HHC Changzhou CB11HHC002 Control Box User Manual CB11 Control Box Instructions V1

HHC Changzhou Corp. Control Box CB11 Control Box Instructions V1

User Manual

Download: HHC Changzhou CB11HHC002 Control Box User Manual CB11 Control Box Instructions V1
Mirror Download [FCC.gov]HHC Changzhou CB11HHC002 Control Box User Manual CB11 Control Box Instructions V1
Document ID2726383
Application ID+m8xvfIXPpT6ZV5kECW9DA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.75kB (471865 bits)
Date Submitted2015-08-26 00:00:00
Date Available2015-08-26 00:00:00
Creation Date2015-08-25 08:26:59
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2015-08-25 08:26:59
Document TitleMicrosoft Word - CB11 Control Box Instructions-V1
Document CreatorPScript5.dll Version 5.2.2
Document Author: jack.chen

CB11 Control Box Instructions
1. Product Overview
Product Name:
Control Box
Product Model No.: CB11
FCC ID:
2AEQWCB11HHC002
2. Environment requirement
Operation temperature: +10℃~ +40℃.
Storage temperature: -10℃~65℃.
Operating Humidity:10%~80%RH,non‐condensing.
Storage Humidity:10%~ 85%RH,non‐condensing.
3. Directions for Operation
To use the control box, the PSK2920A switch power supply must be connected as the control box
power supply. The CH11 remote control must also be paired to be used. Detailed usage for each
port is as follows:
3.1 Before use, the CH11 remote control and CB11 control box must be paired:
3.2 Then, turn on the control box's Power, and after the beep sound the system will work.
Follow the example below to properly plug parts in.
1/3
SYNC Cord
Connection
Head Motor Port
LED
Connection
USB
Connection
Power Input connection
Foot Motor Port
4. The port is introduced
4.1 “HD Motor”:Connects to the Head motor, and lifts/lowers head section.
4.2 “FT Motor”:Connects to the Foot motor, and lifts/lowers foot section.
4.3 “Power”:Connects to the power supply box, controls power supply.
4.4 “USB”:Connects to the USB adapter box, and USB adapter box and USB socket connection.
4.5 “LED”:Connects with lights.。
4.6. “SYN”:Same steps. Connect another control box, and two control boxes will synchronize.
5. Matters needing attention:
5.1 The function will only work normally in proper working power conditions.
5.2 Control box input voltage must be less than 29.2VDC.
5.3 The CH11 remote control is needed for proper control.
5.4 If problems are identified, they must be treated by professional personnel.
6. Additional attention for user:
6.1 This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
2/3
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/ TV technician for help.
6.2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
6.3 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. To maintain compliance with FCC RF exposure compliance requirements, please
using a minimum separation distance of 5 mm from the device.
This transmitter must not be co‐located or operating in conjunction with any other antenna
or transmitter.
6.4 For Intentional and unintentional radiators the manual shall caution the user that changes
or modifications not expressly approved by the party responsible for compliance could void the
users authority to operate the equipment
3/3

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jack.chen
Create Date                     : 2015:08:25 08:26:59+08:00
Modify Date                     : 2015:08:25 08:26:59+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - CB11 Control Box Instructions-V1
Creator                         : jack.chen
Document ID                     : uuid:83f52d57-0267-4284-b34e-3856138bc24c
Instance ID                     : uuid:ed17c30a-43b0-4787-8888-b744de6d1c40
Page Count                      : 3
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AEQWCB11HHC002

Navigation menu