Haier AW09EH2VHA User Manual AIR HANDLER (INDOOR BLOWER&EVAP) Manuals And Guides 1802066L
User Manual: Haier AW09EH2VHA AW09EH2VHA HAIER AIR HANDLER (INDOOR BLOWER&EVAP) - Manuals and Guides View the owners manual for your HAIER AIR HANDLER (INDOOR BLOWER&EVAP) #AW09EH2VHA. Home:HAIER:/ Air Handler Parts:HAIER air handler parts:#AW09EH2VHA HAIER air handler parts:#AW09EH2VHA HAIER air handler (indoor blower&evap) manual
Open the PDF directly: View PDF 
.
Page Count: 10
| Download | |
| Open PDF In Browser | View PDF |
Ductless Split Air Conditioner Installation Manual Indoor AW09EH2VHA AW12EH2VHA AW18EH2VHA Outdoor 1U09EH2VHA 1U12EH2VHA 1U18EH2VHA Table of Contents Step 1 - Preparation ...................................................................................................................... 2 Step 2 - Installation of the Indoor Unit ........................................................................................... 3 Step 3 - Installation of the Outdoor Unit ........................................................................................ 4 Step 4 - Interconnecting the Indoor and Outdoor Units ................................................................. 5 Step 5 - Leak Test and Evacuation.................................................................................................. 6 Step 6 - Charging........................................................................................................................... 7 Section 7 - Explaining Operation to the End User........................................................................... 8 .................................................................................................. 8 Section 9 - Seacoast Application ................................................................................................... 8 0010586954 ENGLISH Step 1 - Preparation • • • • • • • • • • • • • • • • • • • • • • Required Tools for Installation Procedure for Selecting the Location Drill Wire Snipper Hole Saw 2 3/4” Vacuum pump Soap-and-water solution or gas leakage detector Torque wrench 17mm, 22mm, 26mm Tubing cutter Flaring tool Razor knife Measuring tape Level Micron gauge Nitrogen Mini-Split AD-87 Adapter (1/4” to 5/16”) A - Non-adhesive Tape B - Adhesive Tape C - Saddle (L.S.) with screws D - Electrical wiring E - Drain hose (Included) F - Insulation G - Piping hole cover (Included) • Choose a place solid enough to bear the weight and vibration of the unit and where the operation noise will not be amplified. • Choose a location where the hot air discharged from the unit or the operation noise and will not cause a nuisance to the neighbors of the user. • There must be sufficient space for carrying the unit into and out of the site. • There must be sufficient space for air passage and no obstructions around the air inlet and air outlet. • The site must be free from the possibility of flammable gas leakage in a nearby place. • Locate the unit to avoid noise and discharged hot air will not annoy the neighbors. • Install units, power cords and inter-unit cables at least 10ft away from television and radio sets. This is to prevent interference to images and sounds. (Noise may be heard even if they are more than 10ft away depending on radio wave conditions.) • Since drain flows out of the outdoor unit, do not place anything under the unit that must be kept away from moisture. Note: 1) Cannot be installed hanging from ceiling or stacked. 