HON HAI PRECISION IND T77H134 WLAN & Bluetooth combo module User Manual UserMan MCLT77H134 revised

HON HAI Precision Ind. Co., Ltd. WLAN & Bluetooth combo module UserMan MCLT77H134 revised

UserMan_MCLT77H134-revised

.!2!.! MARVELL 88W8688 Mini-Module (IEEE 802.11b/g+BT 2.1 EDR) Marketing Requirements Specification T77H134.00 < REV.05> Prepared by Reviewed by Approved by Plum Feng Robin Xu Chang-fu Lin WLAN & BT combo module WLAN and Bluetooth combo module
.!3!.!CONTENTS 0. REVISION HISTORY..............................................................................................................................................3 1. INTRODUCTION ..........................................................................................................................................................4 1.1 SCOPE......................................................................................................................................................................4 1.2 FUNCTION.................................................................................................................................................................4 1.3 ENVIRONMENTAL......................................................................................................................................................4 2 PRODUCT SPECIFICATION ......................................................................................................................................5 2.1 HARDWARE SPECIFICATION.....................................................................................................................................5 3. PRODUCT REQUIREMENTS ....................................................................................................................................6 3.1 HARDWARE REQUIREMENTS....................................................................................................................................6 3.2 HARDWARE ARCHITECTURE....................................................................................................................................6 3.3 MECHANICAL OUTLINE DRAWING.............................................................................................................................7 3.4 LAND GRID ARRAY...................................................................................................................................................8 3.5 SOFTWARE REQUIREMENTS..................................................................................................................................10
.!4!.! 0. Revision History Date Change Note REV Note Nov. 11, 2008 Rev.01 0 Dec. 19, 2008 Rev.02 Update dimension of module Apr. 28, 2009 Rev.03 Change the pin-define Oct. 13.2009 Rev.04 Change the height of shielding Oct. 27.2009 Rev.05 Change the mechanical spec of shielding
.!5!.!1. Introduction Project Name: Mini-Module (802.11b/g + BT Module) based on Marvell IC 88W8688 with TFBGA package. This documentation describes the Engineering requirements specification of the WLAN (802.11b/g) +Bluetooth 2.1 EDR Mini-Module. It is a confidential document of FOXCONN. 1.1 Scope The Wireless MARVELL 88W8688BFL Mini-Module is designed to support 802.11g data rate of 54, 48, 36, 24, 18, 12, 9, 6Mbps, and as well as 802.11b data rate of 11, 5.5, 2, 1Mbps for WLAN operation. In addition, this module is Bluetooth 2.1+Enhanced Data Rate (EDR) compliant which provide 1, 2 and 3Mbps data rate. 1.2 Function Ɣ Compatible with IEEE 802.11b/g standard and Bluetoothv2.1+EDR standard Ɣ Ultra low-power dissipation Ɣ Support external power down mode Ɣ Support Marvell Wi-Fi/Bluetooth coexistence Ɣ Support the IEEE 802.11i security standard through implementation of the Advanced Encryption Standard (AES)/ Counter Mode CBC-Mac Protocol (CCMP) and WEP security mechanisms. Also supports Internet Protocol Security (IPSce) with DES/3DES/AES encryption and MD5/SHA-1 authentication. Ɣ Host interface supports for SDIO/ G-SPI, PCM/I2S Codec interface for multimedia application Ɣ Host interface supports for SDIO/ G-SPI, PCM/I2S Codec interface for multimedia application 1.3 Environmental Ambient Temperature (operation) = -10 to +75 Degrees Celsius. Product storage temperature = -40 to +85 Degrees Celsius.
