HARRIS TR-0018-E P7100(PI) 800 MHz Portable Land Mobile Radio User Manual MM101332V1R1A FCC Prelim

HARRIS CORPORATION P7100(PI) 800 MHz Portable Land Mobile Radio MM101332V1R1A FCC Prelim

Manual

Operator’s ManualMM101332V1 R1AP7100IPSystem/Scan Portable Radios
2TABLE OF CONTENTSPageSAFETY TRAINING INFORMATION............................................ 3OPERATING RULES AND REGULATIONS ................................. 6OPERATING TIPS............................................................................ 8BATTERY DISPOSAL ................................................................... 12SCOPE OF THIS MANUAL........................................................... 13USER INTERFACE ........................................................................ 14STATUS MESSAGES..................................................................... 19BASIC OPERATION ...................................................................... 22ALERT TONES............................................................................... 27TRANSMITTING A CALL IN TRUNKED MODE ....................... 28RECEIVING A CALL IN TRUNKED MODE ............................... 29CONVENTIONAL OPERATION................................................... 30OPERATION FOLLOWING WATER CONTACT ........................ 31CHANGING THE BATTERY PACK............................................. 33BATTERY WARRANTY ............................................................... 35WARRANTY .................................................................................. 36The software contained in this device is copyrighted by M/A-COM Private Radio Systems, Inc.Unpublished rights are reserved under the copyright laws of the United States.NOTICE!This manual is published by M/A-COM Private Radio Systems, Inc., without anywarranty. Improvements and changes to this manual necessitated by typographicalerrors, inaccuracies of current information, or improvements to programs and/orequipment, may be made by M/A-COM Private Radio Systems, Inc., at any time andwithout notice. Such changes will be incorporated into new editions of this manual. Nopart of this manual may be reproduced or transmitted in any form or by any means,electronic or mechanical, including photocopying and recording, for any purpose, withoutthe express written permission of M/A-COM Private Radio Systems, Inc.Copyright © 2002 M/A-COM Private Radio Systems, Inc. All rights reserved.
3SAFETY TRAINING INFORMATIONWARNINGThe M/A-COM P7100PI portable radiogenerates RF electromagnetic energyduring transmit mode. This radio isdesigned for and classified as“Occupational Use Only,” meaning itmust be used only during the course of employmentby individuals aware of the hazards and the ways tominimize such hazards. This radio is NOT intended foruse by the “General Population” in an uncontrolledenvironment.The P7100PI portable radio has been tested and complieswith the FCC RF exposure limits for “Occupational UseOnly.” In addition, this M/A-COM radio complies with thefollowing Standards and Guidelines with regard to RFenergy and electromagnetic energy levels and evaluationof such levels for exposure to humans:· FCC OET Bulletin 65 Edition 97-01 Supplement C,Evaluating Compliance with FCC Guidelines forHuman Exposure to Radio Frequency ElectromagneticFields.· American National Standards Institute (C95.1 – 1992),IEEE Standard for Safety Levels with Respect toHuman Exposure to Radio Frequency ElectromagneticFields, 3 kHz to 300 GHz.· American National Standards Institute (C95.3 – 1992),IEEE Recommended Practice for the Measurement of
4Potentially Hazardous Electromagnetic Fields – RFand Microwave.CAUTIONTo ensure that exposure to RFelectromagnetic energy is within the FCCallowable limits for occupational use,always adhere to the followingguidelines:· DO NOT operate the radio without a proper antennaattached, as this may damage the radio and may alsocause you to exceed FCC RF exposure limits. Aproper antenna is the antenna supplied with this radioby M/A-COM or an antenna specifically authorized byM/A-COM for use with this radio.· DO NOT transmit for more than 50% of total radio usetime (“50% duty cycle”). Transmitting more than 50%of the time can cause FCC RF exposure compliancerequirements to be exceeded. The radio istransmitting when the “TX” indicator appears in thedisplay. The radio will transmit by pressing the “PTT”button.· ALWAYS use M/A-COM authorized accessories(antennas, batteries, belt clips, speaker/mics, etc).Use of unauthorized accessories may cause the FCCOccupational/Controlled Exposure RF compliancerequirements to be exceeded.