2) If installing on a high place such as a roof, with a fence or guard rail around it. 3) If there is a potential for accumulated snow to block the air inlet or heat exchanger, install the unit on a higher base. 4) R-410A refrigerant is a safe, nontoxic and nonflammable refrigerant. However, if there is a concern about a dangerous level of refrigerant concentration in the case of refrigerant leakage, add extra ventilation. 5) Avoid installing the outdoor unit where corrosive gases, such as sulfur oxides, ammonia, and sulfurous gas, are produced. If unavoidable, consult with an installation specialist about using a corrosion-proof or anti-rust additive to protect the unit coils. Clearances of Indoor and Outdoor Units This picture is for reference only. Your product may look different. Read this manual before installation. Explain the operation of the unit to the user according to this manual. The models adopt HFC free refrigerant R410A Attention must be paid to the pitch of drain hose more than 2in. more than 4in. G Floor xing dimensions of the outdoor unit (Unit: inch) Arrangement of piping directions more than 4in. F Rear left Z A Rear right Left 1 2 Right C Below Dimensions(inches) Model 1 more than 4in. more than 4in. The marks from A to G in the gure are the name of the parts. The distance between the indoor unit and the oor should be more than 6 feet. 1U09/12EH2VHA 4 1/2” 23 1/4” 4 1/2 1U18EH2VHA 5 1/16” 26” 5 1/16” Fixing of outdoor unit D Fix the unit to concrete or block with bolts (10mm) securely. E more than 24in. When tting the unit to wall surface, roof or rooftop, x the unit securely in consideration of earthquake and strong wind. If vibration may affect the house, x the unit by attaching a vibration-proof mat. more than 6in. PAGE 2 x2 INSTALLATION 12 3/4” 15 3/4” Step 2 - Installation of the Indoor Unit Attaching the Mounting Plate to the Wall ENGLISH 2.1 Step 2.1 Using a stud sensor, locate and mark the stud positions in the wall where the indoor unit is to be mounted. 2.2 Step 2.2 Place the mounting plate on the wall in the desired location taking into account the minimum clearances necessary for proper operation. Step 2.1 Step 2.2 Step 2.3 Step 2.4 Step 2.5A Step 2.5B Step 2.6 Step 2.7 Step 2.8A Step 2.8B Using a level, verify the mounting plate is horizontal and mark the screw locations. 2.3 Step 2.3 Screw the mounting plate to the wall. The piping for the indoor unit may be routed to the unit from one of several directions. Left, Left Rear, Right, Right Rear, or Below (Illustration 1). 2.4 Step 2.4 Knockouts are provided on the case for Left, Right, and Right Below. Drilling the hole through the wall for left rear or right rear installation 2.5 Step 2.5A & 2.5B Measure and mark the location where the piping hole is to be drilled. 2.6 Step 2.6 Drill the piping hole using a hole saw of the correct diameter. Angle the drill with a downward pitch to the outside wall so that the outside hole will be ¼” lower than the inside hole, giving the hole the proper angle for condensate drainage. 2.7 Step 2.7 Install the piping hole cover flange at the hole opening on the inside wall. NOTE: The cover flange may require modification to fit properly behind the wall unit housing. 2.8 Step 2.8A & 2.8B Bundle the refrigerant piping, drain piping and wiring with tape and pass the bundle through the piping hole. NOTE: When bundling the power cable, leave sufficient length available in the indoor unit to make the connections to the terminal block. Piping Exit Options Rear left Rear right Left Right Below Illustration 1 INSTALLATION PAGE 3 Mounting the Indoor Unit Onto the Wall Plate ENGLISH 2.9 Step 2.9 With the top of the indoor unit closer to the wall, hang the indoor unit on the upper hooks of the mounting plate. Slide the unit slightly side to side to verify proper placement of the indoor unit on the mounting plate. Rotate the lower portion of the indoor unit to the mounting plate, and lower the unit onto the lower hooks of the mounting plate. (Illustration 2) Verify the unit is secure. 