HUNAN FN LINK TECHNOLOGY F11AUUM13 USB WIFI Module User Manual FN LINK TECHNOLOGY LIMITED

FN-LINK TECHNOLOGY LIMITED USB WIFI Module FN LINK TECHNOLOGY LIMITED

User Manual REV1

FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 1 /9F11AUUM13 series user 's manual
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 2 /9IndexHow to install the driverPut the product plug into the USB port of PC……………………..3Copy the driver into the PC……………..………….…...................3Install the driver & Install driver successfully……….………….....6The test interface……………………………….……......................7
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 3 /91. Put the product plug into the USB port, the "device manager" of PC is shown below:2. Copy the corresponding driver "RTLWlanU_WindowsDriver_1019.0.0518.2012_UI_1.00.0191_EU" into the PC, and install driver, the installation methods: open the file"RTLWlanU_WindowsDriver_1019.0.0518.2012_UI_1.00.0191_EU", double click"Setup" installation program, guide to install.
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 4 /9
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 5 /9
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 6 /9
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 7 /93. After install driver successfully. the "device manager" of PC is shown below:4. After install driver successfully. double click the icon " " in PC desktop, as shownbelow:
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 8 /9FCC Warning:Changes or modifications to this unit not expressly approved by the partresponsible for compliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycause undesired operation.Note: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.Consult the dealer or an experienced radio/TV technician for help.
FN-LINK TECHNOLOGY LIMITEDhttp://www.fn-link.com Page 9 /9IC Notice:This device complies with Canada Industry licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may notcause interference. and (2) this device must accept any interference. Includinginterference that may cause undesired operation of the device.CAN ICES-3 (B)Le présent appareil est conforme aux CNR d'industrie Canada applicables auxappareils radio exem pts de licence L'exploitation est autorisée aux deuxconditions suivantes:1) I'appareil ne doit pas produire de brouillage, et2) I'utillsateur de I'appareil doit accepterbrouillage radioélectrique subi memesi le brouillage est susceptible d'encompromettre le fonctionnement. mauvaisfonctionnement de I'appareil.NMB-3 (B)FCC Radiation Exposure Statement:This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Due to missing shielding the module is strictly limited to integration by the Grantee himself or his dedicated OEM integrator under control of the Grantee.However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.This device is intended only for OEM integrators under the following conditions:1)This module is granted as a Limited Modular Approval.2)This device has been designed to operate with a integral antenna having a maximum gain of 0dBi.Only this type of antenna may be used. This device has been evaluated and shown compliant with the FCC RF Exposure limits under fixed exposure conditions (antennas are greater than 20cm from a person’s body)when installed in certain specific OEM configurations. The host system shall have a label showing: Contains FCC ID:2AATL-F11AUUM13 The wifi module is designed to comply with the FCC statement. FCC ID is 2AATL-F11AUUM13. The host system using wifi module F11AUUM13-W3, F11AUUM13-W2, should have label indicated FCC ID Note: The wifi module has no shielding and tested stand alone.antenna that users can be use: FPC antenna, PCB antenna, integral antenna.This module is tested and approved as Limited modular approval with stand alone configuration, any OEM incorporated this radio module into any system may require additional testing and evaluation.(The gain of antenna : -2 to 0dBi)This module is not sales with antenna, it requires the OEM to complete the antenna. And the kind of 2AATL-F11AUUM13. F11AUUM13-W2 USB WIFI Module Pin 2 9 8 7 6 5 4 1 3 Antenna (Kind of antenna: FPC antenna, PCB antenna, Integral antenna)

Navigation menu