.!6!.!2 Product Specification 2.1 Hardware Specification 2.1.1 WLAN Wireless LAN Standards IEEE 802.11g standard and IEEE 802.11b Operating Frequency 2.412~2.484GHz Channel Numbers 11 channels for United States 13 channels for Europe Countries 14 channels for Japan WLAN Data Rate 802.11g: 54Mbps with fall back of 48, 36, 24, 18, 12, 9, 6Mbps. 802.11b: 11Mbps with fall back rates of 5.5, 2, and 1Mbps Modulation Schemes 802.11g: 64QAM (54Mbps, 48Mbps), 16QAM (36Mbps, 24Mbps), QPSK (18Mbps, 12Mbps), BPSK (9Mbps, 6Mbps) 802.11b: CCK (11 Mbps, 5.5Mbps), DQPSK (2 Mbps), DBPSK (1 Mbps) Transmitter Output Power Typical 14dBm for 54, 48, 36, 24, 18, 12, 9, 6Mbps Typical 15dBm for 11, 5.5, 2, 1Mbps EVM 802.11b @11Mbps_14dBm (8%dB@peak) 802.11g @54Mbps_14dBm (-26dB@average) Receiver Sensitivity Typical –72dBm for 54Mbps @ 10% PER Typical –74dBm for 48Mbps @ 10% PER Typical –81dBm for 36Mbps @ 10% PER Typical –83dBm for 24Mbps @ 10% PER Typical –86dBm for 18Mbps @ 10% PER Typical –88dBm for 12Mbps @ 10% PER Typical –88dBm for 9Mbps @ 10% PER Typical –88dBm for 6Mbps @ 10% PER Typical –88dBm for 11Mbps @ 8% PER Typical –90dBm for 5.5Mbps @ 8% PER Typical –92dBm for 2Mbps @ 8% PER Typical –93dBm for 1Mbps @ 8% PER Media Access Protocol CSMA/CA with ACK 2.1.2 Bluetooth Radio Technology FHSS Operating Frequency 2402 ~ 2480MHz ISM band Channel Numbers 79 channels with 1MHz BW Transmitter Output Power -6~ +4dBm output power for class2 Receiver Sensitivity -80dBm @ GFSK 0.1% BER, 1Mbps Maximum Receiver Signal -20dBm and Taiwan. 11b : 22 dBm 11g : 25 dBm -
.!7!.!3. Product Requirements 3.1 Hardware Requirements Form factor LGA Host Interface SDIO PCB 6-layer FR4 Antenna port: One BT RF port and One Wi-Fi RF port 3.2 Hardware Architecture The module design is based on the MARVELL 88W8688BFL single chip which implements IEEE802.11b/g and Bluetooth 2.1+EDR. Figure 1 Functional Block Diagram MARVELL 88W8688BFL is a highly integrated, low-cost, low-power IEEE802.11 b/g MAC /Baseband / RF WLAN and Bluetooth Baseband/RF. The mini Module apply to WLAN /Bluetooth cellular handsets ,WLAN/Bluetooth headsets, portable audio/video devices and accessories , gaming platforms, and WLAN/Bluetooth enabled digital still cameras and printers. The single chip MARVELL 88W8688BFL interfaces directly with both the RF and digital signals. It transmits and receivers RF signals at 2.4GHz to and from the antenna and digital signals to and from the host interface. A power management (PMU) is placed in the off Board to provide power for all components in the module and also can save precious board space.
.!8!.!3.3 Mechanical outline Drawing The MARVELL 8688 Mini-Module 802.11b/g module shall be 6-layer PCB design. Dimension (W×L×H): 10.8mm ×15.8mm ×2.1mm (max.) (Bottom view) Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). , except tested built-in WLAN-BT collocation. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, except tested built-in WLAN-BT collocation. 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
.!9!.!3.4 Land Grid Array 3.4.1 LGA assignment and location˄˄˄˄top view˅˅˅˅ IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:MCLT77H134”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