2.10 Step 2.10 Step 2.9 Step - 2.10 Slightly raise the entire unit vertically, pull the lower portion of the unit off the lower hooks of the mounting plate and away from the wall, then lift the upper portion of the unit off the upper hooks of the wall plate. mounting plate Illustration 2 Electrical Connections for the Indoor Unit 2.11 Step - 2.11A & 2.11B To make the electrical connections for the indoor unit, two cover plates must be removed. Raise the front cover to access the screws to remove these covers. 2.13 Step 2.11A Step 2.11B Step 2.12 Step 2.13A Step - 2.13 Access the four conductor cable through the cover plate opening and make the wiring connections noting the wire color used on each terminal. The color of each wire must match the same positions on the terminal block of the outdoor unit. (Illustration 3) Failure to wire the system correctly may lead to improper operation or component damage. 1(N) 2 (L) 3 (C) 2.14 Outdoor unit Indoor unit Step - 2.14A & 2.14B After the terminal block wiring is completed, replace both cover plates. 3wire 1 4AWG Control Wiring Step 2.13B Outdoor unit 1(N) 2 (L) 3 (C) Step 3 - Installation of the Outdoor Unit Illustration 3 Indoor unit 3wire 1 4AWG Attaching Drain Elbow to Outdoor Unit Control Wiring Power Wiring Step - 3.1 If attaching the supplied drain elbow to the outdoor unit, do so prior to attaching the refrigerant lines and wiring. Extension piping to attach to this fitting is field supplied. Electrical Connections for the Outdoor Unit 3.2 Step - 3.2 Remove the cover plate of the outdoor unit to expose the terminal block connections. PAGE 4 INSTALLATION Step 3.1 Step 3.2 1(N ) 2 (L) (Heat Pump models only) 3.1 1(N ) 2 (L) 3 (C ) Power Wiring 3.3 Step - 3.3 3.4 Step 3.3 ENGLISH Connect the wiring for both the power source and indoor wiring. Wire the system according to applicable national / local codes. Verify that the wiring connections for the indoor unit match wire for wire. (1-1, 2-2, 3-3, Gnd-Gnd). Failure to wire the system correctly may lead to improper operation or component damage. Step 3.4 Step - 3.4 Replace the cover plate. Step 4 - Interconnecting the Indoor and Outdoor Units *See Steps 2.11 - 2.13 & 3.2 - 3.4 for connecting the electrical. CAUTION Outdoor unit Piping 4.1 B A The standard lineset length is 25ft. If the installation length is oz /ft. for the 9K, 12K, 18K. (Illustration 4) Cut the lineset to outdoor unit valves. to chart. Indoor unit B A Indoor unit Outdoor unit ● Outdoor unit to the B ● Oil trap Indoor unit A ● Max. Elevation: A Max = 50ft/15m(9k/12k) = 50ft/15m(18k) In case the height of A is more than 15ft / 5m, an oil trap should be installed every 16-23ft /5-7m Max. Length: B Max = 66ft/20m(9k/12k) = 83ft/25m(18k) Illustration 4 Step - 4.1 Refrigerant piping connections for the mini-split system are made utilizing flare connections. Follow standard practices for creating pipe flares. When cutting and reaming the tubing, use caution to prevent dirt or debris from entering the tubing. Remember to place the nut on the pipe before creating the flare. 4.2 Step - 4.2 Step 4.1 To join the lineset piping together, directly align the piping flare to the fitting on the other pipe, then slide the nut onto the fitting and tighten. Misalignment may result in a leaking connection. 