5· ALWAYS keep the device and its antenna at least 2cm (0.8 inches) from the body and at least 5 cm (2inches) from the face when transmitting to ensure FCCRF exposure compliance requirements are notexceeded. This radio has been tested for RFexposure compliance at a distance of 1.6 cm from thebody and 2.5 cm from the face for a worst-casescenario. However, to provide the recipients of yourtransmission the best sound quality, hold the antennaat least 5 cm (2 inches) from mouth, and slightly off toone side.The information listed above provides the informationneeded to make the user aware of a RF exposure, andwhat to do to assure that this radio operates within the FCCRF exposure limits of this radio.ELECTROMAGNETIC INTERFERENCE/COMPATIBILITYDuring transmissions, this M/A-COM radio generates RFenergy that can possibly cause interference with otherdevices or systems. To avoid such interference, turn offthe radio in areas where signs are posted to do so. DONOT operate the transmitter in areas that are sensitive toelectromagnetic radiation such as hospitals, aircraft, andblasting sites.
6OPERATING RULES AND REGULATIONSTwo-way FM radio systems must be operated inaccordance with the rules and regulations of the FederalCommunications Commission (FCC). As an operator oftwo-way radio equipment, you must be thoroughly familiarwith the rules that apply to your particular type of radiooperation. Following these rules will help eliminateconfusion and will assure the most efficient use of existingradio channels. This will provide a smooth operating radionetwork.When using the radio, remember these rules:1. It is a violation of FCC rules to interrupt any distress oremergency message. As the radio operates in muchthe same way as a telephone "party line" when inconventional mode, always listen and/or observe theabsence of the “busy” display (refer to Table 1 – ThreeLine Display for display character) to make sure thatthe line is clear before sending any messages. Ifsomeone is sending an emergency message, such asreporting a fire or asking for help in an accident, KEEPOFF THE AIR! Emergency calls have priority over allother messages.2. Use of profane or obscene language is prohibited byFederal Law.3. It is against the law to send false call letters or a falsedistress or emergency message.
74. The FCC requires that conversations be brief andconfined to business. To save time, use codedmessages whenever possible.5. Using the radio to send personal messages (except inan emergency) is a violation of FCC rules. Send onlythose messages essential for the business operation.6. It is against Federal Law to repeat or otherwise makeknown anything overheard on the radio. Conversationsbetween others sharing your channel must beregarded as confidential.
8OPERATING TIPSAntenna location and condition are important whenoperating a portable radio. Operating the radio in low lyingareas or terrain, under power lines or bridges, inside of avehicle or in a metal or steel framed building can severelyreduce the range of the unit. Mountains can also reducethe range of the unit.In areas where transmission or reception is poor, someimprovement may be obtained by ensuring that theantenna is vertical. Moving a few yards in another directionor moving to a higher elevation may also improvecommunications. Vehicular operation can be aided with theuse of an externally mounted antenna.Battery condition is another important factor in thetrouble free operation of a portable radio. Always properlycharge the batteries.EFFICIENT RADIO OPERATIONHold the portable radio approximately three inches fromyour mouth and speak into the microphone at a normalvoice level.Keep the antenna in a vertical position when receivingor transmitting a message.Do not hold the antenna when receiving a messageand, especially, do not hold when transmitting a message.
9WARNINGDo NOT hold onto the antenna whentransmitting.Antenna Care and ReplacementWARNINGAlways keep the antenna at least 0.8 inches(2 cm.) away from the body and 2 inches (5cm.) from the face when transmitting toensure FCC RF exposure compliancerequirements are not exceeded.WARNINGDo not use the portable radio with a damagedor missing antenna. A minor burn may resultif a damaged antenna comes into contactwith the skin. Replace a damaged antennaimmediately. A missing antenna coulddamage your portable radio.WARNINGUse only the supplied or approved antenna.Unauthorized antennas, modifications orattachments could damage the radio unit andmay violate FCC regulations.
10Electronic DevicesCAUTIONRF energy from your portable radio mayaffect some electronic equipment. Mostmodern electronic equipment in cars,hospitals, homes, etc. are shielded from RFenergy. However, in areas that instruct you toturn off two-way radio equipment, alwaysobserve the rules. If in doubt, turn it off!AircraftWARNINGAlways turn off your portable radio beforeboarding any aircraft!· Use it on the ground only with crewpermission.· DO NOT use while in-flight!!Blasting AreasWARNINGTo avoid interfering with blasting operations,turn your radio OFF when in a "blasting area"or in areas posted "turn off two-way radio."Remote control RF devices are used by someconstruction crews to set off explosives.
