HES 3062006.005__REV C__Pages 1 And 4 1006 Series Installation Guide (Dec. 2012 Present) HES1006Install Instructions3062006.005REVC
User Manual: HES HES 1006 Series Installation Guide (Dec. 2012 - Present) Installation Guide
Open the PDF directly: View PDF 
.
Page Count: 2
1006 Electric Strike Body
Trim Enhancer (with screws)
1006 Series Electric Strike
Installation Instructions
HES, Inc.
Phoenix, AZ
800-626-7590
www.hesinnovations.com
1
Product Components
Electrical Specifications
ELECTRICAL RATINGS FOR SOLENOID MINIMUM WIRE GAUGE REQUIREMENTS (One Way)
SOLENOID VOLTAGE
CONTINUOUS DUTY 12 VDC 12 VDC
25
.48
24 VDC 24 VDC
100
.24
Resistance in Ohms
Amps
Solenoids are rated at +/- 10% indicated value.
200 feet or less
200 - 300 feet
300 - 400 feet
18 gauge
16 gauge
14 gauge
18 gauge
18 gauge
16 gauge
12 & 24 Volt Pigtails
Keeper Shims (2, with screws)
1
2
2
3
4
3
4
4
Faceplate Options Inches [Millimeters]
5/32
[3.97]
3-1/8”
[79.37]
23/32”
[18.26]
3-1/8”
[79.37]
7/8”
[22.23]
2-7/8”
[73.02]
1-9/64”
[28.83]
1/8”
[3.17]
1-11/32”
[34.11]
23/32”
[18.22]
1-1/16”
[26.72]
29/32”
[23.39] 1-11/32”
[34.11]
27/32”
[21.46] 27/32”
[21.46]
23/32”
[18.22]
19/32”
[15.46] 1-15/32”
[37.29]
1-3/32”
[27.81]
5/16”
[7.79]
1-23/32”
[43.64]
1-37/64”
[40.08]
AD, HD, ND & TD A, H, HT, N & T AM, HM, & NM
KD KR
KM Z J, E
(4-7/8” x 1-1/4” SQUARE CORNER)
1-15/32”
[37.29]
1-25/64”
[35.48]
1-3/4”
[44.45]
3062006.005 rev C
© 2015, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.
C
L= center line of faceplate
(2nd line = center line of faceplate opening)
“
ASSA ABLOY, the global leader
in door opening solutions
1
2
1006 WITH CYLINDRICAL LOCKSETS
3
Installation Directions
NOTE: Cutout templates are detailed on Page 3 and faceplate
options are detailed on Page 4.
4. PREPARE the frame using appropriate lockset template and
faceplate combination.
Preparing the Strike
CAUTION! Before connecting any device at the installation site, verify input voltage using a multimeter. Many
power supplies and low voltage transformers operate at higher levels than listed. Any input voltage exceeding
10% of the solenoid rating may cause severe damage to the unit and will void the warranty.
Preparing the Frame
LBSM WIRING
White
Orange Normally Open
Green Normally Closed
Common Brown
Blue Normally Open
Yellow Normally Closed
Common
Diagram 2. 12V to 24V Conversion
Brown
Blue
Yellow
White
Orange
Green
Diagram 3. Latchbolt Monitor Diagram 4. Latchbolt Strike Monitor
BLACK
RED/GREEN
RED
VIOLET
VIOLET
RED/GREEN
BLACK
RED
IF CONNECTOR IS MISSING
(+ 12 VDC)
(-NEG)
(+ 24 VDC)
(-NEG)
ELECTRIC
STRIKE
ELECTRIC
STRIKE
CONNECT
TOGETHER
CONNECT
TOGETHER
CONNECT
TOGETHER
Finishing the Installation
5. ATTACH the electric strike to the jamb using the screws
provided with the faceplate option kit.
NOTE: For 12V DC, the pigtail marked “12 VDC” should be
used. For 24V DC, the pigtail marked “24 VDC”
should be used.
1. SELECT the appropriate Plug In Connector that matches
system power and electrically CONNECT as illustrated in
Diagram 2.
2. IF no connector is present,
THEN CONFIGURE the wires as illustrated in Diagram 2.
3. IF using the Latchbolt Monitor (LBM) or Latchbolt
Strike Monitor (LBSM),
THEN REFER to Diagrams 3
and 4 to complete wiring.
LBM WIRING
Cutout Templates
1006 WITH CYLINDRICAL LOCKSETS
2X 12-24
UNC THREADS
2X 12-24
UNC THREADS
1-11/16"
1-1/4"
1-11/16"
1-1/4"
5/32”
1-11/16"
9"
1-3/8"
1006 WITH MORTISE LOCKSETS
Inches [Millimeters]
4-7/8"
[123.83]
4-1/8"
[104.77]
[85.72]
3-3/8"
[42.86]
[31.8]
[42.86]
[85.72]
3-3/8"
[31.8]
4-1/8"
[104.77]
4-7/8"
[123.83]
[85.72]
3-3/8"
[42.86]
[34.92]
[228.6]
C
L
C
L
29/32”
[23.01]
19/32”
[15.08]
C
L
Strike
Prep
3/8"
4"
8"
1-1/4"
1-3/4"
Vertical
Centerline
C
L
Lock
4-7/8"
4-1/8"
3-1/2"
5/8"
1-1/4"
Mortise
Lockset
C
L
Strike
C
L
Strike
Prep
5/8"
1-1/4"
Cylindrical
Lock
C
L
C
L
STRIKE
LOCK
Vertical
Centerline
2-1/4"
1-1/4"
1-3/4"
Please note the horizontal centerline of the electric strike
in relation to the centerline of the mortise lockset.
Please note the horizontal centerline of the electric strike
in relation to the centerline of the cylindrical lockset.
[203.2]
[101.6]
[44.45]
[31.8]
[9.53]
[15.88]
[31.8]
[88.9] [104.77] [123.83] [57.15]
[31.8]
[44.45]
[15.88]
[31.8]
3-1/2"
[88.9]
4-1/8"
[104.77]
4-7/8"
[123.83]
METAL JAMB INSTALLATION
FOR 1006 SERIES FACEPLATES
Cutout dimenstions for option faceplates:
J, K, KM, N, NM, A, AM, H, HM, HT, T, Z, R and E
NOTE: Normally used with mortise locks
without deadbolt. Not used with
Schlage L9000 or Yale 8700 series.
METAL JAMB INSTALLATION
FOR 1006 -D SERIES FACEPLATES
Cutout dimenstions for option faceplates:
KD, ND, AD, HD, HTD and TD
NOTE: Normally used with mortise locks
with deadbolt. Can be used with
Schlage L9000 or Yale 8700 series.
WOOD JAMB INSTALLATION
FOR 1006-2 SERIES FACEPLATES
Cutout dimenstions for option faceplates:
J2, K2, KM2, N2, T2, H2 AND A2
