteries.
③ Press the button several times to discharge or wait for a few minutes.
④ After batteries are inserted and the RED LED blinks twice, click the pairing button
on the back
⑤ When the LED turns RED, the Bluetooth adapter is in pairing standby mode.
⑥ Perform “Device search” in the target device and find a device named as
“AMC_JandJ”.
⑦ Pair the target device with the Bluetooth adapter. PIN code is “1234”.
⑧ If the pairing succeeds, the Green LED blinks twice(2). If fails, Red LED blinks
five(5) times.
3.
[Data transfer]
Measure blood glucose while the adapter is being connected to a glucometer.
The measured data is automatically transmitted to the pre-determined device such
as a mobile phone, a gateway, etc.
If the data transmission succeeds, the Green LED blinks twice(2) and if fails, the
Red LED blinks five(5) times.
4.
It takes more than 10 seconds for the first trial after replacing the batteries.
[Manual data transmission]
Press the button of the Bluetooth adapter while a glcuometer and the adapter are
being connected. The whole readings stored in the glucometer will be
automatically downloaded and sent to the target device.
5.
This feature is for troubleshooting.
[Automatic Wake-up Mode]
z In the state of connection with OneTouch Easy/Mini or OneTouch Ultra II, this
adapter reads data and transfers once every 3 hours.
Cautions
Be sure to carefully read the user’s manual before use.
If you want to change the glucometer with new one, disconnect the glucometer, remove
batteries, press the button several times, wait for a while, insert batteries again, and
connect the new glucometer. And try to take a reading and confirm data transmission.
The sequence is very important.
Keep the Bluetooth adapter in a clean and dry place away from dust or corrosive gases
as well as away from fires
Do not apply any shock or vibration to the product
Do not rub the product with inflammable such as alcohol, benzene, or acetone the can
cause chemical change. Use a dry cloth to prevent the surface from being damaged.
Do not stretch nor bend the cable by force.
Disassembling the product is not advisable.
Troubleshooting
If you have some troubles in data transmission, please check the below
Try to do “Manual transmission” by pressing the button while a glcuometer and the
adapter are being connected.
Replace batteries with new ones.
Try to do “Factory reset and pairing” and take readings.
Specifications
Function: it automatically receives blood glucose data measured from a glucometer and
transmits to a pre-determined device via Bluetooth.
Usable devices: Lifescan(Johnson and Johnson)’s One Touch Ultra, One Touch
Mini/Easy, and compatible devices.
Bluetooth 2.0 Class 2
Power supply: Dry cells AAA 2 EA
Size: 70 × 47 × 16 mm
Weight (other than the batteries): 28 g
Customer service
H3 System Co. Ltd. (Korea)
Phone: +82-42-862-9314
FAX: +82-42-862-9315
E-Mail: info@h3system.co.kr
Homepage: http://www.h3system.co.kr

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2011:12:15 20:08:40+09:00
Create Date                     : 2011:12:15 20:08:40+09:00
Format                          : application/pdf
Title                           : Microsoft Word - BA-110_Manual_v0.9
Creator                         : cybercopman
Document ID                     : uuid:a5177ebf-6f1e-4553-82c6-62f9e050c33b
Instance ID                     : uuid:144b9b91-66bb-4ec8-9790-ea9dfc5f8d7b
Page Count                      : 8
Author                          : cybercopman

EXIF Metadata provided by EXIF.tools