2.17 Step - 4.3 Half union Flare nut Step 4.2 Forced fastening without careful centering may damage the threads and cause a leakage of gas. Pipe Diameter(ǿ) Fastening torque Liquid side6.35mm(1/4") 18N.m/13.3Ft.lbs Liquid/Gas side9.52mm(3/8") 42 N.m/30.1Ft.lbs Spanner Torque wrench Two wrenches are required to join the flare connections, one standard wrench, and one torque wrench. See Table 1 for the specific torque per piping diameter. Gas side 12.7mm(1/2") 55N.m/40.6Ft.lbs Gas side 15.88mm(5/8") 60 N.m/44.3Ft.lbs Table 1 Step 4.3 INSTALLATION PAGE 5 Step 5 - Leak Test and Evacuation ENGLISH Leak Test Hazard of Explosion! Never use an open flame to detect gas leaks. Explosive conditions may occur. Use a leak test solution or other approved methods for leak testing. Failure to follow recommended safe leak test procedures could result In death or serious injury or equipment or property damage. Use only dry nitrogen with a pressure regulator for pressurizing unit. Do not use acetylene, oxygen or compressed air or mixtures containing them for pressure testing. Do not use mixtures of a hydrogen containing refrigerant and air above atmospheric pressure for pressure testing as they may become flammable and could result in an explosion. Refrigerant, when used as a trace gas should only be mixed with dry nitrogen for pressurizing units. Failure to follow these recommendations could result in death or serious injury or equipment or property damage. 5.1 Step - 5.1 Step 5.1 Step 5.2 Step 5.3 Step 5.4A Step 5.4B Step 5.5A Step 5.5B Step 5.6 Using a tank of nitrogen with attached regulator, charge the system with 150 PSIG of dry nitrogen. Use adapter AD-87 (field supplied) to connect to the valve. Check for leaks at the flare fittings using soap bubbles or other detection methods. If a leak is detected, repair and recheck. If no leaks are detected, proceed to evacuate the system. System Evacuation 5.2 Step - 5.2 Attach a manifold gauge, micron gauge, and vacuum pump to the suction line port using adapter AD-87 (field supplied). (Illustration 5) Evacuate the system to 350 microns. Close the vacuum pump valve and check the micron gauge. If the gauge rises above 500 microns in 60 seconds, evacuation is incomplete or there is a leak in the system. If the gauge does not rise above 500 microns in 60 seconds, evacuation is complete. 5.3 Step - 5.3 Remove the adapter and hose connection from the suction line port, and replace the cap. 5.4 Step - 5.4A & 5.4B Remove the cap from the liquid line valve. Using the hex wrench, open the valve, then replace and tighten the cap. 5.5 Step - 5.5A & 5.5B Remove the cap from the suction line valve. Using the hex wrench, open the valve, then replace and tighten the cap. 5.6 Step - 5.6 Wrap the lineset, drain line, and wiring starting at the bottom of the bundle with an overlap type wrap, concluding at the PAGE 6 INSTALLATION Illustration 5 piping hole. Use a sealant to seal the piping hole opening to prevent weather elements from entering the building. (Illustration 6) It becomes The end is imm- It waves. The gap with the There is the bad high midway. ersed in water. ground is too small smell from a sewer Illustration 6 Step 6 - Charging See Steps 5.2 - 5.5 for evacuating the system prior to charging. The standard lineset length is 25ft. If the installation length is different, adjust the refrigerant charge by .2 oz / ft. for the 9K, 12K, 18K, and 24K model. (Step 4 - Illustration 4) This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Do not vent into the atmosphere. Refrigerant type: R410A GWP* value: 1975 GWP = global warming potential Please fill in with indelible ink, • 1 the factory refrigerant