HON HAI PRECISION IND J20H077 Bluetooth Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2025542
Application ID	KbKtMNC36uLpNOAbB9prkg==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	68.37kB (854639 bits)
Date Submitted	2013-07-25 00:00:00
Date Available	2013-08-05 00:00:00
Creation Date	2013-07-24 15:02:51
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2013-07-24 15:03:03
Document Title	Microsoft Word - User manual for J20H070.00 Bluetooth1025.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	RD

COMPANY CONFIDENTIAL
User Manual
Bluetooth Module
Part Name
Bluetooth Module
Doc. Rev.
Foxconn P/N.
Prepared by
Kevin Tao
0.0
J20H077.00
Reviewed by
Eddie Huang
Approved by
COMPANY CONFIDENTIAL
Content
Section1 Introduction ..............................................................................................................3
1. Product Overview ................................................................................................................3
1.1 Application scope..................................................................................................... 3
1.2 Block Diagram.......................................................................................................... 3
1.3 Features .................................................................................................................... 4
1.4 Interface and Connector ......................................................................................... 4
2. Electrical Specification ........................................................................................................5
2.1 Recommended operating rating............................................................................ 5
2.2 DC Characteristics .................................................................................................. 5
2.3 ESD Information ...................................................................................................... 5
2.4 Environment Storage Condition ............................................................................ 5
3. RF Specification ...................................................................................................................6
3.1 Bluetooth 3.0 ............................................................................................................ 6
3.2 Antenna Characteristic............................................................................................ 7
4. Mechanical Specifications ...................................................................................................8
4.1 PCB Assembly Dimension ..................................................................................... 8
Section2 WinXP utility and install .........................................................................................9
5. Overview ...............................................................................................................................9
6. Requirements........................................................................................................................9
7. USB to UART Interface Driver Install ..............................................................................9
8. Test Tool Install .................................................................................................................11
8.1 ActivePerl-5[1].8.4.810-MSWin32-x86.msi install............................................. 11
8.2 dotnetfx.exe install................................................................................................. 12
8.3 setup_for 20702A1.exe ........................................................................................ 12
9. Blue Tool Test Setting ........................................................................................................14
9.1 Tx Mode .................................................................................................................. 14
9.2 Rx Mode.................................................................................................................. 19
COMPANY CONFIDENTIAL
Section1 Introduction
1. Product Overview
The J20H077.00 Bluetooth module provides Bluetooth 3.0 compliant wireless modem
function. This module is based on BCM20705 solution which is integrated 2.4GHz
transceiver and manufactured using the industry’s most advanced 65nm CMOS
low-power process.
1.1 Application scope
The BT Module is compliant to Bluetooth 3.0 and EDR standard:
Carrier Frequency: 2402MHz ~ 2480 MHz
Carrier Spacing: 1.0MHz
Duplexing: TDD
Modulation: FHSS
GFSK, pi/4-DQPSK, 8DPSK
Symbol Rate: 1Mbps (GFSK), 2Mbps (pi/4-DQPSK), 3Mbps (8DPSK)
This module is designed with BTB connector and UART Interface, and it is
installed as a client device in TV platform.
1.2 Block Diagram
The general HW architecture is shown below Figure:
COMPANY CONFIDENTIAL
1.3 Features
Bluetooth 3.0 Compliant
UART Interface.
Module is powered by the host with a 3.3V +/- 10% supply.
One PCB printed antenna.
4 layers through hole PCB design with halogen free FR4 material
1.4 Interface and Connector
i Pin definition:
Pin Number
Symbol Name
Status
Pin definition
Ground
GND
UARTTXD
UART Transimit
UARTRXD
UART Receive
GND
Ground
BT_RST
BT Reset
BT_DEVICE_WAKE
BT wake up Signal
BT_HOST_WAKE
Host wake up Signal
EMT_SYNC
GND
Ground
10
VDD_3P3
Power
S1
GND
Ground
S2
GND
Ground
COMPANY CONFIDENTIAL
2. Electrical Specification
2.1 Recommended operating rating
Element
Symbol
Min
Typ
Max
Unit
DC supply voltage
UV+
3.0
3.3
3.6
(V)
2.2 DC Characteristics
Parameter
Min
Typ
Max
Unit
Supply voltage
Tx Current
3.0
3.3
40
3.6
50
(V)
(mA)
Rx Current
Standby Current
26
32
(mA)
(mA)
Symbol
STBY3.3V
2.3 ESD Information
Mode
Level
Unit
HBM
MM
+/-1500
+/-200
2.4 Environment Storage Condition
Environment condition
Temperature
Humidity
Operating Temperature: -10 deg.C ~70 deg.C
Storage Temperature: -40 deg.C ~80 deg.C
Operating Humidity: 5% ~95% (Non-condensing)
Storage Humidity: 5% ~95% (Non-condensing)
COMPANY CONFIDENTIAL
3. RF Specification
3.1 Bluetooth 3.0
Items
Contents
Max.
