HBC radiomatic TF011 RFID Reader User Manual

HBC-radiomatic GmbH RFID Reader

user manual

Download: HBC radiomatic TF011 RFID Reader User Manual
Mirror Download [FCC.gov]HBC radiomatic TF011 RFID Reader User Manual
Document ID3928115
Application IDPeNd7rfeDzRYtgePfzAnkw==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize21.64kB (270501 bits)
Date Submitted2018-07-18 00:00:00
Date Available2018-07-18 00:00:00
Creation Date2018-07-12 13:42:36
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2018-07-12 13:42:36
Document Titleuser manual
Document CreatorMicrosoft® Word 2010

TF0110__ integration manual
HBC
Introduction ....................................................................................................................................... 1
Installation ......................................................................................................................................... 1
2.1
Possible Hosts ............................................................................................................................ 1
2.2
Installation process ..................................................................................................................... 1
Authorization requirements ............................................................................................................. 3
Labeling requirements for the host ................................................................................................ 3
RF exposure statement (mobile and fixed devices) ...................................................................... 3
RF exposure statement (portable devices) .................................................................................... 3
Instruction manual requirements .................................................................................................... 3
Introduction
This document describes the installation of TF0110__ into the HBC-transmitter.
Installation
2.1
Possible Hosts
The module TF011010 may be installed in every HBC-transmitter. It has to be supplied with a DC voltage of 3.0 V
up to 5V. The module TF011010 has an integrated RFID-antenna. So there is no need for an antenna installation.
2.2
Installation process
First of all the TF011010 module has to be put into the groove of the transmitter housing as the next picture shows.
Author: Florian Abelein
Date: 08.06.2018
Seite 1 von 4
Revision: 0
TF0110__ integration manual
HBC
As next step the connection cable has to be pushed into the TF011010 interface connector of the mainboard as the
next picture shows:
FCC
The Federal Communications Commission (FCC) warns the users that changes or modifications to the unit
not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
FCC §15.105 (b):
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This euipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Canada
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Author: Florian Abelein
Date: 08.06.2018
Seite 2 von 4
Revision: 0
TF0110__ integration manual
HBC
Authorization requirements
The integrator of a certified module is responsible for ensuring that the end product consisting of host and
module(s) installed continues to be compliant with all the intentional radiator requirements applicable to the
module(s) and the host. When additional application filing for RF exposure compliance demonstration is not
required, the host manufacturer may do evaluation without any filing if compliance with transmitter output power,
out-of-band, restricted band, and spurious emission requirements as specified in 47 CFR Part 15 subpart C and
appropriate ISED Radio Standards Specifications (RSS) is confirmed for the end product.
The host manufacturer is also responsible for ensuring that the host continues to be compliant with the 47 CFR
Part 15 subpart B unintentional radiator requirements after the module is installed and operational. Therefore, the
procedure for equipment authorization of unintentional radiators as stated in §15.101 applies to the end product,
too.
Labeling requirements for the host
At the HBC-transmitter into which the TF011010 module is installed the label has to be added with the following
content:


Contains FCC ID: NO9TF011
Contains IC: 2977A-TF011
RF exposure statement (mobile and fixed devices)
This device complies with the RF exposure requirements for mobile and fixed devices. However, the device shall
be used in such a manner that the potential for human contact during normal operation is minimized.
RF exposure statement (portable devices)
This device complies with the RF exposure SAR test exclusion requirements for portable devices, if a minimum
separation distance (1 mm ) is kept. However, the device shall be used in such a manner that the potential for
human contact during normal operation is minimized.
Instruction manual requirements
The following content has to be added in the instruction manual of the HBC-transmitter which contains the
TF011010 module:
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.”
Modification of equipment
The instruction manual of the host shall include the following statement:
Changes or modifications made to this equipment not expressly approved by the party responsible for
compliance may void the FCC authorization to operate this equipment.
Information to the user
(The instruction manual of the host shall include the following statement)
Author: Florian Abelein
Date: 08.06.2018
Seite 3 von 4
Revision: 0
TF0110__ integration manual
HBC
FCC §15.105 (b):
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This euipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Canada
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Special accessories
Where special accessories such as shielded cables and/or special connectors are required to comply with
the emission limits, the instruction manual shall include appropriate instructions on the first page of the text
describing the installation of the device.
Simultaneous transmission
When the host product supports simultaneous-transmission operations the host manufacturer needs to
check if there are additional RF exposure filing requirements due to the simultaneous transmissions. When
additional application filing for RF exposure compliance demonstration is not required (e. g. the RF module
in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous
transmission SAR test exclusion requirements), the host manufacturer may do his own evaluation without
any filing, using reasonable engineering judgment and testing for confirming compliance with transmitter
output power, out-of-band, restricted band, and spurious emission requirements in the simultaneoustransmission operating modes.
If additional filing is required please contact the person at HBC Radiomatic responsible for certification of
the RF module.
Author: Florian Abelein
Date: 08.06.2018
Seite 4 von 4
Revision: 0

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
Language                        : de-DE
Producer                        : Microsoft® Word 2010
Creator                         : Microsoft® Word 2010
Create Date                     : 2018:07:12 13:42:36+02:00
Modify Date                     : 2018:07:12 13:42:36+02:00
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NO9TF011

Navigation menu