HP VPro Setup And Configuration For The Dc7700 Business PC With Intel Technology V Pro C00767138
User Manual: HP vPro Setup and Configuration for the dc7700 Business PC with Intel vPro Technology
Open the PDF directly: View PDF
Page Count: 30
- vPro Setup and Configuration for the dc7700 Business PC with Intel vPro Technology
- Introduction
- AMT Setup and Configuration
- AMT System Phases
- SMB Mode - AMT Setup and Configuration with MEBx
- SMB Mode - AMT Setup and Configuration Steps
- 1. Press Ctrl-P during POST to enter Manageability Engine BIOS Extension (MEBx) Setup. You can dis play this option only during POST if set in F10-Setup.
- 2. Type the default password, which is admin. Passwords are case-sensitive.
- 3. Change the MEBx password. The new password must meet the Strong Password criteria defined in the Password Guidelines Section. Type the password twice for verification.
- 4. Select the Intel ME Platform Configuration. A window displays indicating that the system resets after configuration.
- 5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on.
- 6. Select Intel ME State Control, and then select Enabled.
- 7. Select Intel ME Firmware Local Update Qualifier, and then select Always Open.
- 8. Skip LAN Controller.
- 9. Select Intel ME Features Control.
- 10. Select Intel ME Power Control.
- 11. Return to previous menu to exit the MEBx Setup and save AMT configuration. The system will display an Intel ME Configuration Complete message and reboot.
- 12. Press Ctrl-P during POST to enter MEBx Setup again.
- 13. Type the MEBx password.
- 14. Select Intel AMT Configuration.
- 15. Select Host Name, and then type a host name.
- 16. Select TCP/IP.
- 17. Skip Provisioning Server.
- 18. Select Provision Model.
- 19. Skip Un-Provision. This option returns the system to factory defaults. See “Return to Default” on page 23 for more information about unprovisioning.
- 20. Skip VLAN.
- 21. Select SOL/IDE-R.
- 22. Select Remote Firmware Update, and then select Enabled.
- 23. Select Idle Timeout.
- 24. Select Return to previous menu.
- 25. Select Exit, and then select Y to exit the MEBx Setup and save settings.
- Intel AMT WebGUI
- Connecting with the Intel AMT WebGUI - SMB Example
- 1. Power on an AMT system that has completed AMT Setup and Configuration.
- 2. Execute a Web browser from a separate system - a Management computer on the same subnet as the AMT computer.
- 3. Connect to the IP address specified in the MEBx and port of the AMT system.
- 4. Type the user name and password. The default username is admin and the password is what you set during AMT Setup in the MEBx.
- 5. Review system information and/or make any necessary changes.
- 6. Select Exit.
- Connecting with the Intel AMT WebGUI - SMB Example
- Enterprise Mode Setup and Configuration
- Enterprise Mode - AMT Setup and Configuration Steps
- 1. Access the MEBx by pressing Ctrl-P during POST.
- 2. Type the default password, which is admin.
- 3. Change the MEBx password, following strong password guidelines.
- 4. Select Intel ME Platform Configuration.
- 5. In Intel ME State Control, select Enabled.
- 6. In Intel ME Firmware Local Update Qualifier, select Always Open.
- 7. Skip LAN Controller.
- 8. Select Intel ME Features Control.
- 9. Select Intel ME Power Control.
- 10. Select Exit and save. The system displays the Intel ME Configuration Complete message, and then reboots.
- 11. Press Ctrl-P during POST to enter MEBx Setup again.
- 12. Type the MEBx password.
- 13. Select Intel AMT Configuration. The Intel AMT Configuration screen includes numerous options, which are available by scrolling down the menu.
- 14. Select Host Name, and then type a host name
- 15. Select TCP/IP.
- 16. Select Provisioning Server.
- 17. Select Provision Model.
- 18. Select Set PID and PPS.
- 19. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default sec tion for more information about unprovisioning.
- 20. Skip VLAN.
- 21. Select SOL/IDE-R, and then select Y.
- 22. Select Remote Firmware Update, and then select Enabled.
- 23. Skip Set PRTC.
- 24. Select Idle Timeout.
- 25. Select Return to previous menu.
- 26. Select Exit, and then select Y to exit the MEBx Setup and save settings. The system displays an Intel ME Configuration Complete message and reboots.
- 27. Turn off the system and remove power. The system is now in In-Setup Mode and is ready for deploy ment.
- 28. Plug the system into a power source and connect the network. Use the integrated Intel 82566DM NIC. Intel AMT does not work with any other NIC solution.
- Setup and Configuration Server Preparation
- Enterprise Mode - AMT Setup and Configuration Steps
- Provisioning Methods
- Return to Default
- Full Return to Factory Defaults
- USB Drive Key Set Up and Configuration
- 1. An IT technician inserts a USB drive key into a system with a management console.
- 2. The technician request local setup and configuration records from an S&CS through the console.
- 3. The S&CS:
- 4. The management console writes the password, PID, and PPS sets to a Setup.bin file in the USB drive key.
- 5. The technician takes the USB drive key to the staging area where new AMT platforms are located. The technician:
- 6. The system BIOS detects the USB drive key.
- 7. The system BIOS displays a message that automatic setup and configuration will occur.
- 8. MEBx processes the record.
- 9. MEBx writes a completion message to display.
- 10. The IT technician powers down the system. The system is now in In-Setup phase and is ready to be dis tributed to users in an Enterprise mode environment.
- 11. Repeat Step 5 if necessary (more than one system).
- USB Drive Key Requirements
- Appendix A: Frequently Asked Questions
- Appendix B: Power / Sleep / Global States Explained
- Appendix C: Wake-On-ME Explained
- AMT Setup and Configuration