charge of the product • 2 the additional refrigerant amount charged in the field and • 1+2 the total refrigerant charge on the refrigerant charge label supplied with the product. The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the stop valve cover). A - contains fluorinated greenhouse gases covered by the Kyoto Protocol B - factory refrigerant charge of the product: see unit name plate C - additional refrigerant amount charged in the field D - total refrigerant charge E - outdoor unit F - refrigerant cylinder and manifold for charging R410A 1= oz 2 2= oz 1+2= oz 1 F Please kindly explain to our customers how to operate through the instruction manual. Check Items for Test Run Refrigerant Charge Label Contains fluorinated greenhouse gases covered by the Kyoto Protocol System Test Put check mark √ in boxes No gas leak from linesets? Are the linesets insulated properly? Are the connecting wirings of indoor and outdoor firmly inserted to the terminal block? Is the connecting wiring of indoor and outdoor firmly fixed? Is condensate draining correctly? Is the ground wire securely connected? Is the indoor unit securely fixed? Is power source voltage correct according to local code? Is there any noise? Is the lamp normally lighting? Are cooling and heating (when in heat pump) performing normally? Is the operation of room temperature sensor normal? A B C D E INSTALLATION PAGE 7 ENGLISH Verify the condensate drain line has a constant pitch downward for proper water flow. There should be no kinks or rises in the tubing which may cause a trapping effect resulting in the failure of the condensate to exit the piping. Less than 5cm Section 7 - Explaining Operation to the End User ENGLISH • Using the OPERATING INSTRUCTIONS, explain to the user how to use the air conditioner (the remote controller, removing for operation, etc.) • Recommend that the user read the OPERATING INSTRUCTIONS carefully. Model Name Operating Range Power Supply Electrical Data Refrigerate Line System Outdoor Indoor Cooling °F(°C) Heating °F(°C) Voltage, Cycle, Phase V/Hz/Compressor Type Maximum Fuse Size A Minimum Circuit Amp A Connections Liquid O.D. in Suction O.D. in Factory Charge Oz Maximum Line Length Ft / m Maximum Height Ft / m 09EH 12EH 18EH 1U09EH2VHA 1U12EH2VHA 1U18EH2VHA AW09EH2VHA AW12EH2VHA AW18EH2VHA 14~115(-10~46) 14~115(-10~46) 14~115(-10~46) -15~75(-26~24) -15~75(-26~24) -15~75(-26~24) 208-230/60/1 208-230/60/1 208-230/60/1 DC Inverter Driven Rotary 15 15 25 12 14 18 Flare Flare Flare 1/4 1/4 1/4 3/8 3/8 1/2 51.5 51.5 74.1 66/20 66/20 83/25 50/15 50/15 50/15 Section 9 - Seacoast Application • The outdoor unit should be installed at least ½ mile away from the salt water, including seacoasts and inland waterways. If the unit installed from ½ mile to 5 miles away from the salt water, including seacoasts and inland waterways, please follow the installation instruction below. • Install the outdoor unit in a place (such as near buildings etc.) where it can be protected from sea breeze which can damage the outdoor unit. ODU Sea breeze Sea breeze ODU ODU Sea Sea • If you cannot avoid installing the outdoor unit by the seashore, construct a protection wall around it to block the sea breeze. • A protection wall should be constructed with a solid material such as Protection walls concrete to block the sea breeze and the height and the width of the wall should be 1.5 times larger than the size of the outdoor unit. Also, secure ODU over 28 in (700mm) between the protection wall and the outdoor unit for Sea breeze exhausted air to ventilate. Sea ODU • Install the outdoor unit in a place where water can drain smoothly. • If you dust on the outdoor unit heat exchanger. PAGE 8 INSTALLATION to clean the sea water and the [This page intentionally left blank.] www.Haier.com Model #: AW09EH2VHA, 1U09EH2VHA AW12EH2VHA, 1U12EH2VHA AW18EH2VHA, 1U18EH2VHA Issued Date: November 2015 Haier America, Wayne, NJ 07470 ©2015 Haier America Trading, LLC.