HARRIS TR-0019-E VHF 110W Mobile Radio User Manual

HARRIS CORPORATION VHF 110W Mobile Radio 6839 7

a href="https://usermanual.wiki/HARRIS" itemprop="url"> HARRIS >

Contents

Antenna Install Info

Roof Top Mount MOBILE ANTENNAfor 132-960 MHzWHERE TO MOUNT THE ANTENNACenter roof top mounting is recommended for best performance on cars, vans or trucks with metal tops.For most center roof top installations, the underside of the mounting surface will be exposed by removingthe interior dome light, be sure mounting surface is a single thickness of sheet metal. This antenna mayalso be mounted on any flat, horizontal, metallic surface.The use of PTFE or similar lubricant on the threaded portions and O-Rings of the antenna, prior to assem-bly, will protect from weather and ease future disassemblyFIG. 1ASP1810MAAllen WrenchLarge O-RingBaseSpanner WrenchAdapterWhip AdapterMount & CableSmall O-RingWhipSet ScrewMini-UHF (crimp) RG-58/UTNC RG-58/UTHIS PACKAGE CONTAINS COMPONENTS FOR THE CONFIGURATIONS SHOWN BELOW.A product of M/A-COM. Inc.www.macom.com
page 2 127-217-1 9/03MountingSurfaceToggle BarFIG. 2INSTALLATION INSTRUCTIONS1. Select mounting location. Center punch and drill 3/4”diameter hole (Fig. 2). Use a sheet metal punch orhole saw. Remove any burs from around hole.2. If the under side of the mount location is accessible,the cable may be routed for the interior. Otherwise thecable must be fed through the hole and routed fromthe mount location.3. Route cable to radio location, using care to avoidareas where the cable may become damaged.4. Screw toggle bar onto stanchion. Apply a smallamount of PTFE lubricant in the groove on the underside of the mount adapter. Place the O-Ring in thegroove. The O-Ring will remain in place while mountadapter is threaded onto the Stanchion.5. If the underside of the mounting location is acces-sible, push the stanchion up through hole and have ahelper thread the mount adapter on stanchion. Other-wise thread the mount adapter onto the stanchion afew turns. Holding the mount adapter, angle thestanchion into the hole as shown in Fig. 3. Adjust thetoggle bar to achieve .550” dimension (Fig. 4).6. Align centering boss on the under side of the mountadapter in hole and use spanner wrench to tightenmount adapter securely (Fig. 4). Be sure mount doesnot rotate. Slide O-Ring over mount adapter (Fig. 4).7. Assemble whip and antenna parts onto mountadapter as shown in (Fig, 1). Tighten all parts se-curely.8. Attach appropriate connector to end of cable at radio(SEE CONNECTOR ASSEMBLY INSTRUCTIONS)9. Screw connector onto antenna receptacle of radio tocomplete installation.10. Refer to tuning instructions as follows.TUNING:1. It is recommended that an Antenna Tester beused to verify and tune the antenna acrossthe entire specified frequency band. Connectthe Antenna Tester between the transceiverand the antenna.2. Cut whip length to achieve desired frequencyper appropriate cutting chart. Remove sharpburrs.3. Loosen set screw and bottom whip into whipadapter. Tighten set screw.4. When tuning is complete, disconnect theAntenna Tester and connect the Transceiverto the antenna.StanchionSpannerWrenchAdapterSquare C/S“O” Ring3/4” hole Toggle BarAdapterAdapterMountingSurfaceFIG. 4FIG. 3Centering Boss
Download:
Mirror Download [FCC.gov]
Document ID366286
Application IDQULtc/XkSXfOk/ukwtyUxA==
Document DescriptionAntenna Install Info
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.55kB (156899 bits)
Date Submitted2003-10-20 00:00:00
Date Available2003-12-10 00:00:00
Creation Date2003-09-08 16:43:18
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2003-10-20 09:58:17
Document Title6839-7
Document CreatorAdobe PageMaker 7.0
Document Author: HStampe
FCC ID Filing: OWDTR-0019-E

Navigation menu