Haier Hwm60 111S Users Manual 脣脮碌陇HWM60

HWM60-111S to the manual 21f424b3-8e12-4cff-8958-d987fbf783af

: Haier Haier-Hwm60-111S-Users-Manual-260804 haier-hwm60-111s-users-manual-260804 haier pdf

Open the PDF directly: View PDF .
Page Count: 18

Twin-tub Washing Machine User's manual

This manual is for

HWM60-111S

Please read this manual

carefully before using.

Retain it for future reference.

Contents

Safety precautions

Installation and adjustment

Preparation before washing

The musts in washing

Usage of the detergent

Washing sequence

Disposal after washing

Packing list *Specification

Names of the parts

Trouble-Shooting *Answer to question

1

Meaning and description of the symbols

Warning sign

Forbidding sign

Contents marked with that symbol are related

to the safety of the product and the personal

safety of the users. Please operate in strict

conformity to the contents, otherwise it may

cause damage of the machine or injure the

personal safety of the user.

Contents marked with that symbol are actions

forbidden to perform. Performing of those

actions may result in damage of the machine

or injure the personal safety of he user.

Please check if the power receptacle has good earthing

condition before using to guarantee your safety.

Names of the parts

Control panel

Spin water-filling entrance

Spin timer

Wash selector

Wash timer

Transparent lid

Overflow filter

Wash water-filling entrance

Water level adjusting lever

Drain hose hook

Lint filter(Installed by user)

Pulsator

Wash tub

Drain hose

Wash tub cover

Outer cover of the spin tub

Inner cover of the spin tub

Spin tub frame

Spin tub

Cabinet

Power cord

Base frame

2

Safety precautions

Please insert the power cord into

special receptacle with rated vol-

tage.Be sure to use single-phase

three pins receptacle.The earthing

terminal of the receptacle must be

earthed reliably.If possible,please

adopt electric leakage protector.

When the machine is normally

using, please put the power plug

at the location easily to be insert-

ed and extracted by hand. Be sure

to pull the plug off when there's

power failure, or the machine is

being moved, cleaned orwhen it

is idle.

If the power cord is bad, to avoid risk it is required to replace it by the

technicians ofour special shop or the after-sale service department.

Keep the pin of the power plug clean.

Earth

Do not put the machine at damp

place like the bathroom . Never

wash it with water. Do not place

wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing machine is installed

on ground with carpet , do not block the

ventilation hole with carpet.

Do not wash water-proof laundries like

the raincoat, bike covers etc. to avoid

abnormal vibrations in spinning.

Do not let the machine share one receptacle

with other electric appliances. If the power

plug is damaged, or the plugging into the

receptacle is loose, do not use the plug any

more.

Ventilation hole at

the bottom of the

washing machine

3

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Safety precautions

Do not put any hot or heavy items

( such as the kettle with hot water )

on the washing machine.

Do not decompose, repair or alter the

machine by yourself.

Handicapped or children without care

shall not use the machine.

Keep the machine away from direct

sunlight and heat source like the

heater.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.).

Petrol

Thinner

To protect your laundries and wash-

ing machine, please take out all of the

coins, buttons, sand, hairpin and

other foreign materials before washing.

Please check if the water faucet is open,

and if the connection of the water inlet

pipe is proper.

It is suggested to use foamless washing

powder.

Overflow filter

Lint filter

If the extra hose is too long, cut it either

at point A or B.

<10cm

BA

> 30mm

<1.5m

4

Installation and adjustment

Please install and adjust the machine according to the requirement of

the manual. It is very important to your security and correct operating

the machine.

Install the lint filter

After opening the package,please take out the lint

filter from the document bag,install it to the overflow

filter of the wash tub.See to the figure.

Usage of the drain hose

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be

less than 10cm , or the drainage will

not be smooth enough and cause

incomplete drainage.

2.Do not tramp or press the drain hose.

3.If the drain hose is too long, cut it at mid point.

To make smooth drainage, cut the front end of

the hose slantingly.

4.If extra drain hose is needed , please make

separate purchase. The inner diameter of the

extra hose shall not less than 30mm, and the

length shall not exceed 1.5m.

