HUNAN FN LINK TECHNOLOGY F89ESSM23 WIFI Module User Manual USE v5

Download:
Mirror Download [FCC.gov]
Document ID	2225980
Application ID	g6RtqU5CeQGsAw/wKRYjsA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.22kB (627742 bits)
Date Submitted	2014-03-26 00:00:00
Date Available	2014-03-26 00:00:00
Creation Date	2014-03-27 09:10:54
Document Lastmod	2014-03-27 09:10:54
Document Title	Microsoft Word - 欧智通-USE-v5.doc
Document Creator	欧智通-USE-v5.doc - Microsoft Word
Document Author:	EMC TEST

FN-LINK TECHNOLOGY LIMITD
5th Floor, A Building, Haoye Logistics Park,
Shugang Channel, Bao'an District,
Shenzhen City, CHINA
TEL: 86-0755-29558186
FAX: 86-0755-29558196
Website: www.fn-link.com
Product Specification
IEEE 802.11b/g/n 1T1R SDIO WiFi Module
Project Name
RTL8189ES 11n WIFI Module
Model NO
F89ESSM23-W1
Approved:: SYMEN SONG
Check: Jim HU
Prepared: SJ LI
FN-LINK TECHNOLOGY LIMITED
INDEX
0. REVESION HISTORY…………………………………………………………………………....3
1. INTRODUCTION………………………………………………………………………………….4
1.1 OVERVEIW…………………………………….……………………………………………...4
1.2 SPECIFICATION REFERENCE…………………….………………………………….…...4
1.3 SYSTEM CHARACTERISTICS……………………………………………………………...5
2. MECHANICAL SPECIFICATION………………………………………………………………...6
2.1 OUTLINE DRAWING………………………………………………………………………….6
2.2 CONNECTOR PIN DEFENITION……………………………………………………………6
2.3 LAYOUT GUIDLINE…………………………………………………………………………...7
3. RF SPECIFICATION………………………………………………………………………………8
3.1 TRANSMITTER POWER……………………………………………………………………..8
3.2 EVM……………………………………………………………………………………………..8
3.3 TRANSMIT CENTER FREQUENCY TOLERANCE……………………………………….9
3.4 RECEIVER SENSITIVITY………………………………………………………….………....9
3.5 POWER CONSUMPTION…………………………………………………………………....10
4. PACKAGE……………………………………….………………………………………………....11
5. USER’S MANUAL…………………………………………………………………………………12
http://www.fn-link.com
Page 2/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
0. Revision History
REV NO
Date
Modifications
Rev1.0
May 11 ,2012
Rev1.1
Dec 30 ,2013
Draft
Approved
th
XJ Hu
th
SJ LI
http://www.fn-link.com
Page 3/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
1. Introduction
F89ESSM23 is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO
network interface device. High-speed wireless connection up to 150 Mbps .
1.1 Overview
The general hardware for the module is shown in Figure 1. This WLAN Module design is based
on Realtek RTL8189ES. It is a highly integrated single-chip 1*1 MIMO (Multiple In Multiple Out)
Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n
specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. It is
designed to provide excellent performance with low power Consumption and enhance the
advantages of robust system and cost-effective.
Figure 1: Single-brand 11n (1*1) solution
1.2 Specification Reference
This specification is based on additional references listed as below.
