HENAN ESHOW ELECTRONIC COMMERCE AILUNCEHD1 DMR Digital Transceiver User Manual part 2
HENAN ESHOW ELECTRONIC COMMERCE CO., LTD DMR Digital Transceiver part 2
Contents
- 1. User manual part 1
- 2. User manual part 2
- 3. User manual part 3
User manual part 2
Write Message Choose write to write your message before sending it . Press [ @%) or 2B ] key to edit, then press [ (@B ] key to select. 2. A flashing cursor appears, using the keyboard to input messages, press [ § ) key to move to the left one, press [ @@] button to the right one, when editing area have content , press the [@R ] key to delete any useless character, otherwise when editing area without content to return previous interface . After editing the text, press [@@B] to choose to send or save. When editing, user can choose by pressing the [@@D ] to clear all edited message, quickly back to previous interface . Choose send message then press [ @@) or @@B] key to the alias name or ID, and then press [ &D ] key to select. Or Press [ @9 or @@B ] to manual dialing, and then press [@D ] button, enter your user ID and Press {@D ] to send The screen shows message,, confirm sending message. If the messages sent successfully, issued a prompt sound, and the screen displays text message has been sent. Or if the message was not sent, issued a high tone hint sound, and screen displays text message sent failure > o ~® Managing the Sent Items Once a message has sent to another radio, it will be saved in the "Sent Items". After message sent, sending message has always been to "Sent Items" at the top of the list The sent items folder can store up to 50 recently send text messages. After the folder is full, the next send text messages will automatically replace the earlier messages in this folder. Note: press [ ] can return to the previous interface at any time View Sent Items Text Using menu function, 1. Press [@D] to menu mode. 2. Press [ @%) or @@B] message, press [@ZD ] to selection. 3. Press [ @¥) or @@B] to sent items, press [@® ] to selection 4. Press [ @%) or @@B] to required message, press [ &D ] to selection Sending Sent Message When view the Sent Items, you can choice the following, * Resend * Forward * Delete . When view the message, press [(@B] again Press [ @%) or @@B] to resend, press [ @ZB] to select The screen showing send to: , confirm the message is ready sending to same goal radio. . If the message send success, the radio will appear the voice, and sereen showing message sent out. Or If the message send failure, the radio will appear the high voice, and screen showing message sent failure. The screen will return the resend one, press [@ZD ] to resend the message to the same User / Call group name or ID. en o * Select edit, before sending edit the required message. * Select delete, delete required message. Receive Message When your radio on receiving message, the screen in left will show message icon for sending name or ID. When receive message, you can choice the following, * View Delete Note: If you press the [PTT] key while the radio is displaying the prompt screen, the radio exits the Message prompt screen View message 1. Press [ @% or @B] to view, press [@D ) to selection 2. Open the required message in the receiver box 3. Press [ @R] to return the In Box, press [@B ] to reply, forward or delete message, Press [ @B or @2 ] to view, or delete screen * Select view the screen before return received message. * Select delete, delete received message Administrate Received Message Using the inbox to administrate, the receiver box will store 50 messages. Radio support the following function, * Reply * Forward Delete an According to the recently received message to store message which on the receive box. Attention: anytime Press [@B9] can be return the Previous screen. View the Message in the In Box 1. Press [ZD ] to menu mode 2. Press [@¥® or @@B] to message, press [(ZB ] to selection 3. Press [@% or @@B] to InBox, press [ B ] to selection 4. Press [ or @@B] to check message 5. Press [@ZD J select the current message to edit, then press [@RD ] again to reply, delete or forward message Reply the InBox message Using menu function, . Press [( ] to menu mode. Press [ @ or §@BJ to message, press [ @D] to selection. Press [ @ or @@BJ to InBox, press [@ZB ] to selection Press [ @ or @@BJ to required message , press [@@B] to selection. Re—Press [(@B ] to sub—menu. Press [ @ or @@BJ to reply, press [ @B ] to selection.. Screen showing message: confirm on sending message If the message sending succeed, radio appear the voice, and the screen showing message been sent. Or if the message can not send, screen showing sent failure, if message send failure, radio will return the re—send select P NpPP® WR in Delete Message On the Receiver Box Using menu function, 1. Press [@B] to menu mode. . Press [ @¥ or @@B ] to message, Press [ B ] to selection. Press [ @¥) or @2 ] to InBox, Press [(ZB ] to select . Press [ @ or @@B ] to required message , Press [@B ] to selection. . Re—press [@@D] to sub—menu. . Press [ @ or @@B ] to delete, Press [&ZB ] to selection. Screen return to InBox w o ue en Encryption If use this function, it will be good for preventing other user in the channel eaves drop which utilize software encryption but can not allow Some of the transmit sign and user recognition have not done encryption. Even though the receiving have not required encryption, your radio must turn on the encryption on the channel, then can sending the eneryption Basic Encryption Radio could allocate any of the encryption. If it need decode encryption for calling out or data transfer, you must deal the same encryption code with the one on programming and transmitting radio. If your radio receives encrypted calls with different encryption keys or different key values and key ID, you will hear the messy sound of transmission as Confidentiality You can activate or kill any radio. For example, maybe you want to stop one robbed radio, prevent the thief from using it , you can enable it when you get it back. Attention: when use the radio kill or activate only for the one have these function Radio Kill Using menu function, 1. Press [@® ) to menu mode 2. Press [@) or @@D ] to contacts, press [@B ] to select, item according the alphabetical order to rank. . Press [@ or 2B ] to manual dial, Press [@D] to put ID, press [ &D ] to selection Press [@¥) or @2 ] to radio kill, press [ &D ) to select Screen showing radio remote kill and LED indicator light is red a s o Radio Wake Up Using menu function, 1. Press [@B ] to menu mode. 2. Press [@B) or @B] to contacts, press [@@B ] to select, item according the alphabetical order to rank. 3. Press [@) or @@B ) to manual dial, press [ @ ] to put ID, press [( ] to selection 4. Press [@) or @@B] to radio wakeup, press [ ] to selection. 5. Sereen showing radio wakeup and LED indicator light is red. tae Radio ID Can be set up 32 ID. 1. Press [@B] to menu mode. 2. Press [@ or @@B] to radio ID, press [@D] to selection. 3. Press [@M or @B] to select, press [@ZD] to revise ID code, press [ B ] to revise ID name 4. Press [( ] to confirm. 5. Edit ID code or ID name, press [@) or @@B] to move left right character, press [ GR ] to delete character Radio 1. Press [@ZD ] to menu mode 2. Press [@ or @B] to radio, press [ &D ] to enter. 3. Press [@M or @@B to select radio frequency or channel, or input the frequency or channel directly with keypad. 4. Press [@ZB ] to scan, press [or ] to select up or down scan Press [@BB ] to open radio monitor, LCD sereen shows DW, press [ @BB] twice time to close radio monitor. Press [@B ] to close. Save Radio 1. Press [@B] to menu mode. 2. Press [@) or @@] to save radio, press [@ZB ] to input 3. Long press [ @B ] about 2 second into memory channel . Press [ @¥) or BJ to choice required memory channel, press [@@D] to contirm. . Long press [ @B9] to change to channel mode Re—press [ &D ] to close Start and Stop Scan Before using scan, you need decide that any condition should be detective radio sign nd how to continue scan, with the following three mode, 1. (TO: time operation mode ); When the radio detects a signal it will stop scanning and will pause for 5 seconds before scanning again even if the signal is still present . (GOzearrier operation mode): When the radio detects a signal it will stop scanning and will stay on the same frequency and will resume scanning after 5 seconds when the signal ends . (8E: search operation mode): When the radio detects a signal, it will stop on that frequency and will not move on, even if the signal ends .. Start scan: press [@B] about 1 second Press scan state, press [ @%}] to choose up scan, press [@@B] to choose down scan, press any key to exit scan. Dual Standby Short press [@&BB ] key to open or close dual standby, when open dual standby, the sereen will shows two bands, close it will shows single band and time A/B Band Switch Short press [ @9 ] key to switch A/B band Analog/Digital Mode Switch Long Press [ @9 ] key to switch Analog/Digital mode under frequency mode Version Showing Radio Version 1. Press [@ZB ] to menu mode. 2. Press [@ or @B] to radio version, press [ &D ] to selection 3. Screen will appear the current fixed version. Open Password Through program software to set up password, password for 6 significant digits. Initialization If the radio set up open password, it will not operate this function 1. Press [ @®] and [ @R] to open radio, press initialization selection 2. Press [@) or @@B] and [@ZD] to select an First. Main Set NO. | Screen Display Settings Menu Introduction 01 Squelch 0/1..9 Squelch Level 02 Save OFFMMIA2NINA Receiver Power Saving Switch 03 Voice OFF/ON Voice Prompt 04 Vox Delay 0.59/1.08/...5.08 Vox Delay Setting 05 Hang Up OFFMS/2S!...108 Hang Up Calling 06 Tx Channel EDIT/BUSY 15... 108 Priority Transmit Channel 07 Key Define Key Define 08 Backlight ContAuto:18...208 Backlight Setting 09 Beep OFFION Beep Switch 10 Key Lock Manual/Auto Keypad Lock Switch 11 CH—Mode FREQ/NAME/CH Channel Mode 12 Scan Mode TOICOISE Scan Mode 13 Save Ch ©H—0001...3000 Save Channel 14 Delete Ch ©H—0001...3000 Delete Channel 15 Roger OFFION Launch End Tone 16 Time Time Setting 17 Voice Tall OFFION Voice Tail Elimination Squelch Level The higher level, the deeper squeich 1. Press [@D] to menu mode. 2. Press [@ or @@B] to whole set up, press [ @@P ] to selection. 3. Press [@M or @@B] to squeich level, press [@ZB] to selection 4. Press [ @ or @@BJ to choice 0/1/2...9, press [ (@B ) to confirm 5. The function is available in analog channel Save The greater the proportion of power saving, the more standby power 1. Press [@@D ] to menu mode 2. Press [@¥) or @@B] to Main Set,, press [ B ] to selection. 3. Press [@) or @@B] to battery save, press [@@D ) to selection. 4. Press [ @B or @BJ to choose battery save proportion or close, press [@B ] to contirm Voice Open voice, when you press the keypad will voice prompt. 1. Press [@D ] to menu mode 2. Press [@ or @@B] to Main Set, press [ B ] to selection. 3. Press [@ or @@B] to voice, press [@ZB ] to selection 4. Press [@B or BJ to choose open or close, press [@@B] to selection Vox Delay 1. Press [@@D ] to menu mode 2. Press [@) or @@B] to whole setting, press [ @R ] to selection 3. Press [@) or @@B] to VoxDelay, press [@D ] to selection 4. Press [@) or @@BJ to choose delay time and press [ (@B ] to confirm Hang Up (available in Digital channel mode only) a: Digital channel contact selection b: Off: When launch should be launch with set up connector. c: 18~108; If in the time range receiver calling by current channel,It should be transmit by the receiver connector. Over the set up time have not transmitted or on receiving, It should be by set up connector. . Press [(ZB ] to menu mode. . Press [@¥ or @@BJ to Main Set, press [@ZD ] to selection. . Press [@¥ or @@BJ to hang up calling, press [@ZB ] to selection. Press [@) or @@BJ to choose time or off, press [ZD ] to contirm > en o Tx. Channel a: EDIT: Transmit by current working channel b: BUSY 18~108: Transmit by receive the signal‘s channel, over the setting time will be transmit by working channel. 1. Press [@@D ] to menu mode. 2. Press [@ or @@B] to Main Set, press [ @® ] to selection 3. Press [@) or @@B] to Tx.channel, press [ @@D ] to selection 4. Press [ @¥) or @@BJ to required message, then press [@D] to selection. Key Define a : Key setting by long & short press function b : Short press [@D] to change side key 1, side key 2 for short & long selection 1. Press [@@B ] to menu mode. 2. Press [@) or @@] to Main Set, press [ & ] to selection. 3. Press [@) or @@B] to key detine, press [( ] to selection 4. Press [@¥ or @@B] to select, press [(@B ] to confirm. BackLight 1. Press [@ZD ] to menu mode. 2. Press [@%) or @@B] to Main Set, press [ (ZB ] to selection 3. Press [@) or @@B] to backlight, press [ @ZB ] to selection. 4. Screen shows Cont, 18/28/38 etc, then press [@D] to be Cont, the background will not close. If option 18/28/38 etc then the screen will be close in the corresponding time without any operation Beep If you need, you can activate and close i. 1. Press {@ZB ] to menu mode 2. Press [@ or @@] to Main Set, press [ B ] to selection 3. Press [@%) or @] to beep, press [@@B] to selection. 4. Press [@% or @@B] to select off or on, press [ B ] to contirm KeyLock You can lock the keypad so that prevent the keypad input, contained manual or auto, the self—motion would be lock without any operation 1. Press [@B] to menu mode. 2. Press [@¥ or @@B] to Main Set, press [ B ] to selection. 3. Press [@¥ or @@BJ to Keylock, press [ B ] to selection 4. Press [@ or @@B] to choose manual or auto, press [@@® ] to confirm. 5. Press [@BD] to choose lock keypad or unlock. CH—Mode a : FREQ: Frequency+ channel number b : NAME: Channel name. c : C H: Channel mode Press [@ZD] to menu mode. 1. Press [@%) or @@B] to Main Set, press [ @B] to selection. 2. Press [@¥ or @@B] to CH—mode, press [ &D ] to selection. 3. Press [@¥) or @BJ to select, press [@ZB ] to contirm Scan Mode a : TO : Time operation mode b : CO: Carrier operation mode. c: SE : Search operation mode. 1. Press [@ZB] to menu mode. 2. Press [@¥ or @@B] to Main Set, press [ B ] to selection 3. Press [ @% or @B] to channel scan mode ,Press [ B ] to selection 4. Press [ @ or @@B1 to choice, Press [ @IB ] to contirm Save Ch The parameters set in the current band are stored in the channel you want to save Input the digital directly to choice the channel. CH before the channel no. indicate that current channels have data. Press [@B ] to menu mode . Press [ @ or @@BJ to Main Set, press [@B ] to selection . Press [ @ or @@BJ to save.CH, press [ @D] to selection Press [ @M or §@B] to choose or input required channel number by keypad, press [@D ) to contirm & on —a 0 5 o Delete Ch a : CH before the channel no. indicate that current channels have data. b : Input the digital directly to choice the channel 1. Press [@ZD ] to menu mode 2. Press [@% or @@B] to Main Set, press [ (@B ] to selection 3. Press [@% or @@B] to delete.CH, press [@B ] to selection 4. Press [ @ or §@B] to choice required delete channel no. press [@@B] to contirm Roger Start this function will be appeared voice prompts after finishing transmit. The function is effective in analog channel mode an 1. 2. 3. Press [&B ] to menu mode. Press [@¥) or @@BJ to Main Set, press [ &D ] to selection Press [@B¥) or @@B1 to roger, Press [@B ] to selection. Press [@¥) or @@BJ to choose off or on, press [( ] to contirm Time 1. 2. 4. s. Press [@ZD] to menu mode. Press [@B) or @B] to Main Set, press [ &D ] to selection Press [@¥) or @@BJ to time, press [ &D ] to selection Press [@ZD ] to move place, press [@) or @@BJ to choose and change Press [@ZD] to confirm. Voice Tail s ons o 5 : OFF means do not decode sound tail code, ON mean decode sound tail code. We suggest ON Programming software [ Set ting ] has option tail code, option 54.7Hz. : This function is effective in analog channel mode only. Press [@ZD] to menu mode. Press [@¥) or @@B] to Main Set, press [ @@B] to selection Press [@ or @@BJ to VoiceTail, press [@ZD ] to selection Press [@) or @@BJ to choose off or on, press [@@P] to contirm Two. Channel Setting (Band A Set and Band B Set) NO. | Screen Display Settings Menu Introduction 01 Zone All Channels/Zone1...256 Zone Select 02 Step 2.5K/SKI...25K Frequency Step Setting 03 Power Low/Middle/High Transmit Power 04 Vox OFFION VOX Switch 05 Vox Level 1L2L...IL VOX Levels 06 WiN Narrow/Wide Wide/Narrow Band Select 07 TOT OFF/5S/30S!...6008 Time—out Timer 08 C—cDC OFF/G2.5167... 7541 CTCSSIDCS 09 RCDC OFFIG2.5167... 7541 RCDC 10 T—CDC OFF/G2.5167... 7541 T—cDC 11 Ch.Name —1A Channel Name Edit 12 Busy Lock OFF/ICode?...Impolite _ | Busy Lock(Transmit Permission) 13 Shift Up OFFIPlus/Minus Frequency Difference Direction 14 Shift Freq 0.000—99.000MHz Frequency Difference 15 Color Code 0/1...15 Color Code 16 | EncryptType OFF/Enhanced/Normal Encryption Type 17 Encrypt No 1221...16 Encryption Numbers ast NO. | Screen Display Settings Menu Introduction 18 DMR Mode Direct/Repeater/Double Slot Working Modes 19 DMR Slot Slot 1/Slot 2 Time Siot Select 20 Promiscuous OFFION Cancel Receiving Group Call List 21 RadioID Radio ID Select 22 Contacts Contacts Select 23 Ra List Receiving Group List Zone Select 1. Press [@D] to enter the menu. 2. Press [@¥ or @@B] key to channe! setting, then press [ (@P ] to select. 3. Press [@ or @@B] key to zone selection, then press [@ZD] to select 4. Press [@¥ or @@B] key to select, then press [ @@B ] to confirm Frequency Step Setting 1. Press [@D] to enter the menu. 2. Press [@) or @@B] key to channel setting, then press [@@B ] to select 3. Press [@¥ or @@B] key to frequency step setting, then press [@RD] to select 4. Press [@¥ or @@B] key to select, then press [@@B to confirm. Transmit Power You can set radio transmit power at HIGH, MIDDLE OR LOW, According to pre—programmed HIGH, MIDDLE or LOW power select key, change HIGH, MIDDLE or LOW power, using menu function, 1. Press [@B] to enter the menu 2. Press [@¥) or @@B] key to channel setting, then press [ (@P to select 3. Press [@) or @B] key to frequency step setting, then press [@ZB ] to select. 4. Press [@ or @@B] key to select, then press [ @ZB ] to contirm VOX Switch This function allows you transmit a hands—free voice call at a pre—programmed radio. Whenever the voice is detected by the microphone which is on the VOX function part, radio will automatically transmit signals during the pre—programmed time. 1. Press [@B] to enter the menu. 2. Press [@ or @@B] key to channel setting, then press [ @B ] to select 3. Press [@ or @@B] key to VOX Switch, then press [ &D ) to select 4. Press [@¥) or @@BJ key to select, then press [ (ZB ] to confirm VOX Level This function allows you transmit a hands—free voice call at a pre—programmed radio. Whenever the voice is detected by the microphone which is on the VOX function part, radio will automatically transmit signals during the pre—programmed time 1. Press [@B] to enter the menu. 2. Press [@¥ or @@B] to channel setting, then press [ &D to select. 3. Press [@% or @@B] key to VOX Level, then press [ @D] to select 4. Press [@¥) or @@BJ key to select, then press [ @@R ] to contirm an Wide / Narrow Band Select 1. Press [@D] to enter the menu 2. Press [@) or @@B] to channel setting, then press [ B ] to select. 3. Press [@) or @@B] key to Wide / Narrow Band Select, then press [ @@P] to select. 4. Press [@) or @@B] key to select, then press [@@D ] to contirm 5. This function can be only available under analog mode Time—out Timer (TOT) Select 158/308....6008 means transmitting time is 158/308....6008... If exceed this time, radio will stop transmitting automatically. Select OFF means set non—limit transmitting time, until PTT key are released and stop transmitting 1. Press [@D] to enter the menu. 2. Press [@¥ or @@B] to channel setting, then press [ @ZB ] to select. 3. Press [@%) or @@B] key to Time—out Timer setting, then press [ @B] to select. 4. Press [@ or @@B] key to select, then press [@@B ] to confirm CTCSS/DCS A: Only analog mode can set CTCSS/DCS B: It is both available that set receiving and transmitting at the same time C: Press [@ZD] key to change CTCSS, DCS positive direction, DCS negative direction, close CTCSS/DCS. 1. Press [@ZD ] to enter the menu 2. Press [@ or @@B] to channe! setting, then press [ EB ) to select 3. Press [@) or @@B] key to CTCSS /DCS , then press [ (@B ) to select. in 4. Press [@D] to change CTCSS / DCS frequency, then press [@¥) or @@BJ to select CTCSS/DCS frequency 5. Press [@B] to confirm R—CDC a: Only analog mode can set CTCSS/DCS. b: Only set receiving is available. : Press [@D] key to change CTCSS, DCS positive direction, DCS negative direction, close CTCSsS/DCS 1. Press [@D] to enter the menu. 2. Press [@) or @@B] to channel setting, then press [ (@B ] to select. 3. Press [@%) or @@B] key to R—CDC, then press [@@D ] to select 4. Press [@ZB ] to change CTCSS / DCS frequency, then press [@B%) or @@B J to select CTCSS/DCS frequency. Press [ ] to contirm T—opc a: Only analog mode can set CTCSS/DCS: b: Only set transmitting is available. : Press [@D ] key to change CTCSS, DCS positive direction, DCS negative direction, close CTCSS/DCS 1. Press [ @ZD] to enter the menu. 2. Press [@) or @@] to channel setting, then press [ B to select 3. Press [@) or @B] key to T—CDC, then press [ @ZB] to select 4. Press [ @ZD] to change CTCSS/DCS frequency, then press [@) or @@B] to select CTCSS/DGS frequency. 5. Press [@ZB ] to confirm «91 Channel Name Edit Press [ &D ] to enter the menu Press [@ or @@B] to channel setting, then press [@@® ] to select Press [@¥ or @@B] key to Channe! Name Edit, then press [ @B ] to select. Press number keys to input, and press [@) or @@B) key to move position Press [@B ] to confirm This function is only available under channel mode. 0 a s o n — Busy Channel Lockout (BCL) Set BCL under analog mode. OFF: not forbid to transmit. Wave: if earry wave then forbid to transmit. =Code: If CTCSS/DCS codes are match, then forbid to transmit Code: If CTCSS/DCS codes are not match, then forbid to transmit Set BCL under digital mode. Forbid: transmit is not allowed Impolite: transmit impolite(transmit at any time) Polite CC: If color codes are same, then forbid to transmit Polite ALL: if carry wave then forbid to transmit 1. Press [@D ] to enter the menu. 2. Press [@) or @@B] to channe! setting, then press [ @ZB ] to select 3. Press [@) or @@B] key to Busy Lock, then press [ B ) to select. 4. Press [@) or @@B] key to select, then press [ @@B ) to contirm Frequency Difference Direction 1. Press [@D] to enter the menu 2. Press [@%) or @@B] to channel setting, then press [ B ] to select 3. Press [@) or @@B] key to Frequency Difference Direction, then press [@B] to select. 4. Press [@) or @@B] key to select, then press [( ] to contirm 5. This function is only available under frequency mode Frequency Difference 1. Press [@B ] to enter the menu. 2. Press [@%) or @@B] to channel setting, then press [ B ] to select 3. Press [@%) or @@B] key to Frequency Difference, then press [ B to select 4. Press [@¥ or @@B] key to select, then press [ @ZIB ] to contirm Color Code a: Only digital mode can set color code, or it is not allowed to use radio. b: Only same color code to communicate 1. Press [@B] to enter the menu. 2. Press [@) or @@B] to channe! setting, then press [ @@B ] to select. 3. Press [@) or @@B] key to Color Code, then press [ @ZB ] to select 4. Press [@¥ or @@BJ to select, then press [@ZRB ] to confirm Encryption Type Only digital mode can set encryption Ithas normal encryption and enhanced encryption 2 types. Press [@ZD] to enter the menu. Press [@ or @@BJ to channel setting, then press [@B] to select. Press [@¥ or @@B] key to Encryption Type, then press [ @ZB ] to select Press [@¥ or @@BJ to select, then press [@B] to confirm. > ® N og e Encryption Numbers a: Encryption can be only set under digital channel b: Communication is available only the encryption type and encryption numbers are same. . Press [@ZB] to enter the menu. Press [@¥ or @@B] to