11Potentially Explosive AtmospheresWARNINGAreas with potentially explosive atmosphereare often, but not always, clearly marked.These may be fueling areas, such as gasstations, fuel or chemical transfer or storagefacilities, and areas where the air containschemicals or particles, such as grain, dust ormetal powders.Sparks in such areas could cause anexplosion or fire resulting in bodily injury oreven death.Turn OFF your radio when in any area with apotentially explosive atmosphere. It is rare,but not impossible that the radio or itsaccessories could generate sparks.
12BATTERY DISPOSALThe P7100IP portable radios use rechargeable,recyclable Nickel Cadmium (NiCd) or Nickel Metal Hydride(NiMH) batteries.NICKEL CADMIUM BATTERY PACK DISPOSALAt the end of its useful life, undervarious state and local laws, it maybe illegal to dispose of the NickelCadmium batteries into themunicipal waste stream. Check withlocal solid waste officials for detailsof recycling options or proper disposal. Call Toll Free 1-800-8BATTERY for information and/or procedures forreturning rechargeable batteries in your state.NICKEL METAL HYDRIDE BATTERY PACKDISPOSALThere are no special requirements concerning thedisposal of NiMH batteries. Batteries can be recycled. CallToll Free 1-800-8BATTERY for information.
13SCOPE OF THIS MANUALThis manual describes the basic functions andoperation of the P7100IP System/Scan portable radios. Foradditional information about the features and operationrefer to the appropriate Maintenance Manual or contact theSystem Administrator.WATER RESISTANCEThe P7100IP portable radios operate reliably evenunder adverse conditions. These radios meet MIL-STD-810F specifications for driven rain, humidity, and salt fog.
14USER INTERFACEFigure 1 – Top View
15Figure 2 – Side View
16Figure 3 - System Keypad
17Figure 4 – Scan Keypad
18Table 1 – Three Line DisplayIcon DescriptionsSteady – “Busy”transmitting orreceivingFlashing – call queuedSteady – special callmode (individual ortelephone)Steady – during allradio transmissionsSteady – transmit atlow powerIf icon is not visible –transmit at high powerSteady – low battery Steady – group orchannel in scan listSteady – trunkedsystem in FailsoftmodeSteady – priority 2group or channelSteady – transmit inencrypt modeFlashing – receivingan encrypted callSteady – priority 1group or channelSteady – scan mode(rotates clockwise)If icon is not visible –scan disabledSteady – ChannelGuard enabledIf icon is not visible –Channel Guarddisabled
19STATUS MESSAGESDuring radio operation, various radio status messagescan be displayed. The messages are described below.MESSAGE NAME DESCRIPTIONQUEUED Call Queued - Trunked mode only. Indicatesthe system has placed the callin a request queue.SYS BUSY System Busy - Trunked mode only. Indicatesthe system is busy, no channelsare currently available, thequeue is full or an individual callis being attempted to a radiothat is currently transmitting.DENIED Call Denied - Trunked mode only. Indicatesthe radio or talkgroup is notauthorized to operate on theselected system and/ortalkgroup.CC SCAN Control ChannelScan - Trunked mode only. Indicatesthe control channel is lost andthe radio has entered theControl Channel Scan mode tosearch for the control channel.(Usually out of rangeindication.)
20MESSAGE NAME DESCRIPTIONWA SCAN Wide Area Scan - Trunked mode only. Indicatesthe radio has entered the WideArea Scan mode to search for anew system (if enabled throughprogramming).TALKARND Talkaround -Conventional mode only.Indicates the radio is operatingon conventional channels intalkaround mode (no repeater).SYSC ON System ScanFeatures On - Trunked mode only. Indicatesthe System Scan features areenabled.SYSC OFF System ScanFeatures Off - Trunked mode only. Indicatesthe System Scan features aredisabled.LOW BATT Low Battery - Battery voltage has droppedbelow the point to where theradio is no longer able totransmit. The radio will still beable to receive calls until thebattery is discharged beyondthe point of operation uponwhich the radio willautomatically shutdown.
