HON HAI PRECISION IND WINB3 Bluetooth Module 4.0 + EDR/LE User Manual WIN B3 Rev1 0

Download:
Mirror Download [FCC.gov]
Document ID	1429054
Application ID	mZIObd91iJX2ofX9cIWGWg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.2kB (102448 bits)
Date Submitted	2011-03-10 00:00:00
Date Available	2011-03-10 00:00:00
Creation Date	2011-03-04 14:58:35
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2011-03-10 10:08:11
Document Title	Microsoft Word - WIN-B3_User manual_Rev1.0.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Iver_Tao

COMPANY CONFIDENTIAL
WIN-B3
Bluetooth Module
User Manual
Rev. 1.01
Prepared by
Gallon Tao
Reviewed by
Approved by
COMPANY CONFIDENTIAL
Index
1. REVISION HISTORY...................................................................................................................................................3
2. INTRODUCTION ..........................................................................................................................................................4
3. PRODUCT SPECIFICATION .....................................................................................................................................5
4. PRODUCT REQUIREMENTS AND CHARACTERISTIC......................................................................................6
5. MECHANICAL DRAWING .........................................................................................................................................6
6. REGULATORY INFORMATION................................................................................................................................7
COMPANY CONFIDENTIAL
1. Revision History
Date
Change Note
REV
Note
2011-02-22
Initial Release
1.0
COMPANY CONFIDENTIAL
2. Introduction
Project Name: Bluetooth 4.0 +EDR(Low Energy support) module
This documentation describes the product specification of the Bluetooth 4.0 module.
It is a confidential document of Foxconn.
2.1 Scope
This Bluetooth module is available in the 2.4-GHz ISM band, it is compatible with
Bluetooth specification v4.0. It supports basic rate of 1Mbps with GFSK modulation,
and EDR 2Mbps for DQPSK and 3Mbps for 8DPSK, in addition, it supports Low
Energy function (LE GFSK).
2.2 Function
Class 2 specification RF output power (max +4 dBm @ average power)
Full piconet and scatternet operation
Supports 1Mbps basic rate, 2Mbps, 3Mbps Enhanced Data Rate, and Bluetooth Low
Energy (1Mbps).
USB 2.0 full-speed compliant interface
Full support for power saving modes
FW via on-line downloading and upgrade
COMPANY CONFIDENTIAL
3. Product Specification
3.1 Bluetooth RF Specification
Bluetooth Standards
v4.0 (Basic Rate + EDR + LE)
Operating Frequency
2.400 – 2.4835
Data Rate
Basic Rate: 1Mbps
Enhanced Data Rate: 2Mbps, 3Mbps
Low Energy: 1Mbps
GFSK(1Mbps); DQPSK(2Mbps), 8DPSK(3Mbps);
Modulation Schemes
LE GFSK(1Mbps)
Transmitter Output Power
Transmitter Output Power: -6dBm~ +4dBm (Class 2 Specification)
EDR Relative Transmit Power: (PGFSK-4dB) < PDPSK < (PGFSK+1dB)
Receiver Sensitivity
Typical -90dBm @1Mbps (PER<0.1%)
Typical -90dBm @2Mbps (PER<0.01%)
Typical -85dBm @3Mbps (PER<0.01%)
3.2 Electrical Specification
Absolute Maximum Ratings
These specification indicate levels where permanent damage to the device can occur. Functional
operation is not guaranteed under these conditions. Operation at absolute maximum conditions for
extended can adversely affect long-term reliability of the device.
Rating
Symbol
Value
Unit
DC supply voltage for the device
VDD
3.0~3.6
Recommended Operating Condition
Element
Symbol
Value
Minimum
DC supply voltage for the device
VDD
3.0
Typical
3.3
Unit
Maximum
3.6
Function operation is not guaranteed outside this limit, and operation outside this limit for extended
periods can adversely affect long-term reliability of the device.
Current Consumption
Idle: 6mA @3.3V
Transmit: 36mA @3.3V
Receive: 26mA @3.3V
COMPANY CONFIDENTIAL
4. Product Requirements and Characteristic
4.1 Hardware Characteristic
Form factor
Host Interface
PCB
Antenna &RF connector
26.3X17(mm ) module with 2X9 pin board to board connector
USB 2.0 (Full Speed)
4-layer single side
One printed Antenna,
Two W.FL RF connector for testing purpose,
One is for antenna path conductive testing, another is for ATT path
conductive testing.
4.2 Hardware Architecture
This Bluetooth module design is based on Broadcom BCM20702 chipset, which is a highly integrated
single chip solution for Bluetooth 4.0+EDR.
This Bluetooth device is operating at 2.4 GHz ISM band. For basic rate and EDR, it works with
hopping in 79 1MHz bandwidth channels, the channel center frequency is 2402+kMHz, k=0, 1,
2,……, 78. For Low energy, it uses 40RF channels, which have center frequencies at
2402+K*2MHz, where k=0, …, 39.
The Bluetooth module employs a 512Kbit serial flash and a 26MHz crystal, it use a 18pin board to
board connector to link host interface, power supply, and GPIOs to the Host.
5. Mechanical Drawing
COMPANY CONFIDENTIAL
6. Regulatory Information
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Labeling
Hon Hai Precision Bluetooth 4.0 module WIN-B3 labeled as below.
FCC ID: MCLWINB3
The proposed with FCC ID label format is to be placed on the module. If FCC ID is not
visible when the module is installed into the system, “Contains FCC ID: MCLWINB3”
shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
This device must not be co-located or operating in conjunction with any other antenna
or transmitter.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
undesired operation of this device.
The term “IC” before the equipment certification number only signifies that the Industry
Canada technical specifications were met.
Caution: Exposure to Radio Frequency Radiation.
To comply with IC RF exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
This device must not be co-located or operating in conjunction with any other antenna
or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Iver_Tao
Create Date                     : 2011:03:04 14:58:35Z
Modify Date                     : 2011:03:10 10:08:11+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : Iver_Tao
Title                           : Microsoft Word - WIN-B3_User manual_Rev1.0.doc
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2011:03:10 10:08:11+09:00
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:aa230fd9-c60e-4d8c-b69d-5719307a8a69
Instance ID                     : uuid:dcf158b7-19af-4999-83f3-92c3bf897190
Page Count                      : 7

EXIF Metadata provided by EXIF.tools