iEEE 802.11b
iEEE 802.11g
iEEE 802.11n
http://www.fn-link.com
Page 4/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
1.3 System Characteristics
Main Chipset
Realtek RTL8189ES
Operating Frequency
2.412～2.462GHz
WIFI Standard
Ieee802.11b/g/n 1*1
Modulation
802.11b: CCK(11, 5.5Mbps), QPSK(2Mbps), BPSK(1Mbps)
802.11 g/n: OFDM
PHY Data rates
802.11b: 11,5.5,2,1 Mbps
802.11g: 54,48,36,24,18,12,9,6 Mbps
802.11n: up to 150Mbps
Receiver Sensitivity
130M：-70dBm@10% PER; 108M：-70dBm@10% PER; 54M：
-70dBm@10% PER; 11M：-87dBm@8% PER; 6M：-90dBm@10%
PER; 1M：-92dBm@8% PER
Host Interface
SDIO/GSPI
Operation Range
Up to 150meters in open space
RF Power
<9.0dBm@11n,<9.8dBm@11b,<9.5dBm@11g
RF Antenna
Integral Antenna (0dBi gain)
OS Support
Android / Win CE /iOS /Linux/Windows 2000/XP/Vista/WIN7
Security
WEP,TKIP,AES,WPA,WPA2
Power Consumption
3.3Vdc 110mA Max
Operating Temperature -20~ +45°C Ambient Temperature
Storage Temperature
-40~ +70°C Ambient Temperature
Humidity
5% to 90% maximum (non-condensing)
Dimension
Typical L14.00*W12.50*T2.00mm
http://www.fn-link.com
Page 5/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
2. Mechanical Specification
2.1 Outline Drawing
2.2 Connector Pin Definition
Pin #
Name
Description
SD_CMD
SDIO Command Input
SD_D3
SDIO Data Line 3
SD_D2
SDIO Data Line 2
SD_D1
SDIO Data Line 1
SD_D0
SDIO Data Line 0
SD_CLK
SDIO Clock Input
GND
POWER GND
GND
POWER GND
ANTENNA
RF OUT
10
WAKE
Wake Function
11
VDIOSDIO
SDIO Voltage 1.8V-3.3V
http://www.fn-link.com
Page 6/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
12
3.3
Power Supply
13
CS
PDn
2.3 Layout reference
http://www.fn-link.com
Page 7/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
3. RF Performance
3.1Transmitter Power (Unit in dBm) (Typical 1,6,11 Channel)
11n 20MHz Mode （Spec<9dBm）
Mode
11n
20MHz
Rate
Channel 1
Channel 6
Channel 11
MCS0
8.5
8.3
8.4
MCS3
8.3
8.4
8.3
MCS5
8.5
8.2
8.5
MCS7
8.3
8.5
8.4
Rate
Channel 1
Channel 6
Channel 11
MCS0
7.6
7.4
7.3
MCS3
7.5
7.2
7.4
MCS5
7.3
7.5
7.6
MCS7
7.5
7.2
7.3
Rate
Channel 1
Channel 6
Channel 11
1Mbps
5.2
5.3
5.5
2Mbps
5.4
5.3
5.5
5.5Mbps
5.6
5.3
5.5
11Mbps
5.9
5.6
5.9
Rate
Channel 1
Channel 6
Channel 11
6Mbps
-29.3
-29.5
-29.1
18Mbps
-29.2
-28.5
-29.3
36Mbps
-28.5
-28.9
-28.1
54Mbps
-29.8
-29.1
-29.0
11n 40MHz Mode ( Spec<9dBm）
Mode
11n
40MHz
3.2 EVM
11b Mode: unit in % （Spec≦10%）
Mode
11b
CCK
11g Mode: unit in dB （Spec≦-25dB）
Mode
11g
OFDM
11n 20MHz Mode: unit in dB（Spec≦-25dB）
Mode
11n
20MHz
Rate
Channel 1
Channel 6
Channel 11
MCS0
-28.3
-28.5
-28.5
MCS3
-28.2
-29.5
-28.4
MCS5
-28.3
-28.5
-28.1
MCS7
-28.1
-28.4
-28.0
11n 40MHz Mode: unit in dB （Spec≦-25dB）
http://www.fn-link.com
Page 8/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
Mode
11n
40MHz
Rate
Channel 1
Channel 6
Channel 11
MCS0
-27.3
-27.5
-26.5
MCS3
-27.2
-26.5
-26.4
MCS5
-27.3
-26.5
-26.1
MCS7
-28.3
-28.2
-28.1
3.3 Transmit Center Frequency Tolerance
11g transmit center frequency tolerance test result:
Channel
CH6
Result(ppm)
0.65
Frequency tolerance
1.57KHz
Pass/Fail
PASS
11n transmit center frequency tolerance test result:
Channel
CH6
Result(ppm)
0.71
Frequency tolerance
1.73KHz
Pass/Fail
PASS
3.4 Receiver sensitivity (Unit in dBm)
11b Mode: 1RX （Spec≦-75dBm）
Mode
11b
Rate
Channel 1
Channel 6
Channel 11
1Mbps
-90
-90
-90
2Mbps
-90
-90
-91
5.5Mbps
-89
-89
-88
11Mbps
-85
-85
-86
Rate
Channel 1
Channel 6
Channel 11
6Mbps
-90
-90
-90
9Mbps
-90
-90
-91
12Mbps
-89
-89
-88
18Mbps
-85
-85
-86
24Mbps
-78
-79
-78
36Mbps
-75
-75
-75
48Mbps
-71
-71
-71
54Mbps
-69
-68
-70
11g Mode: 1RX （Spec≦-65dBm）
Mode
11g
11n 20MHz Mode: 1RX （Spec≦-65dBm）
Mode
Rate
Channel 1
Channel 6
Channel 11
11n
20MHz
MCS0
-85
-85
-85
MCS1
-82
-82
-82
MCS2
-80
-80
-80
http://www.fn-link.com
Page 9/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
MCS3
-77
-77
-77
MCS4
-73
-74
-74
MCS5
-69
-70
-69
MCS6
-68
-68
-68
MCS7
-66
-66
-66
Rate
Channel 1
Channel 6
Channel 11
MCS0
-83
-83
-83
MCS1
-79
-80
-80
MCS2
-77
-77
-77
MCS3
-74
-75
-75
MCS4
-71
-71
-71
MCS5
-67
-67
-67
MCS6
-65
-65
-65
MCS7
-63
-63
-63
11n 40MHz Mode: 1RX （Spec≦-60dBm）
Mode
11n
40MHz
3.5 Power Consumption
Mode
Status
Power(mW)
Note
Link
3.3Vx70mA =231
20M
3.3Vx75 mA =248
40M
3.3Vx75mA =248
20M
3.3Vx75 mA =248
40M
3.3Vx100 mA =330
20M
3.3Vx110 mA=363
40M
Power save mode
3.3Vx20 mA =66
DTIM=100ms
Device Disable
3.3Vx25 mA =82.5
Radio Off
3.3Vx0 mA =0
RX
OS
Windows XP
http://www.fn-link.com
TX
Page 10/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
4.0 Package
4.1
blister packaging
Remark: 100pcs/Layer, 10Layer/Bag, 1,000pcs/Bag
4.2
the roll package
2,000pcs/roll
http://www.fn-link.com
Page 11/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
5.0 User’s Manual
5.1 Recommended Reflow curve
Referred to IPC/JEDEC standard
Peak Temperature : <250°C
Number of Times : ≤2 times
5.2 Patch WIFI modules installed before the notice:
WIFI module installed note:
1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a
stencil
2. Take and use the WIFI module, please insure the electrostatic protective measures.
3. Reflow soldering temperature should be according to the customer the main size of the products, such
as the temperature set at 250 + 5 ℃ for the MID motherboard.
About the module packaging, storage and use of matters needing attention are as follows:
1. The module of the reel and storage life of vacuum packing: 1). Shelf life: 8 months, storage
environment conditions: temperature in: < 40 ℃, relative humidity: < 90% r.h.
2. The module vacuum packing once opened, time limit of the assembly:
Card: 1) check the humidity display value should be less than 30% (in blue), such as: 30% ~ 40% (pink),
or greater than 40% (red) the module have been moisture absorption.
2.) factory environmental temperature humidity control: ≦ 30% ℃, ≦ 60% r.h..
3). Once opened, the workshop the preservation of life for 168 hours.
3. Once opened, such as when not used up within 168 hours:
1). The module must be again to remove the module moisture absorption.
2). The baking temperature: 125 ℃, 8 hours.
3.) after baking, put the right amount of desiccant to seal packages.
http://www.fn-link.com
Page 12/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
FCC ID: 2AATL-F89ESSM23
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT NOTE:
This device is intended only for OEM integrators under the following conditions:
(1) According to FCC Part 15 Subpart C Section 15.212, the radio elements of the modular transmitter
must have their own shielding. However, due to there is no shielding for this WIFI Module, this module is
granted as a Limited Modular Approval.
(2) This module has been designed to operate with a Integral antenna having a maximum gain of 0dBi.
Only this type of antenna may be used.
(3) Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under
control of the Grantee.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter).then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
IMPORTANT NOTE:
This module is intended for OEM integrator only and the OEM integrators are instructed to ensure that
the end user has no manual instructions to remove or install the device. The OEM integrator is still
responsible for the FCC compliance requirement of the end product, which integrates this module.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following “Contains TX FCC ID:
2AATL-F89ESSM23”. If the size of the end product is smaller than 8x10cm, then additional FCC part
15.19 statement is required to be available in the users manual: This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
We hereby requests for part 15 unlicensed limited modular transmitter approval of our device, described
as follows:
This RF Module does not have an own shielding, so that a Limited Modular Approval (LMA) was granted:
This RF module is strictly limited to the integration by the Grantee himself or the dedicated OEM
http://www.fn-link.com
Page 13/14
3/27/2014
FN-LINK TECHNOLOGY LIMITED
integrators under the control of the Grantee.
Proper measurements of the host device including this RF module (radiated spurious emissions and
bandedge) are required to assure compliance with the FCC regulations.
http://www.fn-link.com
Page 14/14
3/27/2014

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 14
Modify Date                     : 2014:03:27 09:10:54+08:00
Create Date                     : 2014:03:27 09:10:54+08:00
Title                           : Microsoft Word - 欧智通-USE-v5.doc
Author                          : EMC TEST
Creator                         : 欧智通-USE-v5.doc - Microsoft Word

EXIF Metadata provided by EXIF.tools