Hangzhou H3C Technologies H3CEWT0235A29F Wireless LAN Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	969750
Application ID	Mtt6qfaibsWB/xohJQwBiA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	120.86kB (1510804 bits)
Date Submitted	2008-07-14 00:00:00
Date Available	2008-07-18 00:00:00
Creation Date	2008-07-10 01:53:52
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2008-07-10 12:04:14
Document Title	user manual

H3C WA2200 Series WLAN Access Points
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version:
Copyright © 2006-2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C,
, Aolynk,
, H3Care,
, TOP G,
, IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
customer_service@h3c.com
http://www. h3c.com
About This Manual
Related Documentation
In addition to this manual, each H3C WA2200 Series WLAN Access Points
documentation set includes the following:
Manual
Description
H3C WA2200 Series WLAN Access Points
Operation Manual
Guides the user to configure features
supported by the WA2200 series.
H3C WA2200 Series WLAN Access Points
Command Manual
Elaborates on the commands for configuring
the WA2200 series.
Organization
The H3C WA2200 Series WLAN Access Points Installation Manual is organized as
follows:
Chapter
Contents
1 Product Overview
Introduces the hardware configuration, appearances, and
interfaces of the WA2200 series.
2 Installation Preparations
Introduces the environment requirements, precautions, and
tools for the installation of the WA2200 series.
3 Installation of Indoor APs
Introduces the mechanical installation, power supply
connection, and Ethernet cable connection of the indoor
APs and enhanced APs.
4 Installation of Outdoor APs
Introduces the outdoor installation checklist, installation
flowchart, antenna installation, cable connection, and
network connection of outdoor APs.
5 Software Setting
Introduces the software maintenance (including working
mode switching, software debugging environment setup,
security setting, and system name and system clock setting)
of the WA2200 series.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention
Description
Boldface
The keywords of a command line are in Boldface.
italic
Command arguments are in italic.
[]
Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
&<1-n>
The argument(s) before the ampersand (&) sign can be
entered 1 to n times.
A line starting with the # sign is comments.
II. GUI conventions
Convention
Description
<>
Button names are inside angle brackets. For example, click
.
[]
Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
III. Symbols
Convention
Description
Warning
Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution
Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note
Means a complementary description.
Environmental Protection
This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.
Installation Manual
H3C WA2200 Series WLAN Access Points
Table of Contents
Table of Contents
Chapter 1 Product Overview ........................................................................................................ 1-1
1.1 Introduction ........................................................................................................................ 1-1
1.2 Hardware Configuration..................................................................................................... 1-2
1.2.1 LEDs........................................................................................................................ 1-3
1.2.2 Interfaces................................................................................................................. 1-7
Chapter 2 Installation Preparations............................................................................................. 2-1
2.1 Unpacking and Inspection ................................................................................................. 2-1
2.2 Preparing Installation Tools ............................................................................................... 2-2
2.3 Examining the Installation Site........................................................................................... 2-2
2.3.1 Installation Site Selection ........................................................................................ 2-2
2.3.2 Temperature and Humidity Requirements .............................................................. 2-3
2.3.3 Power Supply .......................................................................................................... 2-3
2.3.4 Grounding and Lightning Protection ....................................................................... 2-4
Chapter 3 Installation of Indoor APs ........................................................................................... 3-1
3.1 Installation Flowchart ......................................................................................................... 3-1
3.2 Determining the Installation Position ................................................................................. 3-1
3.3 Installing the AP ................................................................................................................. 3-2
3.3.1 Installing the Wall-Mounting Bracket on a Wall....................................................... 3-2
3.3.2 Installing the AP on the Wall-Mounting Bracket...................................................... 3-3
3.3.3 Locking the AP onto the Wall-Mounting Bracket (Optional).................................... 3-4
3.4 Connecting the Power Supply ........................................................................................... 3-6
3.4.1 Local Power Supply ................................................................................................ 3-6
3.4.2 Power over Ethernet ............................................................................................... 3-7
3.5 Connecting the Network .................................................................................................... 3-8
Chapter 4 Installation of Outdoor APs ........................................................................................ 4-1
4.1 Installation Flowchart ......................................................................................................... 4-1
4.1.1 Installing the AP ...................................................................................................... 4-1
4.1.2 Installing an Outdoor Antenna................................................................................. 4-7
4.1.3 Connecting External Cables.................................................................................. 4-12
4.1.4 Powering On the AP.............................................................................................. 4-19
4.2 Connecting the Network .................................................................................................. 4-21
Chapter 5 Software Setting .......................................................................................................... 5-1
5.1 Working Mode Switching ................................................................................................... 5-1
5.1.1 Identifying the Current Working Mode .................................................................... 5-1
5.1.2 Switching from the FAT Mode to the FIT Mode ...................................................... 5-2
5.1.3 Switching from the FIT Mode to the FAT Mode ...................................................... 5-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Table of Contents
5.2 Setting Up a Software Debugging Environment ................................................................ 5-2
5.2.1 Setting Up a Connection with the AP Through the Console Interface .................... 5-2
5.2.2 Telneting to the AP.................................................................................................. 5-2
5.2.3 Configuring Telnet................................................................................................... 5-2
5.3 Configuring a FIT AP ......................................................................................................... 5-2
5.3.1 Associating a FIT AP with the AC ........................................................................... 5-2
5.3.2 Configuring a FIT AP on the AC.............................................................................. 5-2
5.3.3 Security Setting ....................................................................................................... 5-2
5.4 Configuring a FAT AP........................................................................................................ 5-2
5.4.1 System Setting ........................................................................................................ 5-2
5.4.2 Setting a System Name and the System Clock ...................................................... 5-2
5.4.3 Security Setting ....................................................................................................... 5-2
ii
Installation Manual
H3C WA2200 Series WLAN Access Points
List of Figures
List of Figures
Figure 1-1 Positions of the WA2200 series on the network................................................... 1-1
Figure 1-2 Appearance of the WA2200 series ....................................................................... 1-2
Figure 1-3 LEDs on the H3C WA2210-AG/WA2220-AG ....................................................... 1-3
Figure 1-4 LEDs on the H3C WA2220E-AG .......................................................................... 1-5
Figure 1-5 LEDs on the H3C WA2210X-G ............................................................................ 1-6
Figure 1-6 LEDs on the WA2220X-AG and WA2220X-AGP ................................................. 1-6
Figure 1-7 Interfaces on H3C WA2210-AG/WA2220-AG(indoor)........................................ 1-10
Figure 1-8 Interfaces on H3C WA2220E-AG(enhanced)..................................................... 1-11
Figure 1-9 Interfaces on H3C WA2210X-G/WA2220X-AG/WA2220X-AGP(outdoor) ......... 1-11
Figure 3-1 Installation flowchart of an indoor (enhanced) AP ................................................ 3-1
Figure 3-2 Screw hole locations and screw hole size............................................................ 3-2
Figure 3-3 Install the wall-mounting bracket .......................................................................... 3-3
Figure 3-4 Fix the indoor AP onto the wall-mounting bracket ................................................ 3-4
Figure 3-5 Fix the enhanced AP onto the wall-mounting bracket .......................................... 3-4
Figure 3-6 Lock the indoor AP onto the wall-mounting bracket ............................................. 3-5
Figure 3-7 Lock the enhanced AP onto the wall-mounting bracket ....................................... 3-6
Figure 3-8 Local power supply connection ............................................................................ 3-7
Figure 3-9 PoE connection .................................................................................................... 3-7
Figure 3-10 Connect the AP to the network ........................................................................... 3-8
Figure 4-1 Installation flowchart of the outdoor models ......................................................... 4-1
Figure 4-2 Installation flowchart of the AP on a wall .............................................................. 4-2
Figure 4-3 Wall-mounting bracket structure and positions of screw holes ............................ 4-3
Figure 4-4 Install the outdoor AP on a wall ............................................................................ 4-5
Figure 4-5 Pole and pole base............................................................................................... 4-6
Figure 4-6 Install the outdoor AP on a vertical pole ............................................................... 4-6
Figure 4-7 Install the outdoor AP on a horizontal pole ........................................................... 4-7
Figure 4-8 Install a directional outdoor antenna on a parapet ............................................... 4-8
Figure 4-9 Install a directional outdoor antenna on a building top surface or cement pier.............. 4-8
Figure 4-10 Install omni antennas........................................................................................ 4-10
Figure 4-11 Install an omni antenna under a special environment ...................................... 4-11
iii
Installation Manual
H3C WA2200 Series WLAN Access Points
List of Figures
Figure 4-12 Install an omni antenna on the AP directly ....................................................... 4-12
Figure 4-13 Connect the Ethernet electrical interface to the uplink device ......................... 4-14
Figure 4-14 Connect the Ethernet optical interface to the uplink device ............................. 4-14
Figure 4-15 Exploded view of the port lightning protector (PoE) ......................................... 4-15
Figure 4-16 Ethernet cable connector.................................................................................. 4-16
Figure 4-17 Insert the Ethernet cable connector into the Ethernet interface ....................... 4-18
Figure 4-18 Connect a fiber cable........................................................................................ 4-18
Figure 4-19 Connection of external cables of the AP .......................................................... 4-20
Figure 4-20 Connection between the AP and Internet......................................................... 4-21
Figure 5-1 Connection between a FIT AP and the AC........................................................... 5-2
iv
Installation Manual
H3C WA2200 Series WLAN Access Points
List of Tables
List of Tables
Table 1-1 Physical dimensions of the WA2200 series ........................................................... 1-2
Table 1-2 Protocols that each model supports and the chassis material ............................... 1-2
Table 1-3 Description of LEDs on the H3C WA2210-AG/WA2220-AG .................................. 1-4
Table 1-4 Description of LEDs on the H3C WA2220E-AG..................................................... 1-5
Table 1-5 Description of LEDs on the H3C WA2210X-G, WA2220X-AG, and WA2220X-AGP
......................................................................................................................................... 1-7
Table 1-6 Descriptions of interfaces on WA2200 series WLAN access points ...................... 1-8
Table 2-1 List of articles in the package ................................................................................. 2-1
Table 2-2 List of installation tools ........................................................................................... 2-2
Table 2-3 Environment specifications..................................................................................... 2-3
Table 2-4 Nominal voltage and frequency of the low-voltage AC power supply .................... 2-3
Table 2-5 Grounding and lightning protection requirements .................................................. 2-4
Table 4-1 RJ-45 straight-through Ethernet cable pinouts..................................................... 4-16
Table 4-2 RJ-45 crossover Ethernet cable pinouts .............................................................. 4-17
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
Chapter 1 Product Overview
1.1 Introduction
The H3C WA2200 series WLAN access points (hereinafter referred to as the WA2200
series) are developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to
as H3C). The WA2200 series consist of six models of access points (APs), which fall
into three types according to the application environment: indoor, enhanced, and
outdoor. The WA2200 series can serve as FIT APs to cooperate with wireless switches
or controllers or serve as FAT APs to provide wireless access for WLAN users.
