HYT Science and Technology Co TR-800U1 REPEATER (BASE STATION) User Manual User s Manual Add Information

Shenzhen HYT Science &Technology; Co Ltd REPEATER (BASE STATION) User s Manual Add Information

Contents

USERS MANUAL

SAFETYTRAINING INFORMATION  Your  HYT  radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your HYT  radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:   FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.   American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.   American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.   The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.   To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:  DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.  DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.
 ALWAYS keep the antenna at least 150 cm away from the body when transmitting    The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this radio.  Electromagnetic Interference/Compatibility During transmissions, your HYT radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.  Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.  IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver  SAVE THIS INSTRUCTION MANUAL- This instruction manual contains important operating instructions for the Two-Way Radio  EXPLICIT DEFINITIONS WORD DEFINITION WARNING  Personal injury, fire hazard or electric shock may occur. CAUTION  Equipment damage may occur. NOTE  If disregarded, inconvenience only. No risk of personal injury, fire or electric shock.
OPERATING NOTES   When transmitting, Please Keep the antenna at least 150 cm from your head and body.  PRECAUTIONS WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 150 cm away from the antenna.   WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels.   DO NOT push the PTT when not actually desiring to transmit.   AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F). DO NOT modify the transceiver for any reason.   FCC CAUTION: Changes or modifications to this device, not expressly approved by HYT, could void your authority to operate this transceiver under FCC regulations.
 Revision History   P/N Release Date Revision   Initial Release      General Manual Scope This manual is intended for use by experienced technicians familiar with similar types of communication equipment. It contains all service information required for the equipment and is current as of the publication date. Safety and General Information The following general safety precautions as would normally apply, should be observed during all phases of operation, service and repair of this equipment. ◇  This equipment should be serviced by qualified technicians only. ◇  Do not modify the repeater for any reason. ◇  To avoid electromagnetic interference and/or compatibility conflicts, do not operate your repeater when you are near 380V AC mains or above. ◇  For vehicles with an air bag, do not place a repeater in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a repeater is placed in the air bag deployment area and the air bag inflates, the repeater may be propelled with great force and cause serious injury to occupants of the vehicle. ◇  Turn off your repeater prior to entering any area with a potentially explosive atmosphere. ◇  To avoid possible interference with blasting operations, turn off your repeater when you are near electrical blasting caps, in a blasting area, or in areas posted: “Turn off two-way radio.” Obey all signs and instructions. ◇  Do not charge your back-up battery in a potentially explosive atmosphere ◇  Do not expose the repeater to direct sunlight over a long time, nor place it close to heating source.
                                                           TR-800 Service Manual  -1-◇  Do not place the repeater in excessively dusty, humid areas, nor on unstable surfaces ◇  Connect to the lightning arrester prior to the antenna which is installed    outdoors, and the chassis or equipment housing must be connected to an absolute earth ground, to minimize any possible shock hazard from lightning strike. ◇  Please make sure no stress on the antenna joint during transportation or installation. Caution: This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the owner’s manuals, can cause interference to radio communications.  HYT endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the above specifications and design are subject to change without notice due to continuous development. No part of this manual may be copied, reproduced, translated, stored in a retrieval system, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of HYT.
                                                           TR-800 Service Manual  -2- Brief Introduction              1. Speaker ① 2. LED Indicators Red LED   ②lights while the main radio is transmitting, and flashes while receiving.   Green LED ③ lights while the slave radio is transmitting, and flashes while receiving.   Dark red LED ④ lights while DC power supplies and the AC power fails.   Orange LED ⑤ lights while the repeater in setup state and goes out while in knockdown state.   Blue LED ⑧ lights while the RPT/OPT is active, and goes out while inactive. 3. Repeater Setup/Knockdown ⑥ The setup button is a momentary contact switch that enables or disables the main radio of TR-800. 4. LCD Display ⑦ Display current channel number, frequency, power level, receive status, etc. 5.  Power Switch/Volume Control Knob ⑨ The power switch is located in the center of the knob, short press of which turns repeater on, and long press for 1 second turns repeater off. Rotate the volume control knob clockwise or counter-clockwise to adjust the volume for a    desired level. 6. Microphone Hook ○10    7.  RPT Button, OPT Button   Press the RPT button○12   to enable uni-directional repeater, and press the OPT button  ○11 to enable bi-directional repeater. 8.  Scan Button, Monitor Button Press the Scan button ○16 to initiate repeater scan, which can be activated only when in 1171615121119TX RX BATRPT OPTMONI SCAN UP DN234567891310141820212223242526
                                                           TR-800 Service Manual  -3-uni-directional mode (forward directional, i.e., RPT is active while OPT is inactive).   Short press the Monitor button○17   to display channel frequency by turns of slave radio Rx frequency, slave radio Tx frequency, main radio Rx frequency, main radio Tx frequency; long press it to monitor the activities on the current channel. The main radio processes monitoring while OPT is active, the slave radio processes monitoring while OPT is inactive. 9. “Up” Button ○15 , “Down” Button○13  Press the “Up” or “Down” button to select a desired channel. 10. RJ45 Connector  ○14  Plug the desktop microphone or palm microphone into this port to input audio, or plug the programming cable into this port to program both radios.   11. Antenna Connector The N connector○19   is for connecting with the main radio’s antenna, while the BNC connector○18 is for the slave radio’s antenna. When using duplexer, choose the correct adaptor on the back of TR-800 according to your antenna connector type. 12. Fan  ○20  The fan is temperature-controlled with continuously variable speed as temperature changes. 13. AC Power Inlet○21  (with Switch○22 ) 14. Accessory Connector  ○23  (DB15/F) Used for external controller or link equipment. 15. Grounding Lug  ○24  For lightning protection, this terminal must be connected to an absolute earth ground via thick copper wire, or use lightning arrester if necessary. 16. DC Power Inlet  ○25  The power supply would auto-revert to backup battery once the AC mains fails. This DC port also provides floating charge function with approximate 400mA current. 17. DC Fuse  ○26  The 15A/32Vdc fuse protects against battery polarity reversal.
                                                           TR-800 Service Manual  -4- Software Specification Basic Operation Short press the power switch to turn on the repeater; rotate the volume control knob clockwise to adjust the volume for a comfortable listening level. Press the “Up” or “Down” button to select a desired channel, then the repeater operates as you set.   1.  To achieve the basic repeater functions, the radio must be in the repeater setup, and operates in the uni-directional or bi-directional repeater mode.   Repeater Hang Time When the repeater stops receiving upon signal off, the transmitter remains transmitting for a programmed time period, which reduces delay on conversation due to the setup of repeater link. The repeater Hang Time can be activated when in forward directional repeater only.  Frequency Display Short press the Monitor button displays the frequency in the turn of: slave radio Rx frequency, slave radio Tx frequency, main radio Rx frequency, main radio Tx frequency.  Monitor If the Monitor function is set by your dealer, long press the programmed Monitor key while in receive mode, to hear activities on current channel. The monitor function is disabled while in the bi-directional repeater mode. Four operation modes listed below are provided for you to choose via the programming software. A. Carrier Squelch-Momentary Hold down the Monitor key to open CTCSS/CDCSS/DTMF/2-Tone/5-Tone signalling squelch. Release it to close the signalling squelch. B. Carrier Squelch-Toggle Press the Monitor key to open CTCSS/CDCSS/DTMF/2-Tone/5-Tone signalling squelch. Press it again to close the signalling squelch. C. Squelch Off-Momentary       Hold down the Monitor key to open carrier squelch; release it to close the carrier squelch. D. Squelch Off-Toggle Long press the Monitor key to open carrier squelch. Press it again to close the carrier squelch.  Scan The Scan function can be activated while in the forward directional repeater mode only. Press the Scan
                                                           TR-800 Service Manual  -5-button to initiate repeater scan (if scan parameter is applicable). The Scan Interval Time and Dropout Delay Time are configurable via the programming software.  Signalling Squelch This feature can be enabled/disabled by your dealer. If the feature is enabled, the preset DTMF/2-Tone /5-Tone will control repeater mute/unmute. The repeater will not unmute until valid signalling is received.  CTCSS/CDCSS Set up talkgroups/users with unique CTCSS/CDCSS to prevent unwanted conversations on the same frequency. If CTCSS/CDCSS is set on current channel, a CTCSS/CDCSS match will be required on an incoming call. If not set, the radio unmutes to all calls within the communication range on current channel. Your dealer may preset CTCSS/CDCSS on certain channels.   Note: This feature does not mean that your conversation will not be heard by others.  Time-out Timer (TOT) The feature allows for efficient use of channels by limiting the maximum time of each transmission. It protects the radio from damage caused by long time transmission. Once a continuous transmission exceeds the preset time (15~1200s programmable), the transmission will be automatically terminated and alert tone will be heard. The alert tone ceases upon the release of the PTT.  Selectable Squelch Level (SQL)  Squelch levels from 0 to 9 are selectable via the programming software.  Voice Compander/Scrambler The voice compander/scrambler feature may be enabled/disabled via the programming software. The emphasis/de-emphasis function needs to be disabled while the scrambler feature is enabled, and enabled while the scrambler feature is disabled.  High/Mid/Low Power Programmable High/Med/Low power is selectable via the programming software.  Programmable Channel Spacing A wide/narrow channel spacing is selectable via the programming software.
