HES 3026006.002, Pages 1 4 Rev B 9400 Series Installation Guide 9500 9600Installation Instructions

User Manual: HES HES 9400 Series Installation Guide Installation Guide

Open the PDF directly: View PDF .
Page Count: 2

9400 / 9500 / 9600 Series Electric Strikes

Installation Instructions

HES, Inc.

Phoenix, AZ

800-626-7590

www.hesinnovations.com

1

Electrical Specifications

Minimum Wire Gauge Requirements

(Based on Round Trip)

Solenoid Voltage

12 VDC 24 VDC

200 feet or less

200 – 300 feet

300 – 400 feet

18 gauge

16 gauge

16 gauge

22 gauge

22 gauge

20 gauge

3

5

ASSA ABLOY, the global leader

in door opening solutions

Product Components

#10-32 & 10-24 Lockdown Screws (optional)

1

2

9400 / 9500 / 9600 Electric Strike Body

9400 / 9500 / 9600 Cover

4

Electrical Ratings for Solenoid

Continuous Duty 12 VDC

24

.50

24 VDC

96

.25

Resistance in Ohms

Amps

Solenoids are rated at +/- 10% indicated value.

4

4

Frame Preparation

9"

[228.6]

Centerline of Latchbolt

This edge toward door

2X Mounting Hole

Locations for

1/4-20 UNC Mounting Screws

7/8"

[22.5]

4-1/8"

[104.8]

1-3/4"

[44.5]

Clearance for

Power Wiring

Final Lockdown Feature

10-32 UNF or 10-24 UNC Screw (optional)

1-1/16"

[27.0]

4-1/8"

[104.8]

4X

[33.3]

1-5/16"

[33.3]

1-5/16"

1. LOOSEN the two 1/4”-20 x 1“ mounting screws.

2. ADJUST strike to appropriate horizontal position.

3. TIGHTEN the two 1/4”-20 x 1“ mounting screws.

4. LOCK DOWN adjustment by tightening the set screws.

Inches [mm]

3/4” [19]

Clearance for

LBM/LBSM Wiring

1/2” [12.7]

© 2014, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.

3026006.002 rev B

12

7

Lockdown

Screw

(optional)

Set Screw

Location

Set Screw

Location

Mounting

Screw

Mounting

Screw

ATTACH the cover using the #6-32 x 1/4” Cover Screws.

5

6

#6-32 x 1/4” Cover Screws

5/64” Hex Key

7

12-Volt and 24-Volt Pigtails

6

1/4”-20 x 1” Mounting Screws

3

Deadlatch Vertical Alignment

Note: May not be to

scale. For easy installation,

the template should be

ordered.

Adjusting Horizontal and Lockdown

Installing the Cover

5. INSTALL the #10-32 UNF or 10-24 UNC lockdown

screw (optional).

7/8”

[22.5]

Diagram 1: Product Components

2

Installation

Note: For 12 VDC, the Plug In Connector (pigtail)

marked “12 VDC” should be used; for 24 VDC, the

pigtail marked “24 VDC should be used.

1. SELECT the appropriate pigtail that matches system

power and electrically CONNECT as illustrated in

Diagram 2.

2. If no connector is present, CONFIGURE the wires as

illustrated in Diagram 2.

3. If using the Latchbolt Monitor (LBM) or Latchbolt

Strike Monitor (LBSM), REFER to Diagrams 3 and 4 on

Page 3 to complete wiring.

Note: The 9400/9500/9600 ships in FAIL SECURE

OPERATION mode.

4. USE Diagrams 5 and 6 on Page 3 as a guide to

convert 9400/9500/9600 to FAIL SAFE OPERATION, if

needed.

CAUTION!

Before connecting any device at the installation site, verify input voltage using a multimeter.

Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding

10% of the solenoid rating may cause severe damage to the unit and will void the warranty.

Note: When using a Corbin Russwin Series 5000 or

Yale 7000 series equipped with an offset deadlatch,

the deadlatch is located just above the Deadlatch

Vertical Alignment line as shown on the Installation

Template on Page 4.

5. PREPARE the door jamb using the Installation

Template located on Page 4 (with the exception of

the hole for final lockdown).

3

Installation (continued)

LBM Wiring

White

Orange Normally Open

Green Normally Closed

Common

Normally Open

Yellow Normally Closed

DIAGRAM 5: CYLINDRICAL LOCKSETS

LBSM Wiring

Brown

Blue Normally Open

Yellow Normally Closed

Common

Note 1: The 9400/9500/9600 series Electric

Strikes are pre-set for FAIL SECURE OPERATION

as shown in Diagram 5.

Note 2: There are Selector Stop Pins, one on

the left side and one on the right side. Both

Selector Stop Pins must be repositioned to

convert the strike to FAIL SAFE OPERATION.

1. To convert to FAIL SAFE OPERATION,

REMOVE the Selector Stop Pins on each side of

the strike body using the 5/64” hex key

provided.

2. MOVE the Selector Stop Pins to the FAIL

SAFE OPERATION position as pictured

(towards the center of the strike) in

Diagram 6.

3. TIGHTEN both Selector Stop Pins after they

have been moved to the FAIL SAFE OPERATION

position using the 5/64” hex key.

Note: Both keepers should be unlocked

without power, but lock when power is

applied.

4. VERIFY that both keepers are in FAIL SAFE

OPERATION.

Diagram 6: FAIL SAFE OPERATION

Diagram 5: FAIL SECURE OPERATION

Selector Stop

Pin Location

Selector Stop

Pin Location

Brown

Blue

Yellow

White

Orange

Green

RED

RED/GREEN

BLACK

VIOLET

RED

BLACK

VIOLET

RED/GREEN

IF CONNECTOR IS MISSING

(+ 12 VDC)

(-NEG)

(+ 24 VDC)

(-NEG)

or

Electric

Strike

Electric

Strike

CONNECT

TOGETHER

CONNECT

TOGETHER

CONNECT

TOGETHER

6. Electrically CONNECT the 9400/9500/9600 to the

Plug In Connector, and ATTACH the electric strike to

the jamb using the 1/4”-20 x 1“ mounting screws

provided.

7. CHECK latchbolt interaction to determine if hori-

zontal adjustment is needed, and ADJUST as needed.

LOCK DOWN the horizontal adjustment using the

#10-32 set screws as illustrated on Page 4.

8. OPTIONAL LOCKDOWN FEATURE: INSTALL the

#10-24 UNC or 10-32 UNF lockdown screw if

additional security is required. REMOVE the strike

before drilling hole.

9. INSTALL the cover plate, and FIX in place using the

#6-32 x 1/4” Cover Screws as illustrated on Page 4.

Preparing the Strike

Finishing the Installation

Preparing the Frame

Converting the Operation ModeConverting the Operation Mode

Diagram 3: Latchbolt Monitor Diagram 4: Latchbolt Strike Monitor

Verifying the Operation Mode

Diagram 2: 12V to 24V Conversion