Figure 1-1 shows the typical deployment of the WA2200 series on hotspots.
PC
WA2200
Auditorium
Switch
PC
PC
WA2200
WA2200
Restaurant or
tea house
Switch
Core equipment
room
Switch
Parking lot
Switch
PC
WA2200
Hall or information
desk
Switch
Figure 1-1 Positions of the WA2200 series on the network
Figure 1-2 shows the appearance of the WA2200 series.
1-1
Radius server
Wireless NMS
Service database
server
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
Figure 1-2 Appearance of the WA2200 series
Table 1-1 Physical dimensions of the WA2200 series
Model
Physical dimensions (H×W×D)
H3C WA2210-AG/WA2220-AG, (indoor)
40×166×118 mm (1.57×6.54×4.65 in.)
H3C WA2220E-AG, (enhanced)
35×195×135 mm (1.38×7.68×5.31 in.)
H3C
WA2210X-G/WA2220X-AG/WA2220X-A
GP, (outdoor)
76×245×245 mm (2.99×9.65×9.65 in.)
1.2 Hardware Configuration
The six models of the WA2200 series have different radio frequencies (RFs) and
structures. Table 1-2 lists the protocols that each model supports as well as the chassis
materials.
Table 1-2 Protocols that each model supports and the chassis material
Type
Indoor
Model
Protocols and chassis material
H3C
WA2210-AG
IEEE802.11a or IEEE802.11b/g, plastic
H3C
WA2220-AG
IEEE802.11a + IEEE802.11b/g, plastic
1-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Type
Enhanced
Outdoor
Chapter 1 Product Overview
Model
Protocols and chassis material
H3C
WA2220E-AG
IEEE802.11a + IEEE802.11b/g, sheet metal
H3C
WA2210X-G
IEEE802.11b/g, waterproof cast aluminum +
plastic
H3C
WA2220X-AG
IEEE802.11a + IEEE802.11b/g, waterproof cast
aluminum + plastic
H3C
WA2220X-AGP
IEEE802.11a + IEEE802.11b/g, waterproof cast
aluminum + plastic
The WA2200 series have extraordinary radio frequency (RF) performance and provide
consummate service functions. With IP65 degree of protection, the outdoor models can
be directly deployed outdoors to simplify the installation. The models of the WA2200
series are designed for application in various environments.
This section describes the hardware configurations and functions of the WA2200 series
in detail.
1.2.1 LEDs
The positions and identifications of LEDs on the panel vary with the models. For details
about these LEDs, see Table 1-3, Table 1-4, and Table 1-5.
I. H3C WA2210-AG/WA2220-AG
Figure 1-3 LEDs on the H3C WA2210-AG/WA2220-AG
1-3
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
Table 1-3 Description of LEDs on the H3C WA2210-AG/WA2220-AG
LED
Color
QTY
Meaning
Displays the power supply status:
POWER
Green
On: The power supply is normal.
Off/flashing: The power supply is not
connected or well connected, or works
abnormally.
Displays the link status of the Ethernet
interface:
LINK/ACT
Green
On: The link on the Ethernet interface is up.
Off: The link on the Ethernet interface is
down.
Flashing: Data is being transmitted or
received.
Displays the wireless link status:
11a
Green
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A wireless station is
accessing the device.
Flashing quickly: Data is being transmitted
or received.
Displays the wireless link status:
11b/g
Green
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A wireless station is
accessing the device.
Flashing quickly: Data is being transmitted
or received.
Caution:
The WA2210-AG is a single-RF device. The 11a and 11b/g LEDs cannot be on or flash
at the same time.
1-4
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
II. H3C WA2220E-AG
Figure 1-4 LEDs on the H3C WA2220E-AG
Table 1-4 Description of LEDs on the H3C WA2220E-AG
LED
Color
QTY
Meaning
Displays the power supply status:
POWER
Green
On: The power supply is normal..
Off/flashing: The power supply is not
connected or well connected or the AP
works abnormally.
Displays the wireless link status:
11b/g
Green
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A station is accessing the
device.
Flashing quickly: Data is being transmitted
or received.
Displays the wireless link status:
11a
Green
1-5
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A station is accessing the
device.
Flashing quickly: Data is being transmitted
or received.
Installation Manual
H3C WA2200 Series WLAN Access Points
LED
Chapter 1 Product Overview
Color
QTY
Meaning
Displays the speed of the Ethernet interface:
SPEED
Yellow
On: The Ethernet interface operates at 100
Mbps.
Off: The Ethernet interface operates at 10
Mbps.
Displays the connection status of the Ethernet
interface:
LINK/ACT
Green
On: The link on the Ethernet interface is up.
Off: The link on the Ethernet interface is
down.
Flashing: Data is being transmitted or
received.
III. H3C WA2210X-G, WA2220X-AG, and WA2220X-AGP
Figure 1-5 LEDs on the H3C WA2210X-G
Figure 1-6 LEDs on the WA2220X-AG and WA2220X-AGP
1-6
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
Table 1-5 Description of LEDs on the H3C WA2210X-G, WA2220X-AG, and
WA2220X-AGP
LED
Color
QTY
Meaning
Displays the power supply status:
POWER
Green
On: The power supply is normal..
Off/flashing: The power supply is not
connected or well connected or the device
works abnormally.
Displays the status of the Ethernet interface:
10/100BASE
-TX
Green
On: The link on the Ethernet interface is up.
Off: The link on the Ethernet interface is
down.
Flashing: Data is being transmitted or
received.
Displays the status of the optical interface:
100BASE-F
Yellow
On: The link on the optical interface is up.
Off: The link on the optical interface is down.
Flashing: Data is being transmitted or
received.
Displays the wireless link status:
11a
Green
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A station is accessing the
device.
Flashing quickly: Data is being transmitted
or received.
Displays the wireless link status:
11b/g
Green
On: The wireless link is normal.
Off: The wireless link is not initialized or the
link is faulty.
Flashing slowly: A station is accessing the
device.
Flashing quickly: Data is being transmitted
or received.
Note:
The WA2210X-G is a single-RF device and has no 11a LED.
The word “reserved” means the LED is reserved for future use.
1.2.2 Interfaces
The interfaces provided by the WA2200 series include:
1-7
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
2.4 GHz or/and 5 GHz antenna interface(s)
Console interface
Ethernet interface (optical and electrical)
Power interface for indoor and enhanced models
Note:
In addition, the indoor and enhanced models have a reset button, a security slot, a
grounding screw.
Table 1-6 describes the interfaces provided by each model.
Table 1-6 Descriptions of interfaces on WA2200 series WLAN access points
Model
WA2210-A
G/WA2220AG
Interface
Standards and
protocols
Antenna
interface 1
IEEE802.11b/g
Console
interface
RS/EIA-232
Ethernet
interface
Power
interface
Antenna
interface 2
IEEE802.3
IEEE802.3u
IEEE802.3af
Description
WA2210-AG: Main antenna
interface, 2.4/5-GHz
WA2220-AG: 2.4-GHz antenna
interface
The console interface is used for
device configuration and
management.