Unit
dBm
-75
75
kHz
DH1
DH3
-20
-20
-4
-4
20
20
kHz/50us
kHz/50us
DH5
Average Drift
-20
-5
20
kHz/50us
DH1
-25
-1
25
DH3
-40
40
kHz
kHz
DH5
-40
40
F1avg
140
150
175
F2max
115
140
kHz
kHz
F1/F2 Ratio
5. EDR Relative Transmit Power
0.8
0.96
2Mbps: P[DQPSK]-P[GFSK]
-4
0.25
dB
3Mbps: P[8DPSK]-P[GFSK]
-4
0.25
Initial Frequency Error: i
-75
-3
75
Frequency Error: 0
Block Frequency Error: i + 0
-10
-75
-2
-5
10
75
RMS DEVM
0.05
0.2
Peak DEVM
0.12
0.35
99%
100%
Initial Frequency Error: i
-75
-9
75
Frequency Error: 0
-10
-1.5
10
Block Frequency Error: i + 0
-75
-10
75
RMS DEVM
0.05
0.13
Peak DEVM
0.13
0.25
99%
100%
- TX Characteristics -
Min.
Typ.
ʳ
1. Power Levels
BT Output Power (Basic Data Rate)
-1
2. Initial Carrier Frequency Tolerance
Average Offset
3. Carrier Drift
Drift Rate
kHz
4. Modulation Characteristic
dB
6. EDR Carrier Frequency Stability and Modulation Accuracy
2Mbps:±/4 DQPSK
99% DEVM (% Symbols <=0.3)
kHz
kHz
kHz
3Mbps:8DPSK
99% DEVM (% Symbols <=0.13)
kHz
kHz
kHz
COMPANY CONFIDENTIAL
Items
Specification
Frequency range
Data rate
- RX Characteristics 1. Minimum Input Level Sensitivity
GFSK (1Mbps)
±/4 DQPSK (2Mbps)
Contents
BT3.0
2.4GHz~2.4835GHz
1Mbps, 2Mbps, 3Mbps
Min.
Typ.
Max.
ʳ
ʳ
ʳ
-90
-83
-90
-83
8DPSK (3Mbps)
Unit
ʳ
dBm
dBm
-85
-77
dBm
ʳ
ʳ
ʳ
ʳ
GFSK (1Mbps)
-20
dBm
±/4 DQPSK (2Mbps)
-20
-14
dBm
8DPSK (3Mbps)
-20
-14
dBm
2. Maximum Input Level
3.2 Antenna Characteristic
Parameter
Value
Units
2402~2483.5
MHz
Antenna gain (max)
0.13
dBi
VSWR
<2.1
43% @2402MHz
44% @2441MHz
40% @2480MHz
Operating frequency range
Efficiency
COMPANY CONFIDENTIAL
4. Mechanical Specifications
4.1 PCB Assembly Dimension
Dimension (W x L ): 34.58mmx20mm
design
PCB: 4 layer HF-FR4
COMPANY CONFIDENTIAL
Section2 WinXP utility and install
5. Overview
This document is intended to provide a brief introduction to the Mckinley test for users.
It includes the initial setup instruction on how to configure the device and test the
transmitter.
6. Requirements
Hardware
- Desktop PC with USB interface
Software
- Windows XP Professional (SP3 or above)
- USB to UART DRIVER
- Bluetooth Test Tool
7. USB to UART Interface Driver Install
Step1: Go to “* \BT\Test Tool\uart driver\V6.5” and double click
“CP210x_VCP_Win_XP_S2K3_Vista_7.exe” to install USB to UART Interface driver.
COMPANY CONFIDENTIAL
Step2: Select “Launch the CP210x VCP Driver Installer”, and click the “Finish” button
to start the install.
Step3: Finish installation and Insert the Conversion Board with Module, you will get a
card named”Silicon Labs CP210x USB to UART Bridge” in computer management..
COMPANY CONFIDENTIAL
8. Test Tool Install
8.1 ActivePerl-5[1].8.4.810-MSWin32-x86.msi install
Step1: Go to “* \BT\Test Tool” and double click
“ActivePerl-5[1].8.4.810-MSWin32-x86.msi” to install
Step2: Select the default setting, and then click the “Next>” button to show the next
page.
Step3: Select ”Enable PPM3 to send profile info to ASPN ”, and then click the “Next>”
button to show the next page.
COMPANY CONFIDENTIAL
Step4: Select the default setting, and then click the “Next>” button to continue the
installation.
8.2 dotnetfx.exe install
Step1: Go to “* \BT\Test Tool” and double click “dotnetfx.exe” to install Microsoft.net
Framework 1.1
8.3 setup_for 20702A1.exe
Step1: Go to “* \BT\Test Tool” and double click “setup_for 20702A1.exe” to install
BlueTool
Step2: Select the “Typical”, and then click the “Next>” button to continue the
installation.
COMPANY CONFIDENTIAL
Step3: Click the “Finish” button to finish the installation.
COMPANY CONFIDENTIAL
9. Blue Tool Test Setting
9.1 Tx Mode
Step1: Go to “C:\Program Files\Broadcom\BlueTool “to double click the
“BlueTool.exe” to run Blue Tool
Step2: Select “View ->Log Window “to show the log window
COMPANY CONFIDENTIAL
Step3: Select “Transport ->HCI Control.. “to select the interface based on the
computer management.
COMPANY CONFIDENTIAL
Step4: Select “7.3: Host controller & Baseband Commands(3 Key) “ and do “Reset” .
Step5: Select “7.4: Informational Parameters(4 Key) “ and do “Read_BD_ADDR” to
read the MAC ID
COMPANY CONFIDENTIAL
Step6: Select “0: Verdor-specific Commands(0 Key) “ and do “Tx Test” to set Tx
Mode
Step7: Select “0: Verdor-specific Commands(0 Key) “ and do “Tx Test” to set Tx
Mode, set packet type DH5,output power 10dBm , then click “OK”
COMPANY CONFIDENTIAL
9.2 Frequency Deviation Test
Step1: Based on Section 9.1 Step5 , Select “0: Verdor-specific Commands(0 Key)
and do “Set Tx Carrier Frequency ARM” to set Frequency Deviation Test .
Step2: Select frequency for Frequency Deviation Test .
COMPANY CONFIDENTIAL
9.3 Rx Mode
Step1: Based on Section 4.1 Step5 , Select “0: Verdor-specific Commands(0 Key)
“ and do “write receive only” to set Rx Mode .
Step2: Set frequency , then click “OK”
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
This device is intended only for OEM integrators under the following
conditions:
The transmitter module may not be co-located with any other transmitter or
antenna.
As long as the conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID:MCLJ20H077”. The grantee's FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions
suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this
manual. The further RF exposure reduction can be achieved if the product can be kept
as far as possible from the user body or set the device to lower output power if such
function is available.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour
les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction
aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que
possible du corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie
la plus faible si une telle fonction est disponible.
This device is intended only for OEM integrators under the following conditions: (For
module device use)㩷
The transmitter module may not be co-located with any other transmitter or antenna.
As long as the conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.㩷
Tant que les le conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:㩷
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM
sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains
IC: 2878D-J20H077”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 2878D-J20H077".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiquͼ dans ce manuel.
For Taiwan ᤞ፿Κ
ᆖী‫ڤ‬ᎁᢞ‫ٽ‬௑հ‫פ܅‬෷୴᙮ሽᖲΔॺᆖ๺‫ױ‬Δֆ‫׹‬Ε೸ᇆࢨࠌ‫݁ृش‬լ൓ᖐ۞᧢‫ޓ‬᙮
෷Ε‫ף‬Օ‫פ‬෷ࢨ᧢‫଺ޓ‬๻ૠհ௽ࢤ֗‫פ‬౨Ζ
‫פ܅‬෷୴᙮ሽᖲհࠌ‫ش‬լ൓ᐙ᥼ଆ౰‫ڜ‬٤֗եឫ‫ٽ‬ऄຏॾΙᆖ࿇෼‫ڶ‬եឫ෼ွழΔᚨ‫م‬
‫ܛ‬ೖ‫ش‬Δࠀ‫ޏ‬࿳۟ྤեឫழֱ൓ᤉᥛࠌ‫ش‬Ζছႈ‫ٽ‬ऄຏॾΔਐࠉሽॾऄ๵ࡳ‫܂‬ᄐհྤᒵ
ሽຏॾΖ‫פ܅‬෷୴᙮ሽᖲႊ‫ٽ࠹ݴ‬ऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭‫ش‬ሽंᘿ୴ࢤሽᖲ๻ໂհ
եឫΖ
Note: 1. ‫ء‬ᑓิ࣍࠷൓ᎁᢞ৵ലࠉ๵ࡳ࣍ᑓิ‫᧯ء‬ᑑ‫ق‬ᐉ᧭‫ٽ‬௑ᑑ᧘ 2.
࣍ؓ‫؀‬Ղᑑ‫ق‬ψ‫ء‬ข঴փܶ୴᙮ᑓิ:
ߓอᐗ೸ᚨ
XXXyyyLPDzzzz-x (NCC ID) ω‫ڗ‬ᑌ.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:07:24 15:03:03+08:00
Create Date                     : 2013:07:24 15:02:51+08:00
Metadata Date                   : 2013:07:24 15:03:03+08:00
Format                          : application/pdf
Title                           : Microsoft Word - User manual for J20H070.00 Bluetooth1025.doc
Creator                         : RD
Document ID                     : uuid:249eb67f-77b0-4752-a668-0d04b4227e4d
Instance ID                     : uuid:ba259588-2187-4083-8683-6424b20a507d
Page Count                      : 24
Author                          : RD

EXIF Metadata provided by EXIF.tools