Hangshi Technology MD156 Bluetooth+2.4G Mouse User Manual
Shenzhen Hangshi Technology Co., Ltd Bluetooth+2.4G Mouse
User Manual
MD156 Bluetooth+2.4G Mouse
Packing content
Mouse*1 2.4G receiver*1 AAA battery*2 Manual *1
Specifications
Connection mode
Bluetooth & 2.4GHz
Connected by
Bluetooth V3.0 & 2.4G receiver
Three Keys
Left, middle(roller),right
DPI level
4 levels: 800dpi,1000dpi, 1200dpi(default),1600dpi
Power support
2*AAA batteries (included)
Operating distance
Bluetooth:8 meters
2.4GHz: 8 meters
Working current
Bluetooth: 10mA
2.4GHz: 10mA
Dimensions
107.19*59.93*25.64mm
Net weight
54g
Mouse introduction
① Mouse left key ② Mouse middle key(roller) ③ Mouse right key
④ DPI key ⑤ 2.4G USB receiver ⑥ Power button
⑦ Mode button ⑧ Battery slot ⑨ 2.4G USB receiver slot
⑩ Power indicator(red)
⑪ Bluetooth pairing indicator(blue)
⑫ 2.4GHz pairing indicator(red)
Bluetooth mode pairing steps
1.Insert 2 AAA batteries into the battery slot.
2.Turn on mouse:Slide power button to “ON”position,power indicator turns red.
3.Change to Bluetooth mode: Slide mode button to side,bluetooth indicator
flashes blue 2 seconds,then off.
4.Enter bluetooth pairing mode: Press both middle and right keys together,indicator
flashes blue.
5.Finish pairing:Turn on your device’s bluetooth function,device searches the mouse
⑥
⑦
⑧
⑨
⑩
⑪
⑫
pairing name”NW-MD156” automatically.Click pairing name,pairing
successfully,bluetooth indicator turns off.
2.4GHz mode pairing steps
1.Insert 2 AAA batteries into the battery slot.
2.Turn on mouse:Slide power button to “ON”position,power indicator turns red.
3.Change to 2.4GHz mode: Slide mode button to side,2.4G indicator flashes red
2 seconds,then off.
4.Enter 2.G pairing mode: Press both middle and right keys together,indicator flashes
red.
5.Finish pairing: Plug 2.4G USB receiver into device’s USB port,pairing
successfully,2.4G indicator turns off.
Note:
1.If the USB receiver and mouse have been paired successfully.Just need to plug
receiver into device’s USB port,they will paired successfully.No need to press both
middle and right keys.
2.2.4G USB receiver is only can be used for 2.4G connection,can not be used for
bluetooth connection.
DPI level adjust
Press “DPI” key to adjust mouse operating sensitivity level,800→1000→1200→1600.
800 DPI: Every mouse operating,it transmits 800 times of command control to device.
1000 DPI:Every mouse operating,it transmits 1000 times of command control to device.
1200 DPI:Every mouse operating,it transmits 1200 times of command control to device.
1600 DPI:Every mouse operating,it transmits 1600 times of command control to device.
Energy saving mode
If no using the mouse for 30 minutes,it will enter energy saving mode,press any key
to active.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.