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2015:11:04 08:51:24-06:00 Creator : Adobe InDesign CS5.5 (7.5.3) Modify Date : 2016:08:30 10:32:34-04:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2016:08:30 10:32:34-04:00 Creator Tool : Adobe InDesign CS5.5 (7.5.3) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 9039 bytes, use -b option to extract), (Binary data 12656 bytes, use -b option to extract) Instance ID : uuid:3c3a7bba-ff8a-4cc9-91aa-4a2d7842ff89 Document ID : xmp.did:FF98BE1B64C7E41183BE871A15540F9A Original Document ID : xmp.did:163943271B70E41191C9E61AC1A55563 Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:163943271B70E41191C9E61AC1A55563, xmp.iid:173943271B70E41191C9E61AC1A55563, xmp.iid:183943271B70E41191C9E61AC1A55563, xmp.iid:27EFBAAEF870E41183B0EAFD9C7FB145, xmp.iid:E8418B6CFA70E41183B0EAFD9C7FB145, xmp.iid:32F26FFBBD71E41183B0EAFD9C7FB145, xmp.iid:AB6E9C89C871E41183B0EAFD9C7FB145, xmp.iid:98C48EDFC871E41183B0EAFD9C7FB145, xmp.iid:99C48EDFC871E41183B0EAFD9C7FB145, xmp.iid:B24431EDC871E41183B0EAFD9C7FB145, xmp.iid:6559930BCB71E41183B0EAFD9C7FB145, xmp.iid:50A1F620CF71E41183B0EAFD9C7FB145, xmp.iid:FF6F4B2ACF71E41183B0EAFD9C7FB145, xmp.iid:2ECDEE45CF71E41183B0EAFD9C7FB145, xmp.iid:F5455875E773E41183B0EAFD9C7FB145, xmp.iid:69AA1497E773E41183B0EAFD9C7FB145, xmp.iid:25711A9BE973E41183B0EAFD9C7FB145, xmp.iid:26711A9BE973E41183B0EAFD9C7FB145, xmp.iid:A61C7283367BE411B9A3C5AB0E72EBB1, xmp.iid:F81D167FE67EE411B9A3C5AB0E72EBB1, xmp.iid:92BF5E7FE67EE411B9A3C5AB0E72EBB1, xmp.iid:0E395C8AE97EE411B9A3C5AB0E72EBB1, xmp.iid:64F8A709EA7EE411B9A3C5AB0E72EBB1, xmp.iid:B957065FFF7EE411B9A3C5AB0E72EBB1, xmp.iid:CA0C99EE1F7FE4119D57F9BC2A7155F9, xmp.iid:45161A22297FE4119D57F9BC2A7155F9, xmp.iid:5531E5DFC47FE4119D57F9BC2A7155F9, xmp.iid:64B088C4C67FE4119D57F9BC2A7155F9, xmp.iid:6212D122DB7FE4119D57F9BC2A7155F9, xmp.iid:6312D122DB7FE4119D57F9BC2A7155F9, xmp.iid:0FA6C326DB7FE4119D57F9BC2A7155F9, xmp.iid:92916574F27FE4119D57F9BC2A7155F9, xmp.iid:0BA914E07E80E4119D57F9BC2A7155F9, xmp.iid:A6D6C08B6984E4119613C0C76F8831C0, xmp.iid:212ECC0C6A84E4119613C0C76F8831C0, xmp.iid:70B82F2D7084E4119613C0C76F8831C0, xmp.iid:88D868C07184E4119613C0C76F8831C0, xmp.iid:8AD868C07184E4119613C0C76F8831C0, xmp.iid:DA7402AE7684E4119613C0C76F8831C0, xmp.iid:CF1718158384E4119613C0C76F8831C0, xmp.iid:F63DCE8B8384E4119613C0C76F8831C0, xmp.iid:E80962A48384E4119613C0C76F8831C0, xmp.iid:4B7A79988484E4119613C0C76F8831C0, xmp.iid:4C7A79988484E4119613C0C76F8831C0, xmp.iid:412976C08484E4119613C0C76F8831C0, xmp.iid:3CE3D888068AE411A3BEE25656014DA6, xmp.iid:EAFDA1960A8AE411A3BEE25656014DA6, xmp.iid:EBFDA1960A8AE411A3BEE25656014DA6, xmp.iid:0D41B1A50A8AE411A3BEE25656014DA6, xmp.iid:0E41B1A50A8AE411A3BEE25656014DA6, xmp.iid:5DFC9F330F8AE411A3BEE25656014DA6, xmp.iid:5EFC9F330F8AE411A3BEE25656014DA6, xmp.iid:5FFC9F330F8AE411A3BEE25656014DA6, xmp.iid:903BA5FACD8AE411A3BEE25656014DA6, xmp.iid:09DD57ABCE8AE411A3BEE25656014DA6, xmp.iid:0ADD57ABCE8AE411A3BEE25656014DA6, xmp.iid:0BDD57ABCE8AE411A3BEE25656014DA6, xmp.iid:5E57A061D68AE411A3BEE25656014DA6, xmp.iid:3138264D8B9AE411B018C752E6B1CCA3, xmp.iid:4F2229F2359CE411AFC28D39A3FB7E91, xmp.iid:8B075DE9379CE411AFC28D39A3FB7E91, xmp.iid:8C075DE9379CE411AFC28D39A3FB7E91, xmp.iid:798508AC3A9CE411AFC28D39A3FB7E91, xmp.iid:174F4BB43A9CE411AFC28D39A3FB7E91, xmp.iid:00D19F4E3C9CE411AFC28D39A3FB7E91, xmp.iid:2BC303B281B0E411A388D230AB78C275, xmp.iid:73FF46F181B0E411A388D230AB78C275, xmp.iid:C95063612DB1E411A388D230AB78C275, xmp.iid:247B87612DB1E411A388D230AB78C275, xmp.iid:2864CDB250B1E411A388D230AB78C275, xmp.iid:8AC9EE9A5DC6E411BB0ABBBA8E88FBBF, xmp.iid:C0B7D0E566C6E411BB0ABBBA8E88FBBF, xmp.iid:C080DEBF42C7E411AD81E4A9A16AD861, xmp.iid:703212B063C7E4118F0E94B78746F157, xmp.iid:1D21D3E963C7E41183BE871A15540F9A, xmp.iid:A348DAE963C7E41183BE871A15540F9A, xmp.iid:A448DAE963C7E41183BE871A15540F9A, xmp.iid:FF98BE1B64C7E41183BE871A15540F9A, xmp.iid:9469E51108C8E4119FE0F043516A22AA, xmp.iid:2A3595DB14E2E411801EB1879D1121A7, xmp.iid:8FD232A51EE2E411801EB1879D1121A7, xmp.iid:6EFA012B22E2E411801EB1879D1121A7, xmp.iid:84D07419C3E2E4118E5E93C426822537, xmp.iid:AA5C472CC6E2E4118E5E93C426822537, xmp.iid:9339BF530383E5119EF7883576DCA13B History When : 2014:11:19 14:19:36-06:00, 2014:11:20 09:52-06:00, 2014:11:20 09:52-06:00, 2014:11:20 15:03:31-06:00, 2014:11:20 15:15:59-06:00, 2014:11:21 14:35:50-06:00, 2014:11:21 15:51:24-06:00, 2014:11:21 15:53:48-06:00, 2014:11:21 15:54:11-06:00, 2014:11:21 15:54:11-06:00, 2014:11:21 16:09:21-06:00, 2014:11:21 16:38:35-06:00, 2014:11:21 16:38:51-06:00, 2014:11:21 16:39:37-06:00, 2014:11:24 08:37:47-06:00, 2014:11:24 08:38:43-06:00, 2014:11:24 08:53:09-06:00, 2014:11:24 10:19:20-06:00, 2014:12:03 15:51:19-06:00, 2014:12:08 08:28:36-06:00, 2014:12:08 08:28:37-06:00, 2014:12:08 08:50:24-06:00, 2014:12:08 08:53:57-06:00, 2014:12:08 11:26:40-06:00, 2014:12:08 15:19:45-06:00, 2014:12:08 16:25:37-06:00, 2014:12:09 11:00:27-06:00, 2014:12:09 11:14-06:00, 2014:12:09 13:39:48-06:00, 2014:12:09 13:39:55-06:00, 2014:12:09 13:39:55-06:00, 2014:12:09 16:26:44-06:00, 2014:12:10 09:11:54-06:00, 2014:12:15 08:52:54-06:00, 2014:12:15 08:52:54-06:00, 2014:12:15 09:36:45-06:00, 2014:12:15 09:48:02-06:00, 2014:12:15 10:23:18-06:00, 2014:12:15 10:23:18-06:00, 2014:12:15 11:52:05-06:00, 2014:12:15 11:55:24-06:00, 2014:12:15 11:56:06-06:00, 2014:12:15 12:02:55-06:00, 2014:12:15 12:04:02-06:00, 2014:12:15 12:04:02-06:00, 2014:12:22 12:15:39-06:00, 2014:12:22 12:44:40-06:00, 2014:12:22 12:45:06-06:00, 2014:12:22 12:45:06-06:00, 2014:12:22 12:58:24-06:00, 2014:12:22 13:17:42-06:00, 2014:12:23 10:05:52-06:00, 2014:12:23 10:05:52-06:00, 2014:12:23 12:03:20-06:00, 2014:12:23 12:08:17-06:00, 2014:12:23 12:28:10-06:00, 2014:12:23 12:29:05-06:00, 2014:12:23 13:23:03-06:00, 2015:01:12 12:46:21-06:00, 2015:01:14 15:40:23-06:00, 2015:01:14 15:54:28-06:00, 2015:01:14 15:56:52-06:00, 2015:01:14 16:14:13-06:00, 2015:01:14 16:14:27-06:00, 2015:01:14 16:25:55-06:00, 2015:02:09 11:33:01-06:00, 2015:02:09 11:34:47-06:00, 2015:02:10 08:01:59-06:00, 2015:02:10 08:01:59-06:00, 2015:02:10 12:14:48-06:00, 2015:03:09 08:10:06-05:00, 2015:03:09 09:16:37-05:00, 2015:03:10 11:30:22-05:00, 2015:03:10 15:26:09-05:00, 2015:03:10 15:27:46-05:00, 2015:03:10 15:27:46-05:00, 2015:03:10 15:29:10-05:00, 2015:03:10 15:29:10-05:00, 2015:03:11 11:02:51-05:00, 2015:04:13 14:39:53-05:00, 2015:04:13 15:49:57-05:00, 2015:04:13 16:15:10-05:00, 2015:04:14 11:27:10-05:00, 2015:04:14 11:49:10-05:00, 2015:11:04 08:50:01-06:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Derived From Instance ID : xmp.iid:A448DAE963C7E41183BE871A15540F9A Derived From Document ID : xmp.did:A348DAE963C7E41183BE871A15540F9A Derived From Original Document ID: xmp.did:163943271B70E41191C9E61AC1A55563 Derived From Rendition Class : default Doc Change Count : 5135 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 10EXIF Metadata provided by EXIF.tools