Hangzhou Gubei Electronics Technology BL3329-P BL3329-P User Manual 1
Hangzhou Gubei Electronics Technology Co.,Ltd BL3329-P 1
User manual_1
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3629098 |
| Application ID | 8YpFxdxf+Lk2EFkhLNwmvQ== |
| Document Description | User manual_1 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 65.59kB (819919 bits) |
| Date Submitted | 2017-11-05 00:00:00 |
| Date Available | 2017-11-06 00:00:00 |
| Creation Date | 2017-10-12 11:18:42 |
| Document Lastmod | 2017-11-06 09:52:22 |
| Document Title | User manual_1 |
| Document Creator | WPS Office |
| Document Author: | Shu Fen |
BiTrend™ EssentialSeriesWi-Fi Module Datasheet BL3329-P Hangzhou Gubei Electronics Technology Co., Ltd. Copyright Information The information contained in this document is the proprietary information of Hangzhou Gubei Electronics Technology Co., Ltd. (hereinafter referred as BroadLink). Further, no portion of this document may be altered or edited in any form or by any meanswithout the prior written consent of BroadLink, the copyrightholder. Further BroadLink reserves the right to make modifications, additions anddeletions to this document due to typographical errors, inaccurate information, orimprovements to products mentioned in the document at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this document or published as errata sheet. Version History V 1.0.0 10/10/2017 1stissue of preliminary document 1www.ibroadlink.com Table of Contents 1. Introduction................................................................................................................................... 3 1.1 Overview.............................................................................................................................. 3 1.2 Applications.........................................................................................................................4 1.3 Key Features........................................................................................................................ 4 2. Product Overview......................................................................................................................... 5 2.1 Product Picture....................................................................................................................5 2.2 Block Diagram.....................................................................................................................6 3. Electrical Characteristics...............................................................................................................6 3.1 Absolute Maximum Ratings – Voltage & Current......................................................... 6 3.2Current consumption.......................................................................................................... 7 3.3 Absolute maximum ratings – Temperature.................................................................... 7 3.4Absolute maximum ratings – ESD.....................................................................................7 4. RF Characteristics..........................................................................................................................7 4.1Basic Characteristics............................................................................................................ 7 4.2 IEEE802.11b Mode..............................................................................................................8 4.3 IEEE802.11g Mode..............................................................................................................8 4.4 IEEE802.11n 20Mhz Bandwidth Mode.............................................................................9 5. Mechanical Characteristics........................................................................................................ 10 6. Module Interfaces.......................................................................................................................10 6.1 PIN Layout......................................................................................................................... 10 6.2 PIN Definitions.................................................................................................................. 11 7. Reference Design........................................................................................................................ 12 8.1 Antenna Selection............................................................................................................ 13 8.2 Minimizing Radio Interference....................................................................................... 14 8.3 Specification of On-Board Antenna...............................................................................14 Appendix A Glossary（Quentin respible）.................................................................................15 Appendix B Reference paper（Quentin respible）................................................................... 17 Contact Us........................................................................................................................................17 2www.ibroadlink.com 1. Introduction 1.1 Overview BiTrend™ Essentialis the industrial leading 2.4Ghz 802.11 b/g/n embedded Wi-Fi module which delivers unmatched performance and codeless development in a compact package, providing a quick, easy and cost effective way for developers and manufacturers to add Wi-Fi connectivity for home automation, lighting control, energy efficiency and other IOT applications. BiTrend ™ Essential family combines a 2.4Ghz 802.11 b/g/n radio transceiver with a 32-bit microprocessor and embedded with MAC, baseband processing and optimized Wi-Fi network stack. It is an ideal solution for developers and manufacturers with limited RF and embedded programming expertise as it significantly reduces RF design time and removes the burden of testing and certification. Benefitted from BroadLink’s turn-key solution, BiTrend™ Essential is an ideal solution for developers with limited Wi-Fi or RF expertise or for those seeking faster time to market. It reduces RF design time and removes the burden of testing and certification. BiTrend™ Essential is fully compliant with IEEE 802.11 b/g/n standard and certified with CE, FCC and RoHS. BiTrend™ Essential is a highly integrated Wi-Fi SoC(system on Chip) single chip, which supportsIEEE802.11b/g/n single stream, providing GPIO for intelligent control, and UART interfaces for device communication. BiTrend™ Essential has 8Mbits flash and integrates power amplifier, low noise amplifier, and RF switch to reduce the module size and RF design capability required. And also integrate power manage unit for single 3.3V power source for cost effective design. BiTrend™ Essential embedded 32-bit RISC MCU for 802.11b/g/n drivers, supplicant, TCP/IP protocol stack, and networking applications, can be operated in station mode and softAP mode. The 3329-P is an ideal solution for embedded device to enable networking service with minimized design effort. Figure 1. 3329-P block diagram 3www.ibroadlink.com 1.2 Applications Smart home appliances Remote Control Medical/Health Care Network consumer devices 1.3 Key Features a． Support IEEE802.11b/g/n Frequency Range 2.412 GHz - 2.462 GHz Wi-Fi Standard IEEE 802.11 b/g/n Transmitter Power 802.11b:17.5dBm 802.11g:14dBm 802.11n:14dBm MIN Receiver Sensitivity 802.11b<-81dBm@11Mbps 802.11g<-69dBm@54Mbps 802.11n<-68dBm@MCS7 Data rate 11M@802.11b, 54M@802.11g, MCS7@802.11n Security Encryption Standard：WEP/WEPA/WPA2 EncryptionAlgorithm：WEP64/WEP128/TKIP/AES Wi-Fi Modes STA/AP/STA+AP/WIFI Direct b． Support UART\PWM\ADC\GPIO\I2C port c． Support STA\AP\AP+STA d． Patent Smart Config™ technology e． Support TLS\SSL\mDNS f． PCB printed antenna Antenna type PCB printed ANT g． Power source: 3.3V h． Dimension （L*W*H) : 25mm*17.7mm*3.7mm (Including shielding cover height) i． ESD: 2KV 4www.ibroadlink.com 2. Product Overview 2.1 Product Picture 5www.ibroadlink.com 2.2 Block Diagram 3. Electrical Characteristics 3.1 Absolute Maximum Ratings – Voltage & Current Using products above the absolute maximum ratings may cause permanent damage to the device. These are maximum ratings only and functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may aff ect the reliability of the device. Symbol Description Min. Max. Units Ts Storage temperature -40 125 ℃ TAMBIENT Ambient Temperature -10 80 ℃ Vdd Supply voltage 3.0 3.6 Vio Voltage on IO pin 3.3 VESD HBM(human body model) 2000 6www.ibroadlink.com 3.2Current consumption Performance Symbol Condition IRF_Standby(SP mini) IDLE mode TYP Unit 80 mA IRF_b pulse current @TX 11b @18dBm 11Mbps 272 mA IRF_g pulse current @TX 11g @16dBm 54Mbps 247 mA IRF_n pulse current @TX 11n @15dBm MCS7 240 mA Note: All result is measured at the antenna port and VDD33 is 3.3V 3.3 Absolute maximum ratings – Temperature Rati Symbol Max Unit TSTG ngs Storagetemperature –40 to+125 ℃ TA Workingtemperature -10 to+80 ℃ Humidity Non condensing, relative humidity 90%（RH） 3.4Absolute maximum ratings – ESD Symbol VESD (HBM) Ratings Conditions Electrostatic discharge TA = +25 °C voltage conforming to (human body model) JESD22-A114 Class Max Unit 2000 4. RF Characteristics 4.1Basic Characteristics Item Specification OperatingFrequency 2.412 GHz - 2.462GHz Wi-FiStandard IEEE 802.11b/g/n 7www.ibroadlink.com 11b: DBPSK, DQPSK,CCK for DSSS ModulationType 11g: BPSK, QPSK, 16QAM, 64QAM for OFDM 11n: MCS0~7,OFDM 11b:1,2,5.5and 11Mbps Data Rates 11g:6,9,12,18,24,36,48 and 54 Mbps 11n:MCS0~MCS7 Antennatype PCB printed ANT 4.2 IEEE802.11b Mode Item Specification ModulationType DSSS/CCK Frequencyrange 2412MHz~2462MHz Channel CH1 toCH11 Datarate 1,2,5.5,11Mbps TX Characteristics Min Typical Max. Unit Transmitter Output Power 18 @11Mbps dBm -10 Frequency Error +10 ppm Constellation Error( peak EVM)@ target power -30 @11Mbps Transmit spectrum mask Pass RX Characteristics Min Typical Max. Unit -84 -83 dBm Minimum Input Level Sensitivity 11Mbps (FER≦8%) Maximum Input Level (FER≦8%) -10 dBm 4.3 IEEE802.11g Mode Item ModulationType Specification OFDM 8www.ibroadlink.com Frequencyrange 2412MHz~2462MHz Channel CH1 toCH11 Datarate 6,9,12,18,24,36,48,54Mbps TX Characteristics Min Typical Max. Unit Transmitter Output Power 14 @54Mbps -10 Frequency Error dBm +10 ppm -30 dB Max. Unit Constellation Error( peak EVM)@ target power @54Mbps Transmit spectrum mask Pass RX Characteristics Min Typical Minimum Input Level Sensitivity Maximum Input Level (FER≦10%) dBm -70 @54Mbps -20 dBm 4.4 IEEE802.11n 20Mhz Bandwidth Mode Item Specification ModulationType OFDM Frequencyrange 2412MHz~2462MHz Channel CH1 toCH11 Datarate MCS0/1/2/3/4/5/6/7 TX Characteristics Min Typical Max. Unit Transmitter Output Power Frequency Error dBm 14 @HT20, MCS7 -10 +10 ppm -30 dB Constellation Error( peak EVM)@ target power @HT20, MCS7 Transmit spectrum mask Pass 9www.ibroadlink.com RX Characteristics Min Typical Max. Unit -70 -68 dBm Minimum Input Level Sensitivity @HT20, MCS7 Maximum Input Level (FER≦10%) -20 dBm 5. Mechanical Characteristics Figure2. 3329-P top view(Metricunits) 6. Module Interfaces 6.1 PIN Layout 3328-P has one group of pins2X7. The layout of PINs are shown in the figure below. 10www.ibroadlink.com Figure6. 3329-P Layout 6.2 PIN Definitions PIN Assignment PIN PIN NAME NOTE Pin1 GND Pin2 VCC 3.3V Pin3 RST_N Module software reset,Available at low level Pin4 Pin5 UART_TX0 UART Only for Passthrough GPIO15 I/O UART_RX0 UART Only for Passthrough GPIO18 I/O 11www.ibroadlink.com Pin6 Pin7 Pin8 TX1 UART Only for Passthrough GPIO1 I/O RX1 UART Only for Passthrough GPIO3 I/O RX1 UART Only for Passthrough GPIO3 Pin9 TX1 I/O GPIO1 I2S Port Pin10 GPIO25 I/O Pin11 GPIO27 I/O Pin12 GPIO21 I/O Pin13 VCC 3.3V Pin14 GND 7. Reference Design Peripheral MCU WIFI MODULE If the peripheral MCU uses power source of 5V,it needs to add a level switching circuit in the connection of the serial port and the related circuit. The module needs a large current about 300mA when transmitting data,please ensure that the power source can provide sufficient current. 12www.ibroadlink.com 8. AntennaCharacteristics 8.1 Antenna Selection The WT1SBSL supports on-board PCB printed antenna.When the Operating Frequencyis between 2.4G~2.5GHz, S11 of antenna port is less than-10dB and peak gainis about 1. 2dBi. Figure 7. Antenna radiation pattern simulation Figure 8. Antenna port S11simulation curve In practical use, 3329-P is welded on user’s boardand value of S11 has some changes. 13www.ibroadlink.com 8.2 Minimizing Radio Interference When integrating the Wi-Fi module with on board PCB printed antenna, make sure the three points below: 1. The area under the antenna end of the module should be keep clear of metallic components, connectors, vias, traces and other materials that can interfere with the radio signal. 2. The area around the antenna end the module protrudes at least 10mm from the mother board PCB and any metal enclosure. 