The Ethernet interface can serve
as an uplink interface of the device
to access the Internet or a MAN,
and can simultaneously serve as a
PoE interface.
The power interface is used for
+48 VDC power supply to the
device.
N/A
IEEE802.11a
1-8
WA2210-AG: Auxiliary antenna
interface, 2.4/5-GHz
WA2220-AG: 5-GHz antenna
interface
Installation Manual
H3C WA2200 Series WLAN Access Points
Model
WA2220EAG
WA2210XG/WA2220
X-AG/WA2
220X-AGP
Interface
Chapter 1 Product Overview
Standards and
protocols
Description
Antenna
interface 2
IEEE802.11a
This antenna interface is used to
connect a 5-GHz antenna or a
feeder.
Console
interface
RS/EIA-232
The console interface is used for
device configuration and
management
Ethernet
interface
IEEE802.3
IEEE802.3u
IEEE802.3af
The Ethernet interface can serve
as an uplink interface of the AP to
access Internet or MAN, and can
simultaneously serve as a PoE
interface.
Power
interface
N/A
The power interface is used for
+48 VDC power supply to the
device.
Antenna
interface 1
IEEE802.11b/g
This antenna interface is used to
connect a 2.4-GHz antenna or a
feeder.
Ethernet
optical
interface
IEEE802.3
Ethernet
electrical
interface
IEEE802.3
SFP MSA
SFF-8472
IEEE802.3u
IEEE802.3af
The Ethernet optical interface can
serve as an uplink interface to
access the Internet or a MAN. The
Ethernet optical interface is used
to connect an SFP module. In
practice, either the Ethernet
electrical interface or the Ethernet
optical interface is used.
The Ethernet electrical interface
can serve as an uplink interface of
the device to access the Internet
or a MAN, and can simultaneously
serve as a PoE interface.
Antenna
interface 1
IEEE802.11b/g
This antenna interface is used to
connect a 2.4-GHz antenna or a
feeder.
Console
interface
RS/EIA-232
The console interface is used for
device configuration and
management.
Antenna
interface 2
IEEE802.11a
This antenna interface is used to
connect a 5-GHz antenna or a
feeder.
1-9
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
I. Interfaces provided by H3C WA2210-AG/WA2220-AG
Top view
Bottom view
Antenna interface 1
Antenna interface 2
Figure 1-7 Interfaces on H3C WA2210-AG/WA2220-AG
Caution:
H3C WA2210-AG is a single-RF device. Viewed from the front, the antenna
interface on the left (antenna interface 1 in Figure 1-7) is the main antenna interface,
while the one on the right (antenna interface 2 in Figure 1-7) is the auxiliary antenna
interface. When there is only one antenna, the antenna must be installed on the
main antenna interface.
H3C WA2220-AG is a dual-RF device. Viewed from the front, the antenna interface
on the left (antenna interface 1 in Figure 1-7) is the 2.4-GHz antenna interface, while
the one on the right (antenna interface 2 in Figure 1-7) is the 5-GHz antenna
interface.
1-10
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
II. Interfaces provided by H3C WA2220E-AG
Figure 1-8 Interfaces on H3C WA2220E-AG
III. Interfaces provided by H3C WA2210X-G/WA2220X-AG/WA2220X-AGP
Figure 1-9 Interfaces on H3C WA2210X-G/WA2220X-AG/WA2220X-AGP
1-11
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 1 Product Overview
Note:
H3C WA2210X-G is a single-RF device and provides no 5-GHz antenna interface.
1-12
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 2 Installation Preparations
Chapter 2 Installation Preparations
This chapter describes the preparations for WA2200 installation, including preparation
of installation tools, environment examination, and unpacking & inspection.
2.1 Unpacking and Inspection
Before unpacking the package, make sure that the package is intact, without any
serious damage or sign of water soaking. When unpacking the package, avoid
excessive force or collision. Otherwise, the articles inside the package may get
damaged.
After unpacking the package, make sure that the following articles are available in the
package:
Table 2-1 List of articles in the package
Description
QTY
WA2200 WLAN AP
1 PCS
Power adapter
1 PCS
220 VAC power cord
1 PCS
Console cable
1 PCS
Installation kit
1 PCS
Omni antenna
2 PCS
H3C WA2200 Series WLAN Access Points Installation Manual
1 PCS
H3C WA2200 Series WLAN Access Points Electronic
Documentation
1 PCS
Packing list
1 PCS
Note:
The accessories may vary with the models and are subject to the packing list.
If there is any inconsistency with the packing list, contact your local dealer in time.
If the package is rusted or water soaked, stop unpacking and contact your local
dealer timely.
2-1
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 2 Installation Preparations
2.2 Preparing Installation Tools
When installing the AP, you may need the tools listed in Table 2-2. You should select the
appropriate tools according to the installation environment.
Table 2-2 List of installation tools
Type of tool
Indoor installation
Outdoor installation
General
tools
1-meter-long ruler, marking pen,
knife, and percussion drill with
matching drills
Digging tool, adjustable
spanner, and vices
Special tools
Cable stripper, crimping pliers,
and RJ-45 crimping pliers
Cable stripper, crimping pliers,
RJ-45 crimping pliers,
waterproof tape, and fiber fusion
splicer
Auxiliary
tools
Ladder and rubber hammer
Ladder
Note:
Table 2-2 is only for reference. If you install the AP on a desk, none of the above tools is
required; if you install the AP on top of or under eave of a building, no digging tool is
required.
2.3 Examining the Installation Site
Before installation, you should examine the installation site to keep the AP under a
good operational environment. You can examine the installation site from the following
two aspects:
2.3.1 Installation Site Selection
Keep the AP away from places that are susceptible to high temperature, dust,
inflammable, explosive, electromagnetic interference (high power radar, radio station,
and transformer), unstable voltage, heavy vibration, or loud noise. The installation site
should be dry, without any leakage, dripping, or dew .The AP should be at least 500 m
(0.31 mi) away from the seaside and should not face the direction of sea wind.
In engineering design, the site should be selected according to the network planning
and technical requirements of communications equipment, as well as the
considerations such as climate, hydrology, geology, earthquake, electric power, and
transportation.
2-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 2 Installation Preparations
2.3.2 Temperature and Humidity Requirements
Table 2-3 lists the operating temperature and humidity requirements.
Table 2-3 Environment specifications
Specification
Range
Recommended
value
Test
condition
Operating
temperature (indoor)
0°C to 45°C (32°F to
113°F)
25°C (77°F)
None
Operating
temperature (outdoor)
–30°C to +55°C (–22°F
to +131°F)
25°C (77°F)
None
–20°C to +35°C (–4°F to
+95°F)
25°C (77°F)
No longer
than one
year
–20°C to +45°C (–22°F
to +113°F)
25°C (77°F)
No longer
than three
months
–20°C to +55°C (–22°F
to +131°F)
25°C (77°F)
No longer
than one
month
10% to 95%
—
None
Storage temperature
Relative humidity
(noncondensing)
2.3.3 Power Supply
Check that the site power supply is stable. The centralized AC power system consisting
of mains, UPS, and self-supplied diesel generator should be
Easy to connect
Safe to operate
Flexible to dispatch
Convenient to maintain
The low-voltage power supply should adopt the single-phase three-wire system. Table
2-4 lists the nominal voltage and frequency of the low-voltage AC power supply.
Table 2-4 Nominal voltage and frequency of the low-voltage AC power supply
Power supply
Single-phase three-wire
Nominal voltage
100 VAC to 240 VAC
2-3
Stable frequency
50 Hz/60 Hz
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 2 Installation Preparations
Caution:
If the voltage is unstable, a voltage regulator or stabilizer is required.
An uninterrupted power supply (UPS) is required for uninterrupted communication.
2.3.4 Grounding and Lightning Protection
Table 2-5 Grounding and lightning protection requirements
SN
Item
Requirements
The grounding resistance is usually required to be less
than 5 ohms, and less than 10 ohms in an area with less
than 20 thunderstorm days a year.
The top of the grounding body should be at least 0.7 m
(2.30 ft) away from the ground surface. In cold areas, the
grounding body should be buried below the frozen soil
layer.
Grounding
resistance
Grounding
lead-in
The grounding lead-in should be no longer than 30 m (98.43
ft). A zinc-coated flat steel with a cross-section area of 40 × 4
mm (1.57 × 0.16 in) or 50 × 5 mm (1.97 × 0.20 in) is
recommended.
AC power
grounding
The neutral line of the power cord should not be connected
with the PGND of other communications equipment.
Lightning
protection
Feeder
In plain areas, the protection angle of the lightning rod
should be less than 45 degrees. In mountainous areas or
lightning areas, the protection angle should be less than
30 degrees. The lightning protection grounding (for
example, the grounding of the lightning rod) should be
connected to the grounding body of the equipment room.