                                                           TR-800 Service Manual  -6-                  Repeater Modes
                                                           TR-800 Service Manual  -7-Knockdown ModeSetup ModeBase Station Forward Directional RepeaterReverse Directional Repeater Bi-directional RepeaterPC Programming Mode  Modes Description Mode  Description Knockdown Press the SETUP button while the repeater is power on. The repeater enters knockdown mode once the orange LED goes out. Base Station Press RPT and OPT buttons when the SETUP orange LED is on. The radio enters base station mode once both the RPT and OPT blue LEDs go out. Forward Directional Repeater Press RPT and OPT buttons when SETUP orange LED is on. The repeater enters forward directional mode once the RPT blue LED is on while the OPT blue LED goes out. Reverse Directional Repeater Press RPT and OPT buttons when the SETUP orange LED is on. The repeater enters reverse directional mode once the RPT blue LED goes out while the OPT blue LED is on. Setup Bi-directional Repeater Press RPT and OPT buttons when the SETUP orange LED is on. The repeater enters bi-directional repeater mode once both the RPT and OPT blue LEDs is on. PC Programming The repeater enters PC programming mode once command is received from PC, while the SETUP orange LED is on.     Repeater Setup/Knockdown
                                                           TR-800 Service Manual  -8-Press the SETUP button located on the front panel to toggle between repeater setup and knockdown, with LED indications. While in setup state, both radios turn on at power up; in knockdown state, only receive radio turns on at power up. There are three repeater types: base station, uni-directional and bi-directional in the repeater setup state. The repeater is initialized to base station mode when it toggles from knockdown to setup state. But in the knockdown state, the repeater works only as a receiver. In base station mode, the repeater function is disabled, with the slave radio as a receiver and the main radio as a transmitter. In bi-directional repeater mode, the front panel PTT is disabled. The repeater setup/knockdown status will be recorded after the repeater power failure. (E.g. If the repeater operates in forward directional mode, it will still work in such mode after the power recovers)    PC Programming Mode Connect the PC with the repeater via programming cable. Data can be transmitted from PC to the repeater. Repeater LCD displays “PROGRAMMING” while reading/writing data from/into the radio, with red LED flashes indicating programming the main radio, and then green LED flashes indicating programming the slave radio. The repeater resets automatically after programming is finished.  LCD Display  LCD Icon Description Indicator  Description   1.  Displays zone/channel number 2. Displays zone/channel name up to 12 alphanumeric characters (preprogrammed by your dealer) 3.  Displays channel frequency 4.  Displays preprogrammed function   1.  Displays zone/channel number 2.  Displays transmit power level (the 4th digit: H, M, L) 3.  Displays preprogrammed function
                                                           TR-800 Service Manual  -9- Appears when the current channel is already in use    Appears when the Monitor key is pressed to disable CTCSS/DCS, DTMF, 2-Tone/5-Tone decoding.    Appears when the repeater is unmuted upon the monitor key is pressed.   A  Indicates the feature development feature.   SCAN  Appears while repeater scanning.   CALL  Appears when transmitting a selective call.  Appears when a message is received.  Reserved  Reserved  LED Indicator LEDs indicate real-time radio status shown as the following table: LED  Description  Indicates: Tx Red 1.  Lights while the main radio is transmitting. 2.  Flashes while the main radio is receiving. 3.  Flashes while the main radio is monitoring channel activities. 4.  Flashes while programming the main radio.   Rx Green 1.  Lights while the slave radio is transmitting. 2.  Flashes while the slave radio is receiving. 3.  Flashes while the slave radio is monitoring channel activities. 4.  Flashes while programming the slave radio. RPT  Blue, ultra bright 1.  Lights while the RPT is active. 2.  Goes out while the RPT is inactive.
                                                           TR-800 Service Manual  -10-OPT  Blue, ultra bright 1.  Lights while the OPT is active. 2.  Goes out while the OPT is inactive. SETUP Orange 1.  Lights while in the Setup state. 2.  Goes out while in the Knockdown state. BAT Dark red 1.  Lights while the backup battery supplies power. 2.  Goes out while the AC mains supplies power.
                                                           TR-800 Service Manual  -11-  Circuit Description Repeater Communication Interface & Display Unit Theory of Operation  Setup/Knockdown (U0107D, Q0101, Q0103, Q0106, Q0107 and Q0108): The Setup/Knockdown state at power-up can be configured via HR-800 programming software. The electronic switch, Q0106 and Q0108, causes the Setup/Knockdown action by applying or removing voltage at the ignition control, pin15, of “J0102-Main”. After power-up, the Setup or Knockdown state may be changed remotely with a signal from   pin10 of “J4-Slave” or locally through the front panel SETUP. S0102 is a momentary contact switch that is debounced by the Q0103/Q0107 latch circuit. The orange “SETUP” LED, CR0102, illuminates to indicate the Setup state. As the Setup/Knockdown circuit goes from the Knockdown to the Set-up state, Q1 is momentarily turned on by Q0108 via the C0101/R0103 timing circuit. The push to talk (PTT) input of the slave radio, pin8 of “J4-Slave” is pulled low by Q0101 and keys the transmitter. The “Rx” LED, CR0105, will briefly flash during the moment that Q0101 is conducting. Forward Audio Routing (U0103A, U0104A, U0104D and U0105A): The audio gate, U0104D, quarter of an analog switch BU4066B, enables and disables the audio from front panel MIC audio input. U0104D is turned on with an active dc level high driven at the output of NAND gate U0103A-3 by the front panel PTT input. The salve radio audio output from pin5 of “J0104-Slave” is routed to a potentiometer, RV0101. The output of RV0101 is applied to another switch U0104A. U0104A is enabled once a valid signal is received and will route the audio to transmitter. The external audio input, ACC Relay audio, is routed to another potentiometer, RV0103. The output of RV0103 is applied to the second half of U0105, an operational amplifier NJM2904. U0105A, R1106 and R0118 make a buffer amplifier for the link audio. All the “forward” audio will mix together and route through S0101-5 to the main microphone transmitter audio, pin2 of “J0106-Main”. Reverse Audio Routing (U0104B and U0104C): Part of front panel MIC audio is routed to the input of U0104B, quarter of the analog switch BU4066B. The output of U0104B is also controlled with an active low input by the front panel PTT. Audio present on pin5 of “J0102-Main” is routed through S0102-7 to a potentiometer, RV0102, which is used to adjust the audio level for proper deviation. As with the forward direction, the audio output of RV0102 is applied to an analog switch U0106A. This switch turns on only if a valid signal is detected and pin6 of U0104 goes high. Forward and Reverse Key-up (Q0102, U0103, U0107, Q0105, Q0111 and Q0116): When a valid input signal is present at the slave radio, pin6 of “J0104-Slave” will be pulled low and turn off Q0105 through two NAND gates, U0107B and U0107C, along with RPT enable trigger. A dc level high output from Q0105 will be applied to pin37 of U0110 and keys the main radio PTT through output from pin12. The red “Tx” LED, CR0106, illuminates. When the reverse key-up function is enabled, as in the bi-directional repeater configuration, S0101-8 must be on. Q0116 is a dc amplifier (buffer) for the Rx Carrier signal from pin6 of “J0102-Main”. An active
