Contents
- 1. User manual (statement)
- 2. User manual
User manual (statement)
Safety and
regulatory guide
2 Safety and regulatory guide
Please read before proceeding
THE BATTERY IS NOT FULLY CHARGED WHEN YOU TAKE THE
DEVICE OUT OF THE BOX.
Privacy restrictions
Some countries require full disclosure of recorded telephone
conversations.
Important health information and safety
precautions
When using this product, the safety precautions below must be
taken to avoid possible legal liabilities and damages.
Retain and follow all product safety and operating instructions.
Observe all warnings in the operating instructions on the product.
To reduce the risk of bodily injury, electric shock, fire, and damage
to the equipment, observe the following precautions.
Electrical safety
This product is intended for use when supplied with power from
the designated battery or power supply unit. Other usage may be
dangerous and will invalidate any approval given to this product.
Safety precautions for proper grounding installation
CAUTION
: Connecting to improperly grounded equipment can
result in an electric shock to your device.
This product is equipped with a USB Cable for connecting with
desktop or notebook computer. Be sure your computer is properly
grounded (earthed) before connecting this product to the
computer. The power supply cord of a desktop or notebook
computer has an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate
outlet which is properly installed and grounded in accordance with
all local codes and ordinances.
Safety precautions for power supply unit
Use the correct external power source
A product should be operated only from the type of power
source indicated on the electrical ratings label. If you are not
sure of the type of power source required, consult your
authorized service provider or local power company. For a
product that operates from battery power or other sources,
refer to the operating instructions that are included with the
product.
Safety and regulatory guide 3
This product should be operated only with the following
designated power supply unit(s).
AC adapter:
HTC, TC U250
Handle battery packs carefully
This product contains a Lithium-ion polymer or Lithium-ion battery.
There is a risk of fire and burns if the battery pack is handled
improperly.
WARNING
: Danger of explosion if battery is
incorrectly replaced. To reduce risk of fire or burns,
do not disassemble, crush, puncture, short external
contacts, expose to temperature above 60° C
(140° F), or dispose of in fire or water. Replace only
with specified batteries. Recycle or dispose of used
batteries according to the local regulations or
reference guide supplied with your product.
NOTE
: This product should be operated only with the following
designated Battery Pack(s).
HTC, Model BM65100
Take extra precautions
Keep the battery or device dry and away from water or any
liquid as it may cause a short circuit.
Keep metal objects away so they don’t come in contact with
the battery or its connectors as it may lead to short circuit
during operation.
The phone should only be connected to products that bear
the USB-IF logo or have completed the USB-IF compliance
program.
Do not use a battery that appears damaged, deformed, or
discolored, or the one that has any rust on its casing,
overheats, or emits a foul odor.
Always keep the battery out of the reach of babies and small
children, to avoid swallowing of the battery. Consult the
doctor immediately if the battery is swallowed.
If the battery leaks:
Do not allow the leaking fluid to come in contact with skin or
clothing. If already in contact, flush the affected area
4 Safety and regulatory guide
immediately with clean water and seek medical advice.
Do not allow the leaking fluid to come in contact with eyes. If
already in contact, DO NOT rub; rinse with clean water
immediately and seek medical advice.
Take extra precautions to keep a leaking battery away from
fire as there is a danger of ignition or explosion.
Safety precautions for direct sunlight
Keep this product away from excessive moisture and extreme
temperatures. Do not leave the product inside a vehicle or in
places where the temperature may exceed 60
°
C (140
°
F), such as
on a car dashboard, window sill, or behind glass that is exposed to
direct sunlight or strong ultraviolet light for extended periods of
time. This may damage the product, overheat the battery, or pose
a risk to the vehicle.
Prevention of hearing loss
CAUTION
: Permanent hearing loss may occur if earphones or
headphones are used at high volume for prolonged periods of time.
Safety in aircraft
Due to the possible interference caused by this product to an
aircraft’s navigation system and its communications network,
using this device’s phone function on board an airplane is against
the law in most countries. If you want to use this device when on
board an aircraft, remember to turn off your phone by switching to
Airplane Mode.
Environment restrictions
Do not use this product in gas stations, fuel depots, chemical
plants or where blasting operations are in progress, or in
potentially explosive atmospheres such as fuelling areas, fuel
storehouses, below deck on boats, chemical plants, fuel or
chemical transfer or storage facilities, and areas where the air
contains chemicals or particles, such as grain, dust, or metal
powders. Please be aware that sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death.
When in any area with a potentially explosive atmosphere or
where flammable materials exist, the product should be turned off
and the user should obey all signs and instructions. Users are
advised not to use the equipment at refueling points such as
service or gas stations, and are reminded of the need to observe
restrictions on the use of radio equipment in fuel depots, chemical
Safety and regulatory guide 5
plants, or where blasting operations are in progress.
Road safety
Full attention must be given to driving at all times in order to
reduce the risk of an accident. Using a phone while driving (even
with a hands free kit) causes distraction and can lead to an
accident. You must comply with local laws and regulations
restricting the use of wireless devices while driving.
Safety precautions for RF exposure
Avoid using your phone near metal structures (for example, the
steel frame of a building).
Avoid using your phone near strong electromagnetic sources,
such as microwave ovens, sound speakers, TV and radio.
Use only original manufacturer-approved accessories, or
accessories that do not contain any metal.
Use of non-original manufacturer-approved accessories may
violate your local RF exposure guidelines and should be avoided.
Hearing aids
Some digital wireless phones may interfere with some hearing aids.
In the event of such interference, you may want to consult your
service provider, or call the customer service line to discuss
alternatives.
Electrical safety
Accessories
Use only approved accessories.
Do not connect with incompatible products or accessories.
Connection to a car
Seek professional advice when connecting a phone interface to
the vehicle electrical system.
Faulty and damaged products
Do not attempt to disassemble the phone or its accessory.
Only qualified personnel must service or repair the phone or
its accessory.
General precautions
You alone are responsible for how you use your phone and any
consequences of its use. You must always switch off your phone
wherever the use of a phone is prohibited. Use of your phone is
subject to safety measures designed to protect users and their
environment.
6 Safety and regulatory guide
Avoid applying excessive pressure to the device
Do not apply excessive pressure on the screen and the device to
prevent damaging them. It is also recommended that you store
the device in a protective case and only use your finger when
interacting with the touch screen. Cracked display screens due
to improper handling are not covered by the warranty.
Protect your phone
Always treat your phone and its accessories with care and
keep them in a clean and dust-free place.
Do not expose your phone or its accessories to open flames or
lit tobacco products.
Do not drop, throw or try to bend your phone or its
accessories.
Do not use harsh chemicals, cleaning solvents, or aerosols to
clean the device or its accessories.
Do not paint your phone or its accessories.
Do not attempt to disassemble your phone or its accessories,
only authorised personnel must do so.
Store your phone or its accessories at temperatures between
0°C to 40°C.
Please check local regulations for disposal of electronic
products.
Damage requiring service
Unplug the product from the electrical outlet and refer servicing
to an authorized service technician or provider under the
following conditions:
The product has been exposed to rain or liquid, dropped,
subject to impact or damaged.
There are noticeable signs of overheating.
The product does not operate normally when you follow the
operating instructions.
Avoid hot areas
The product should be placed away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
Avoid wet areas
Never use the product in rain, or near washbasins or other wet or
high humidity locations. If your product gets wet, do not try to
dry the product with the use of an oven or dryer, as this may
damage your product.
Avoid using your device after a dramatic change in temperature
Safety and regulatory guide 7
When you move your device between environments with very
different temperature and/or humidity ranges, condensation
may form on or within the device. To avoid damaging the device,
allow sufficient time for the moisture to evaporate before using
the device.
NOTICE
: When taking the device from low-temperature
conditions into a warmer environment or from high-temperature
conditions into a cooler environment, allow the device to
acclimate to room temperature before turning on power.
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or other
openings in the product. Slots and openings are provided for
ventilation. These openings must not be blocked or covered.
Adjust the volume
Turn down the volume before using headphones or other audio
devices.
Cleaning
Unplug the product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning, but NEVER use water to clean the LCD screen.
Small children
Do not leave your phone and its accessories within the reach of
small children or allow them to play with it. They could hurt
themselves or others, or could accidentally damage the phone.
Your phone contains small parts with sharp edges that may
cause an injury or which could become detached and create a
choking hazard. Consult the doctor immediately if the
accessories or battery are swallowed.
Repetitive motion injuries
To minimise the risk of repetitive strain injuries, when texting or
playing games with your phone:
Do not grip the phone too tightly
Press the buttons lightly
Electrostatic discharge (ESD)
Do not touch the SIM card’s metal connectors.
Emergency calls
This phone, like any wireless phone, operates using radio signals,
which cannot guarantee connection in all conditions. Therefore,
you must never rely solely on any wireless phone for emergency
communications.
8 Safety and regulatory guide
Regulatory agency identifications
For regulatory identification purposes, your product is assigned a
model number of
0P4E230
.
FCC ID:
NM80P4E230
.
To ensure continued reliable and safe operation of your device use
only the HTC qualified battery with your
0P4E230
: Battery Pack,
model number
BM65100
.