The AC power system in the equipment room should be
equipped with a lightning protection box. The grounding
cable for the lightning protection box should be greater
than 25 mm2 (0.039 in2) in area, and less than 30 m (98.42
ft) in length.
The antenna support is already prepared according to the
design requirements.
A feeder lightning rod is already installed and grounded
according to the design requirements.
After you have completed the preparations, you can start installing the AP. The
installation of indoor models (including the enhanced model) is different from that of the
outdoor models. For details, refer to Chapter 3 “Installation of Indoor APs” on page 3-1
and Chapter 4 “Installation of Outdoor APs” on page 4-1.
2-4
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
Chapter 3 Installation of Indoor APs
You can directly place an indoor model (including the enhanced model) on a desk. The
rubber feet on the bottom of the AP help you to place it horizontally. Or you can fix it
onto a wall by using the wall-mounting bracket. The indoor models and enhanced
model have the same wall-mounting brackets and accessories. The following
introduces the wall-mounting procedure of the indoor models and enhanced model in
detail.
3.1 Installation Flowchart
Figure 3-1 shows the installation flowchart of the indoor models and enhanced model.
Figure 3-1 Installation flowchart of an indoor (enhanced) AP
3.2 Determining the Installation Position
Determine the installation position by observing the following principles:
Leave as few obstacles (such as wall and ceiling) as possible between the AP and
stations.
Keep the AP far away from electronic devices (such as microwave oven) that may
generate RF noise.
Install the AP in a place where it will not hinder people’s daily work and life.
Note:
A padlock is required for ceiling mounting to prevent any falloff in case of shocks. A
Blossom 071 padlock or similar padlock is recommended.
3-1
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
3.3 Installing the AP
The following describes how to install the AP on a wall.
Installing the Wall-Mounting Bracket on a Wall
Installing the AP on the Wall-Mounting Bracket
Locking the AP onto the Wall-Mounting Bracket (Optional)
3.3.1 Installing the Wall-Mounting Bracket on a Wall
Follow these steps to install the wall-mounting bracket on a wall:
1)
Drill holes 6 mm (0.24 in) in diameter on the wall where the AP should be mounted.
The drilled holes should correspond to those in the wall-mounting bracket. There
are eight installation holes in total in the wall-mounting bracket. You should select
at least three in a triangle for installation.
Figure 3-2 Screw hole locations and screw hole size
2)
Insert the pointed end of anchors into the drilled holes and tap the flat end of
anchors with a rubber hammer until they are all flush with the wall surface.
3)
Align the holes in the wall-mounting bracket with the anchors and insert screws
through the installation holes into the anchors, as shown in Figure 3-3.
4)
Adjust the position of the wall-mounting bracket and tighten the screws.
3-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
Figure 3-3 Install the wall-mounting bracket
3.3.2 Installing the AP on the Wall-Mounting Bracket
Follow these steps to install the AP on the wall-mounting bracket:
1)
Align the AP with the hooks on the wall-mounting bracket and hang the AP on the
bracket (see (1) in Figure 3-4 and Figure 3-5).
2)
Then press the AP downward to fix it (see (2) in Figure 3-4 and Figure 3-5).
3-3
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
(1)
Expansion screw
(2)
Hock
Figure 3-4 Fix the indoor AP onto the wall-mounting bracket
Figure 3-5 Fix the enhanced AP onto the wall-mounting bracket
3.3.3 Locking the AP onto the Wall-Mounting Bracket (Optional)
The indoor and enhanced APs have a security slot on the top, which can be used to
lock the AP onto the wall-mounting bracket to prevent theft.
3-4
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
Follow these steps to lock the AP onto the wall-mounting bracket:
1)
Insert the locking plate into the security slot on the top of the AP (see (1) in Figure
3-6 and Figure 3-7).
2)
Turn the locking plate counterclockwise until the hole on the locking plate is
aligned with the hole in the wall-mounting bracket (see (2) in Figure 3-6 and Figure
3-7).
3)
Put the latch through the two holes that are aligned in step 2 (see (3) in Figure 3-6
and Figure 3-7).
4)
Lock the latch with a lock.
Figure 3-6 Lock the indoor AP onto the wall-mounting bracket
3-5
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
(1)
(2)
Locking plate
Latch
(3)
Locking hole
Wall-mounting bracket
Figure 3-7 Lock the enhanced AP onto the wall-mounting bracket
Note:
The lock is user supplied.
3.4 Connecting the Power Supply
3.4.1 Local Power Supply
Connect the AP to the power adapter and then to the power source, as shown in Figure
3-8.
3-6
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
Power interface
Power adapter
Figure 3-8 Local power supply connection
3.4.2 Power over Ethernet
If the uplink device of the AP is a PoE-capable switch or the like, use an Ethernet cable
to directly connect the Ethernet interface of the AP to the PoE-capable device.
Figure 3-9 PoE connection
Caution:
In the case of PoE, you do not need to connect the power interface to a power
source. You only need to connect one end of an Ethernet cable to the Ethernet
interface of the AP and the other end to an Ethernet interface of the PoE-capable
device (for example, Ethernet switch).
Identify the silkscreen on the device to avoid taking the console interface for the
Ethernet interface and vice versa.
3-7
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 3 Installation of Indoor APs
3.5 Connecting the Network
Connect the Ethernet interface of the AP to an Ethernet interface of the switch to
implement Internet or MAN access, as shown in Figure 3-10.
Wireless station
Internet
Switch
WA2200
Wired station
Wired station
Figure 3-10 Connect the AP to the network
3-8
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Chapter 4 Installation of Outdoor APs
The outdoor models of the WA2200 series are H3C WA2210X-G, H3C WA2220X-AG,
and H3C WA2220X-AGP. You can select an appropriate model according to the actual
requirement. The three outdoor models are waterproof, dustproof, and lightningproof.
4.1 Installation Flowchart
You can install your outdoor AP on a wall or a pole. As a wireless device, the installation
location directly affects the coverage and performance of wireless signals. Therefore, it
is recommended that the AP be installed by a professional. Figure 4-1 shows the
installation flowchart of the outdoor models.
Start
Install the wall-mounting
bracket
Install the fixing support on
the pole
Fix the AP onto the wallmounting bracket or the
mounting plate
Install the outdoor antenna
Install the RF cable
Install the Ethernet cable/
fiber cable
Connect the power supply
End
Figure 4-1 Installation flowchart of the outdoor models
4.1.1 Installing the AP
The following describes how to install the AP on a wall and a pole respectively.
I. Installing the AP on a wall
Figure 4-2 illustrates the installation flowchart of the AP on a wall.
4-1
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Start
Mark
Drill holes
Install anchors
Fix the wallmounting bracket
Fix the AP
End
Figure 4-2 Installation flowchart of the AP on a wall
1)
Mark
Step
Operation
Put the wall-mounting bracket on the installation position against the wall.
Mark three expansion screw holes on the wall. For the distance (in mm)
between the expansion screw holes, see Figure 4-3.
Note:
The wall-mounting bracket is not supplied unless ordered.
4-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Figure 4-3 Wall-mounting bracket structure and positions of screw holes
2)
Drill holes
Step
Operation
Use a percussion drill with a 6-mm (0.24-in) bit to drill holes on the three
markings.
Observe the following precautions when drilling:
Hold the drill handle with both hands, with the bit perpendicular to the wall surface,
and prevent wall damage or tilted holes.
The hole depth should be the anchor length plus the bit length. Each hole should
have the same depth. Remove the dust from the hole before measuring the hole
depth. Use a vacuum cleaner to prevent dust from spreading around.
If the wall surface is too solid and slippery to locate the bit, punch a notch first.
3)
Install anchors
4-3
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Note:
Before installation, remove dust inside and around all holes with a vacuum cleaner, and
then measure the distances between holes. If there is a large error, mark and drill holes
again.
Step
Operation
Put an anchor into each hole vertically.
Tap the flat end of the anchor with a rubber hammer until the anchor is flush
with the wall surface.
4)
Fix the wall-mounting bracket
Step
Operation
Align the three holes in the wall-mounting bracket with the anchors and
insert three expansion screws through the installation holes into the
anchors.
Adjust the position of the wall-mounting bracket and tighten the expansion
screws.
5)
Fix the AP
Step
Operation
Method 1: Align the two installation holes in the AP with the corresponding
holes in the wall-mounting bracket and then use two screws to fix them.
Method 2: Insert a screw into each installation hole in the AP, but do not
tighten them. Then insert the screws into the corresponding holes in the
wall-mounting bracket.
Tighten the screws so that the AP touches against the wall-mounting
bracket, as shown in Figure 4-4.
4-4
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Screw M10×12
Figure 4-4 Install the outdoor AP on a wall
II. Installing the AP on a pole
The fixing support for installing the outdoor AP on a pole consists of two major
components: a pair of V-shaped brackets and a mounting plate. The outdoor AP can be
fixed on a vertical or horizontal pole with an outer diameter of 60 to 110 mm (2.36 to
4.33 in) through the fixing support. The tilt of the AP is adjustable.
On the top of a building, the outdoor AP is usually installed on a pole.
Follow these steps to install the outdoor AP on a pole:
1)
As shown in Figure 4-5, fix the pole base onto the top surface of a building or onto
a cement pier.
4-5
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Figure 4-5 Pole and pole base
2)
Fix the mounting plate onto one V-shaped fixing bracket with screws.
3)
Fix the pair of V-shaped fixing brackets on a vertical or horizontal pole with bolts,
flat washers, spring washers, and nuts (see Figure 4-6 or Figure 4-7).
Figure 4-6 Install the outdoor AP on a vertical pole
4-6
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Bolt
M10 nut
#10 spring washer
#10 flat washer
V-shaped fixing bracket
Mounting plate
AP
Figure 4-7 Install the outdoor AP on a horizontal pole
4)
Fix the AP onto the mounting plate with screws (see the dashed line and arrow in
Figure 4-6 or Figure 4-7).
Note:
You can first install the fixing support onto the pole and then the AP onto the mounting
plate, or vice versa.
4.1.2 Installing an Outdoor Antenna
There are two types of outdoor antennas: directional antenna and omni antenna. An
omni antenna can be directly installed on an outdoor AP.
I. Installing a directional outdoor antenna on a pole
Note:
You should select such an installation location for the pole that the antenna direction
and tilt could be adjusted freely.
4-7
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Follow these steps to install a pole on a parapet:
1)
Weld the lightning rod onto the tip of the pole.
2)
Install the pole on a parapet or cement pier.
3)
Use a 40 × 4 mm (1.57 × 0.16 in) flat steel to connect the pole to the ground grid
4)
Use pole-mounting brackets to install the directional outdoor antenna on the pole.
The pole should be vertical to the building top surface, as shown in Figure 4-8 and
Figure 4-9.
Figure 4-8 Install a directional outdoor antenna on a parapet
Lightning rod
Pole-mounting
brackets
2500mm
Directional
outdoor antenna
Φ75mm
Antenna support
(antenna pole)
500mm
Steel wire
Cement pier
1500mm
Flat steel
To the
grounding grid
Figure 4-9 Install a directional outdoor antenna on a building top surface or cement pier
4-8
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
If there are parapets around the building top and the parapets are 1200 mm (47.24
in) high or higher, install the antenna pole on a parapet with expansion bolts and
fix the directional outdoor antenna onto the pole with pole-mounting brackets (see
the left diagram in Figure 4-8).
If there are parapets around the building top and the parapet height is less than
1200 mm (47.24 in), fix one point of the pole to the parapet with one expansion bolt
and the other point to the building top surface with another expansion bolt, and fix
the directional outdoor antenna onto the pole with pole-mounting brackets (see the
right diagram in Figure 4-8).
If there is no parapet around the building top, first use expansion bolts tosecure
the pole vertically on the building top surface or cement pier, and then use
pole-mounting brackets to fix the directional outdoor antenna onto the pole, as
shown in Figure 4-9.
II. Installing an omni outdoor antenna on a pole
When installing an omni outdoor antenna on a pole, observe the following precautions:
The pole should be 35 to 50 mm (1.38 to 1.97 in) in diameter. Usually, a round
steel with a diameter of 50 mm (1.97 in) is adopted.
The top of the pole should be flush with the upper clamp, as shown in Figure 4-10.
The antenna height should meet the signal coverage requirement and the tip of
the antenna should fall within the 45° protection angle of the lightning rod.
Usually, no lightning rod is directly soldered onto an omni antenna pole (no metal object
is allowed within one meter in the horizontal direction of the omni antenna). Instead, a
lightning rod is set on a separate pole between two omni antenna poles and the
lightning rod is high enough to keep the tip of omni antennas within the protection
angle.
4-9
Installation Manual
H3C WA2200 Series WLAN Access Points
45°
Lightning protection angle
Chapter 4 Installation of Outdoor APs
45°
Lightning rod
Omni outdoor
antenna
Clamp
Antenna pole
Figure 4-10 Install omni antennas
If the lightning rod cannot be installed on a separate pole owing to the environment
limitation, the installation method shown in Figure 4-11 can be adopted. In this case, the
lightning rod pole should be at least one meter away from the omni antenna pole.
4-10
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Lightning rod
45°
Omni outdoor
antenna
>1000 mm
3000 mm
Clamp
Angle steel
Antenna pole
Figure 4-11 Install an omni antenna under a special environment
Note:
In Figure 4-11, the antenna pole is welded with two angle steels to the lightning rod
pole, instead of a cement pier.
III. Installing an omni antenna on the AP directly
A low-gain omni rod antenna can be directly installed on the AP. The installation
procedure is as follows:
1)
Screw a feeder lightning arrester onto the downward 2.4-GHz antenna interface.
2)
Screw the omni rod antenna onto the N-type connector of the feeder lightning
arrester.
3)
Ground the feeder lightning arrester with a grounding cable. (See Figure 4-12)
4)
Ground the AP with a grounding cable.
4-11
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Figure 4-12 Install an omni antenna on the AP directly
Note:
After the omni antenna is installed on the AP, the antenna should be at least one
meter away from the pole or other metal objects.
The outdoor AP and the feeder lightning arrester are each equipped with a
3-meter-long grounding cable. If the length is not long enough, you need to supply
longer grounding cables. For the grounding requirements, refer to section 2.3.4
“Grounding and Lightning Protection” on page 2-4.
You are recommended to install the feeder lightning arrester on the antenna side.
4.1.3 Connecting External Cables
Caution:
Before connecting external cables, check that all power lines are disconnected, and
that there is no dangerous voltage on the neutral (N) line.
External cables to be connected include an RF cable, Ethernet cable, fiber cable,
grounding cable, and power cord.
4-12
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
I. Connecting the RF cable
The RF cable refers to the cable between the antenna interface and the antenna.
Follow these steps to connect the RF cable:
1)
Screw one end of the feeder lightning arrester onto the antenna interface.
2)
Connect one end of the RF cable to the feeder lightning arrester and the other end
to the outdoor antenna.
3)
Wrap each joint with insulation tape first, and then with waterproof tape.
Note:
It is recommended to install a feeder lightning arrester on each antenna interface
and ground it well.
A finished RF cable with a fixed length can be shipped with the AP if ordered. If such
an RF cable is not long enough, you should provide a longer RF cable and an
N-type RF connector and prepare the cable at the site.
Distinguish the stickiness of the two sides of waterproof tape. Before wrapping a
cable joint, stretch the waterproof tape so that the width is three quarters of the
original one to ensure the tightness.
II. Connecting an Ethernet cable
Caution:
Follow the steps below to connect an Ethernet cable. Otherwise, the AP may get
damaged
1)
As shown in Figure 4-13, Figure 4-14, and Figure 4-15, route the waterproof
Ethernet cable from the equipment room to the AP installation location.
4-13
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Outdoor
Antenna
RF coaxial
Indoor
AP
LAN switch
Ethernet Cable
Port lightning protector
AC
power
Grounding cable
Power adaptor
Figure 4-13 Connect the Ethernet electrical interface to the uplink device
Figure 4-14 Connect the Ethernet optical interface to the uplink device
4-14
Installation Manual
H3C WA2200 Series WLAN Access Points
Power
Chapter 4 Installation of Outdoor APs
(Surge) To AP
To Network
Ethernet cable
Ethernet cable
Grounding cable
AC power(220V)
Figure 4-15 Exploded view of the port lightning protector (PoE)
Note:
If the uplink device is a PoE switch, no port lightning protector or power adapter is
required.
If the Ethernet optical interface serves as an uplink data interface, the Ethernet
electrical interface only serves as a PoE interface.
There are two Ethernet interfaces on the power injector, as shown in Figure 4-15.
Ensure that the Ethernet interface on the surge side is connected to the AP.
Whether the AP is powered by a PoE switch or the power injector, ensure that the
AP has been installed as required before power-on.
2)
Prepare an Ethernet cable connector
Since an Ethernet cable needs to pass through a waterproof cover for waterproof
purpose (an Ethernet cable with an RJ-45 connector is unable to pass through), you
need to prepare an Ethernet cable connector on site. Usually a category-5 or enhanced
category-5 twisted pair cable is adopted. Figure 4-16 shows an Ethernet cable
connector.
4-15
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
RJ-45 connector
Figure 4-16 Ethernet cable connector
Ethernet cables fall into straight-through Ethernet cables and crossover Ethernet
cables.
Straight-through Ethernet cable: The wires of a twisted pair cable are crimped in
the same sequence in the RJ-45 connectors at both ends. A straight-through cable
is used to connect a terminal device (such as PC or router) to a hub or LAN Switch.