.!:!.!3.4.2 Pin definition Pin name PIN# Function TCK C2 JTAG test clock input TDI F4 JTAG test data input TDO E3 JTAG test data output TMS2 D4 JTAG test mode select. Selects the system JTAG controller TRSTn C4 JTAG test reset(active low) TMS E4 JTAG test mode select. Selects the internal CPU JTAG controller BT-PCM-DOUT E5 PCM data output signal BT-PCM-MCLK E6 PCM clock signal (optional) Optional clock used for some codecs. Derived from PCM_CLK BT-PCM-CLK C8 PCM Clock Signal output if PCM master. Input if PCM slave BT-PCM-DIN D6 PCM data input signal BT-PCM-SYNC D5 PCM Sync Pulse Signal WLAN-LED D1 LED for WLAN indicator light GPIO17 B2 GPIO17 for BT LED(Wi-Fi IRQ) GPIO17 default high for SDIO interface, pull low for G-SPI interface WLAN F8 Wi-Fi RF Signal BT-OUT F1 BT RF Signal EXT-SLEEP-CLK D8 clock input for external 32.768KHz sleep clock VDD33 B7 3.3V voltage ,add at least 1uF cap bypass VDD30 C7 3.0V voltage ,add at least 1uF cap bypass VIO_X1 A2 1.8V or 3.3V voltage, add at least 1uF cap bypass VIO_X2 D3 1.8V or 3.3V voltage, add at least 1uF cap bypass SD-D3/SPI_CLK_REQ C1 SDIO data interface/G-SPI interface SD-D2/SPI_SINTn A3 SDIO data interface/G-SPI interface SD-D1/ SPI_SDO B3 SDIO data interface/G-SPI interface SD-D0/SPI_SCSn C3 SDIO data interface/G-SPI interface SD-CMD/ SPI_SDI A4 SDIO command/G-SPI interface SD-CLK/SPI_CLK B4 SDIO clock/G-SPI Clock CF-INPACK-N B6 PC card I/O mode input Acknowledge. Used by the card to indicate to the host that the card is selected and is responding to a read cycle. WLAN-MAC-WAKE B1 Host to indicate to the card is selected VDD18D C5 C6 1.8V voltage, add at least 1uF cap bypass VDD18_LDO B5 1.8V voltage, add at least 1uF cap bypass RESETn D7 Reset pin ,need external 100K res connected to 3.3 voltage to pull high PDn D2 Full power down (active low).Have 100K res to pull this pin high for normal operation in the module. No need external pull-up for this pin GPIO0 A7 NC for Reserve GND A1 A5 A6 A8 A9 B8 B9 C9 D9 E1 E2 E7 E8 E9 F2 F3 F5 F6 F7 F9 GND NCC ᤞ፿ : ᆖীڤᎁᢞٽ௑հ܅פ෷୴᙮ሽᖲΔॺᆖ๺ױΔֆ׹Ε೸ᇆࢨࠌشृ݁լ൓ᖐ۞᧢ޓ᙮෷Εף!!!Օפ෷ࢨ᧢ޓ଺๻ૠհ௽ࢤ֗פ౨Ζ ܅פ෷୴᙮ሽᖲհࠌشլ൓ᐙ᥼ଆ౰ڜ٤֗եឫٽऄຏॾΙᆖ࿇෼ڶեឫ෼ွழΔᚨمܛೖشΔࠀޏ࿳۟ྤեឫழֱ൓ᤉᥛࠌشΖছႈٽऄຏॾΔਐࠉሽॾऄ๵ࡳ܂ᄐհྤᒵሽຏॾΖ܅פ෷୴᙮ሽᖲႊݴ࠹ٽऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽंᘿ୴ࢤሽᖲ๻ໂհեឫΖ!ءᑓิ࣍࠷൓ᎁᢞ৵ലࠉ๵ࡳ࣍ᑓิء᧯ᑑقᐉٽ௑᧘Δࠀ૞ޣؓ؀Ղᑑقψءข঴փܶ୴᙮ᑓิΚIDᒳᇆω!
.!21!.!3.5 Software Requirements The software includes firmware, driver and configuration utility for Wireless WLAN 802.11 b/g + Bluetooth Module based on Marvell 88w8688BFL chip. 3.5.1 Software setup The software components required for operations will be packed into one installation program, thus user and customer can setup and upgrade software simply by running the setup program (ex. Setup.exe) without any obstacles. 3.5.2 Operating System Support All software components, including the installer will work on Microsoft Windows XP SP2. Driver for some common Linux systems is also supported, such as Fedora 8. Other Operate Systems (such as Microsoft Windows Vista RTM) will be supported if required by customer. 3.5.3 Software Functions For WLAN part, the WLAN configuration utility will include the Link Statistics Software, thus customers can evaluate various PHY performance parameters independent of system performance. This utility can also be used to change various WLAN parameters, such as SSID, Band, channel, Data rate, etc. The firmware and driver will fully compliance to the 802.11 published PHY and MAC specifications. It can support the following functions: z Scan for Wireless Networks z Connect to a Wireless Network z Change Profiles z Support security standards such as, WEP, WPA, WPA2, WPA-PSK, and WPA2-PSK. z Support ASPM z Support Marvell Bluetooth coexistence For Bluetooth part, a fully working Configuration Utility is supplied. It is: z Fully compliant with Bluetooth 2.1 +EDR(Enhanced Data Rate) specifications up to HCI (Host Controller Interface) layer z Support all standard operations: Inquiry scan, page scan, paring, authentication, link key, and encryption z Support many approved features of Bluetooth 2.1 release (Link Supervision Timeout, Encryption Pause/Resume, Extended Inquiry Response, Sniff Sub Rating) z Support all Bluetooth low power operation modes. (ie, hold, sniff, and park with configurable intervals). z Support sleep and standby modes for ultra low-power operation.

Navigation menu