                                                           TR-800 Service Manual  -12-low state at the input of the NAND gate U0107A, one quarter of a MC14011B, will be conversed to a high state to drive the buffer for the Rx Carrier signal. The active low level of Rx Carrier signal, along with the OPT enable signal, cause a series of NAND gates, U0103D, U0103C and U0103B to generate a high dc level to turn on Q0102. The output of Q0102 is pulled low for pin8 of “J0104-Slave” and keys the transmitter of slave radio. The green “Rx” LED, CR0105, illuminates. Q0111 is used to prevent the simultaneous active state on PTT and Rx Carrier signal of “J0102-Main”, which possibly causes unwanted tie condition of keying of both radios.   Accessory D-SUB 15pin receptacle (“J0103-Acc”) The accessory D-Sub, “J0103-ACC”, is connected to “J0102-Main” and “J0104-Slave” to supply Rx audio and PTT for linked radios (repeaters) or external controllers. Receive audio and PTT activation from the linked facilities are applied to the repeater for transmission. Display Unit (U0110, PB01-PB06, K02, Q0113 and Q0118) All the functional triggers of enable and disable come from keypad PB01 to PB06. K02 is an encoder switch for front speaker audio output adjustment. A high output from pin37 of CPU U0110 will turn Q0119 on, driving the base of Q0118 to go low. The backlight LED for the keypad, CR0107, CR0108, CR0111-CR0114 illuminate. Another backlight driver, Q0113, is controlled by Q0114 through the output from pin17 of U0110. Peripheral Circuitry (U0108, U0109, KR00 and KR03) Operating power bus for all the electronics originates from the switch power 13.8Vdc output, pin9 of “J0107-Slave”, and goes through U0109 and U0108 to obtain the reference voltages of 9Vdc and 5Vdc.   KR00 is a DPDT relay driven by transistor Q0123. The output from pin25 of U0110 will turn on/off Q0123, which activates relay KR00 to toggle the front speaker audio routes from slave radio or from main radio. KR03 is another SPDT relay for audio test requirement. A dc level high output from pin26 of U0110 will turn on Q0124 and keys relay KR03. The receive audio to the speaker is blocked and routes only to pin8 of the front RJ45 connector J0109.  IMPORTANT NOTE  Using CTCSS or CDCSS tones may have a lower probability to open squelch than carrier operation. But the CTCSS codes near 100Hz and 150Hz have a high false opening probability due to 50Hz AC power harmonics. Countries having 60Hz AC power may have false opening on 120Hz and 180Hz. CTCSS code 254.1Hz has a high probability of squelch tails.
                                                           TR-800 Service Manual  -13-Figure  Block DiagramⅠ
                                                           TR-800 Service Manual  -14-Power Management Theory of Operation Battery Revert Circuit: A voltage reference network consisting of CR0212, CR0213, R0268, and VR0209 provides a stable voltage reference of 7.5Vdc. This reference voltage, at the anode of VR0209, is applied to the negative input of the Over Voltage Detector U0206B-6, to the positive input of AC Fail Detector U0206A-3, and to the positive input of the Low Battery Detector U0205B-5. Operating positive supply voltage for the integrated circuits is obtained from the TR-800 power supply through CR0212 when the TR-800 is operating on AC mains input power. The supply voltage is obtained through CR02013 when the station is operating on the battery. During normal operation under AC mains power, the negative input of the AC Fail Detector U0206A-2 is more positive than the positive input U0206A-3. The output of U0206A-1 is low and Q0224, the driver for relay KR01, and Q0216, the “BATTERY ON” driver, are turned off. When AC mains power is lost, the voltage at U0206A-2 becomes lower than the reference voltage applied to U0206A-3. The output at U0206A-1 then goes high and turns on both Q0224, which activates relay KR01 and transistor Q0216, which provides a low at the output point “BATTERY ON”. The “BAT ON” LED, CR0219, illuminates to indicate the DC power supply is operating. If the battery voltage falls below approximately 10.2Vdc, the output at U0205B-7 will go high. This action turns on Q0218 that shunts the base drive to Q0224 through CR0217 and turns off the relay. Q0218 also provides a low through CR0218 at output point “BAT LOW”. This auxiliary output might be used to key a portable radio to signal the repeater operator that the battery has exceeded the low voltage limit for the radios. Hysteresis is provided by the feedback network consisting of CR0221, R0289 and R0288 from the output of U0205B-7 to the positive input U0205B-5. The reference voltage at the positive input of U0205B-5 is increased such that the battery voltage must rise above 12Vdc before relay KR01 will reactivate and place the TR-800 back on battery power. This latching action is used to prevent excessively deep discharging of the battery. The repeater will remain turned off until either AC mains return or a charged battery is substituted for the discharged battery. The circuit consisting of C0233, R0285, R0286, CR0220, R0287 and Q0217 resets U0205B-7 to low upon the return of the AC mains power. Capacitor C0234 at the negative input of U0205B-6 smoothes the variation in the battery voltage between the transmit radio keyed and unkeyed conditions. Capacitor C0230 at U0206A-2 input, in conjunction with C0234 at U0205B-6, ensures proper resetting of U0205B with the return of the AC mains power. The Over Voltage Detector consisting of U0206B and resistors R0274, R0275 and R0271 monitors the DC output of the TR-800 power supply. If the voltage exceeds 16.4Vdc, the output of U0206B-7 goes high and turns on relay driver Q0224. The station switches to battery power although there is no indication at the “BAT ON” output point. Zener diodes VR0210, VR0211, VR0212, VR0215 and VR0216 protect the electronics from damage by accidental static discharge. Fuse F0203-15A and diode and CR0215 provide protection from reverse polarity if the battery is inadvertently connected “backward”.
                                                           TR-800 Service Manual  -15-Variable speed, Temperature controlled Fan Circuit: The TL431AILP is a three-terminal programmable shunt regulator diode. This monolithic IC voltage reference operates as a low temperature coefficient zener that is programmed from 6Vdc to 12Vdc with a resistor network consisting of R0296, R0297 and an NTC thermistor Rth0201. Q0219 operates as a fast power switch between “ON” and “OFF” (similar to PWM mode) controlled by the output at cathode of TL431AILP. The rotating speed of brushless fan is voltage controlled at collector of Q0219. The higher temperature, the higher power supply to the fan, hence the faster it rotates. Battery charging (Float Maintenance) Circuit: The battery charging circuit is intended for use with sealed lead acid gel cell batteries. The charging current, limited to approximately 400mA, is used to maintain a “float” charging condition on the battery. After operating the TR-800 station on the battery for long periods of time, or if the battery reaches the low battery limit of the revert circuit, the battery must be recharged with an external high-current charger. Recharging with the internal trickle charger requires an extended period of time. The trickle charging voltage is derived from AC mains. Resistors R0269 limit the charging current to approximately 400mA to a partially discharged battery (terminal voltage of 12Vdc). Once the battery is fully charged, the current will decrease to 10 to 25mA to float the battery at a terminal voltage of 13.6Vdc.  NOTE  This trickle charger is intended to maintain the battery for long periods of time between power failures and is not intended for charging a fully discharged battery. If the battery is completely discharged, it must be removed and charged via a battery charger with higher current capability.   Figure  Block DiagramⅡ
                                                           TR-800 Service Manual  -16-Glossary Bi-directional Repeater: A repeater configuration in which the main and slave radios perform both receive and transmit functions. The audio and Rx Carrier signals from the receiver of the slave radio are routed to the transmitter of the main radio. Unlike the unidirectional case, though, the audio and Rx Carrier signals of the receiver of the main radio are also routed to the transmitter of the slave radio. Cross band repeater: A repeater in which the slave radio operates in a different frequency band than the main radio. Example: the slave radio operates on 162.075MHz in the high band VHF and the main radio operates on 452.025MHz in the 450-470MHz UHF band. Cross-band repeaters may be either unidirectional or bi-directional. Main Radio: The radio that performs the transmitting functions in the TR800 repeater station in the general unidirectional application. Relay Delay Time: The time duration the repeater remains in transmit mode after an active or valid signal is no longer detected. Repeater Knockdown: To deactivate a repeater or to remove it from service. Only the slave radio turns on at power up. Repeater Setup: To activate a repeater or to place it into service. Both radios turn on at power-up (repeater functional). Single band repeater: A repeater in which both the slave radio operates in a same frequency band. Example: receive at 455.075MHz and transmit at 460.075MHz in the 450-470MHz UHF band. Slave Radio: The radio that performs the receiving functions in the TR800 repeater station in the general unidirectional application. Unidirectional Repeater: A repeater configuration in which the slave radio receives signals only from the field radios and the main radio transmits signals only to the field radios.