Crossover Ethernet cable: The wires of a twisted pair cable are crimped in
different sequences in the RJ-45 connectors at both ends. A crossover Ethernet
cable is used to connect a terminal device (such as PC or router) to another
terminal device. You can make such a cable by yourself.
Table 4-1 RJ-45 straight-through Ethernet cable pinouts
Pin of
RJ-45
connector
Signal
Category-5 twisted
pair cable
Signal direction
Pin of
RJ-45
connector
Tx+
White (orange)
Æ
Tx-
Orange
Æ
Rx+
White (green)
Å
—
Blue
—
—
White (blue)
—
Rx-
Green
Å
—
White (brown)
—
—
Brown
—
4-16
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Table 4-2 RJ-45 crossover Ethernet cable pinouts
Pin of
RJ-45
connector
Signal
Category-5 twisted
pair cable
Signal direction
Pin of
RJ-45
connector
Tx+
White (orange)
Æ
Tx-
Orange
Æ
Rx+
White (green)
Å
—
Blue
—
—
White (blue)
—
Rx-
Green
Å
—
White (brown)
—
—
Brown
—
Note:
When distinguishing or preparing these two types of Ethernet cables, you can refer
to the above tables. Since the Ethernet interface of the WA2200 series is
auto-sensing, these two types of Ethernet cables can be used for the Ethernet
interface.
Refer to Table 4-1 and Table 4-2 to arrange the wire sequence when preparing an
Ethernet cable. Otherwise, the communication quality will not be high, even if the
devices at both ends can communicate.
The Ethernet cable should be equipped with a waterproof sheath when routed
outdoors. If possible, cable routing in waterproof tubes is recommended.
3)
Insert the Ethernet cable connector into the Ethernet interface, as shown in Figure
4-17.
4-17
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Ethernet connector
Waterproof cover
Sealing nut
Joint between connector and cable
Figure 4-17 Insert the Ethernet cable connector into the Ethernet interface
4)
First tighten the waterproof cover and then the sealing nut.
5)
Use waterproof tape to wrap the joint between the waterproof cover and the cable.
III. Connecting an optical fiber
Caution:
Follow the steps below to connect a fiber cable. Otherwise, the AP may get damaged.
You need to configure an SFP module and a waterproof cover when connecting the AP
to an uplink device through a fiber cable, as shown in Figure 4-18.
Figure 4-18 Connect a fiber cable
4-18
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Follow these steps to connect a fiber cable:
1)
Insert an SFP module into the Ethernet optical interface on the AP.
2)
Insert the LC connectors of two ZX fibers with a waterproof cover into the two
optical interfaces on the SFP module.
3)
First tighten the waterproof cover and then the sealing nut.
4)
Use waterproof tape to wrap the joint between the waterproof cover and the fiber
cable.
5)
Splice the tail fibers with those of the uplink device, and bind the joints with
waterproof tape, respectively.
4.1.4 Powering On the AP
After all cables are correctly connected as shown in Figure 4-19, power on the AP and
check the status of the LEDs. For the description of the LED status, refer to section
1.2.1 “LEDs” on page 1-3.
4-19
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
Outdoor antenna
RF cable
Outdoor antenna
Grounding cable for
feeder lightning arrester
Grounding cable
Ethernet cable
Fiber cable
Figure 4-19 Connection of external cables of the AP
4-20
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 4 Installation of Outdoor APs
4.2 Connecting the Network
In practice, the AP can be connected to the Internet or a MAN through an Ethernet
interface, as shown in Figure 4-20.
Figure 4-20 Connection between the AP and Internet
Caution:
A special outdoor waterproof Ethernet cable is required to connect the AP and
waterproof treatment should be made to the Ethernet cable at the outlet of the chassis.
4-21
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
Chapter 5 Software Setting
The WA2200 series can work in the FIT mode or FAT mode. When setting the AP, you
must first determine its working mode. The software of the WA2200 series has been
loaded and debugged before delivery. After the installation, you can debug the software
of the system.
5.1 Working Mode Switching
The WA2200 series can work in the FAT mode, or cooperate with a wireless controller
to work in the FIT mode, and they can switch between the FIT mode and the FAT mode.
By default, the WA2200 series work in the FAT mode.
Before switching, identify the current working mode of the AP to determine whether it is
necessary to perform a mode switching.
5.1.1 Identifying the Current Working Mode
Follow these steps to identify the current working mode of the AP:
Step
Operation
Connect one end of a serial cable to the serial interface on the maintenance
terminal and the other end to the console interface on the AP, as shown in
the figure below:
Run a terminal emulation program on the maintenance terminal and set the
communication parameters as follows:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None:
Power on the AP and press Ctrl+B to enter BootWare menu. Select 9 to
enter a submenu and then select 1 to display the current working mode.
5-1
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
5.1.2 Switching from the FAT Mode to the FIT Mode
Follow these steps to switch from the FAT mode to the FIT mode:
Step
Operation
Connect one end of a serial cable to the serial interface on the maintenance
terminal and the other end to the console interface on the AP, as shown in
the figure below:
Run a terminal emulation program on the maintenance terminal and set the
communication parameters as follows:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Determine whether the AP contains the FIT image file, namely,
WA2200_fit.bin file in the Flash by using the dir command in user view. By
default, the AP contains both the FAT image file and the FIT image file.
Specify the image file for the next boot by using the boot-loader file
wa2200_fit.bin main command in user view.
5.1.3 Switching from the FIT Mode to the FAT Mode
Follow these steps to switch from the FIT mode to the FAT mode:
Step
Operation
Associate the FIT AP with the access controller (AC) by reference to section
5.3.1 “Associating a FIT AP with the AC on page 5-2.
Configure the AP to work in the FAT mode by using the wlan ap-execute
ap-name conversion-to-fatap command in system view. The ap-name
argument in the command is the name of the AP whose working mode
needs to be switched. If the FAT image file already exists in the AP, the AP
will successfully switch from the FIT mode to the FAT mode. You can log in
to the AP through the console interface.
5.2 Setting Up a Configuration Environment
You can set up a connection with the AP through the console interface or telnet to the
telnet-enabled AP through the Ethernet interface to perform software debugging. You
cannot directly manage the AP working in the FIT mode, but you can by associating it
5-2
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
with an AC. This section only describes the software configuration for the AP working in
the FAT mode.
5.2.1 Setting Up a Connection with the AP Through the Console Interface
Follow these steps to set up a connection with the AP through the console interface:
Step
Operation
Connect one end of a serial cable to the serial interface on the maintenance
terminal and the other end to the console interface on the AP, as shown in
the figure below:
Run a terminal emulation program on the maintenance terminal and set the
communication parameters as follows:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Power on the AP and the POST result is displayed on the maintenance
terminal. When POST completes, press Enter to log in to the command line
interface.
5.2.2 Telneting to the AP
Follow these steps to telnet from the maintenance terminal to the AP:
Step
Operation
Connect the maintenance terminal to the Ethernet interface of the AP over a
LAN, as shown in the figure below.
5-3
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
Step
Operation
Run the Telnet program on the maintenance e terminal and enter the IP
address of the AP to log in to the command line interface.
By default, Telnet is disabled on the AP. Therefore, you need to enable Telnet on the AP
and configure the IP address, login username, and password if you want to use Telnet.
For the detailed configuration procedure, refer to section 5.2.3 “Configuring Telnet” on
5-2.
5.2.3 Configuring Telnet
Follow these steps to configuring Telnet:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
[H3C]telnet server enable
% Start Telnet server
[H3C]
Enable Telnet.
Enter VTY view
[H3C]user-interface vty 0 4
[H3C-ui-vty0-4]
Set a Telnet authentication mode, for example, none authentication.
[H3C-ui-vty0-4]authentication-mode none
[H3C-ui-vty0-4]
Set the user priority level, for example, 3.
[H3C-ui-vty0-4]user privilege level ?
INTEGER<0-3> Specify privilege level
[H3C-ui-vty0-4]user privilege level 3
[H3C-ui-vty0-4]
Note:
In the none authentication mode, you need to enter the password h3capadmin to
telnet to a FIT AP, but no password to telnet to a FAT AP.
In the password authentication mode, you need to first enter the default password
h3capadmin and then the authentication password to telnet to a FIT AP, but only the
authentication password to telnet to a FAT AP.
5-4
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
5.3 Configuring a FIT AP
A FIT AP needs to cooperate with the AC and there is originally no configuration on the
FIT AP. All configurations of the FIT AP are first performed on the AC and then sent to
the FIT AP. Figure 5-1 shows the connection between the FIT AP and the AC.
AC
Switch
Fit AP(WA2200)
Figure 5-1 Connection between a FIT AP and the AC
5.3.1 Associating a FIT AP with the AC
I. Viewing the system information of a FIT AP
Since a FIT AP is uniquely associated with the AC by the serial-ID of the FIT AP, you
need to first view the serial-ID of the FIT AP. Each model of the WA2200 series has a
model number. The serial-ID and the model number of a FIT AP are set before delivery.
