Haisen Technology HDM02 5.8G microwave sensor module User Manual HDM02 x

Download:
Mirror Download [FCC.gov]
Document ID	3664768
Application ID	zv3cFnS1KKRzIo2fWa3fuQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.34kB (91740 bits)
Date Submitted	2017-12-06 00:00:00
Date Available	2017-12-06 00:00:00
Creation Date	2017-12-05 19:04:56
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2017-12-05 19:04:56
Document Title	Microsoft Word - HDM02_User Manual.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

Module specification
1. Technical date:
No.
Item
Value
Unit
Operating Voltage
V(DC)
Operating Current
≤9
mA
Frequency Range
5.8G±75M
HZ
Frequency tolerance
±5M max.(-30～+55℃)
HZ
Antenna gain
5.42
dbi
second harmonic
≤1
uw
Microwave power
≤1
mw
Detection range(straight
stretch)
≥10
Dimension
28 x 17 x 7.1
mm
2. PIN Description:
No.
Name
Description
VCC
Supply Power ( +5V DC )
GND
Ground
IF
Output signal
Declaration
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Espressif may cause
harmful interference and void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
OEM/Integrators Installations User Manual
Note: The module is limited to OEM installation ONLY; The OEM integrator is responsible for
ensuring that the end‐user has no manual instructions to remove or install module.
The module is limited to installation in mobile or fixed application.
The separate approval is required for all other operating configuration, including portable
configuration with respect to Part 2.1093 and different antenna configuration.
This product is mounted inside of the end product only by professional installers OEM. They use
this module with changing the power and control signal setting by software of end product
within the scope of this application. End user can not change this setting.
The equipment complies with RF exposure limits. This module is limited to installation in mobile
or fixed applications. The antenna used for this transmitter must not be co‐located or operating
in conjunction with any other antenna or transmitter.
If the FCC identification number is not visible when the module is installed inside another device,
then the outside of the device into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: 2AN7F‐HDM02 ”
when the module is installed inside another device, the user manual of this device must contain
below warning statements;
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2017:12:05 19:04:56+08:00
Modify Date                     : 2017:12:05 19:04:56+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 11.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - HDM02_User Manual.docx
Creator                         : Administrator
Document ID                     : uuid:1c5db3b1-a23a-4cf0-99af-1656cb30e625
Instance ID                     : uuid:a3478c3e-3c6c-4fa0-b646-434879ebf5e4
Page Count                      : 3

EXIF Metadata provided by EXIF.tools