3. When planning PCB layout, it is recommended that user places the antenna of Wi-Fi module as close as possible to the edge of boarder to ensure the good performance of antenna, which is shown in the picture below. 8.3 Specification of On-Board Antenna OperatingFrequency 2.4G~2.5GHz VSWR(max) Peak Gain 1.2dBi AntennaType PIFA 14www.ibroadlink.com Appendix A Glossary（Quentin respible） ADC AES ANT AP BPSK Analog-to -Digital Converter Advanced Encryption Standard Antenna Wireless Access Point Binary Phase Shift Keying CCK CDM Complementary Code Keying Charge Device Model DBPSK DC Differential binary phase shift keying Direct Current DHCP Dynamic Host Configuration Protocol CMOS Complementary Metal Oxide Semiconductor DNS DQPSK DSSS DTIM EMSP ESD EVM FCC FER GND GPIO HBM IEEE IO IOT IPv4 LED LVTTL MAC MCS MCU MIMO MSL NC NRST OFDM OSC PCB PIFA QPSK Determination of non-significance Differential quadrature phase shift keying Demand assigned signaling and switching subsystem Digital Transmission Interface Module Enhanced Modular Signal Processor Electrostatic Discharge Error Vector Magnitude Federal Communications Commission Floating Error Ground General Purpose Input/Output Human body model Institute of Electrical and Electrionics Engineers Input/Output Individual operation test Internet Protocol version 4 Light-emitting diode Low Voltage Transistor Transistor Logic Medium Access Control layer Modulation and coding scheme Microcontroller Unit Multiple-Input Multiple-Output Multilayer Switching Protocol Numerical Control Negative Reset Orthogonal Frequency Division Multiplexing Oscillator Printed Circuit Board Planar inverted F antenna Quadrature Phase Shift Keyin 15www.ibroadlink.com RC RF RISC RoHS RX SDIO SoC SPDT SPI STA TCP TKIP TX IP UART UDP UFL VSWR WEP WEPA WEP64 WEP128 WPA2 XTAL QAM 802.11 b/g/n Resistance- capacitance Radio Frequency Reduced Instruction Set Computer Restriction of Hazardous Substances Receiver Serial Digital Input/Output System on Chip Single-Pole Double-Throw Serial Peripheral Interface Spanning Tree Algorithm Transfer Control Protocol Temporal Key Integrity Protocol Transmitter Internet Protocol Universal Asynchronous Receiver/Transmitter User Datagram Protocol a miniature coaxial RF connector for high-frequency signals manufactured by Hirose Electric Group Voltage Standing Wave Ratio Wired Equivalent Privacy Welded Electronic Packaging Association 64 bit Wired Equivalent Privacy 128 bit Wired Equivalent Privacy Wi-Fi Protected Access 2 External Crystal Oscillator Quadrature Amplitude Modulation The IEEE 802.11 b/g/n 16www.ibroadlink.com Appendix B Reference paper（Quentin respible） [1] IEEE 802.11b/g/n- published IEEE 802.11-2007wireless networking standard and published IEEE 802.11-2012 standard for Information technology - Clause 19 of the publishedIEEE 802.11-2007 standard, and Clause 19 of the published IEEE 802.11-2012 standard. Contact Us Hangzhou Gubei Electronics Technology Co., Ltd. Room 106, Building 1, No. 611 Jianghong Road, Binjiang, Hangzhou, Zhejiang, P.R.China T: +86-571-85159281 F: +86-571-86631817 E: intl@broadlink.com.cn W: www.ibroadlink.com.cn This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 17www.ibroadlink.com Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. MPE Requirements To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement. Region Selection Limited by local law regulations, version for North America does not have region selection option. Information for the OEM Integrators This device is intended for OEM integrators only. Please see the full grant of equipment document for restrictions. Label Information to the End User by the OEM or Integrators 18www.ibroadlink.com If the FCC ID of this module is not visible when it is installed inside another device, then the outside of the device into which the module is installed must be label with “Contains FCC ID: XXXXXXX and IC: XXXXXXXX” 19www.ibroadlink.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : Shu Fen Description : Title : Comments : Company : Source Modified : D:20171012111843+03'18' Create Date : 2017:10:12 11:18:42+03:00 Creator Tool : WPS Office Modify Date : 2017:11:06 09:52:22+08:00 Metadata Date : 2017:11:06 09:52:22+08:00 Keywords : Producer : Document ID : uuid:016e5997-332e-46a4-aae9-2815e31582c0 Instance ID : uuid:75e085b7-11d0-437d-8e84-603342ec59d5 Page Count : 20 Author : Shu Fen Subject : Trapped : falseEXIF Metadata provided by EXIF.tools