Hangzhou Hikvision Digital Technology K1201MF Fingerprint Card Reader User Manual

Hangzhou Hikvision Digital Technology Co., Ltd. Fingerprint Card Reader

User Manual

Fingerprint Card Reader User Manual
Fingerprint and Card Reader User Manual i User Manual © 2017 Hangzhou Hikvision Digital Technology Co., Ltd. This manual is applied for fingerprint and card reader. Device Name Model Fingerprint and Card Reader DS-K1201MF DS-K1201EF DS-K1201SF It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product. About this Manual This Manual is subject to domestic and international copyright protection. Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision. Trademarks and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission. Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY
Fingerprint and Card Reader User Manual ii RELIANCE ON THIS MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. Support Should you have any questions, please do not hesitate to contact your local dealer.
Fingerprint and Card Reader User Manual iii Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference.
Fingerprint and Card Reader User Manual iv 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
Fingerprint and Card Reader User Manual v Use only power supplies listed in the user instructions: Model Manufacturer Standard DSA-12PFT-12FUK 120100 Dee Van Enterprise Co., Ltd. BS DSA-12PFT-12FAU 120100 Dee Van Enterprise Co., Ltd. AS DSA-12PFT-12FIN 120100 Dee Van Enterprise Co., Ltd. IS DSA-12PFT-12FUS 120100 Dee Van Enterprise Co., Ltd. IEC DSA-12PFT-12 FBZ 120100 Dee Van Enterprise Co., Ltd. NBR Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings  All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage.
Fingerprint and Card Reader User Manual vi  Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.  Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.  Please make sure that the power has been disconnected before you wire, install or dismantle the device.  When the product is installed on wall or ceiling, the device shall be firmly fixed.  If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.  If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) Cautions  Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).  Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.  The device cover for indoor use shall be kept from rain and moisture.
Fingerprint and Card Reader User Manual vii  Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).  Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.  Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.  Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.  Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs. Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. 0100001071027 The device must not be co-located or operating in conjunction with any other antenna or transmitter
Fingerprint and Card Reader User Manual 1 Content Chapter 1 Introduction ........................................................ 3 1.1 Product Overview ..................................................... 3 1.2 Product Appearance ................................................. 3 Chapter 2 Installation .......................................................... 5 2.1 Introduction for DIP Switch ...................................... 5 2.2 Definition of Cable .................................................... 6 2.3 Wiring Cables ........................................................... 6 2.4 Installing Card Reader ............................................... 7 Chapter 3 Sound Prompt and Indicator ................................ 9 Appendix: Tips for Scanning Fingerprint ................................. 11
Fingerprint and Card Reader User Manual 3 Chapter 1 Introduction 1.1 Product Overview Fingerprint and card reader is a kind of high-performance product, with a 32 bit high-speed processor. It communicates with access controller via the RS-485 protocol. And a built-in tamper-proof module helps to protect card reader from malicious damage. 1.2 Product Appearance 1 Figure 1-1 Front View 23 Figure 1-2 Rear View
Fingerprint and Card Reader User Manual 4 Table 1-1 Components Description No. Name 1 Fingerprint Scanner 2 Cable Interface of RS-485, Power, LED Control, etc. 3 DIP Switch
Fingerprint and Card Reader User Manual 5 Chapter 2 Installation 2.1 Introduction for DIP Switch The DIP switch module is shown below. The No. of DIP switch from left to right is 1 to 4, representing the RS-485 address. Figure 2-1 DIP Switch Module Table 1-2 Description of DIP Switch Icon Description 1 Represent ON in binary mode 0 Represent OFF in binary mode For example, the binary value of the following status is 1100. Figure 2-2 DIP Switch Module Note: The DIP switch of RS-485 address should reach the access control devices requirements. For different access control devices, the DIP switch addresses may be different.
Fingerprint and Card Reader User Manual 6 2.2 Definition of Cable The description of 5 cables is shown below. Table 1-3 Description of Cables Color Description Blue RS-485 - Yellow RS-485 + Red PWR (DC +12V) Black GND (Power Grounding) Black GND (RS-485 Grounding) 2.3 Wiring Cables Purpose: Wire the cables between the controller and the card reader, thus to establish the communication between them. Steps for RS-485 communication mode: 1. Set the DIP switch for RS-485 address. For Details, refer to 2.1 Introduction for DIP Switch. 2. Wire the cable between the controller and the card reader as shown below.
Fingerprint and Card Reader User Manual 7 Figure 2-3 Wiring for RS-485 Communication Mode 2.4 Installing Card Reader Before you start: Set the DIP switch. For details, refer to 2.1 Introduction for DIP Switch. Steps:
Fingerprint and Card Reader User Manual 8 1. Fix the mounting plate on the wall with 2 provided screws. Note: Do not warp the mounting plate when installing. 2. Connect the cables between the controller and the card reader. For details, refer to 2.3 Wiring Cables. 3. Unscrew the screw at the bottom of the card reader. 4. Buckle the card reader up to the plate. 5. Fasten the card reader to the plate with the set screw.
Fingerprint and Card Reader User Manual 9 Chapter 3 Sound Prompt and Indicator After the card reader is powered on, LED status indicator will turn green and blink for 1 time. Then it will turn red and blink for 3 times. At last the buzzer will send out a beep sound indicating the starting up process is completed. When using the card reader, it will send out different sounds prompt and the LED indicator to indicate different statuses. You can refer to tables below for detailed information. Table 1-4 Description of Prompt Sound Sound Prompt Description One beep Swiping card prompt For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card. Two rapid beeps The operation of pressing keys or swiping card is valid. Three slow beeps The operation of pressing keys or swiping card is invalid. Rapidly continuous beeps Prompt for tamper-proof alarm. Prompt for buzzer alarm. Slowly continuous beeps The card reader is unencrypted.
Fingerprint and Card Reader User Manual 10 Table 1-5 Description of LED Indicator LED Indicator Status Description Green (blink for 1 time), and red (blink for 3 times) The card reader is power on. Green and blinking For Card + Fingerprint authentication: prompt for pressing the fingerprint after swiping the card. The operation of configuring the fingerprint. Solid green for 2s The operation of swiping card is valid. Solid red Card reader is working normally. Red and blink for 3 times The operation of swiping card is invalid. Red and blinking For RS-485 protocol: Registering failed or card reader is offline.
Fingerprint and Card Reader User Manual 11 Appendix: Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center. Incorrect Scanning The figures of scanning fingerprint displayed below are wrong: Environment The scanner should avoid direct high light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint Side Edge II Vertical Edge I
Fingerprint and Card Reader User Manual 12 successfully. You can blow your finger and scan again after drying the finger. Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another finger and try again.
Fingerprint and Card Reader User Manual 13 UD06570B-A

Navigation menu