                                                           TR-800 Service Manual  -17- MPU Pins Repeater front panel (MPU Model: uPD780114, CRYSTAL: 9.8304MHz) PIN No.  PIN NAME  I/O  DESCRIPTION 1 AVref  I Connect VDD 2 AVss  I To GND 3 IC(VPP)  I  To GND (programming pin)      short-circuit resistor added 4 VDD I +5V 5 Vss  I GND 6 X1  I Clock Input 7 X2  O Clock output 8  RESET I Knockdown 9  XT1  I  NC                               Connect VDD 10  XT2  I  NC                                    Open 11  SHIFT  O  Clock Frequency Shift                  Active: H 12  PTT/O  O  Main radio PTT signal output control     Active: L        13  RxD2  I  Analog serial data input (slave MPU communication) 14  TxD2  O  Analog serial data output (slave MPU communication) 15  RSW0(DN)  I  Encoder knob [DOWN] button input            High/low level   16  RSW1(UP)  I  Encoder knob [UP] button input   Rising Edge / Falling Edgeactive 17 LCDBL/LED0  O LCD backlight control/LED0          Active: H 18  LCDCS/LED1  O  LCD chip selection output/LED1   19  LCDSOD/LED2  I/O  LCD data reading/LED2           (LCD/LED I/O) 20  LCDDAT/LED3  O  LCD data output/LED3 21  LCDCLK/LED4  O  LCD clock output/LED4 22 EVss  I  GND 23 E VDD  I  Connect VDD (programming pin) 24 AFTest  O Audio test control 25  SpkSW  O  Main/slave speaker output control H: Main unit outputs        L: slave radio outputs 26  RXD1  I  Serial data input (main MPU communication)   27  TXD1  O  Serial data output (main MPU communication)   28  SETUP/O  O  Repeater setup output              Active: H 29  HOOK/RXD0  I  Palm microphone HOOK input/serial data input    Active: L 30  TXD0  O  Serial data output                  PTT active: L 31  RLED  O  Red LED                          Active: H 32  GLED  O  Green LED                        Active: H 33  PTT  I  Palm microphone PTT key input          PTT Active: L 34  OPT/O  O  OPT signal output                 Active: H
                                                           TR-800 Service Manual  -18-35  RPT/O  O  RPT signal output                 Active: H 36  KEYBL  O  Keypad backlight control             Active: H 37  Rx Tone/I  I  Slave radio signal input    Active: L    () 38  SETUP/I  I  SETUP signal input            On: H (rising edge trigger) 39  OPT/I  I  OPT key input           Active: L   () 40  RPT/I  I  RPT key input           Active: L     () 41  DN  I  DN key input            Active: L    () 42  UP  I  UP key input            Active: L     () 43  SCAN  I  SCAN key input         Active: L     () 44  MONI  I  MONI key input         Active: L    (external pull-up resistor connected)
                                                           TR-800 Service Manual  -19-  TR-800 Part List (Logic board) No.  P/N  Part Description  Ref. No.  Address  Qty. Remark1  3001060000000  Chip resistor 0603 0Ω J 1/10W  R0158  B3B  15          R0164 B2E          R0170 B4C          R0176 B4C          R0178 B4B          R0181 B4B          R0182 B4B          R0183 B4B          R0184 B4B          R0185 B3B          R0186 B3B          R0199 B2B          R1101 B4C          R1103 B3B          R1113 B4F    2  3001061020010  Chip resistor 0603 1KΩ J 1/10W  R0148  B3C  10          R0149 B3C          R0163 B3A          R0172 B3C          R0173 B3C          R0174 B3C          R0175 B3C          R0179 B4B          R0180 B4B          R0195 B1C    3  3001061030010  Chip resistor 0603 10KΩ J 1/10W  R0103 B2G 12         R0104 B3E          R0115 B3E          R0117 B3E          R0130 B3F          R0140 B3E          R0141 B3E          R0143 B2E          R0146 B1B          R0147 B1B          R0171 B3B
                                                           TR-800 Service Manual  -20-      R1121 B2D    4  3001061040010  Chip resistor 0603 100KΩ J 1/10W  R0118 B3F 4         R0145 B1B          R0198 B4E          R1106 B2D    5  3001061220000  Chip resistor 0603 1.2KΩ J 1/10W  R0125  B2E  1    6  3001061510000  Chip resistor 0603 150Ω J 1/10W  R0168  B2A  1    7  3001061520000  Chip resistor 0603 1.5KΩ J 1/10W  R0127  B3F  1    8  3001061540010  Chip resistor 0603 150KΩ D 1/10W  R1115 B2D 1   9  3001062230000  Chip resistor 0603 22KΩ J 1/10W  R0139  B2F  2          R0121 B3E    10  3001062240010  Chip resistor 0603 220KΩ J 1/10W  R0197  B4E  1    11  3001062720000  Chip resistor 0603 2.7KΩ J 1/10W  R0107  B3G  3          R0126 B3G          R0128 B3F    12  3001062730000  Chip resistor 0603 27KΩ D 1/10W  R0166  B3A  1    13  3001064710000  Chip resistor 0603 470Ω J 1/10W  R0129 B2F 1   14  3001064720000  Chip resistor 0603 4.7KΩ J 1/10W  R0105  B3E  7          R0124 B2D          R0142 B2E          R0159 B3B          R0177 B4C          R1114 B4C          R1118 B4B    15  3001064730000  Chip resistor 0603 47KΩ J 1/10W  R0101  B3G  25          R0102 B2G          R0106 B3G          R0108 B2E          R0109 B3G          R0110  B3G          R0111 B3G          R0112 B3F          R0150 B3C          R0151 B3C          R0152 B3C          R0153  B3C          R0154 B3C          R0155 B3C          R0156 B3E          R0160  B3B          R0161 B4E          R0162 B4E          R0187 B3B
                                                           TR-800 Service Manual  -21-      R0188 B3B          R0189 B3B          R0190 B3B          R1105  B3B          R1111 B4B          R1112 B3B    16  3001065620010  Chip resistor 0603 5.6KΩ J 1/10W  R0138  B2F  2          R0157  B2C    17  3001065630000  Chip resistor 0603 56KΩ J 1/10W  R1109  B2D  1    18  3001066800000  Chip resistor 0603 68Ω J 1/10W  R0167  B3A  1    19  3001066820000  Chip resistor 0603 6.8KΩ J 1/10W  R1104  B3B  1    20  3001066830000  Chip resistor 0603 68KΩ J 1/10W  R1110  B3D  1    21  3001162290000  Chip resistor 2010 2.2Ω J 1/2W  R0193  B4E  2        R0194 B4D    22  3001162700000  Chip resistor 2010 27Ω J 1/2W  R0165  B4A  1    23  3002994720010  Trimmer resistor 2.7*2.0*1.6 4.7KΩ ±25%    RV0104  B3A 1   24  3009161510000  Chip thick-film resistor 2010 150Ω F 3/4W  R0169  B4C  1    25  3101061010010  Chip capacitor 0603 100PF J 50V    C0163  B4F  5          C0164  B4F          C0165 B4F          C0168 B4F          C0171  B3F    26  3101062200010  Chip capacitor 0603 22PF J 50V  C0131  B2B  2          C0132 B2B    27  3101066800000  Chip capacitor 0603 68PF J 50V  C0133  B3B 1   28  3101071020010  Chip capacitor 0805 1000PF K 50V    C0150  B1C  12          C0151 B1B          C0152 B4D          C0154 B1C          C0155  B1C          C0156 B5E          C0157 B5E          C0162 B4F          C0166 B4F          C0169 B5F          C0170 B5F          C0175  B1C    29  3101071030010  Chip capacitor 0805 0.01UF K 25V  C0124  B2E  8          C0130 B2B          C0134 B3B          C0135  B4E          C0136 B4E          C0143 B2B
