Honsenn Technology BT-H802 HONSENN BLUETOOTH HEADPHONE User Manual 20140331

HONSENN TECHNOLOGY CO.,LTD HONSENN BLUETOOTH HEADPHONE 20140331

User Manual

WARNING: Do not place batteries in mouth or ingest. Keep out of reach of children and pets.Please dispose of any used batteries properly following any local regulations. Do not incinerate.PLEASE LISTEN RESPONSIBLYThe Occupational Safety Health Administration (OSHA) has issued headphone usage recommendations for maximum daily exposure and sound pressure levels(measured in decibels(dB). A decibel is a unit of measure of sound , and decibels increase exponentially as sound gets louder. For example, conversational speech is typically around 60dB, and a rock concert in a stadium is often about 110dB.OSHA GUIDELINES FOR NOISE EXPOSURE LIMITSFCC AND CANADA EMC COMPLIANCE INFORMATIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1 This device may not cause harmful interference and 2 this device must accept any interference received , including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiates radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Approved under the verification provision of FCC Part as a Class B Digital Device.Caution: Changes or modifications not expressly approved by the manufactured could void the user’s authority to operate this device.Caution: To comply with the limits the Class B digital device, pursuant to Part15 of the FCC Rules, this devices is to comply with Class B limits. All peripherals must be shielded and rounded. Operation with non-certified peripherals or non-shielded cables may result in interference to radio or reception.This Class B digital apparatus complies with Canadian ICES-003. 90dB 8hours95dB 4hours100dB 2hours105dB 1hour110dB 30minutes115dB 15minutes120dB Avoid as damage may occurSound Pressure level Recommended Maximum Exposure Per Day
WEEE NOTICENote: This mark applies only to countries within the European Union(EU) and Norway. This appliance is labeled in accordance with European Directive 2002/96/EC concerningwaste electrical and electronic equipment (WEEE).This label indicates that this productshould not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. WIRELESS TRANSMITTER COMPLIANCE INFORMATIONThe term”IC:”before the radio certification number only signifies that industry Canada technical specifications were met.This device complies with part 15 of the FCC Rules and the applicable industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions(1)this device may not cause harmful interference, and(2) this device must accept any interference ,including interference that may cause undesired operation of the device .SPECIFICATIONS BLUETOOTH V4.0+EDRRange: Up to 10m(33feet)Input rating:5V DC,0.5ACHARGINGCharge for 1hour before first use.When fully charged the battery will provide up to 10 hours of talking and/or music time.You can continue to use the headset while charging.Low battery (Battery Status Indicator):PAIRING Before using the headset for the first time it must be paired with a Bluetooth device (mobile phone, ect)1 Ensure the headset is off.2Hold the Power/Pairing button for 3 seconds. The headset will turn on then the status indicator will rapidly flash 3 Turn on Bluetooth on the device and set it to search for Bluetooth devices.4 Select “HONSENN802” from the device list.Once a device has been paired the headset will remember it. When the headset is turned on it will automatically scan for remembered device, beginning with the most recently paired. Up to 8 devices are memorized .TURNING ON/OFF VOLUME &MUSIC CONTROLS CALLS Make calls as normal from the phone, when the headset is connected the audio will automatically go to the headset DISCONNECT THE HEADSETTo disconnect the headset from the device, power the headset off or disconnect it in the Bluetooth menu of the deviceRECOONECT THE HEADSET To connect to the most recently used device, power the headset on. If Bluetooth is enabled on the device they will automatically reconnect. To connect to another remembered device, select “HONSENN” from the Bluetooth menu of the device. STATUS INDICATORExample: Blinks Blue Blinks Red Time Between BlinksB BR RB RRR RB B BB B BR B R BImage ONE Bluetooth Headset Direct Connect Audio Cable Micro USB Charging Cable123485671Audio jack 2 Status Indicator 3 Charging jack 4 Volume- 5 Track back 6 Volume+ 7 Track forward 8 Play/Pause, Anwer/End Call Hold 3 secondsStatus indicatorON OFF volume down volume upPrevious TrackNext trackPlay /PausePlay/Pause,Answer/End CallReject call-Hold 2 SecondsAnswer/End call-press one
USING WITH THE DIRECT CONNECT AUDIO CABLE The headset can be connected to an audio source using the direct connect audio cable. Note:When the audio cable is connected the Bluetooth function and controls are disabled..STATUS INDICATORExample: Blinks Blue Blinks Red Time Between BlinksB BR RB RGeneral and StandbyHSP(Phone Calls)PairingLow BatteryStandby (Bluetooth Connected)Standby（Bluetooth Not Connected）Outgoing call/Active CallBR RB B R RB B R B RB B B B B BR R RB B B B B BB B B B B BB B BlncomingFCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 　 Reorient or relocate the receiving antenna. 　 Increase the separation between the equipment and receiver. 　 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 　 Consult the dealer or an experienced radio/TV technician for help. RF warning statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu