HMD global TA-1035 Smart Phone User Manual

1. Insert the SIM and memory

card

1.With the phone facing down, put your fingernail in

the small recess located on the bottom edge.

2.Bend the cover open and remove it.

3.Slide the nano-SIM card into the SIM slot with the

metal contact area down until it locks into place. If

you have a dual-SIM phone, insert the second SIM

into the SIM2 slot until it locks into place.

Use only original nano-SIM cards. Use of incompati-

and may corrupt data stored on the card.

the phone on

Plug a compatible charger into a wall outlet, and

connect the cable to your phone. Your phone sup-

ports the USB micro-B cable. You can also charge

your phone from a computer with a USB cable, but

it may take a longer time.

If the battery is completely discharged, it may take

3. Learn more about your new

Nokia phone

For a printable user guide, online user guide, and

troubleshooting help, go to www.nokia.com/

phones.

1023 EN 1.0

Main camera

,

Product and Safety info

Important: We invite you to read the enclosed instructions before

installing your equipment. For valuable information on the safe use

of the device and battery, read the Product and safety info booklet

use of your device and battery, read the Product and safety info

booklet before you take your device into use.

You can only use your device on the GSM/GPRS/EDGE 850/900/

1800/1900; WCDMA 1/2/4/5/8; LTE 2/3/4/7/12/17/28/38/

not available, it is recommended that you change the highest

Settings > Mobile networks, and switch Preferred network type to

2G/3G.

For more info, contact your network service provider.

not attempt to remove the battery, as you may damage the device.

To replace the battery, take the device to the nearest authorised

service facility.

can connect to your device USB connector, may also be compatible.

Some of the accessories mentioned in this user guide, such as

charger, headset, or data cable, may be sold separately.

The surface of the device is nickel-free.

Theoretical talk time: Up to 23.49 hours.

Theoretical standby time: Up to 24 days (display off)

Use only compatible memory cards approved for use with this device.

Incompatible cards may damage the card and the device and corrupt

data stored on the card.

Note: Pre-installed system software and apps use a significant

This mobile device meets guidelines for exposure to radio waves as

set forth by the Council of Europe (CE) and the Federal

Communications Commission (FCC). Refer to the following.

Your mobile device is a radio transmitter and receiver. It is designed

not to exceed the limits for exposure to radio waves recommended

by international guidelines. These guidelines were developed by the

independent scientific organization ICNIRP and include safety

margins designed to assure the protection of all persons, regardless

of age and health. The guidelines use a unit of measurement known

For electronic safety, maintain the separation distance with

accessories containing no metal, that position handset a minimum of

the above distance. Use of other accessories may not ensure

compliance with RF exposure guidelines.

for testing.

Your handset is a radio transmitter and receiver. It is designed and

manufactured not to exceed the emission limits for exposure to

radio frequency (RF) energy set by the Federal Communications

measurement known as the Specific Absorption Rate, or SAR. The

SAR limit set by the FCC is 1.6 W/kg. The tests are performed in

positions and locations (e.g. at the ear and worn on the body) as

required by the FCC for each model. The highest SAR value for this

is x.xxx W/kg, and when worn on the body in a holder or carry case, is

x.xxx W/kg.

Body-worn Operation; This device was tested for typical body-worn

operations with the handset kept 1.5 cm from the body. To maintain

compliance with FCC RF exposure requirements, use accessories that

maintain a 1.5 cm separation distance between the user’s body and

emission guidelines. SAR information on this model handset is on file

with the FCC and can be found under the Display Grant section of

www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1035 and

FCC ID 2AJOTTA-1023.

Additional information on Specific Absorption Rates (SAR) can be

found on the FCC website at www.fcc.gov/general/radio-frequency-

safety-0.

To send data or messages, a good connection to the network is

needed. Sending may be delayed until such a connection is available.

Follow the separation distance instructions until the sending is

harmful interference, and (2) this device must accept any

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

• Reorient or relocate the receiving antenna.

Naucalpan de Juárez

Edo de México

CP 53330

RFC: GCE1410146Y9

LTE Band 3 23 dBm

,