                                                           TR-800 Service Manual  -22-      C0149 B1B          C0161 B4E    30  3101073340000  Chip capacitor 0805 0.33UF K 16V  C0110  B2E 7         C0111 B3E          C0117 B2E          C0118 B2F          C0120  B3E          C0121 B2E          C0172 B2D    31  3101074710010  Chip capacitor 0805 470PF K 50V  C0103  B3E  14          C0112 B2E          C0123 B4E          C0126  B3A          C0129 B2B          C0137 B3A          C0138 B3A          C0139  B3B          C0140 B2A          C0142 B2B          C0144 B4B          C0145  B2D          C0146 B3D          C0148  B1B    32  3104081060070  Ta-capacitor 1206 10UF M 16V    C0102  B3E  5          C0104  B3E          C0105 B3E          C0147  B1C          C0160 B4F    33  3104081560020  Ta-capacitor 1206 15UF M 10V    C0127  B1B 2         C0128 B2A    34  3213212102010  Multi-layer inductor 1008 1uH    L0101  B4F 2         L0102 B4F    35  3221506601000  Chip ferrite bead 0603 600Ω±25% L0103 B2B 3       L0105 B2B        L0106  B4F    36   3301240700000  Schottky diode  MBD301  CR0101  B3G  1    37  3302030500020  Zener diode UDZSTE(1718B)18V    VR0108  B4F  1    38  3302240000040  Zener diode BZX84C5V1  VR0101  B2F 7       VR0102 B3E        VR0103  B2E        VR0104 B3G
                                                           TR-800 Service Manual  -23-    VR0105 B4E          VR0106  B2E          VR0107 B2F    39  3307110100090  LED KPT-1608CGCK Green  CR0107  T4F  6          CR0108 T3F          CR0111 T4F          CR0112 T2F          CR0113 T2D          CR0114  T3D    40  3399010600000  Switching Diode HSB123TR-E    D0112  B4B  8          D0113 B4B          D0114 B3B          D0115  B4B          D0116 B3B          D0117  B4B          D0118 B2B          D0119 B3B    41  3403002000000 Transistor 2SB1132L02T100R   Q0118  B4C  1    42  3403008000010 Transistor DTC114EE(TL)   Q0102  B3E 9         Q0105 B2E          Q0111 B2E          Q0114 B2D          Q0115  B3A          Q0117 B2A          Q0119  B3B          Q0120 B2D          Q0121 B3D    43  3410001000040 Transistor 2SA1641(S.T)   Q0113  B3A  1    44  3414001000020 Transistor MMBT3906  Q0101  B3G  2          Q0106 B3F    45  3414001000030  Darlington Transistor MMBTA13  Q0116  B2E  1    46  3414001000040 Transistor MMBT3904  Q0103  B3G  5          Q0107  B3G          Q0108 B3F          Q0123 B4C          Q0124  B5B    47  3503020000030 FET 2SK1824-T1-A   Q0112  B3B  1    48  3605008001690 Operational amplifier NJM2904M  U0102  B3E 2         U0105 B2F    49  3607037000000 Logic IC(NAND)-MC14011 U0103 B4E 2         U0107 B2E    50  3608002020890  Power management IC TA7805F(TE16L.F) 5V  U0108  B2A  1    51  3609018001090  IC BU4066BCFV Quad analog switch IC  U0104  B3E  1
                                                           TR-800 Service Manual  -24-52  3610003000000 SCM UPD78F0114HGB-8ES   U0110  B3B  1    53  3701098340020  Crystal 9.8304MHz NX8045GB  SMD   X01  B3B  1    54  4002000000070  Fuse 0466.200.NR 0.2A/125V  F0101  B5F 1   55  5202008100020  Chip socket 52746-0870 8pin  J0110  T3A  1    56  5202011100010  Chip socket B11B-ZR-SM3-TF(LF)    J0106  B1C  2        J0107  B5D    57  410R800100030  TR-800 Logic board PCB FR4 1.6T/2L/2P      1   58  3001063310010  Chip resistor 0603 330Ω J 1/10W    R0191  B2D 2         R0192 B3D    59   3303040400010  Switch diode BAS16  CR0103  B2F  1    60  3104081060080  Ta-capacitor 1206 10UF M 10V  C0141  B2B  1    61  3002995020000  Ceramic alloy potentiometer 5KΩ K CT-94EW  RV0101  B2D  2          RV0102 B3E    62  3002995030020  Ceramic alloy potentiometer 50KΩ K CT-94EW  RV0103  B2D 1    63  3101991050000  Polyester capacitor 4.5*13.5*10 1uF J 63V  C0101  B3G  1    64  3301200200000  Rectifier diode 1N4004 DO-41  CR0104  B3F  1    65  3307110600010  LED L-483GDT Green 2.5*5mm 2.2V  CR0105  T2A  1    66  3307110600020  LED L-483IDT Red 2.5*5mm 2.0V  CR0106  T2A  1    67  3307110600030  LED L-483YDT Yellow 2.5*5mm 2.1V  CR0102  T4A  1    68  3307110600050  LED L-483EDT Orange 2.5*5mm 2.0V  CR0119  T3A  1    69  3307990000080  LED LT5CB4-81-XA400714 super bright blue  CR0109  T2D  2          CR0110 T3D    70  3614037000000  3-Terminal voltage regulator IC MC78M09  U0109  B1B  1    71  4301060000010 Toggle switch SSGM1A0100  S01  B2G  1    72  4301080000040 Momentary contact switch (SPEA122200)  S02  T4A 1    73  4302030000040  Channel switch RH90N74AE20  K02  T4D  1    74  5110000000190  LCD Module JIC-MSBF-8943-06 (red backlight)    T3B 1    75  5202002100100  Pin socket 89400-0220 2pin  J0111  B1C  2       J0113 B4C   76  5202015200000  HDB15/F socket (DIP) 5512-15SA-01-BRJ-F1  J0102  B1E  3       J0103 B2C       J0104 B1D   77  5202040100030 Dual-row pins 40pin   J0113  B4E  0.1   78  5204008000000  RJ45 socket MODS-A-8P8C-H-S 8-line SHIELDED  J0109  B5G  1   79  7000037000000  Heat sink 15.3*17mm  U0109  B1B  1   80  7103008001010  Machine screw M3.0*8.0mm pan-head (Nickel-plating)    U0109  B1B  1   81  4308990000000  Low signal Relay G5V-1 9V DC  KR03  B5C  1   82  4308990000060  Low signal relay G5V-2-DPDT 12VDC 2A  KR00  B4C  1
                                                           TR-800 Service Manual  -25- TR-800 Part List 1 (Power Management Board) No.  P/N  Part Description  Ref. No.  Address  Qty. Remark1  3001061000000  Chip resistor 0603 10Ω J 1/10W  R2103  T2E  1   2  3001061020010  Chip resistor 0603 1KΩ J 1/10W  R0285 T2B 2       R2101 T2D   3  3001061030010  Chip resistor 0603 10KΩ J 1/10W  R0278  T2B  4      R0284 T2A        R0287 T3B       R2100 T2B   4  3001061040010  Chip resistor 0603 100KΩ J 1/10W  R0274  T1A  3       R0281 T2A       R0289 T3B   5  3001062720000  Chip resistor 0603 2.7KΩ J 1/10W  R0299  T3A  1   6  3001061530010  Chip resistor 0603 15KΩ J 1/10W  R0280 T1B 2       R0292 T2F   7  3001062220000  Chip resistor 0603 2.2KΩ J 1/10W  R0294  T2D  1   8  3001062230000  Chip resistor 0603 22KΩ J 1/10W  R0271  T1A  4       R0286 T2B       R0290 T3B       R0291  T3A    9  3001062430010  Chip resistor 0603 24KΩ J 1/10W  R0275  T1A  1   10  3001063330010  Chip resistor 0603 33KΩ J 1/10W RCT03333J  R0279  T1B 2       R0293  T2E    11  3001064710000  Chip resistor 0603 470Ω J 1/10W  R0267  T2F 2       R0268  T2E    12  3001064720000  Chip resistor 0603 4.7KΩ J 1/10W  R0272  T1A  7      R0273  T2A        R0282  T2A       R0288  T3B        R0295 T2D       R2102 T2D       R2104 T2E   13  3001066830000  Chip resistor 0603 68KΩ J 1/10W  R0296  T3E 1   14  3001069130000  Chip resistor 0603 91KΩ D 1/10W  R0297 T3E 1   15  3001081020000  Chip resistor 1206 1KΩ J 1/4W  R0270  T1B  1   16  3101071030010  Chip capacitor 0805 0.01UF K 25V  C0239  T3E  1   17  3101071040000  Chip capacitor 0805 0.1UF K 25V  C0226  T2B  3