Follow these steps to view the system information of a FIT AP:
Step
Operation
Display the system information of a FIT AP in user view:
display wlan ap
Display AP Profile
-----------------------------------------------Model Number
: WA2210_AG
Description
: -NAAP Address
: 192.168.3.4
AC Address
: 192.168.3.1
Serial-ID
: 1234567891
State
: Run
H/W Version
: Ver.A
S/W Version
: V100R001B01D001(270549120)
Boot Version
: 100
Mode
: Split Mac Mode
-----------------------------------------------Unicast static AC IPv4 address: -NAUnicast static AC IPv6 address: -NA-----------------------------------------------
5-5
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
II. Associating a FIT AP with the AC
Follow these steps to associate a FIT AP with the AC:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create AP view for the FIT AP on the AC, with the view type consistent with
the model number of the FIT AP.
For example, create AP view with the name being aptest2 and the type
being WA2210_AG.
[[H3C]wlan ap aptest2 model WA2210_AG
[H3C-wlan-ap-aptest2]
Configure the corresponding serial-ID of a FIT AP in AP view, for example,
1234567891.
[H3C-wlan-ap-aptest2]serial-id 1234567891
[H3C-wlan-ap-aptest2]
Configure the first RF interface in AP view and enable and the RF interface.
For example, set the RF type of the first RF interface in AP view named
aptest2 to 802.11a and the channel number to 36, and enable the RF
interface.
[H3C-wlan-ap-aptest2]radio 1 type 11a
[H3C-wlan-ap-aptest2-radio-1]channel 36
[H3C-wlan-ap-aptest2-radio-1]radio enable
[H3C-wlan-ap-aptest2-radio-1]
After the above operations, AP view named aptest2 is associated with the FIT AP
whose serial-ID is 1234567891 and you can configure the FIT AP on the AC.
5.3.2 Configuring a FIT AP on the AC
Configure a WLAN extended service set (WLAN-ESS), service template, and radio
policy on the AC, and then bind them to AP view. After that, the AC will automatically
send the configuration information to the associated FIT AP.
I. Configuring a WLAN-ESS
Follow these steps to configure a WLAN-ESS:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a WLAN-ESS, for example, WLAN-ESS 101.
[[H3C]interface WLAN-ESS 101
[H3C-WLAN-ESS101]
5-6
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
II. Configuring a service template
Follow these steps to configure a service template:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a service template.
For example, create clear service template 101.
[H3C]wlan service-template 101 clear
[H3C-wlan-st-101]
Configure an authentication method.
For example, configure the open-system authentication method.
[H3C-wlan-st-101]authentication-method open-system
[H3C-wlan-st-101]
Configure the SSID.
For example, set the SSID to fytest1.
[H3C-wlan-st-101]ssid fytest1
[H3C-wlan-st-101]
Bind a WLAN-ESS to the service template.
For example, bind WLAN-ESS 101 to the service template.
[H3C-wlan-st-101]bind WLAN-ESS 101
[H3C-wlan-st-101]
Enable the service template.
[H3C-wlan-st-101]service-template enable
[H3C-wlan-st-101]
III. Configuring a radio policy
Follow these steps to configure a radio policy:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a radio policy, for example, radio policy 1.
[H3C]wlan radio-policy 1
[H3C-wlan-rp-1]
5-7
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
IV. Binding the configurations to AP view
Follow these steps to bind the configurations to AP view:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Enter AP view and then radio view.
For example, enter AP view named aptest2 and then radio 1 view.
[H3C]wlan ap aptest2
[H3C-wlan-ap-aptest2]radio 1
[H3C-wlan-ap-aptest2-radio-1]
Bind a radio policy and a service template to an RF interface in AP view.
For example, bind radio-policy 1 and service template 101 to the first RF
interface in AP view named aptest2.
[H3C-wlan-ap-aptest2-radio-1]radio-policy 1
[H3C-wlan-ap-aptest2-radio-1]service-template 101
[H3C-wlan-ap-aptest2-radio-1]
After the above configurations, wireless stations can detect and access the network
whose SSID is fytest1.
5.3.3 Security Setting
For the purpose of security, an encryption method can be applied to the authentication
of wireless stations and communication between wireless stations and the FIT AP. The
following describes how to set the WEP104 encryption method on the AC.
I. Setting the encryption template
Follow these steps to set the encryption template:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a service template, for example, encryption template 22, and enter
its view.
[H3C]wlan service-template 22 crypto
[H3C-wlan-st-22]
5-8
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
Step
Operation
Configure the TKIP encryption template.
Configure an encryption template for SSID testwep104, with the encryption
method being WEP104, key-id being 1, and key being 1234567980123.
[H3C-wlan-st-22]ssid testwep104
[H3C-wlan-st-22]bind WLAN-ESS 22
[H3C-wlan-st-22]authentication-method open-system
[H3C-wlan-st-22]cipher-suite wep104
[H3C-wlan-st-22]wep default-key 1 wep104 pass-phrase 1234567890123
[H3C-wlan-st-22]wep key-id 1
[H3C-wlan-st-22]service-template enable
5.4 Configuring a FAT AP
5.4.1 System Setting
The following simply describes how to configure a FAT AP so that wireless stations can
access it.
I. Configuring a WLAN-BSS
Follow these steps to configure a WLAN basic service set (WLAN-BSS):
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a WLAN-BSS, for example, WLAN-BSS 2.
[H3C]interface WLAN-BSS 2
[H3C-WLAN-BSS2]
II. Configuring a service template
Follow these steps to configure a service template:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Create a service template.
For example, create clear service template 2.
[H3C]wlan service-template 2 clear
[H3C-wlan-st-2]
Configure an authentication method, for example, open-system
authentication.
[H3C-wlan-st-2]authentication-method open-system
[H3C-wlan-st-2]
5-9
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
Step
Operation
Set the SSID.
For example, set the SSID to testFatAP2.
[H3C-wlan-st-2]ssid testFatAP2
[H3C-wlan-st-2]
Enable the service template.
[H3C-wlan-st-2]service-template enable
[H3C-wlan-st-2]
III. Configuring an RF interface (WLAN-radio)
Bind the WLAN-BSS and service template to the specified RF interface.
Follow these steps to configure an RF interface (WLAN-radio):
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Enter WLAN-radio view, for example, WLAN-radio 1/0/1 view
[H3C]interface WLAN-Radio 1/0/1
[H3C-WLAN-Radio1/0/1]
Configure the RF type, for example, 802.11a.
[H3C-WLAN-Radio1/0/1]radio-type 11a
[H3C-WLAN-Radio1/0/1]
Set a channel number, for example, 36.
[H3C-WLAN-Radio1/0/1]channel 36
[H3C-WLAN-Radio1/0/1]
Bind the WLAN-BSS and service template to the specified RF interface.
For example, bind WLAN-BSS 2 and service template 2 to RF interface
WLAN-radio 1/0/1.
[H3C-WLAN-Radio1/0/1]service-template 2 wlan-bss 2
[H3C-WLAN-Radio1/0/1]
After the above configurations, wireless stations can detect and access the network
whose SSID is testFatAP2.
5.4.2 Setting a System Name and the System Clock
Enter command line view through telnet or the console interface.
I. Setting a system name
Multiple FAT APs in a network can be identified by their system names.
5-10
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
Follow these steps to set a system name:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Use the sysname command to set a system name for the AP, for example,
AP.
system-view
[H3C]sysname AP
[AP]
II. Setting the system clock
Follow these steps to set the system clock:
Step
Operation
Run the clock datetime command in user view to set a system time, for
example, 10:35:46, November 28, 2007.
clock datetime 10:35:46 2007/11/28
5.4.3 Security Setting
For the purpose of security, an encryption method can be applied to the authentication
of stations and communication between wireless stations and the FAT AP. The
following describes how to set TKIP encryption.
I. Setting port encryption for WLAN-BSS
Follow these steps to set port encryption for WLAN-BSS:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Enter WLAN-BSS view, for example, WLAN-BSS 3 view.
[H3C]interface WLAN-BSS 3
[H3C-WLAN-BSS3]
Set an encryption method for WLAN-BSS, for example, PSK authentication
with the key being 12345678.
[H3C-WLAN-BSS3]port-security port-mode psk
[H3C-WLAN-BSS3]port-security tx-key-type 11key
[H3C-WLAN-BSS3]port-security preshared-key pass-phrase 12345678
[H3C-WLAN-BSS3]undo dot1x multicast-trigger
[H3C-WLAN-BSS3]
5-11
Installation Manual
H3C WA2200 Series WLAN Access Points
Chapter 5 Software Setting
II. Setting the encryption template
Follow these steps to set the encryption template:
Step
Operation
Enter system view.
system-view
System View: return to User View with Ctrl+Z.
[H3C]
Enter service template view, for example, encryption template 3.
[H3C]wlan service-template 3 crypto
[H3C-wlan-st-3]
Configure the TKIP encryption template.
For example, configure the TKIP encryption template for SSID testFatAP3.
[H3C-wlan-st-3]ssid testFatAP3
[H3C-wlan-st-3]authentication-method open-system
[H3C-wlan-st-3]cipher-suite tkip
[H3C-wlan-st-3]security-ie wpa
[H3C-wlan-st-3]service-template enable
[H3C-wlan-st-3]
5-12
Compliance and Safety Manual
WA 2200 series Wireless LAN Access
Point
Table of Contents
Table of Contents
Chapter 1 Regulatory Compliance Information..........................1-1
1.1 Regulatory compliance standards......................................1-1
1.2 European Regulatory compliance......................................1-2
1.2.1 EU Compliance information.....................................1-2
1.2.2 EU Country Restriction in 2.4GHz band..................1-3
1.2.3 EU Country Restriction in 5GHz band.....................1-4
1.3 USA regulatory compliance ...............................................1-5
1.3.1 FCC Part 15.............................................................1-5
1.3.2 RF Requirements ....................................................1-5
Chapter 2 Safety Information Sicherheitsinformationen 安全信息2-8
2.1 General Requirements Allgemeine Anforderungen 通用要求2-8
2.2 Electricity Safety Elektrische Sicherheit 用电安全 .............2-9
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
List of Tables
List of Figures
Error! No table of figures entries found.
List of Tables
Table 2-1 Regulatory compliance standards ...........................1-1
ii
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
Chapter 1 Regulatory Compliance
Information
1.1 Regulatory compliance standards
Table 1-1 Regulatory compliance standards
Discipline
Standards
FCC Bulletin OET-65C
FCC Part 15.207 & 15.209 & 15.247
FCC Part 15.207 & 15.209 & 15.407
ETSI EN 300 328
ETSI EN 301 893
CISPR22 CLASS B
EMC & RF
EN 55022 CLASS B
CISPR24
EN 55024
EN 60601-1-2
IEC 61000-3-2
IEC 61000-3-3
ETSI EN 301 489-1
ETSI EN 301 489-17
1-1
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
Discipline
Standards
UL 60950-1:2003
CAN/CSA C22.2 No 60950-1-03
IEC 60950-1:2001
Safety
EN 60950-1/A11:2004
EN 50385
1.2 European Regulatory compliance
WA 2200 Series Wireless LAN Access Point complies with the
following European Directives: R&TTE Directive 1999/5/EC.
1.2.1 EU Compliance information
1)
CE Mark
Equipment may be operated in the following country:
AT
BE
CY
CZ
DK
EE
FI
FR
DE
GR
HU
IE
IT
LV
LT
LU
MT
NL
PL
PT
SK
SI
ES
SE
GB
IS
LI
NO
CH
BG
RO
TR
1-2
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
Note:
Select the country in which the product is installed to ensure product
operation is in compliance with local regulations. For information on
how to select the country, refer to the “Wireless Configuration
Command” module in H3C Wireless Control Manager Command
Manual.
2)
Intended use: IEEE 802.11 a/b/g radio LAN device.
1.2.2 EU Country Restriction in 2.4GHz band
WA 2200 series Wireless LAN Access Point may be used indoors
or outdoors in all countries of the European Community using the
2.4GHz band: Channel 1-13, except where noted below.
France
For 2.4 GHz, the output power is restricted to 10 mW EIRP when
the product is used outdoors in the band 2454 - 2483.5 MHz. There
are no restrictions when used in other parts of the 2.4 GHz band.
The frequency band 5470-5750MHz is not allowed.
Check http://www.arcep.fr/ for more details.
Latvia
The outdoor usage of the 2.4-GHz band requires an authorization
from
the
Electronic
Communications
http://www.esd.lv for more details.
1-3
Office.
Please
check
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
1.2.3 EU Country Restriction in 5GHz band
1)
The frequency band 5150-5250MHz can not be used
outdoors.
2)
This device support DFS function.
Austria
Only the frequency band 5150-5250MHz is allowed.
France
The frequency band 5470-5750MHz is not allowed.
Cyprus
The frequency band 5470-5750MHz is not allowed.
Czech Republic
The frequency band 5470-5750MHz is not allowed.
Hungary
The frequency band 5470-5750MHz is not allowed.
Slovakia
The frequency band 5470-5750MHz is not allowed.
Italy
This product meets the National Radio Interface and the
requirements specified in the National Frequency Allocation Table for
Italy. Unless this wireless LAN product is operating within the
boundaries of the owner's property, its use requires a “general
authorization”. Please check http://www.comunicazioni.it/it/ for more
details.
1-4
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
1.3 USA regulatory compliance
1.3.1 FCC Part 15
I. US Federal Communications Commission (FCC) EMC
Compliance
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
1.3.2 RF Requirements
1)
RF exposure Hazard Warning
1-5
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
To ensure compliance with the requirements of FCC RF exposure,
a minimum body to antenna distance of 20cm (8 inch) must be
maintained when the device is operated.
2)
RF Frequency Requirements
This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This device and its antenna
must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device is for indoor use only when it is operated at 5.15 to
5.25GHz frequency range.
High power radars are allocated as primary users of the 5.25 to
5.35GHz and 5.65 to 5.85GHz bands. These radar stations can cause
interference with and /or damage this device.
3)
Antennas
Only use the supplied antenna. Unauthorized antennas,
modifications or change to the antennas could violate FCC regulations
and void the user’s authority to operate the equipment.
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user authority to
operate the equipment.
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
1-6
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
2.1 General Requirements Allgemeine
Anforderungen通用要求
In order to reduce the technically unavoidable residual risk to a
minimum, it is imperative to follow the rules below:
Um das technisch bedingte Restrisiko auf ein Minimum zu
begrenzen, ist es unbedingt erforderlich, die folgenden Regeln zu
beachten:
为了避免对人和设备造成伤害，请认真执行下列要求：
Read all the instructions before operation.
Lesen Sie alle Anweisungen sorgfältig durch, bevor Sie mit
dem Arbeiten beginnen.
在进行操作前仔细阅读手册内容。
Do not block ventilation openings while the system is on,
and keep at least 5 cm distance from ventilation openings
and walls or other things which may block the openings.
Sorgen Sie dafür, dass die Öffnungen der Ventilation zu
keinem Zeitpunkt verschlossen, verstopft oder anderweitig
blockiert sind. Zwischen den Ventilationsöffnungen und
Wänden bzw. anderen Gegenständen muss stets ein
Abstand von mindestens 5cm bestehen.
2-8
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
设备在工作时必须确保通风口的畅通，确保设备离墙壁或是
其它的可能堵塞通风口的物体的间距至少 5cm。
For AC supplied model: To ensure the safety of the
equipment and human body, please unplug the AC power
connector and do not use the fixed terminal in the lightning
weather. Furthermore, please do not touch the terminal or
antenna connector in such weather.
Mit Wechselstrom betriebenes Modell: Um die Sicherheit
des Personals und der Ausrüstung zu gewährleisten, muss
der Stecker aus der Steckdose gezogen werden, wenn die
Gefahr eines Blitzeinschlages besteht. Verwenden Sie bei
Blitzgefahr keine festinstallierten Steckdosen. Berühren Sie
bei Blitzgefahr nicht die Antenne.
对于 AC 输入设备，为保证设备和人身安全，请在雷雨天气时
拔下 AC 电源连接器，并不要使用固定终端，或者不要接触该
终端或者天线。
2.2 Electricity Safety Elektrische Sicherheit 用
电安全
Conducting articles, such as watch, hand chain, bracelet
and ring are prohibited during the operation.
Es ist nicht erlaubt während dieser Arbeiten leitende
Gegenstände wie Uhren, Armbänder, Armreifen und Ringe
am Körper zu tragen.
在操作中不能穿戴导电性的物品，如：手表，手琏，手镯和
项链等。
When water is found in the rack, or the rack is damp, please
immediately switch off the power supply.
2-9
Compliance and Safety Manual
WA 2110-AG Wireless LAN Access
Point
Chapter 2 Safety Information
Sicherheitsinformationen 安全信息
Sollte sich Wasser im Baugruppenträger befinden oder der
Baugruppenträger feucht sein, ist die Energiezufuhr sofort
zu unterbrechen und das System abzuschalten.
当有液体进入机架或机架有损坏时，请立即切断电源。
When operation is performed in a damp environment, make
sure that water is kept off the equipment.
Muss in einem feuchten Umgebung gearbeitet werden, ist
sicherzustellen, dass kein Wasser in die Ausrüstung dringen
kann.
在潮湿环境下进行安装时，请避免液体进入设备。
2-10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2008:07:10 01:53:52Z
Modify Date                     : 2008:07:10 12:04:14+08:00
Page Count                      : 78
Creation Date                   : 2008:07:10 01:53:52Z
Mod Date                        : 2008:07:10 12:04:14+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Metadata Date                   : 2008:07:10 12:04:14+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools