Handheld Group 14249-RF2 Handheld Device User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	3788094
Application ID	Cedgux7c0o3w6VPPWdEnmA==
Document Description	Users Manual-1
Short Term Confidential	Yes
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	467.38kB (5842241 bits)
Date Submitted	2018-03-20 00:00:00
Date Available	2018-09-17 00:00:00
Creation Date	2018-02-26 10:38:49
Producing Software	doPDF Ver 7.3 Build 387 (Windows 7 Business Edition (SP 1) - Version: 6.1.7601 (x64))
Document Lastmod	2018-03-12 13:52:27
Document Title	Users Manual-1

NAUTIZ X9
MANUAL
COPYRIGHT
Copyright © 2018 Handheld Group AB. All Rights Reserved.
This document contains proprietary information protected by copyright. No part of this manual may be
reproduced by any mechanical, electronic, or other means in any form without prior written permission of the
manufacturer.
DISCLAIMER
The information in this document is subject to change without prior notice in order to improve the reliability,
design and function. It does not represent a commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or
consequential damages arising from the use or inability to use the product or documentation, even if advised
of the possibility of such damages.
ABOUT THIS MANUAL
This user’s manual provides the general information and installation instructions for the product. The manual is
meant for the experienced users and integrators with hardware knowledge of personal computers. If you are
not sure about any description in this manual, consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference for any necessary maintenance
in the future. Thank you for choosing a Handheld product.
Ver 1.0
DECLARATION OF CONFORMITY
CE
The CE symbol on your product indicates that it is in compliance with the directives of the Union European
(EU). A Certificate of Compliance is available by contacting Technical Support.
This product has passed the CE test for environmental specifications when shielded cables are used for
external wiring. We recommend the use of shielded cables.
FCC
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This device is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the
Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.
Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels. The FCC has granted an Equipment
Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this device is on file with the FCC and can be found under the
Display Grant section of www.fcc.gov/eot/ea/fccid . To ensure that RF exposure levels remain at or below the
tested levels, use a belt clip, holster, or similar accessory that have no metallic component in the assembly
and must maintains a minimum separation distance of 10mm between your body and the device.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Ver 1.0
RoHS
Handheld Group AB certifies that all components in its products are in compliance and conform to the
European Union’s Restriction of Use of Hazardous Substances in Electrical and Electronic Equipment (RoHS)
Directive 2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose of the directive is to prohibit
the use of lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB), and
polybrominated diphenyl ethers (PBDE) in electrical and electronic products. Member states of the EU are to
enforce by 7/1/2006.
Handheld Group AB hereby states that the listed products do not contain unintentional additions of lead,
mercury, hex chrome, PBB or PBDB that exceed a maximum concentration value of 0.1% by weight or for
cadmium exceed 0.01% by weight, per homogenous material. Homogenous material is defined as a
substance or mixture of substances with uniform composition (such as solders, resins, plating, etc.). Lead-free
solder is used for all terminations (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility of the earth where we live, Handheld
hereby confirms all products comply with the restriction of SVHC (Substances of Very High Concern) in (EC)
1907/2006 (REACH--Registration, Evaluation, Authorization, and Restriction of Chemicals) regulated by the
European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
Ver 1.0
Symbols Description
This symbol of “CAUTION” indicates that there is a danger of injury to the user or a risk of damage
to the product, should warning notices be disregarded.
Important Safety Instructions
Read these safety instructions carefully:
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or letting it fall may cause
damage
3. Make sure the correct voltage is connected to the equipment.
4. For pluggable equipment, the socket outlet should be near the equipment and should be easily
accessible.
5. Keep this equipment away from humidity.
6. Disconnect this equipment from the A/C outlet before cleaning it. Use a moist cloth. Do not use liquid
or sprayed detergent for cleaning.
7. To fully disengage the power to the unit, please disconnect the power from the AC outlet.
8. Do not scratch or rub the screen with a hard object.
9. Never use any of the solvents, such as Thinner Spray-type cleaner, Wax, Benzene, Abrasive cleaner,
Acid or Alkaline solvent, on the display. Harsh chemicals may cause damage to the cabinet and the
touch sensor.
10. Remove dirt with a lightly moistened cloth and a mild solvent detergent.
1. Then wipe the cabinet with a soft dry cloth.
11. The openings on the enclosure are for air convection and protect the equipment from overheating.
DO NOT COVER THE OPENINGS
12. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
13. If the equipment will not be used for a long time, disconnect it from the power source to avoid damage
by transient overvoltage.
14. Never pour any liquid into openings. This may cause fire or electrical shock.
15. Never open the equipment. For safety reasons, the equipment should be opened only by qualified
service personnel.
Ver 1.0
16. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
17. The sound pressure level at the operator’s position, according to IEC 704-:1982, is no more than 70dB(A).
18. Keep this User’s Manual for later reference.
19. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE
TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE
EQUIPMENT.
Do not use the power adapter that isn’t made for the equipment. Supplying the equipment with inappropriate voltage may cause
harm to the battery or, even worse, burn the equipment.
To prevent possible hearing damage, do not listen at high volume levels for long periods
Ver 1.0
Rechargeable Battery Pack Safety
With very little care, you can optimize the battery life and maximize the lifespan of the battery. Most
importantly, use only the equipment in its ideal operating temperature – do not leave it in a hot trunk during the
summer.
Important Terms to Understand
“Battery life” means the time the equipment will run before it must be recharged (sometimes this is also called
“playtime” or “runtime”).
“Battery lifespan” means the total amount of time your battery will last before it must be replaced.
Using the Equipment for the First Time
Be sure to fully charge the equipment when charging the equipment for the first time.
Long-Term Storage & Maintenance
If you are putting away the battery for more than three months, it is recommended that the battery should be
stored separately and fully charged, and get recharged every three months. If you store an uncharged battery,
it could fall into a deep worn-out state which would render it incapable of holding any charge. Be sure to store
the equipment and battery at the proper temperature (as described in 1.5 Specifications).
Battery Lifespan
The removable batteries for the equipment are designed to retain up to 80% of their original capacity after 300
charging and recharging cycles when properly maintained. You may choose to purchase new battery when it
no longer holds the sufficient charge that meets your needs.
•
The lithium-ion battery is currently one of the most popular battery packs.
•
The best advantage is that it has no memory effect, so users needn’t worry about that issue. Users
can charge the battery anytime whether it is fully drained or not. However, it’s recommended that
users drain the battery until the system shows power shortage warning and then recharge the battery.
Doing so is helpful to the reliability of your battery.
•
Don’t use the battery pack as a power supply for other equipment.
•
Don’t expose the battery to elevated heat situations such as under direct sunlight in a car or near fire.
•
Don’t disassemble the battery, or the battery leakage might cause skin or eye injury. If electrolyte
leaking from the battery contacts your skin or clothing, immediately flush it with running water. If it
splashes into eye, rinse the eye at least 15 minutes with clean water and then seek medical attention.
•
To avoid battery leakage or explosion, don’t discard the battery into water or fire, or put them near a
heat source such as a gas stove or an oven.
•
If you are putting away the battery for more than three months, it is recommended that the battery
should be stored separately and fully charged, and get recharged every three months. If you store an
uncharged battery, it could fall into a deep worn-out state which would render it incapable of holding
any charge. Be sure to store the equipment and battery at the proper temperature (as described in
1.5 Specifications).
•
Use the appropriate container to store the battery such as a paper box. Do not allow a metal object to
touch the terminal of the battery.
•
The battery consists of precise electrical components and cells. Do not drop or hit the battery.
Ver 1.0
Disposing of the Equipment
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste.
This includes monitors and electrical accessories, such as signal cables or power cords. When you need to
dispose of your display products, please follow the guidance of your local authority, or ask the shop where you
purchased the product, or if applicable, follow any agreements made between yourself. The mark on electrical
and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact
your local authority so as to comply with the correct disposal method.
Additional Information & Technical Support
You can download the related technical documents such as datasheet and user’s manual as well as driver on
our website.
Please do not hesitate to call or e-mail our customer service when you still cannot get the information you
need.
https://www.handheldgroup.com/support-rugged-computers/knowledgebase/
E-mail: support@handheldgroup.com
Ver 1.0
Warranty
This product is warranted to be in good working order during the warranty period. Should this product fail to be
in good working order at any time during this period, we will, at our option, replace or repair it at no additional
charge except as set forth in the following terms. This warranty does not apply to products damaged by
misuse, modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential
damage resulting from the use, misuse of, or inability to use this product. Vendor will not be liable for any
claim made by any other related party.
Vendors disclaim all other warranties, either expressed or implied, including but not limited to implied
warranties of merchantability and fitness for a particular purpose, with respect to the hardware, the
accompanying product’s manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specific legal rights.
Return authorization must be obtained from the vendor before returned merchandise will be accepted.
Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise
Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.
Ver 1.0
1. INTRODUCTION
1.1. Product Highlights
•
Support Android 7.0
•
Quad-core ARM Cortex-A53 1.3GHz
•
Multiple connectivity including WLAN, WWAN, Bluetooth, NFC and 2G/3G/LTE
•
Worldwide modem capability (Support FDD/TDD-LTE, WCDMA, CDMA2000 1xEV-DO
GSM/GPRS/EDGE)
•
IP67 rated water and dust resistance
•
Drop proof: Up to 1.5m
•
Accelerometer, Magnetometer, Gyroscope, Light sensor, GPS & Barometer
•
Built-in 1D/2D barcode reader
1.2 Package Contents
Upon opening the package, carefully inspect the contents. If any of the items is missing or appears damaged,
contact your local dealer or distributor. The package should contain the following items:
Nautiz X9 Main Body
Ver 1.0
Standard Battery Power Adapter
Quick Start Guide
10
1.3 Parts of the Device
NOTE Do not remove transparent film unless you are using the pistol grip accessory
Ver 1.0
11
1.4 Dimensions
Ver 1.0
12
1.5 Specifications
System
CPU
Quad Core ARM Cortex-A53 1.3GHz
OS
Android 7.0
Memory
2GB LPDDR2
Storage
16 GB eMMC
Peripherals and Devices
Front: 2.0 MP camera
Camera
Rear: 13.0 MP camera with Auto-Focus and Flashlight
Magnetometer (M-Sensor/E-Compass) Accelerometer (G-sensor)
Gyroscope Barometer Proximity sensor
Ambient light sensor
Sensor
Magnetometer (M-Sensor/E-Compass) Accelerometer (G-sensor)
Gyroscope Barometer Proximity sensor
Ambient light sensor
Barcode Scanner
2D barcode reader with physical trigger button
Audio & Vibrator
1 x built-in microphone
1 x built-in speaker (1W)
1 x 3.5mm stereo headphone/microphone combo jack
1 x vibrator
FM radio
Wireless
WLAN
Integrated IEEE 802.11a/b/g/n
Bluetooth
Bluetooth 4.1 (BLE, HS compliant)
WWAN (Global)
2G GSM/GPRS/EDGE (900/1800)
3G WCDMA (B5, B8)
4G (B1, B3, B8, B20, B38, B39, B40)
WWAN (NA)
Ver 1.0
2G GSM/GPRS/EDGE (900/1800)
3G WCDMA (B2, B5)
3G CDMA2000 (BC0/BC1)
LTE (B2, B4, B12, B13, B17)
13
GPS
GPS/GLONASS
NFC
Yes
I/O Interface
USB Port
1 x micro USB 2.0 port High Speed / OTG Compatible
SD Slot
1 x microSD card slot
SIM Cart
1 x micro-SIM (3FF) socket supporting 2G/3G/LTE
1 x micro-SIM (3FF) socket supporting 2G only
LCD Display
Size/Type
Resolution
Brightness (cd/m²)
Touch Screen
5“ TFT LCD
720(W) x 1280(H)
400 cd/m²
5 points capacitive touch (PCT)
Power Supply
Battery Type
Battery Capacity
Battery Life
Adapter Input
Adapter Output
Lithium-ion rechargeable battery, field replaceable
Typical 3.7V, 4800mAh
TBD
AC100~240C, 50~60 Hz
5V/2A (10W)
Mechanical & Environmental
Ingress Protection
IP67, Up to 1.5m drop resistance.
Operating Temp.
-20°C ~ 55°C (-4°F ~ 131°F )
Storage Temp.
-20°C ~ 60°C (-4°F ~ 140°F)
Operating Humidity
5~95% RH
Dimensions (mm)
165.8(H) x 86(W) x 25.6(D)
Weight
under 385g (0.85lb) (with battery)
Ver 1.0
14
2. GETTING STARTED
2.1 Installing microSD and SIM Card
To install the microSD card and/or SIM card(s):
1. Pull the back cover release latch towards the bottom of the phone to unlock the latch.
Latch locked
Latch unlocked
2. Insert a small flathead screwdriver into the notch and gently pry up the cover.
3. Remove the battery, if inserted. The battery is secured by a red slider. Move the slider to the right so
that you can remove the battery.
Move the slider to the right to unlock the battery.
Ver 1.0
15
4. Insert the SIM cards / microSD card following the direction as shown in the graphic.

To insert SIM card(s): The device comes with two SIM card slots, each with their own supported
networks. SIM card slot 1 supports 2G, 3G and 4G while slot 2 supports 2G network. Make sure to
insert your SIM cards correctly.
SIM slot 2: 2G
SIM slot 1: 2G/3G/4G

To insert a microSD card: Push the microSD card cover toward SIM slot 1 to lift it up. Insert a
microSD card following the direction as shown in the graphic. Then push the microSD card cover
back into its original position to lock it.
5. Insert the battery back to the compartment while ensuring gold contacts align with the device contacts.
Then move the slider to the left to secure the battery.
Move the slider to the left to secure the battery.
Ver 1.0
16
6. Replace the back cover and push the latch towards the cover to lock it.
After the SIM card(s) are properly installed, the device is ready to use the cellular network. See 3.3 Using
Cellular Network to know how to use them.
2.2 Charging the Battery
You can charge the Nautiz X9 via the provided power adapter or computer USB
connection.

Due to shipment, the battery is partially drained when the package is
delivered to you. Be sure to charge the battery to full when you are
charging it for the first time.

To use the power adapter: Connect the power adapter to your power
outlet and connect the USB end to the USB port on the device.

To use a computer USB connection: Using a USB cable, connect small
end to the USB port on the device and the other end to the USB port on a
computer.
WARNING: Use only the power adapter that comes with your device. Using a different power adapter may damage your
device and may result in poor performance. It may also invalidate warranty applying to the device.
2.2.1 Checking the Battery Level
When you charge the Nautiz X9, the LED indicator will show the charging status as below:

Charging in progress: Red, solid

Fully charged: Green, solid
Ver 1.0
17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Modify, Annotate, Fill forms, Extract, Assemble, Print high-res
Page Count                      : 17
Page Layout                     : OneColumn
Page Mode                       : UseNone
Producer                        : doPDF Ver 7.3 Build 387 (Windows 7 Business Edition (SP 1) - Version: 6.1.7601 (x64))
Create Date                     : 2018:02:26 10:38:49+08:00
Modify Date                     : 2018:03:12 13:52:27+08:00

EXIF Metadata provided by EXIF.tools