                                                           TR-800 Service Manual  -26-    C0233 T2A       C0240 T2D   18  3101074710010  Chip capacitor 0805 470PF K 50V  C0227  T2B  8       C0228 T1B       C0229  T2B        C0231 T1A       C0235 T2A       C0236 T3A       C0237 T3A       C0238 T3A   19  3101081050020  Chip capacitor 1206 1UF K 25V    C0242  T2D  1   20  3414001000040  Transistor 300MHz 0.3V  Q0126  T2A 4     Q0218 T3B        Q0220 T2D         Q0224 T1A   21  3414001000020 Transistor PNP-SOT23-250MHz-0.3V  Q0217 T3B 2       Q0222 T1B   22  3605008001690 Operational amplifier NJM2904M DUAL U0205 T3B 2      U0206 T1A   23    Switch diode BAS16  CR0212  T3D  7    3303040400010   CR0213  T2F         CR0216 T2A     CR0217 T2B        CR0218 T3B        CR0220 T2B      CR221 T2B     24  3413001000000  Transistor UFMMT718 PNP SOT23  Q0223  T1B  1   25  3104082250030  Ta-capacitor 1206 2.2UF K 16V    C0234  T3B  1   26  3302240000050  Zener diode BZX84C27  VR0208  T3D  10       VR0209 T2E       VR0210 T1B     VR0211 T1A       VR0212 T2E         VR0213 T2A       VR0214 T2A       VR0215 T3F       VR0217 T1B   27  4011000000010  SMD fuse SMD 200F-2 15V 2A  F0202  T2B  1   28  410R800200100  TR-800 power supply board PCB FR4 1.6T/2L/4P      1   29  3302240000030 Zener diode-BZX84C7V5  VR0209  T2E  2       VR0218 T2A   30  3003991040010  Thermistor sensor 100KΩ ±1% NTC  Rth0201  B3D  1   31  3099990228000  Leaded resistor 0.22Ω J 2W  R0269  B3C  1
                                                           TR-800 Service Manual  -27-32  3103991060020  Electrolytic capacitor 4*7 10UF ±20% 25V  C0230  B2B  1   33  3103991070090  Electrolytic capacitor 6*12 100UF    ±20% 25V  C0225  B2D  2       C0232 B2D   34  3103992280020  Electrolytic capacitor 12.5*25 2200uF ±20% 25V  C0241  B2D 1   35  3103994770030  Electrolytic capacitor 2512 470UF 25V M 105  ℃ C0243 B3E 1  36  3216599224000  Bobbin inductor    0.35mm 220uH PI-DRU002-0031  L0201  B2E  1   37  3301160200000  Rectifier diode 1N5401D    CR0224  B3E  1   38  3301200200000  Rectifier diode 1N4004 DO-41  CR0214  B1B  2       CR0223 B1B   39  3301200200010  Rectifier diode 1N5821_rlg      CR0222  B2E  1   40  3301240400000 Three-terminal regulator diode TL431  U0209  B2D  1   41  3004116050000  Varistor 2512 6MΩ 0-0.05%/℃ CR0215 B1F 1  42  3416002000010 Transistor TIP42C PNP  Q0219  B1E  1   43  4002000000040  ATO Fuse clip 100057 15A  F0203  B2F  1   44  4210080000700  Speaker connection cable (2Pin plug) 2-core 80mm  Rth0201  B3D  1   45  4200250000000  TR-920 DC power cable#14 250mm  CN0201  B3D  1   46  4200250000100  TR-920DC power cable#14 250mm  CN0201  B3D  1   47  4200400000010  Connection cable 2PIN 450MM UL1007 #26  CR0219  B3A  1   48  4200400000200  Power cable L400MM 2PIN UL1015 #14  CN0202  B1D  1   49  4200250000200  Power cable L250MM 2PIN UL1015 #14  CN0203  B1D  1   50  4308990000010  Power relay G8P-1C4P-SPDT 12VDC 20A  KR01  B2C  1   51  5202002100100  Pin socket 89400-0220 2pin  Rth0201  B3D  1   52  5202002100000  Socket 3750S-02 2pin  CONN1  B3F  1   53  5202040100030  Dual-row pin 40pin    BAT LOW  B2B  0.05  54  5204002000000  DC power socket L150MM UL1015 #14  CN0204  B1F 1   55  7000037000000  Heat sink 15.3*17mm  Q0219  B1E  1   56  7103008001010  Machine screw M3.0*8.0mm Pan-head  Q0219  B1E  1
                                                           TR-800 Service Manual  -28-  Adjustment Description Logic Board Adjustment Test Apparatus 1.  20A/30V Power Supply                                     1set 2.  Ammeter                                                 1set 3.  Digital Voltmeter                                           1set 4.  Test Jumper Cables (mating with test ports of TR-800 and the communication test set) 5.  Communication System Analyzer (such as HP8921 series)            1set  Adjustment Radio Configuration Use HR-800E to program the TR-800. Table  Ⅰ and table Ⅱ  illustrate the factory default settings in a general operation mode. The “Ignition Sense Time” of main radio defines time delay from SETUP to KNOCKDOWN.  Table  Radio Programming PresetⅠ Item  Main Radio  Slave Radio AUX3 I/O  Ext. PTT  Ext. PTT AUX4 I/O  Rx Carrier(Tone)  Rx Carrier(Tone) AUX5 I/O  Rx Tone(Carrier)  Rx Tone(Carrier) Horn Alert Logic  NA  1s Ignition Sense  0h0m  NA Drop Out Delay  3s Scan Gap Time  400ms Repeater Hang Time  2s  Table   Logic Board Switch ConfigurationⅡ: Toggle Switch  S01-1 S01-2 S01-3 S01-4 S01-5 S01-6 S01-7 S01-8 S01-9  S01-10 Factory Default  ON OFF OFF ON ON ON ON ON OFF  ON  Test Procedure a)  Base Station Mode Make sure the TR-800 is in SETUP state and deactivate RPT & OPT functions. The TR-800 operates on base station mode with main radio to transmit and slave radio to receive (similar to a mobile radio). Correctly cable the test ports to communication system analyzer before adjustment. Measure Adjustment Item Condition Instrument Point Point Method  Specification/Remark Slave radio receive Channels with/without Communication test set  J0109 K02 Rotate the knob to adjust the volume Squelch open sensitivity:  -118±3dBm
                                                           TR-800 Service Manual  -29-tones  to rated power, check receiver’s squelch open/off sensitivity, with signaling squelch open sensitivity, audio distortion & Rx S/N Squelch off sensitivity:  -118±3dBm CCTSS squelch sensitivity:  -118±3dBm CDCSS squelch sensitivity:  -118±3dBm Audio distortion: ≤3%@3W ≤10%@5WRx S/N: ≥45dB (wide) ≥40dB (narrow) Main radio transmit Any channel without tones Communication test set Main radio Tx connector/ Adjust the MIC audio output amplitude of Analyzer to 6-10mVinto J0109 3pin; check Tx frequency deviation matching 60% system Dev.; check modulation distortion and Tx S/N  Tx frequency deviation:  3.0±0.2kHz (wide)      1.5±0.1kHz (narrow) Modulation distortion: ≤3% Tx S/N: ≥45dB (wide)   ≥40dB (narrow) b)  Uni-directional Repeater Mode (Forward) Make sure the TR-800 is in SETUP state and activate RPT function. The TR-800 operates on uni-directional repeater mode with slave radio keys main radio to repeat transmission (forward direction). Correctly cable the test ports to communication system analyzer before adjustment. Measure Adjustment Item Condition Instrument Point Point  Method  Specification/Remark MONI  Any channel  / / MONI Check up Long press monitor key, the slave radio processes monitoring, with green LED flashes Uni-directional repeater (forward) Channels with/ without tones Communication test set Main radio Tx connectorRV0101Adjust the signal output amplitude of Analyzer to -47dBm, adjust RV0101 to obtain a 60% system deviation; check the modulation distortion and RX S/N; decrease the signal output Duplex sensitivity:  -116(+1/-3dBm) CTCSS sensitivity: -116(+1/-3dBm) CDCSS sensitivity: -116(+1/-3dBm) Repeater frequency deviation: 2.9±0.2kHz (wide) 1.4±0.1kHz (narrow) Repeater audio distortion:  ≤3%@3W