channel setting, then press [@B ] to select . Press [@¥ or @@B] key to Encryption Numbers, then press [(&B ] to select . Press [@ or @@BJ to select, then press [@B ] to confirm. »ern s Working Modes There are 3 modes: Direct Mode, Repeater Mode, Real Double Time Slots Mode : Direct Mode Repeater Mode Real Double Time Slots Mode Press [@ZD] to enter the menu. Press [@% or @@B] to channel setting, then press [@B ] to select Press [@¥) or @@B] key to Encryption Numbers, then press [ (@B ] to select Press [@%) or @@BJ to select, then press {&ZB ] to contirm. This function can be only edited under digital channel. a s en ces Time Slots Selection If real double time slots are activated, radio must be set in a same time slot then communication can be available 1. Press [@D] to enter the menu 2. Press [@¥ or @@B] to channe! setting, then press [ B ] to select. 3. Press [@¥) or @@B] key to Time Slots Selection, then press [EB ] to select 187 4. Press [@%) or @@BJ to select, then press [( ] to contirm. 5. This function can be only edited under digital channel. Cancel Receiving Group Call List a: when it is on, it means communication is available when receiving any contact b: When itis OFF, it means communication is available only when the contacts that received must be in receiving group list first . Press [@D] to enter the menu. Press [@ or @@B] to channel setting, then press [ B ] to select Press [@) or @B] key to Cancel Receiving Group Call List, then press [@ZB ] to select. 4. Press [@ or @@BJ to select, then press [@B] to confirm. 5. This function can be only edited under digital channel e n o Radio ID Selection Change to select the ready radio ID 1. Press [@D] to enter the menu. 2. Press [@) or @B] key to channel setting, then press [@@B)] to select 3. Press [@) or @@B] key to radio ID selection, then press [ @@B] to select 4. Press [@¥) or @@B] key to select, then press [ @RB ] to confirm 5. This function can be only programmed under digital channels. Contacts Selection a; You can press upper and down keys to select contacts or input manually. b: If the contacts that you input is not exist, radio will automatically find adjacent valid contacts c: Itcan be set from [@ZB] C.1: Save: Save all the selected transmitted contacts. C.2: Local: Change the contacts from address list, and reset the required contacts C.3:; Priority: Change the priority contacts, and reset the required contacts C.4: OFF: Close transmitted contacts, transmitting is not allowed. 1. Press [@B ) to enter the menu. 2. Press [@) or @@B] key to channel setting, then press [ (ZB ] to select 3. Press [@%) or @@B] key to contacts selection, then press [ @@D] to select. 4. Press [@%) or @@B] key to select, then press [@@B ] to contirm 5. This function can be only programmed under digital channels. Receiving Groups List a; You can press up and down keys to select contacts or input manually. b: If the contacts that you input is not exist, radio will automatically find adjacent valid contacts. c: It can be set from [@ZD] C.1: Add(Priority): Add priority contacts C.2: Add(Local): Add contacts on the address list C.3: Delete: Delete the contacts C.4: Detail: View the contacts 1. Press [@D] to enter the menu. 2. Press [@) or @@B] key to channel setting, then press [ EB ] to select 3. Press [@%) or @@D] key to receiving group lists, then press [ @@D ] to select 4. Press [@ZD] key . and press [@%) or @@B] key to select, then press [ @IB ] to confirm 5. This function can be only programmed under digital channels.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Modify Date : 2019:01:28 15:03:03+08:00 Create Date : 2019:01:28 15:02:55+08:00 Metadata Date : 2019:01:28 15:03:03+08:00 Creator Tool : CorelDRAW Format : application/pdf Title : 转曲 HD1 英文说明书数字机 Creator : Administrator Document ID : uuid:5fcf5b5d-69d7-4c69-b5a3-a7d22319abe8 Instance ID : uuid:92ce7387-fefa-4461-a295-2063d8f46c31 Producer : Corel PDF Engine Version 14.0.0.701 Page Count : 13 Author : AdministratorEXIF Metadata provided by EXIF.tools