21MESSAGE NAME DESCRIPTIONRXEMER ReceiveEmergency - Trunked mode only. Indicatesan emergency call is beingreceived. This message will beflashing on line two.TXEMER TransmitEmergency - Trunked mode only. Indicatesan emergency call has beentransmitted on this radio. Thismessage will be flashing on linetwo.VOL=31 Volume Level - Indicates the current volumelevel. The volume level displayranges from OFF (silent) to 31(loudest).WHC Who Has Called - trunked mode only. Indicatesan individual call has beenreceived, but not responded to.The indicator turns OFF if theindividual call mode is entered,the system is changed, or theradio is turned off and then backon.UNKNOWN Unknown ID - Trunked mode only. Indicatesan individual call is beingreceived by an unknown radioID.
22BASIC OPERATIONSYSTEM SELECT – METHOD 1 (SYSTEM)1. Press 1 to access system list.2. Enter system ID number from keypad.3. Press m to select desired system.SYSTEM SELECT – METHOD 2Rotate System/Group/Channel knob, orIf this knob is not programmed for systems, press the ud buttons to change systems.GROUP SELECT – METHOD 1 (SYSTEM)1. Press 2 to access group list.2. Press u d to scroll through the list of groups.3. Press m to select desired group.GROUP SELECT – METHOD 21. Rotate System/Group/Channel knob.If this knob is not programmed for groups:2. Press the u d buttons to change groups.
23CHANNEL SELECTRotate System/Group/Channel knob, orIf this knob is not programmed for channels, press the ud buttons to change channels.MODIFY SCAN LIST (SYSTEM)1. Press 3 to toggle scan OFF and verify is notdisplayed.2. Select group or channel.3. Press 9 once to remove group or channel from list.4. Press 6 once to add as a normal group or channel.Press 6 twice to add as a Priority 2 group.Press 6 three times to add as a Priority 1 group.5. Press 3 to re-start scanning.NUISANCE DELETE (SYSTEM MODEL)A channel can temporarily be deleted from the scan listif it is not the currently selected channel.1. Turn Scan ON.2. When the radio receives a call on the channel, pressthe 9. The channel is removed from the scan listuntil the radio is power cycled.
24MODIFY SCAN LIST (SCAN MODEL)1. Press s to toggle scan OFF and verify is notdisplayed.2. Select group or channel.3. Press a once to remove group or channel from thelist.4. Press a once to add as a normal group orchannel.Press a twice to add as a Priority 2 group.Press a three times to add as a Priority 1 group.5. Press s to re-start scanning.BACKLIGHT ON/OFF1. Press m to access the menu.2. Press u d to scroll through menu until “BCKLGHT”appears.3. Press m to select Backlight menu.4. Press u d to toggle backlight ON and OFF.5. Press m to select new backlight setting.
25CONTRAST ADJUST1. Press m to access the menu.2. Press u d to scroll through menu until“CONTRAST” appears.3. Press m to select Contrast menu.4. Press u d to adjust contrast setting from 1 - 4.5. Press m to select new contrast setting.DECLARING AN EMERGENCY1. Press and hold the red Emergency/Home button (thelength of time is programmable; check with the systemadministrator).2. *TXEMER* will flash in the display, plus and willbe displayed. After 2-3 seconds the transmit icon will turn off.3. *TXEMER* and will remain until the emergency iscleared.
264. Press the PTT and will reappear.5. Release PTT when the transmission is complete.LOCKING/UNLOCKING KEYPAD1. Press m button.2. Within 1 second, press the Option button on the sideof the radio.
27ALERT TONESName Tone DescriptionCallOriginate(B) one shortmid-pitchedOK to talk after pressing the push-to-talk buttonCallQueued(T) one high-pitchedcall in a queue for processingAutokey (T) one mid-pitchedqueued call received channelassignmentSystemBusy(T) three low-pitchedsystem busy or unable tocomplete callCall Denied (T) one low-pitchedradio is not authorized on thesystem or groupCarrierControlTimer(B) five high-pitched /one longlow-pitchedPTT depressed for maximumlength of timeLowBattery(B) one low-pitched /one shortmid-pitchedlow batteryTX LowBatteryAlert(B) one low-pitchedafter PTT - battery too low totransmit(T) = trunked mode only (B) = both trunked and conventional modes
28TRANSMITTING A CALL IN TRUNKED MODEGROUP CALL1. Select desired group.2. Press Push-To-Talk button.3. The and icons will appear.INDIVIDUAL CALL (SYSTEM)1. Press # to access the individual call list.2. The icon will appear.3. Press u d to scroll through individual call list orEnter LID from keypad.4. When the desired ID appears in the display press thePush-To-Talk button.5. The and icons will appear.PHONE CALL (SYSTEM)1. Press * to access the phone call list.2. The icon will appear.3. Press u d to scroll through phone call list or Enternumber from keypad.4. When the desired phone number appears in thedisplay press the Push-To-Talk button.5. The and icons will appear.
