HON HAI PRECISION IND MICB WiFi 11a/n module User Manual MIC B user manual 0203
HON HAI Precision Ind. Co., Ltd. WiFi 11a/n module MIC B user manual 0203
User manual
Confidential 1
MIC-B
WIFI Module
User Manual
Rev. 0.1
Confidential 2
Reviewers
Review Dates
Department Name
Plan Results
Director of Engineering LianXi 2010.12.09 OK
Hardware Engineering FeiShan 2010.12.09 OK
Confidential 3
Table of Contents
1. INTRODUCTION ..................................................................................................................................................4
2. REGULATORY INFORMATION........................................................................................................................5
Confidential 4
1. Introduction
The MIC-B 802.11a /n module provides wireless modem
functionality utilizing OFDM technology. The objective of this use manual is
to verify the functionality of the MIC-B 802.11a/n module RF/Digital
electronic design against the design specifications.
This revision includes results taken at various temperatures (0℃,
25℃,65 ℃) and voltages (3.0V, 3.3V, 3.6V). Included are statements of
test purpose, test methodologies, test modes and parameters,
environmental conditions, applicable specifications, and typical reference
design performance.
The major specifications and documents are listed below and upon
to update in the following new revisions.
IEEE 802.11a/n
Confidential 5
2. Regulatory Information
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling
Hon Hai Precision WiFi 11a/n module MIC-B labeled as below.
FCC ID: MCLMICB
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not
visible when the module is installed into the system, “Contains FCC ID: MCLMICB” shall
be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
This device must not be co-located or operating in conjunction with any other antenna
or transmitter.
Caution: 5150 – 5250 MHz Device only
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz
frequency range.
Confidential 6
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of this device.
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropic radiated power (EIRP) is not more
than that required for successful communication.
Caution: 5150 – 5250 MHz Device only
Tthe device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS-102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained between the
antenna of this device and all persons. This device must not be co-located or operating
in conjunction with any other antenna or transmitter.
Labeling
Hon Hai Precision WiFi 11a/n module MIC-B labeled as below.
IC: 2878D-MICB
The proposed with IC ID label format is to be placed on the module. If IC ID is not
visible when the module is installed into the system, “Contains IC: 2878D-MICB” shall
be placed on the outside of final host system.