                                                           TR-800 Service Manual  -30-amplitude of the analyzer, check the duplex sensitivity.   ≤10%@5W Tx S/N: ≥42dB (wise) ≥37dB (narrow) Max. Power output (without duplexer): 45±2W(UHF) 50±2W(VHF) Rx audio output Any channel without tones Communication test set  J0103 / Check the audio output amplitude of 5 pin on the accessory connector Audio output:  ≥200mV Repeater Hang Time Any channel Communication test set  / / In the repeater setup state, terminate the signal output of the analyzer, check the repeater hang time.   Repeater hang time: 2S Linked audio relay Any channel without tones Communication test set Main radio Tx connectorRV0103Adjust the audio output amplitude of the analyzer MIC to 120mVinto 3 pin of J0103; adjust RV0103 to obtain a 60% system deviation, check modulation distortion and TX S/N Tx frequency deviation: 3.0±0.2kHz (wide) 1.5±0.1kHz (narrow) Modulation distortion: ≤3% Tx S/N: ≥45dB (wide) ≥40dB (narrow) Repeater Scan Any channel Signal generation or radio  / / Set SCAN key active Use signal generator or portable transmitter to test whether repeater scanning works correctly and processes retransmission, and repeat testing on other channels.    c)  Uni-directional Repeater Mode (reverse) Make sure the TR-800 is in SETUP state and activate OPT function. The TR-800 operates on uni-directional repeater mode with slave radio keys main radio to repeat transmission (backward direction). Correctly cable the test ports to communication system analyzer before adjustment. Measure Adjustment Item Condition Instrument Point Point  Method  Specification/Remark
                                                           TR-800 Service Manual  -31-MONI  Any channel  / / MONI Check up Long press the monitor key, the main radio processes monitoring, with red LED flashes. Slave radio transmit Any channel without tones Communication test set Slave radio Rx connector/ Adjust the audio output amplitude of the analyzer MIC to 7mVinto 3 pin of J0109, check the TX frequency dev. Matching of 60% system Dev., check modulation distortion and TX S/N.  duplex frequency deviation:   3.0±0.2kHz (wide) 1.5±0.1kHz (narrow) Modulation distortion: ≤3% Tx S/N: ≥ 45dB (wide) ≥40dB (narrow) Uni-directional repeater (reverse) Channels with/ without tones Communication test set Slave radio Rx connectorRV0102Adjust the signal output amplitude of Analyzer to -47dBm, adjust RV0102 to obtain a frequency dev. of 60%; check the modulation distortion and TX S/N; decrease the signal output amplitude, check the duplex sensitivity.  Duplex sensitivity:  -117(+1/-3dBm) CTCSS duplex sensitivity:  -117(+1/-3dBm) CDCSS duplex sensitivity: -117(+1/-3dBm) Repeater frequency deviation: 2.9±0.2kHz (wide) 1.4±0.1kHz (narrow) Repeater audio distortion: ≤3%@3W ≤10%@5W Tx S/N: ≥42dB (wide) ≥37dB (narrow) Max. Power output (without duplexer): 45±2W(UHF) 50±2W(VHF)  d) Radio Kill Function Measure Adjustment Item Condition Instrument Point Point Method  Specification/Remark Remote Knockdown Channel with optional signaling Radio  /  /  Set S01-2 “ON” Transmit DTMF code via the portable radio to remotely disable the main radio, orange LED goes out and the TR-800 is in knockdown state   e) Knockdown State
                                                           TR-800 Service Manual  -32-Measure Adjustment Item Condition Instrument Point Point  Method  Specification/Remark Knockdown state Any channel with SETUP disabled Handheld microphone or test cable / MONI, SCAN pushbutton / Short or long press of the monitor and scan button is disabled; unable to transmit with palm microphone or test cable connected, only receives (i.e. only slave radio works and receive only)  f) Provisory Settings At the end of the test, set S01-2, S01-3, S01-9 to “OFF” to prohibit users the access to the D.B.D feature, only your dealer or skilled technicians are authorized to enable this feature upon the requirement of users.
                                                           TR-800 Service Manual  -33-Power Management Board Adjustment Test Apparatus 1、 20A/30V Power Supply                                     1set 2、 Analog ammeter                                           1set 3、 Digital Voltmeter                                           1set 4、 12V lead acid battery (not fully charged)                      1set  Circuit detect and temperature-control test Connect CN0201 (To Power Supply) and CN0204 (To Ext. Battery) with DC power output 13.8V respectively. Measure Adjustment Item Condition Instrument Point Point  Method  Specification/Remark AC to DC over-voltage detect /  Digital voltmeter  CR0219 CN0201Increase or decrease the input voltage  Gradually increase the voltage of CN0201 to 16.4V, the protection circuit  will drive KR01  to  revert to DC power supply. Decrease the voltage of CN0201 to 13.4V and return to AC power supply.   AC mains fail detect  / / CR0219 CN0201Close or open input voltage  Remove the voltage of CN0201, driving KR01  to revert to DC power supply with CR0219 illuminates; Apply voltage to CN0201, and KR01 is activated, then return to AC power supply with CR0219 goes out.   Battery low detect Close CN0201 voltage Digital voltmeter CR0219,BAT LOW CN0204Raise or lower input voltage Gradually decrease the voltage of CN0204 to 10.2V, driving KR01 to cut down DC power supply, with CR0219 goes out, “BAT LOW”provides a low; Apply voltage to CN0201, with CR0219 flashes briefly, then return to AC power supply; remove the voltage of CN0201, gradually increase the voltage of CN0204 to 12V, the KR01 is activated to toggle to DC power supply with CR0219 illuminates.  Thermal controlled fan Soldering iron or hot air gun Digital voltmeter  Fan Rth0201 Heating or cooling Heat the Rth0201 with soldering iron or hot air gun, check the voltage of fan increases (6.0V~11.5V) with the air  flow increases.
                                                           TR-800 Service Manual  -34- Floating charge test Connect CN0204 to 12V battery; CN0201 remains connected with 13.8V power supply. Measure Adjustment Item Condition Instrument Point  Point  Method  Specification/Remark Floating charge  /  Analog Ammeter  CN0204 / Check Check the charging current is about 400mA, and will drop to 10-25mA when fully charged.