29RECEIVING A CALL IN TRUNKED MODEGROUP CALLS1. Select a group or turn scan ON and make sure groupis in scan list.2. The group name or “GR xxxxx” will appear to indicatea call.PHONE CALLS1. When the call is received, the receive audio soundsand the display reads: *PHONE*2. Respond by pressing PTT. If you do not respond,radio will continue to ring to indicate an incoming call.INDIVIDUAL CALLS1. When the call is received, the receive audio soundsand the display reads : ID xxxxx *INDV*2. Respond by pressing PTT. If you do not respond,radio will continue to ring to indicate an incoming call.3. If the call is cleared with no response, the radio willstore Who Has Called and display:*WHC*4. Press the # key to display the ID.5. Press the Push-To-Talk button to return the call orpress the Clear/Monitor button to clear the *WHC*.
30CONVENTIONAL OPERATIONRECEIVING A CALL1. Select desired conventional system and channel orturn scan ON and make sure desired channel is inscan list.2. When the radio receives a call, the radio will unmuteand the channel name will appear in the display.SENDING A CALL1. Select desired system and channel.2. Ensure the channel is not busy by pressing theMonitor/Clear button momentarily. If you hear audioor if the icon is on, the channel is busy.3. When you are sure the channel is not busy, press thePush-To-Talk button and speak into the microphone.
31OPERATION FOLLOWING WATER CONTACTIf the P7100IP model radio has been immersed in wateror if the microphone air path or speaker grill becomeclogged with water, follow instructions under “RadioMicrophone and Radio Speaker” to assure the highestquality transmitted and received messages.RADIO MICROPHONEIn the event the P7100IP microphone air path becomesclogged with water, blow two quick successive breaths ofair directly into the radio microphone air hole. Refer toFigure 5. This will help to clear any water trapped in themicrophone air path and allow the microphone to functionproperly.Figure 5 – Radio Microphone
32RADIO SPEAKERTo assure the user receives the highest quality receiveaudio possible after the radio has contacted water or beenimmersed, it may be necessary to clear excess water fromthe speaker cavity and grill. The speaker grill has beendesigned for easy drainage. To facilitate maximumdrainage and the highest quality speaker output, shake theradio vigorously with speaker grill face down.
33CHANGING THE BATTERY PACKREMOVING THE BATTERY PACKMake sure the power to the radio is turned OFF.1. Press the latch at the bottom of the battery pack.2. Lift the battery pack from the bottom.3. Remove the battery pack from the radio.Figure 6 – Removing the Battery Pack
34ATTACHING THE BATTERY PACKMake sure the power to the radio is turned OFF.1. Align the tab on the top of the battery pack with theslot at the top of the battery cavity.2. Push the battery pack down to attach the battery to theradio.3. Verify that the battery pack is properly latched to theradio.Figure 7 – Attaching the Battery Pack
35BATTERY WARRANTYA. M/A-COM Private Radio Systems, Inc. (hereinafter "Seller") warrants to theoriginal purchaser for use (hereinafter "Buyer") that nickel-cadmium and nickel-metal hydride batteries supplied by Seller shall be free from defects in materialand workmanship, and shall conform to its published specifications for a periodof twelve (12) months from the date of purchase.B. For purposes of this warranty, batteries shall be deemed defective if (1) thebattery capacity is less than 80% rated capacity, or (2) the battery developsleakage.C. If any battery fails to meet the foregoing warranty, Seller shall correct thefailure by issuing a replacement battery upon receipt of the defective battery atan Authorized Service Center (ASC). To obtain the name and address of anASC, ask your salesperson, consult the Yellow Pages, or call the numberprinted at the bottom of this page.D. Replacement batteries shall be warranted only for the remaining unexpiredwarranty period of the original battery. This warranty becomes void if:1. The battery has been subjected to any kind of misuse, detrimentalexposure, or has been involved in an accident.2. The battery is used in equipment or service other than the radioequipment for which it is specified.E. The preceding paragraphs set forth the exclusive remedies for claims (exceptas to title) based upon defects in or non-conformity of any battery, whether theclaim is in contract, warranty, tort (including negligence), strict liability orotherwise, and however instituted. Upon the expiration of the warranty period,all such liability shall terminate. The foregoing warranties are exclusive and inlieu of all other warranties, whether oral, written, expressed, implied orstatutory. NO IMPLIED OR STATUTORY WARRANTIES OFMERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALLAPPLY. IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANYINCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARYDAMAGES.This warranty applies only within the United States.M/A-COM Private Radio Systems3315 Old Forest RoadLynchburg, Virginia 245011-800-528-7711 AE/LZT 123 3248/2 R4A
