HUNAN FN LINK TECHNOLOGY F89ESSM23 WIFI Module User Manual USE v5

FN-LINK TECHNOLOGY LIMITED WIFI Module USE v5

Contents

User Manual

Product Specification IEEE 802.11b/g/n 1T1R SDIO WiFi Module Project Name RTL8189ES 11n WIFI Module Model NO F89ESSM23-W1 Approved:: SYMEN SONG Check: Jim HU Prepared: SJ LI FN-LINK TECHNOLOGY LIMITD 5th Floor, A Building, Haoye Logistics Park, Shugang Channel, Bao'an District, Shenzhen City, CHINA TEL: 86-0755-29558186 FAX: 86-0755-29558196 Website: www.fn-link.com
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 2/14 3/27/2014 INDEX 0. REVESION HISTORY…………………………………………………………………………....3 1. INTRODUCTION………………………………………………………………………………….4 1.1 OVERVEIW…………………………………….……………………………………………...4 1.2 SPECIFICATION REFERENCE…………………….………………………………….…...4 1.3 SYSTEM CHARACTERISTICS……………………………………………………………...5 2. MECHANICAL SPECIFICATION………………………………………………………………...6 2.1 OUTLINE DRAWING………………………………………………………………………….6 2.2 CONNECTOR PIN DEFENITION……………………………………………………………6 2.3 LAYOUT GUIDLINE…………………………………………………………………………...7 3. RF SPECIFICATION………………………………………………………………………………8 3.1 TRANSMITTER POWER……………………………………………………………………..8 3.2 EVM……………………………………………………………………………………………..8 3.3 TRANSMIT CENTER FREQUENCY TOLERANCE……………………………………….9 3.4 RECEIVER SENSITIVITY………………………………………………………….………....9 3.5 POWER CONSUMPTION…………………………………………………………………....10 4. PACKAGE……………………………………….………………………………………………....11 5. USER’S MANUAL…………………………………………………………………………………12 .
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 3/14 3/27/2014 0. Revision History REV NO Date Modifications Draft Approved Rev1.0 May 11th,2012 XJ Hu Rev1.1 Dec 30th,2013 SJ LI
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 4/14 3/27/2014 1. Introduction F89ESSM23 is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 150 Mbps . 1.1 Overview The general hardware for the module is shown in Figure 1. This WLAN Module design is based on Realtek RTL8189ES. It is a highly integrated single-chip 1*1 MIMO (Multiple In Multiple Out) Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. It is designed to provide excellent performance with low power Consumption and enhance the advantages of robust system and cost-effective. Figure 1: Single-brand 11n (1*1) solution 1.2 Specification Reference This specification is based on additional references listed as below. iEEE 802.11b iEEE 802.11g iEEE 802.11n
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 5/14 3/27/2014 1.3 System Characteristics Main Chipset Realtek RTL8189ES Operating Frequency 2.412～2.462GHz WIFI Standard Ieee802.11b/g/n 1*1 Modulation 802.11b: CCK(11, 5.5Mbps), QPSK(2Mbps), BPSK(1Mbps) 802.11 g/n: OFDM PHY Data rates 802.11b: 11,5.5,2,1 Mbps 802.11g: 54,48,36,24,18,12,9,6 Mbps 802.11n: up to 150Mbps Receiver Sensitivity 130M：-70dBm@10% PER; 108M：-70dBm@10% PER; 54M：-70dBm@10% PER; 11M：-87dBm@8% PER; 6M：-90dBm@10% PER; 1M：-92dBm@8% PER Host Interface SDIO/GSPI Operation Range Up to 150meters in open space RF Power <9.0dBm@11n,<9.8dBm@11b,<9.5dBm@11g RF Antenna Integral Antenna (0dBi gain) OS Support Android / Win CE /iOS /Linux/Windows 2000/XP/Vista/WIN7 Security WEP,TKIP,AES,WPA,WPA2 Power Consumption 3.3Vdc 110mA Max Operating Temperature -20~ +45°C Ambient Temperature Storage Temperature -40~ +70°C Ambient Temperature Humidity 5% to 90% maximum (non-condensing) Dimension Typical L14.00*W12.50*T2.00mm