Filling water from wash water-filling entrance

Water inlet hose

Water-filling jointer

Push

Control handle

Wash water-filling entrance

Insert the water inlet hose into the water-filling

entrance, then push the water-filling jointer into

the entrance on the control panel. (To dismantle

the water inlet pipe, just push the control handle

as indicated in the figure and pull it out)

The appliance is to be connected to the water

mains using new hose-sets and that old hose-

sets should not be reused.

5

How to change the direction of the drain hoses

Figure 1 indicates the ex factory installation

position of the drain hose.

Put soft items on the ground. Lean the machine

down gently with the front surface facing the

ground. Take off the drain hose from the cabinet.

Take the hose out of the fixing groove.

(See to Figure 2).

Embed the drain hose into the groove along the

side of the spin tub in the order of (1)~(3), heading

for the side of the spin tub. (See to Figure 3).

Embed the drain hose into the groove with

hands. Take care not to damage the drain

hose in fastening the fixing clamp.

Figure 1

Figure 2

Figure 3

Figure 4

Embed into the

groove in turn

Extend the drain hose from the side of spin tub

Soft item

Extend to the

spin tub side

Take out the drain hose from the fixing groove.

Extend it fromthe rear side as per the direction

of the arrow. (When the drainhose is extended

from the rear side, it can be hung on the

point for drain hose at the two sides of the cabinet.)

(See to Figure 4).

Soft item

Back

Front

Extend the drain hose from the rear side

Select the water level

Select water level according to the

quantity of the laundries.

Set the water level adjusting lever

to needed line.

Water level

indicator

Maximum

about 43L

about 36L

about 30L

Minimum

Medium

Max.

Med.

Min.

6

Preparation before washing

1.Connect the water inlet hose.

2.Confirm that the washing machine is earthed

reliably . Then insert the power plug into the

receptacle. Do not connect the earth terminal

to the gas pipe and tap water pipe.

3.Put down the drain hose .

4.Slanting or uneven ground may result in

unstable working or abnormal noise. Please

make the machine stand horizontally.

Preparation before washing

Pay attention to followings before washing the laundries

Check if

the laundries

has special

requirement

on washing

Clear the

pocket. Take

out the coins,

sand, hairpins

etc.

Tie the long

strips; fasten

the buttons;

close zippers.

When the pulsator

is running , the

buttons of the

laundries may

cause noise. For

the sake of

discretion, please

put the laundries

with buttons into

other laundries.

The quantity of

the laundries

shall not be too

large. Stretch

and loosen the

laundries before

putting them in

the tub.

a. Check if the laundries are applicable for washing with machine.

b. Divide the laundries that are not colorfast from other laundries.

c. Put those laundries difficult to absorb water into water with hand.

d. For those laundries with heavy soil, please first remove the dirt like

mud or dust. For the parts with heavy soil, please apply detergent on

them in advance, which can make it easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn

it over before putting in.

f. Do not put those laundries polluted by chemicals into the washing

machine directly.

7

The capacity of washing and spinning of the

machine refer to the largest weight of the

standard laundries under dry condition that can

be washed or spinned in one time. Laundries

quantity in one washing cycle shall be lower

than the rated capacity. .

The thickness ,size , type of the cloth will influ-

ence the actual washing capacity. It is suit-

able to put in reasonable amount of laundries

and the laundries can be turned round in wash-

ing for one time washing.

Do not select " Maximum " water level for

laundries less than 2.4kg, so as to avoid

splashing of water.

The musts in washing

How to use the whitener

Fill water to decided level. Dilute

the whitener with container.

Pour it slowly into thewashing tub.

Avoid using whitener on laun-

dries with color or pattern as they

are prone to lose color.

The whitener shall not touch

the laundries directly.

Direct dissolved in the machine:

1.Fill small quantity of water.

2.Add the powder . Run for 30

seconds to dissolve it completely.

3.Put it in the laundries. Select suitable

water level.

The instant dissolving of the washing

powder:

1.Prepare warm water of 30 C and a

container.

2.Add the powder while stirring to fully

dissolve it.

The powder is more prone to pollute the

laundries than the detergent. Therefore

please use it with proper quantity.

Dosage of different washing powder is

different. Please refer to the instruction

of the washing powder for the detail

dosage.

Refer to the user's manual for

the usage and quantity of the

whitener.

For powder whitener, please

dissolve it before using.

It is suggested not to use high sudsingdetergent.

How to use the washing powder

Usage of the detergent

8

Washing sequence

OFF

OFF

DRAIN

STRONG

Figure 1

Figure 2

Figure 3

Figure 4

WOOL WOOL

WOOL

SPIN TIMER

WASH TIMER

WASH TIMER

WASH SELECTOR

LINEN

LINEN

Wash

SILK SILK

SILK

COTTON

COTTON

DRAIN

STRONG

WASH SELECTOR

WASH SELECTOR

1. Fill the water and add the dissolved washing

powder to make the water level reach the preset

position. (Figure 1)

Run washing program for some time to stir and

dissolve the powder completely.

2.Put in the laundries. If the water quantity is

insufficient, please add water.

3.Select the current.

Select the strength of the current according to

the laundries. (Figure 2)

4.Select the washing time

Select the washing time according to the laundries.

(Figure 2)

5.After washing, set the "WASH SELECTOR" at

"DRAIN". (Figure 4).

SOFT

SOFT

SOFT

STRONG

Wash timer

(To set to below 2 minute,

first set to 5 minute then

turn it back. it can increase

the service life of the timer).

Wash selector

(Soft current,

strong current)

Spin timer

(To set to below 1 minute,

first set to 2 minute then

turn it back. it can increase

the service life of the timer).

Spin water-filling entrance

OFF

DRAIN

Spin water-filling entrance

9

Midway spinning

Push

Push

Proper Proper

Outer cover of

The spin tub

Inner cover of

The spin tub

The laundries

are slanting

Gland

No gland

1.Put the laundries into the spin tub evenly and smoothly.

2.Spin (1) Put the gland in properly.

Please put in the gland properly even if the

laundries quantity is small.

(2) Close the inner and outer cover of the spin tub.

(3) Spin for 1-2 minutes.

(1) Open the outer cover of the spin tub.

(2) Insert the water inlet hose into the spin

water-filling entrance on the control panel.

Fill water for about 1 minute.

(3) Close the outer cover of the spin tub.

Spin for 1-2 minutes.

Water inlet hose

Spin water-filling

entrance

3.Run the foam-removing spinning.

10

Rinse with stored water

Rinse with water-filling

1. Put the laundries into the wash tub. Select suitable current according to

the laundries.

2. Fill water to preset water level.

3. Rinse

Adjust the wash timer to 2-3 minutes to do rinsing.

When the laundries quantity is below 2.4kg, please use STONG

current.If you use "SOFT " current, it may splash.

Rinsing

(Repeat the midway spinning and

rinsing with stored water for 2-3 times)

1.Put the laundries into the wash tub. Select

suitable current according to the laundries.

2.Adjust the water level

Set the water level with water level adjusting

lever according to the laundries quantity.

Then fill suitable water continuously.

3.Rinse

Adjust the wash timer to 5-7 minutes to do

rinsing.

11

Selection of the spin time list 3

Laundries Spin time

(minutes)

About 4~5

Bed sheet or

blanket

About 2~4

Underwear

(knitwear)

Swear

(chemical fiber) About 1~2

Within 1 minute

Blending thin

laundries

1. Put the laundries into the spin tub

evenly and smoothly.

2. Press the gland in the tub properly.

Close the inner and outer cover of

the spin tub.

3. Spin

Select suitable spin time according

to the laundries, and do spinning.

During spinning, if there's abnormal

sound, it is generally owing to slanting

placement of the laundries. Please

stop the machine and re-order the

laundries.

In spinning, it will pause the work if you open the outer cover of the spin

tub. Close it to resume the spinning.

Spinning

To do spinning and draining or rinsing

with water-filling together, please first

do spinning for around 1 minute, then

do draining or rinsing with water-filling.

Otherwise the spinning will stop owing

to too much water stored in the spin tub.

12

After using, please clean the lint and foreign materials of the lint filter and

overflow filter in time. Otherwise it may influence your using the machine.

Please first pull off the power plug from the receptacle before cleaning.

1 Take off the overflow filter.

As indicated in the figure, nip the elastic fixing

claw and pull it to the direction of the arrow to

take it off.

Cleaning the overflow filter

Too much lint on the overflow filter will influence

the normal usage of the machine. Please

clean it every two months. Elastic fixing

claw

Figure 2

Figure 3

Figure 1

1. Take off the lint filter

Put hand at the indicated position.

Push down to take it off. ( See to

Figure 1)

2. Clean the lint

Put it in water and clean while it is

still wet.(See to Figure 2)

3. Install the lint filter

After cleaning, insert the bottom

of the lint filter ( marked with

"down side") into the overflow filter ,

then push the upper part of the

filter in ( marked with " up side ").

(See to Figure 3)

The lint filter must be used during washing.

It must be cleaned in time after each using.

Cleaning the lint filter

Disposal after washing

13

Wipe the complete unit with soft

cloth twisted dry.

Wipe with neutral detergent if too dirty

Do not wash it directly by water

Cleaning the overflow filter

2. Take off the corrugation pipe.

Dismantle the upper part of the

corrugation pipe inside the

overflow filter ( as indicated in

Figure 1).

3. Cleaning the overflow filter

Clean the lint around the filter

and flush with tap water.

4. Install the overflow filter.

(1).Install the corrugation pipe.

(2).Insert the mounting plate at

the bottom of the filter into

the valve cover.

(3).Hang up the hook at the left

upper side.

(4).Push the upper part in as

indicated in Figure 2.

Corrugation

Pipe

Hook

Figure 1

Figure 2

Water level

adjusting lever

After washing, dismount the water inlet

hose.

Do not store water in the tub for long

period. Discharge the water immediately

after each using.

Pull off the power plug and hang up the

power cord.

Hang up the drain hose.

Wipe off the water drops on the surface

and inside the tub with clean soft cloth.

Open the cover of the wash tub and the

inner/outer cover of the spin tub for

some time (about one hour), then close

them.

Disposal of the complete unit

Thinner

Alcohol

Petrol

14

Trouble-shooting Answer to question

When the remained water is frozen

If the laundries fall to the outer side of the spin tub,

please take them out immediately.

1.Dismantle

As indicated in the figure, push the point marked

with " " to pull the spin tub frame to oblique

upwards to dismantle it.

2.Install

After install the back edge of the spin tub frame to

proper position, push the four points marked with

" " by force to reset it.

Please check carefully. The laundries may fall to the

lower part of the outer side of the spin tub (as indicated

in the figure).

If the laundries fall to the outer side of the spin tub, during

spinning the draining will get blocked and the rotation speed

of the spin tub is reduced.

Spin tub

Laundries

Spin tub frame

If the laundries fall to the outer side of the spin tub

Prevent the freezing (be sure to discharge the water

completely after using)

After complete draining, set the "WASH SELECTOR"

at "STRONG" or "SOFT". If it is set at "DRAIN",

it will be rather difficult for the frozen water to melt.

When the water is frozen

Pour hot water below 50 into the wash tub

to soak it completely. Then turn the pulsator

with hands gently. Please confirm the drainage

can work normally before next using.

2~3L

Below 50

15

Trouble-shooting Answers to question

(If there's breakdown, please pull off the power plug before checking) The following

phenomena are not breakdowns sometimes. Please confirm again before sending

it to repair. If there are real breakdowns, please come to the special maintenance

department or after-sale service department of our company. Do not repair it by yourself.

Phenomena The reason

The machine does

not act.

Is there power failure?

Is the power plug loose?

Is the pulsator twisted by foreign materials?

Is the drain hose put down?

Is the drain hose frozen?

Is the drain hose blocked by foreign material?

Are there laundries falling to the outer side of

the spin tub?

There's abnormal

sound during washing

Are there hair pin, coins or metal items brought

inside the tub?

Is the machine slanting?

Is the gland pressed evenly?

Are there laundries falling to the outer side of

the spin tub?

Are the laundries in spin tub too much?

It is the water remained in the factory inspection

of performance.

There may be some

waterflowing out of

the drain hose in the

first use of the

machine.

There's abnormal

sound and violent

vibration during

spinning

There's abnormal

soundduring washing

16

Water inlet hose

Water-filling jointer

Gland

Lint filter

Packing list

Twin-tub washing machine

Name Quantity

User's manual One piece

One piece

One piece

One piece

One piece

One set

Water level/Water quantity (about)

Maximum/43L Medium/36L Minimum/30L

Injection pressure(MPa

Specification