36WARRANTYA. M/A-COM Private Radio Systems, Inc. (hereinafter "Seller") warrants tothe original purchaser for use (hereinafter "Buyer") that Equipmentmanufactured by or for the Seller shall be free from defects in material,workmanship and title, and shall conform to its publishedspecifications. With respect to any Equipment not manufactured by orfor the Seller (except for integral parts of Seller's Equipment to whichthe warranties set forth above shall apply), Seller gives no warranty,and only the warranty, if any, given by the manufacturer shall apply.Batteries are excluded from this warranty but are warranted under aseparate Battery Warranty.B. Seller’s obligations set forth in Paragraph C below shall apply only tofailures to meet the above warranties (except as to title) occurringwithin the following periods of time from date of sale to the Buyer andare conditioned on Buyer’s giving written notice to Seller within thirty(30) days of such occurrence:1. for fuses and non-rechargeable batteries, operable on arrivalonly.2. for parts and accessories (except as noted in B.1) sold bySeller’s Service Parts Operation, ninety (90) days.3. for PANTHERä Series handportable and mobile radios, two (2)years.4. for Cougarä Series handportable and mobile radios, two (2)years.5. for all other Equipment of Seller’s manufacture, one (1) year.C. If any Equipment fails to meet the foregoing warranties, Seller shallcorrect the failure at its option (i) by repairing any defective ordamaged part or parts thereof, (ii) by making available at Seller’sfactory any necessary repaired or replacement parts, or (iii) byreplacing the failed Equipment with equivalent new or refurbishedEquipment. Any repaired or replacement part furnished hereunder shallbe warranted for the remainder of the warranty period of the Equipmentin which it is installed. Where such failure cannot be corrected bySeller’s reasonable efforts, the parties will negotiate an equitableadjustment in price. Labor to perform warranty service will be providedat no charge during the warranty period only for the Equipmentcovered under Paragraph B.3. To be eligible for no-charge labor,
37service must be performed by an Authorized Service Center (ASC) orother Servicer approved for these purposes either at its place ofbusiness during normal business hours, for mobile or personalequipment, or at the Buyer’s location, for fixed location equipment.Service on fixed location equipment more than thirty (30) miles fromthe Service Center or other approved Servicer’s place of business willinclude a charge for transportation.D. Seller’s obligations under Paragraph C shall not apply to anyEquipment, or part thereof, which (i) has been modified or otherwisealtered other than pursuant to Seller’s written instructions or writtenapproval or, (ii) is normally consumed in operation or, (iii) has a normallife inherently shorter than the warranty periods specified in ParagraphB, or (iv) is not properly stored, installed, used, maintained or repaired,or, (v) has been subjected to any other kind of misuse or detrimentalexposure, or has been involved in an accident.E. The preceding paragraphs set forth the exclusive remedies for claims(except as to title) based upon defects in or nonconformity of theEquipment, whether the claim is in contract, warranty, tort (includingnegligence), strict liability or otherwise, and however instituted. Uponthe expiration of the warranty period, all such liability shall terminate.The foregoing warranties are exclusive and in lieu of all otherwarranties, whether oral, written, expressed, implied or statutory. NOIMPLIED OR STATUTORY WARRANTIES OF MERCHANTABILITYOR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY. IN NOEVENT SHALL THE SELLER BE LIABLE FOR ANY INCIDENTAL,CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARYDAMAGES.This warranty applies only within the United States.M/A-COM Private Radio Systems3315 Old Forest RoadLynchburg, VA 245011-800-528-7711 AE/LZT 123 3248/1 R5A
38NOTES
39NOTES
M/A-COM Wireless Systems3315 Old Forest RoadLynchburg, Virginia 24501(Outside USA, 434-385-2400) Toll Free 800-528-7711www.macom-wireless.com Printed in U.S.A.

Navigation menu