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 6/14 3/27/2014 2. Mechanical Specification 2.1 Outline Drawing 2.2 Connector Pin Definition Pin # Name Description 1 SD_CMD SDIO Command Input 2 SD_D3 SDIO Data Line 3 3 SD_D2 SDIO Data Line 2 4 SD_D1 SDIO Data Line 1 5 SD_D0 SDIO Data Line 0 6 SD_CLK SDIO Clock Input 7 GND POWER GND 8 GND POWER GND 9 ANTENNA RF OUT 10 WAKE Wake Function 11 VDIOSDIO SDIO Voltage 1.8V-3.3V
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 7/14 3/27/2014 12 3.3 Power Supply 13 CS PDn 2.3 Layout reference
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 8/14 3/27/2014 3. RF Performance 3.1Transmitter Power (Unit in dBm) (Typical 1,6,11 Channel) 11n 20MHz Mode （Spec<9dBm） Mode Rate Channel 1 Channel 6 Channel 11 MCS0 8.5 8.3 8.4 MCS3 8.3 8.4 8.3 MCS5 8.5 8.2 8.5 11n 20MHz MCS7 8.3 8.5 8.4 11n 40MHz Mode ( Spec<9dBm） Mode Rate Channel 1 Channel 6 Channel 11 MCS0 7.6 7.4 7.3 MCS3 7.5 7.2 7.4 MCS5 7.3 7.5 7.6 11n 40MHz MCS7 7.5 7.2 7.3 3.2 EVM 11b Mode: unit in % （Spec≦10%） Mode Rate Channel 1 Channel 6 Channel 11 1Mbps 5.2 5.3 5.5 2Mbps 5.4 5.3 5.5 5.5Mbps 5.6 5.3 5.5 11b CCK 11Mbps 5.9 5.6 5.9 11g Mode: unit in dB （Spec≦-25dB） Mode Rate Channel 1 Channel 6 Channel 11 6Mbps -29.3 -29.5 -29.1 18Mbps -29.2 -28.5 -29.3 36Mbps -28.5 -28.9 -28.1 11g OFDM 54Mbps -29.8 -29.1 -29.0 11n 20MHz Mode: unit in dB（Spec≦-25dB） Mode Rate Channel 1 Channel 6 Channel 11 MCS0 -28.3 -28.5 -28.5 MCS3 -28.2 -29.5 -28.4 MCS5 -28.3 -28.5 -28.1 11n 20MHz MCS7 -28.1 -28.4 -28.0 11n 40MHz Mode: unit in dB （Spec≦-25dB）
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 9/14 3/27/2014 Mode Rate Channel 1 Channel 6 Channel 11 MCS0 -27.3 -27.5 -26.5 MCS3 -27.2 -26.5 -26.4 MCS5 -27.3 -26.5 -26.1 11n 40MHz MCS7 -28.3 -28.2 -28.1 3.3 Transmit Center Frequency Tolerance 11g transmit center frequency tolerance test result: Channel CH6 Result(ppm) 0.65 Frequency tolerance 1.57KHz Pass/Fail PASS 11n transmit center frequency tolerance test result: Channel CH6 Result(ppm) 0.71 Frequency tolerance 1.73KHz Pass/Fail PASS 3.4 Receiver sensitivity (Unit in dBm) 11b Mode: 1RX （Spec≦-75dBm） Mode Rate Channel 1 Channel 6 Channel 11 1Mbps -90 -90 -90 2Mbps -90 -90 -91 5.5Mbps -89 -89 -88 11b 11Mbps -85 -85 -86 11g Mode: 1RX （Spec≦-65dBm） Mode Rate Channel 1 Channel 6 Channel 11 6Mbps -90 -90 -90 9Mbps -90 -90 -91 12Mbps -89 -89 -88 18Mbps -85 -85 -86 24Mbps -78 -79 -78 36Mbps -75 -75 -75 48Mbps -71 -71 -71 11g 54Mbps -69 -68 -70 11n 20MHz Mode: 1RX （Spec≦-65dBm） Mode Rate Channel 1 Channel 6 Channel 11 MCS0 -85 -85 -85 MCS1 -82 -82 -82 11n 20MHz MCS2 -80 -80 -80
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 10/14 3/27/2014 MCS3 -77 -77 -77 MCS4 -73 -74 -74 MCS5 -69 -70 -69 MCS6 -68 -68 -68 MCS7 -66 -66 -66 11n 40MHz Mode: 1RX （Spec≦-60dBm） Mode Rate Channel 1 Channel 6 Channel 11 MCS0 -83 -83 -83 MCS1 -79 -80 -80 MCS2 -77 -77 -77 MCS3 -74 -75 -75 MCS4 -71 -71 -71 MCS5 -67 -67 -67 MCS6 -65 -65 -65 11n 40MHz MCS7 -63 -63 -63 3.5 Power Consumption Mode Status Power(mW) Note 3.3Vx70mA =231 20M Link 3.3Vx75 mA =248 40M 3.3Vx75mA =248 20M RX 3.3Vx75 mA =248 40M 3.3Vx100 mA =330 20M TX 3.3Vx110 mA=363 40M Power save mode 3.3Vx20 mA =66 DTIM=100ms Device Disable 3.3Vx25 mA =82.5 OS Windows XP Radio Off 3.3Vx0 mA =0
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 11/14 3/27/2014 4.0 Package 4.1 blister packaging Remark: 100pcs/Layer, 10Layer/Bag, 1,000pcs/Bag 4.2 the roll package 2,000pcs/roll
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 12/14 3/27/2014 5.0 User’s Manual 5.1 Recommended Reflow curve Referred to IPC/JEDEC standard Peak Temperature : <250°C Number of Times : ≤2 times 5.2 Patch WIFI modules installed before the notice: WIFI module installed note: 1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a stencil 2. Take and use the WIFI module, please insure the electrostatic protective measures. 3. Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 ℃ for the MID motherboard. About the module packaging, storage and use of matters needing attention are as follows: 1. The module of the reel and storage life of vacuum packing: 1). Shelf life: 8 months, storage environment conditions: temperature in: < 40 ℃, relative humidity: < 90% r.h. 2. The module vacuum packing once opened, time limit of the assembly: Card: 1) check the humidity display value should be less than 30% (in blue), such as: 30% ~ 40% (pink), or greater than 40% (red) the module have been moisture absorption. 2.) factory environmental temperature humidity control: ≦ 30% ℃, ≦ 60% r.h.. 3). Once opened, the workshop the preservation of life for 168 hours. 3. Once opened, such as when not used up within 168 hours: 1). The module must be again to remove the module moisture absorption. 2). The baking temperature: 125 ℃, 8 hours. 3.) after baking, put the right amount of desiccant to seal packages.
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 13/14 3/27/2014 FCC ID: 2AATL-F89ESSM23 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. IMPORTANT NOTE: This device is intended only for OEM integrators under the following conditions: (1) According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter must have their own shielding. However, due to there is no shielding for this WIFI Module, this module is granted as a Limited Modular Approval. (2) This module has been designed to operate with a Integral antenna having a maximum gain of 0dBi. Only this type of antenna may be used. (3) Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under control of the Grantee. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter).then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. IMPORTANT NOTE: This module is intended for OEM integrator only and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following “Contains TX FCC ID: 2AATL-F89ESSM23”. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. We hereby requests for part 15 unlicensed limited modular transmitter approval of our device, described as follows: This RF Module does not have an own shielding, so that a Limited Modular Approval (LMA) was granted: This RF module is strictly limited to the integration by the Grantee himself or the dedicated OEM
FN-LINK TECHNOLOGY LIMITED http://www.fn-link.com Page 14/14 3/27/2014 integrators under the control of the Grantee. Proper measurements of the host device including this RF module (radiated spurious emissions and bandedge) are required to assure compliance with the FCC regulations.

Navigation menu