                                                           TR-800 Service Manual  -35- Duplexer Instructions Electrically a duplexer is a device using sharply tuned resonate circuits to isolate a transmitter from a receiver. This allows both of them to operate on the same antenna at the same time without the transmitter RF frying the receiver. Before using your repeater, you must tune the duplexer using one of the following three methods for ensuring that the duplexer is tuned to the correct frequencies of operation:  Pre-Tuned Method (preferred method) Order the duplexer from the manufacturer or supplier pre-tuned to the desired frequencies. This is not a “method” of tuning the duplexer but does not require any field tuning or test equipment. Note that there must be a separation of the transmit and receive frequencies. This is called “split”. On two meters the split is about 600 KHz. On 70cm the split is much easier to do 5MHz.  Visual Method Use a tracking (sweep) generator and spectrum analyzer to adjust the tuning of the pass bands and reject bands of the duplexer.  Emergency Method The following paragraphs address a simple method of tuning a “notched” duplexer such as DT04 UHF duplexer. This is not as accurate a method of tuning as the visual method afforded by the tracking generator /spectrum analyzer sweep setup but it is much less costly. It may be sufficiently good for all but the most exacting applications. Use this method only when the operating frequencies of the main radio and slave radio meet the requirements of the duplexer. The duplexer you can order from HYT is notched type (band-reject) only and the minimum separation available is 4MHz on UHF band and 3.5MHz on VHF band. Note that this notched type duplexer offers a considerably narrow bandwidth. If the operating transmitter/receiver frequencies for the TR-800 are appreciably different than that of duplexer specification, degraded performance of the repeater will result. The following procedure assumes that the duplexer is applied and the radios should be connected to the proper ports of the duplexer with the RF coaxial cables provided in the TR-800 kit. The duplexer should not be mounted on the bracket and the tuning screws of the duplexer (on the other side of the cavities, opposite to the RF connectors) should be accessible. Programming the Radios 1.  Program the main radio with an additional “receive only” mode at the frequency of receive (assume that the main radio operates as transmitter of a uni-directional repeater). 2.  Program the slave radio with an additional “receive only” mode at the frequency of transmit (assume that the slave radio operates as receiver of a uni-directional repeater). 3.  Connect a communications test set, such as HP8921 series, or an RF signal generator to the antenna port of the duplexer. The test set should be operating in the “Generate” mode. Modulate the RF source with a 1kHz tone at 60% system deviation to facilitate “hearing” the signal during the tune-up procedure. Tuning the Main Radio Section Tuning the main radio section of the duplexer begins with the tuning screw closest to the antenna port of the duplexer.
                                                           TR-800 Service Manual  -36-1.  Adjust the frequency of the communication test set or generator to that of receive. 2.  Place the main radio on the receive frequency mode defined in Step 1 under “Programming the Radios”. 3.  Adjust the level of the communication test set or generator until the main radio emits a weak signal. 4.  Increase the level of the communication test set or generator by approximately 20dB. 5.  Adjust the tuning screw of the duplexer for the greatest rejection of the signal. This will appear as a noisier signal. If necessary: 5A. Slightly loosen the locking nuts of the tuning screws to allow the tuning screws to turn more freely (but not “sloppy”) and 5B. Increase the level of the communication test set or generator to maintain an audible 1kHz tone. 6.  Repeat steps Step 4, Step 5, Step 5A and Step 5B for each of the tuning screws on the duplexer. Begin with the tuning screw closest to the antenna port and move in order toward the tuning screw closest to the main radio port. 7.  Tighten the locking nuts of the tuning screws. To avoid damage to the tuning screws and to allow fine tuning of the duplexer, do not over tighten the locking nuts.   8.      Repeat Step 5, Step 5A and Step 5B to fine-tune the main radio section of the duplexer. Tuning the Slave Radio Section Tuning the slave radio section of the duplexer begins with the tuning screw closest to the antenna port of the duplexer. 9.    Adjust the frequency of the communication test set or generator to that of transmit. 10. Place the slave radio on the receive frequency mode defined in Step 2 under “Programming the Radios”. 11. Adjust the level of the communication test set or generator until the slave radio emits a weak signal. 12. Increase the level of the communication test set or generator by approximately 20dB. 13. Adjust the tuning screw of the duplexer for the greatest rejection of the signal. This will appear as a noisier signal. If necessary: 13A. Slightly loosen the locking nuts of the tuning screws to allow the tuning screws to turn more freely (but not “sloppy”) and 13B. Increase the level of the communication test set or generator to maintain an audible 1kHz tone. 14. Repeat steps Step 12, Step 13, Step 13A and Step 13B for each of the tuning screws on the duplexer. Begin with the tuning screw closest to the antenna port and move in order toward the tuning screw closest to the slave radio port. 15. Tighten the locking nuts of the tuning screws. To avoid damage to the tuning screws and to allow fine tuning of the duplexer, do not over tighten the locking nuts. 16. Repeat Step 13, Step 13A and Step 13B to fine-tune the slave radio section of the duplexer.
                                                           TR-800 Service Manual  -37- Disassembly and Installation Removing and Installing the Top Cover 1.  using a screwdriver to Remove the seven screws (M3.0X6.0)   that locking the top cover of ①repeater, shown as Figure 1. 2.  Remove the top cover  , shown as Figure 1.② 3.    Install the top cover as reverse steps.                                                   Figure 1  Removing and Installing the Front Panel 1.  Press the 6 latches that locking the front panel to the    housing to separate and remove them from the housing  , s①hown as Figure 2. 2.  Remove the front panel   shown as Figure 2, and pull out the two ②set of jumper wires, two repeater cables, accessory connector cable, and connecting cable of the DC power indication LED. 3.  Install the front panel as reverse steps.                Figure 2 2111111121111
                                                           TR-800 Service Manual  -38-Removing and Installing the Control Panel 1.  Remove the Volume Control knob ① shown as Figure 3. 2.  Remove the nut   using a special spanner, shown as Figure 3. ② 3.  Remove the six screws (ST3.0X8.0)   that secure the control panel using a screwdriver, sho③wn as Figure 4. 4.  Gently press and remove the RJ45 port   from the front panel, then pull out the speaker cable to ④remove the controller PCB, shown as Figure 4.   5.  Install the control panel as reverse steps.                                      Figure 3                                            Figure 4  Removing and Installing the Rear    Plate 1.  Pull out the ATO fuse  , shown as Figure 5.① 2.  Press the spring latch   located on the two ②edges of the DC socket, and push the DC socket into the housing to separate the socket from the rear plate , shown as Figure 5.③ 3.  Remove the seven screws (M3.0X6.0)   that secure the rear ④plate using a screwdriver, shown as Figure 5. 4.  Remove the two RF cables of both radios, and connecting cable of the fan, then remove the 3 power jumper cables that connecting AC socket with switch power, using a screwdriver, and that’s all for you to get prepared to remove the rear    plate. 5.  Installing the rear plate as the reverse steps.           2143333334443222214444
                                                           TR-800 Service Manual  -39-                                   Figure 5  Removing and Installing the Radio 1.  Remove the screw (M4.0X6.0)   that secure the ①thermistor sensor using a screwdriver, shown as Figure 6. 2.  Remove the eight screws (M3.0X6.0)   that secure the bracket of radio using a screwdriver, shown ②as Figure 6.   3.  Remove the bracket ③ shown as Figure 6, and remove the 2 signal cables and 2 power cables of both radios. 4.  Remove the eight screws (M4.0X6.0)   that secure both radios using a screwdriver, and then ④remove both radios  , shown as Figure 7.⑤ 5.  Install both radios as the reverse steps.                                        Figure 6                                             Figure 7  Removing and Installing Housing 1.  Remove the six screws (M3.0X6.0) that secure the housing using a screwdriver, to remove the housing ①, shown as Figure 8.   2.  Install the housing as the reverse steps.        3122222222544444444
                                                           TR-800 Service Manual  -40-                                               Figure 8  Removing and Installing Switch Power 1.  Remove the four screws (M4.0X6.0) that secure the switch power using a screwdriver, to remove the switch power ①, shown as Figure 9. 2.  Install the switch power as the reverse steps.                                            Figure 9  Removing and Installing the Power Management PCB 1.  Remove the four screws (M3.0X6.0) that secure the power    management PCB using a screwdriver, to remove the power    management PCB ①, shown as Figure 10. 2.  Install the power    management PCB as the reverse steps.                                            Figure 10 111111111111
                                                           TR-800 Service Manual  -41- Exploded View                                   ABBBCCCDDDDEEEEFFFFFFFFFFFFFFFFFFFFFFFFGGGGGGBBBBHHHHHHHHHHHIIIIIJJJJCCCCCC12345678910 11 12 13 14 15 16 17 181921222324252627 28 29 30313233343536373839404142434445464748495053545556575960616263646551525820

Navigation menu