NOTE:
This product is intended for use with a certified Class 2
Limited Power Source, rated 5 Volts DC, maximum 1 Amp power
supply unit.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
This Category II radio communication device complies with
Industry Canada Standard RSS-310.
IMPORTANT NOTE:
The Country Code selection for 2.4 GHz WLAN is disabled on this
device. Operation in the 2.4 GHz band is restricted to Channels 1 –
11.
Operation in the 5 GHz Band
Operation in the 5150-5250 MHz band is restricted by Industry
Canada and the FCC to indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems.
High-power radars are allocated as primary users (i.e. priority
users) of the bands 5250-5350 MHz and 5650-5850 MHz and
that these radars could cause interference and/or damage to
LE-LAN devices.
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
Safety and regulatory guide 9
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio or television
technician for help.
FCC Caution
: Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
RF Radiation Exposure Statement
This equipment has been tested and found to comply with FCC
and Industry Canada radiation exposure limits for use in an
uncontrolled environment, in accordance with the procedures
specified by FCC rules, IEEE 1528, and IEC 62209-2.
This transmitter has been tested and found to comply with
co-location compliance requirements for built-in Bluetooth and
WLAN.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Use only the supplied or an approved antenna. Unauthorized
antennas, modifications, or attachments could impair call quality,
damage the phone, or result in violation of regulations. Do not use
the phone with a damaged antenna. If a damaged antenna comes
into contact with the skin, a burn may result. Please contact your
local dealer for replacement antenna.
FCC Hearing-Aid Compatibility (HAC) Regulations for
Wireless Devices
The FCC has adopted rules to ensure reasonable access to
10 Safety and regulatory guide
telecommunications services for persons with hearing disabilities.
As part of this effort, the industry uses a rating system for wireless
phones to help hearing device users find phones that may be
compatible with their hearing devices (hearing aids and cochlear
implants). This hearing-aid compatibility (HAC) rating system is
described in the American National Standards Institute (ANSI)
C63.19 standard and includes the following ratings:
M-Ratings:
For phones that use acoustic coupling with hearing
devices that are not operating in telecoil mode.
Phones rated M3
or M4 meet FCC HAC requirements and are likely to generate less
radio frequency interference with hearing devices than phones
with lower ratings. M4 is the better/higher of the two ratings. Your
0P4E230
is rated
M3
.
T-Ratings:
For phones that use inductive coupling with hearing
devices operating in telecoil mode.
Phones rated T3 or T4 meet
FCC HAC requirements and are likely to be more usable with a
hearing aid’s telecoil than phones that are not rated. T4 is the
better/higher of the two ratings. Your
0P4E230
is rated
T4
.
This phone has been tested and rated for use with hearing aids for
some of the wireless technologies that it uses. However, there may
be some newer wireless technologies used in this phone that have
not been tested yet for use with hearing aids. It is important to try
the different features of this phone thoroughly and in different
locations, using your hearing aid or cochlear implant, to determine
if you hear any interfering noise. Consult your service provider or
the manufacturer of this phone for information on hearing aid
compatibility. If you have questions about return or exchange
policies, consult your service provider or phone retailer.
The ratings are not guarantees. Trying out the phone with your
hearing device is the best way to evaluate it for your personal
needs. Results will vary depending on a user’s hearing device and
hearing loss. For example, if some wireless phones are used near
some hearing devices, users may detect a buzzing, humming, or
whining noise. Some hearing devices are more immune than others
to this interference noise, and phones also vary in the amount of
interference they generate. If your hearing device happens to be
vulnerable to interference, you may not be able to use a rated
phone successfully.
Please power off the Bluetooth function while using hearing aid
devices with your
0P4E230
.
Safety and regulatory guide 11
For information about hearing aids and digital wireless
phones
FCC Hearing Aid Compatibility and Volume Control:
http://www.fcc.gov/cgb/dro/hearing.html
Hearing Aid Compatibility for Wireless Telephones
http://www.fcc.gov/guides/hearing-aid-compatibility-wireless
-telephones
Exposure to Radio Frequency Energy
Your wireless device has an internal antenna that emits radio
frequency (RF) energy. Human exposure to RF energy has been
and continues to be the subject of scientific research. According to
the U.S. Food and Drug Administration (FDA), “the weight of
scientific evidence has not linked cell phones with any health
problems.” You can access this FDA publication and other
information on human exposure to RF energy at:
U.S. Food and Drug Administration:
http://www.fda.gov/Radiation-EmittingProducts/RadiationEmittingPr
oductsandProcedures/HomeBusinessandEntertainment/CellPhones/u
cm116282.htm
Federal Communications Commission:
http://www.fcc.gov/encyclopedia/radio-frequency-safety
NIH National Institute of Environmental Health Sciences:
http://www.niehs.nih.gov/health/topics/agents/cellphones/
Health Canada:
http://www.hc-sc.gc.ca/hl-vs/iyh-vsv/prod/cell-eng.php
World Health Organization:
http://www.who.int/mediacentre/factsheets/fs193/en/
IEEE Committee on Man and Radiation:
http://ewh.ieee.org/soc/embs/comar/
International Commission on Non-Ionizing Radiation Protection:
http://www.icnirp.de/
Specific Absorption Rate (SAR) Testing
Your device has been designed to comply with applicable limits for
RF exposure. These limits use a unit of measurement called
Specific Absorption Rate, or SAR, which refers to the rate at which
the body absorbs RF energy. The Federal Communications
Commission (FCC) has established a SAR limit for mobile phones
of 1.6 W/kg, which applies in the United States and other countries
that follow the FCC’s SAR limit. This limit is based upon standards
12 Safety and regulatory guide
developed by expert non-government organizations, such as the
Institute of Electrical and Electronics Engineers (IEEE) and the
National Council on Radiation Protection and Measurements
(NCRP), and input from other federal agencies such as the FDA
and EPA. In countries that follow the Council of the European
Union, the SAR limit is 2.0 W/kg.
SAR testing is conducted with the device placed in common
operating positions (e.g., held against the head, worn on the body)
and transmitting at its highest certified power level in each
frequency band of operation. Because the device is transmitting at
its highest certified power level, SAR tests capture a worst-case
operating scenario and therefore often do not reflect the amount
of RF exposure during normal, everyday use. More information on
SAR testing is available on the FCC’s website at
http://www.fcc.gov/guides/wireless-devices-and-health-concerns
.
HTC Corp. submitted SAR test results demonstrating compliance
with the FCC’s SAR limit for wireless devices as part of the FCC’s
equipment certification process for this device. These results can
be accessed via the FCC’s equipment authorization database
(found at http://transition.fcc.gov/oet/ea/fccid/) by searching for
the device’s FCC ID:
NM80P4E230.
This device’s maximum SAR
values as reported to the FCC are:
Head: 0.77 W/kg@1g
Body-worn Accessory: 1.19 W/kg@1g
Body-worn Operation
This device was tested for compliance with applicable SAR limits
during typical body-worn operations. To ensure that RF exposure
levels remain at or below the tested levels, use a belt-clip, holster,
or similar accessory that maintains a minimum separation distance
of 1.0 cm between your body and the device, with either the front
or back of the device facing towards your body. Such accessories
should not contain any metallic components. Body-worn
accessories that do not meet these specifications may not ensure
compliance with applicable SAR limits and their use should be
avoided.
Reducing RF Exposure
Organizations such as the FCC have identified the following
measures to reduce your exposure to RF energy:
Use speaker mode or a hands-free accessory to minimize time
spent with the wireless device held against your head;
Safety and regulatory guide 13
Increase the distance between the wireless device and your
head and body; and
Send texts instead of making or receiving voice calls.
For more information, see the FCC’s web page on Wireless
Devices and Health Concerns at
http://www.fcc.gov/guides/wireless-devices-and-health-concerns.
WEEE notice
The Directive on Waste Electrical and Electronic Equipment
(WEEE), which entered into force as European law on 13th
February 2003, resulted in a major change in the treatment of
electrical equipment at end-of-life.
The purpose of this Directive is, as a first priority, the prevention of
WEEE, and in addition, to promote the reuse, recycling and other
forms of recovery of such wastes so as to reduce disposal.
The WEEE logo (shown at the left) on the product or
on its box indicates that this product must not be
disposed of or dumped with your other household
waste. You are liable to dispose of all your electronic
or electrical waste equipment by relocating over to
the specified collection point for recycling of such
hazardous waste. Isolated collection and proper
recovery of your electronic and electrical waste
equipment at the time of disposal will allow us to help
conserving natural resources. Moreover, proper
recycling of the electronic and electrical waste
equipment will ensure safety of human health and
environment. For more information about electronic
and electrical waste equipment disposal, recovery,
and collection points, please contact your local city
center, household waste disposal service, shop from
where you purchased the equipment, or
manufacturer of the equipment.
RoHS compliance
This product is in compliance with Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011, on the
restriction of the use of certain hazardous substances in electrical
and electronic equipment (RoHS) and its amendments.
14 Safety and regulatory guide
Proprietary Notice
© 2013 HTC Corporation. All rights reserved. HTC, the HTC logo,
HTC Desire, and the HTC Desire logo are trademarks of HTC
Corporation.
91H0XXXX-XXM Rev.A
htc.com