HTC HIMALAYAS Wireless PDA Phone User Manual Andes QSG indd

Download:
Mirror Download [FCC.gov]
Document ID	400068
Application ID	tO12oHBgIDi/ODsflIW/sw==
Document Description	revised manual page 14 to 28
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	235.65kB (2945567 bits)
Date Submitted	2004-02-27 00:00:00
Date Available	2003-10-07 00:00:00
Creation Date	2004-02-27 16:53:00
Producing Software	Adobe PDF Library 5.0
Document Lastmod	2004-02-27 16:53:22
Document Title	Andes_QSG.indd
Document Creator	Adobe InDesign 2.0.2

With Block Recognizer you can input character strokes using the
stylus that are similar to those used on other devices.
Tap the arrow next to the Input Panel button and then Block
Recognizer.
Write a letter in the box.
When you write a letter, it is converted to typed text that appears on
the screen. For specific instructions on using Block Recognizer, with
Block Recognizer open, taps the question mark next to the writing
area.
To switch to Transcriber
With Transcriber you can write anywhere on the screen using the
stylus just as you would on paper. Unlike Letter Recognizer and Block
Recognizer, you can write a sentence or more of information. Then,
pause and let Transcriber change the written characters to typed
characters.
Tap the arrow next to the Input Panel button and then Transcriber.
Write anywhere on the screen.
For specific instructions on using Transcriber, with Transcriber open,
tap the question mark in the lower right hand corner of the screen.
Using for the First Tiem
To use Block Recognizer
Using for the First Time
Write your first notes (Cont'd)
To punctuate in Transcriber
Tap the keyboard on the toolbar.
Tap OK to hide the keyboard.
To see how to write a letter in Transcriber
Tap “a” on the toolbar.
In the screen that appears, select the letter you want to learn about,
and then tap on one of the examples given above.
For specific instructions on using Transcriber, with Transcriber open,
tap the question mark in the lower right hand corner of the screen.
Click on a letter
for a demonstration
To make a call from Dialer
Press Send to enter the Home screen.
Dial the number you want to call using the keypad.
If the number or name is already in your contacts list, enter the name
or number of the person you want to call.
When it appears in the list, scroll to it and press the Talk key.
To make a call from Contacts
You can make a call from Contacts in the following ways :
Option 1
Press the Microsoft Contacts Button, find the contact and then tap
the left button twice -- once to send to the dialer screen and once
to call.
The pop up menu and the left button will by default display Call
Work Tel. However, you can customize so that the mobile
number or email is displayed instead:
Option 2
Select a contact in the contacts list and then press left or right on
the navigation pad -- the number on the screen will change.
Option 3
In the contacts list, tap the w in the right column next to the
contact you want to customize. A pop-up menu will display
the phone numbers and email addresses for this contact
with a dot next to the priority number.
In the pop-up menu select a priority -- If you selected mobile
number, m should now be in the right column next to the
contact.
Using for the First Tiem
Make Your First Call
Using for the First Time
Write your first text message or email
Press Send, tap Tools, and then Send SMS.
The screen below will appear.
Tap New.
In the TO field, enter either e-mail address or SMS number of one
or more recipients, separating them with a semicolon, or select a
name from the contact list by tapping the Address Book button. All
e-mail addresses entered in the e-mail fields in Contacts appear in
the Address Book.
Compose your message. Tap Send.
To enter preset or frequently used message, tap My Text and select
a message.
Setting up your phone for using the Internet, email and WAP is one of the most
important things you will have to do. However, once done, you will be able to
access a world of information anywhere, all at the touch of a few keys.
Obtain the following information from your ISP: ISP server phone
number, user name, and password.
Tap
In My ISP, tap Add a new modem connection.
Create a modem connection.
→ Setting → Connections tab → Connections
Wireless connections can be made via a mobile phone network
or GPRS. If you are using a mobile phone network to connect,
in the Select a modem list, tap Cellular Line. If you are using
GPRS, tap Cellular Line (GPRS).
To start the connection, begin using the desired program. For
example, switch to Pocket Internet Explorer and browse to a Web
page. Your device will automatically connect.
n To set up a network card or wireless network connection
to your ISP, add a new connection under My Work
Network.
n To change modem connection settings, in either My ISP
or My Work Network, tap Manage existing connections.
Select the desired modem connection, tap Settings,
and follow the instructions on the screen.
To view additional information for any screen in the ward or
while changing settings, tap
You can use GPRS to connect to your mobile ISP :
Using for the First Tiem
Set up to access email, WAP and the Internet
Using for the First Time
Setting up your e-mail account
Prepare your email account details.
In Inbox on your device, tap Accounts, and then New Account.
Follow the directions in the New Account wizard Press Menu, scroll
to Options, press Action and then enter E-mail setup.
To fill you e-mail address in the field, and then tap Next.
Enter “Your name”, your “User name” and “Password” then tap
Next.
From the drop down menu select the “Service type” that your email
provider supports (POP3 or IMAP4).
Enter a “Name” for your email account then tap Next
Enter the your email provider’s server name information for Incoming
mail and Outgoing mail, then tap Finish.For an explanation of a
screen, tap
and then Help. When finished, to connect to your
e-mail server, tap Accounts and then Connect.
When you have finished, you will see the Set-up Complete screen.
Press Finish to save the account. You can repeat the process for as
many accounts as you wish to setup.
Tap
and then Internet Explorer.
Using for the First Time
To browse the Internet
In the address bar that appears at the top of the screen,
enter the Web address you want to visit.
Tap
Tap
the Favorites button, and then tap the favorite you
want to view.
Tap
to go back to the Homepage you set.
Tap
to refresh the web page on the screen.
Tap the arrow
addresses.
Go to the web address you entered.
to choose from previously entered
To view mobile favorites and channels
Tap the Favorites button to display your list of favorites.
Tap the page you want to view.
You will see the page that was downloaded the last time you
synchronized with your PC. If the page is not on your device,
the favorite will be dimmed. You will need to synchronize
with your PC again to download the page to your device, or
connect to the Internet to view the page.
To add a favorite link while using the device, go to the page
you want to add, tap and hold on the page, and tap Add to
Favorites.
Using for the First Tiem
Accessing information using Pocket Internet Explorer
Bluetooth
Bluetooth
Bluetooth is a short-range wireless communications technology. Devices with
Bluetooth capabilities can exchange information over a distance of about 30 feet
without requiring a physical connection.
Unlike infrared, you don't need to line up the devices to beam information with Bluetooth. The devices only need to be within a range of about 30 feet. You can even
beam information to a device in a different room, as long as it's within range.
The software included with your Pocket PC Phone allows you to use Bluetooth
in following ways :
Beam information, such as files, appointments, tasks, and contact
cards, between devices that have Bluetooth capabilities. For example, if you and a co-worker each have a device with Bluetooth,
you can beam items between your devices, such as files, contact
cards, appointments, tasks, and so forth.
Create a dial-up modem connection between your device and
a Bluetooth phone. You can then use the Bluetooth phone as a
modem.
Bluetooth modes
Bluetooth operates in three different modes:
a. On
The Bluetooth radio is turned on and you can use Bluetooth features.
b. Off
The Bluetooth radio is turned off. In this mode, you can neither send nor receive
information by using Bluetooth. You might want to turn the radio off at times in
order to conserve battery power, or in situations where radio use is prohibited,
for example on airplanes and in hospitals.
c. Discoverable
The Bluetooth radio is turned on, and all of the other Bluetooth devices within
range (about 30 feet) can detect your device and attempt to beam information to
Other Bluetooth devices can now detect your device and attempt to beam information to it, establish a bond, or use a Bluetooth service. Note that to receive
beamed information, you must accept it on your device.
If you no longer want your device to be discoverable, tap Off to turn off the radio
or On to leave the radio on, but not allow detection by other devices.
Bonds
A bond is a relationship that you create between your Pocket PC and another
Bluetooth device in order to exchange information in a secure manner. Creating
a bond involves entering the same personal identification number (PIN) on the
two devices you want to bond. You need only create a bond once between two
devices. Once a bond is created, the devices recognize the bond and are able
to exchange information without your entering a PIN again.
Beaming Information with Bluetooth
Tap and hold an item to beam, such as an appointment in Calendar, a
task in Tasks, a contact card in Contacts, or a file in File Manager.
Tap Beam [type of item].
Tap the device to which you want to send the beam.
The item is beamed to the device you selected.
Receiving a Bluetooth Beam
Make sure that your device is configured to receive incoming beams
and that Bluetooth is in discoverable mode.
Make sure that your device is within 30 feet of the device beaming
the information.
3 When prompted to receive an incoming beam, tap Yes.
The information is now stored on your device.
Bluetooth
it, establish a bond, or use a Bluetooth service. In this mode, other devices can
detect your device whether or not a bond has been created; however, in order to
receive a beam from another device, you must accept it on your device. To make
your device discoverable:
Regulatory Notice
Regulatory Agency
Identification Numbers
For regulatory identification purposes your product is
assigned a model number PH10xx.
The following accessories have been evaluated for use with
your device. Their assigned model numbers listed below can
identify these approved accessories. To ensure continued
reliable and safe operation of your Pocket PC Phone, use
only the accessories listed below with your PH10xx.
Accessories
ETSI EN 301 511
Global system for mobile communications (GSM);
Harmonized EN for mobile stations in the GSM 900
and GSM 1800 bands covering essential requirements
of article 3.2 of the R&TTE directive (1995/5/EC )
ETSI EN 301 489-1
Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services; Part 1:
Common technical requirements
ETSI EN 301 489-7
Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services;
Part 7: Specific conditions for mobile and protable
radio and ancillary equipment of digital cellular radio
teleommunications systems (GSM and DCS)
ETSI EN 301 489-17
Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility
(EMC) standard for radio equipment and services;
Part 17: Specific conditions for 2.4 GHz wideband
transmission systems and 5 GHz high performance
RLAN equipment.
ETSI EN 300 328
Electromagnetic compatibility and Radio spectrum
Matters (ERM); Wideband Transmission systems;
data transmission equipment operating in the 2.4 GHz
ISM band and using spread spectrum modulation
techniques.
GSM11.10
ANSI/IEEE C.95.1-1992
Specific absorption rate in mobile phone emission
condition for body health
EN50360, EN50371 for SAR
SAR : 0.271mW/10g
Model Number
Cradle
PH15x
CF Back Pack
PH16x
Battery Pack
PH17x
n The above X may be any alphanumeric
character or blank denoting external
cosmetic changes.
n This product is intended for use with certified
Class 2 Limited Power Source, rated 5 VDC,
minimum 2A power supply unit.
European Union Notice
Products with CE marking comply with the R&TTE Directive
(99/5/EC), the EMC Directive (89/336/EEC) and the Low
Voltage Directive (73/23/EEC) issued by the Commission
of the European Community.
Compliance with these directives implies conformity to the
followng European Norms (in brackets are the equivalent
international standards):
EN 60950 (IEC 60950)
Safety of InformationTechnology Equipment.
n
FCC part 15 and part 24
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions : (!) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
FCC ID : NM8HIMALAYAS
Statement according to FCC part 15.21
Modifications not expressly approved by HTC could void
the user's authority to operate the equipment.
Statement according to FCC part 15.105
NOTE : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician
for help..
RF exposures
Tests for SAR are conducted using standard operating
positions specified by the FCC with the phone transmitting
at its highest certified power level in all tested frequency
bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the phone
while operation can be well below the maximum value. This
is because the phone is designed to operate at multiple
power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
Before a phone model is available for sale to the public,
it must be tested and certified to the FCC that it does not
exceed the limit established by the government-adopted
requirement for safe exposure. The tests are performed
in positions and locations (e.g., at the ear and worn on the
body) as required by the FCC for each model. (Body-worn
measurements may differ among phone models, depending
upon available accessories and FCC requirements). While
there may be differences between the SAR levels of
various phones and at various positions, they all meet the
government requirement for safe exposure.
For body worn operation, to maintain compliance with FCC
RF exposure guidelines, use only High Tech computer, Corp.
approved accessories. When carrying the phone while it is
on, use the specific High Tech computer, Corp. supplied
or approved carrying case, holster, or other body-worn
accessory.
Use of non High Tech computer, Corp. approved accessories
may violate FCC RF exposure guidelines and should be
avoided.
Regulatory Notice
FCC Compliance Statement
Regulatory Notice
Important Health and Safety
Information
Retain and follow all product safety and operating
instructions. Observe all warn and in the operating
instructions.ings on the product
Avoid pushing objects into product
Never push objects of any kind into cabinet slots or
other openings in the product. Slots and openings are
provided for ventilation. These openings must not be
blocked or covered.
Mounting Accessories
Do not use the product on an unstable table, cart,
stand, tripod, or bracket. Any mounting of the product
should follow the manufacturer's instructions, and
should use a mounting accessory recommended by
the manufacturer.
Avoid unstable mounting
Do not place the product with an unstable base.
Use product with approved equipment
This product should be used only with personal
computers and options identified as suitable for use
with your equipment.
Adjust the volume
Turn down the volume before using headphones or other
audio devices.
Cleaning
Unplug the product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning, but NEVER use water to clean
an LCD screen.
To reduce the risk of bodily injury, electric shock, fire,
and damage to the equipment observe the following
precautions.
a) General Precautions
Heed service markings
Except as explained elsewhere in the Operating or
Service documentation, do not service any product
yourself. Service needed on components inside these
compartments should be done by an authorized service
technicians or provider.
Damage requiring service
Unplug the product from the electrical outlet and
refer servicing to an authorized service technicians or
provider under the following conditions:
l Liquid has been spilled or an object has fallen into
the product.
l The product has been exposed to rain or water.
l The product has been dropped or damaged.
l There are noticeable signs of overheating.
l The product does not operate normally when you
follow the operating instructions.
Avoid hot areas
The product should be placed away from heat sources
such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Avoid wet areas
Never use the product in a wet location.
b) Safety Precautions for
Power Supply Unit
Use the correct external power source
A product should be operated only from the type
of power source indicated on the electrical ratings
label. If you are not sure of the type of power source
required, consult your authorized service provider or
local power company. For a product that operates from
battery power or other sources, refer to the operating
instructions that are included with the product
Handle battery packs carefully
This product contains a Lithium Polymer battery. There
is a risk of fire and burns if the battery pack is handled
improperly. Do not attempt to open or service the battery
pack.
Do not disassemble, crush, puncture, short external
contacts or circuits, dispose of in fire or water, or
expose a battery pack to temperatures higher than
60¢XC (140¢XF).
DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY RE-PLACED. TO REDUCE
RISK OF FIRE OR BURNS, DO NOT
DISASSEMBLE, CRUSH, PUNCTURE, SHORT
EXTERNAL CONTACTS, HEAT ABOVE 100℃
(212℉), OR DISPOSE OF IN FIRE OR
WATER. REPLACE ONLY WITH SPECIFIED
BATTERIES. RECYCLE OR DISPOSE OF
USED BATTERIES ACCORDING TO THE
LOCAL RE-GULATIONS OR REFERENCE
GUIDE SUPPLIED WITH YOUR PRODUCT.
c) Exposure to Radio
Frequency (RF) Signals
Your wireless phone is a radio transmitter and receiver. It
is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by
the Federal Communications Commission of the U.S.
Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy
for the general population. The guidelines are based
on the safety standards previously set by both U.S. and
international standards bodies:
n American National Standards Institute
(ANSI) IEEE. C95.1-1992
n National Council on Radiation Protection
and Measurement (NCRP). Report 86. 1986
n International Commission on Non-Ionizing
Radiation Protection (ICNIRP) 1996
n Ministry of Health (Canada), Safety Code
6. The standards include a substantial safety
margin designed to assure the safety of all
persons, regardless of age and health.
The exposure standard for wireless mobile phones
employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC
is 1.6W/kg *.
*In the U.S. and Canada, the SAR limit for mobile phones
used by the public is 1.6 watts/kg (W/kg) averaged over
one gram of tissue. The standard incorporates a substantial
margin of safety to give additional protection for the public
and to account for any variations in.
d) SAR Information
THIS MODEL DEVICE MEETS THE GOVERN-MENT'S
REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
Your wireless mobile GSM phone is a radio transmitter and
receiver. It is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy
set by the Federal Communications Commission of the
U.S. Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy
for the general population. The guidelines are based on
the saftety standards previously set by both U.S. and
international standards bodies :
n American National Standards Institute
(ANSI) IEEE. C95.1-1992
n National Council on Radiation Protection
and Measurement (NCRP). Report 86. 1986
n International Commission on Non-Ionizing
Radiation Protection (ICNIRP) 1996
Regulatory Notice
Regulatory Notice
For body worn operation, this phone has been tested and
meets the FCC RF exposure guidelines when used with
an accessory that contains no metal and that position the
antenna of the GSM phone a minimum of 1.5cm from the
body. The SAR values of this GSM phone are 0.726W/g
(body) and 0.362W/g (head). Use of other accessories
may not ensure compliance with the FCC RF exposure
guidelines.
The FCC has granted an Equipment Authorization for
this model device with all reported SAR levels evaluated
as in compliance with the FCC RF exposure guidelines.
SAR information on this model device is on file with the
FCC and can be found under the Display Grant section
of http://www.fcc.gov/oet/fccid after searching on FCC
ID: NM8HIMALAYAS. Additional information on Specific
Absorption Rates (SAR) can be found on the Cellular
Telecommunications & Internet Association (CTIA) website as http://www.devicefacts.net.
For More Information
The exposure standard for wireless mobile GSM phone
employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR limit set by the FCC
is 1.6W/kg*.
* In the U.S. and Canada, the SAR limit for mobile GSM
phone used by the public is 1.6Watts/kg (W/kg) averaged
over one gram of tissue. The standard incorporates a
substantial margin of safety to give additional protection
for the public and to account for any variations in.
Microsoft, ActiveSync, Outlook, Pocket Outlook, Windows,
Windows NT, and the Windows logo are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Using for the First Tiem
n Ministry of Health (Canada), Safety
Code 6. The standards include a substantial
safety margin designed to assure the safety
of all persons, regardless of age and health.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2004:02:27 16:53:22-08:00
Create Date                     : 2004:02:27 16:53:00-08:00
Title                           : Andes_QSG.indd
Creator                         : Adobe InDesign 2.0.2
Producer                        : Adobe PDF Library 5.0
Page Count                      : 14
Mod Date                        : 2004:02:27 16:53:22-08:00
Creation Date                   : 2004:02:27 16:53:00-08:00
Metadata Date                   : 2004:02:27 16:53:22-08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools