Hangzhou Tuya Information Technology WR4 Wi-Fi Module User Manual WR4
Hangzhou Tuya Information Technology Co.,Ltd Wi-Fi Module WR4
User Manual
WR4 DATASHEET Tuya Smart Wi-Fi Module 1. Product Overview WR4 is a low power consumption module with built-in connectivity solution designed by Hangzhou Tuya Information Technology Co., Ltd.The Wi-Fi Module consists of a highly integrated wireless radio chip W302 12E77H2 and some extra flash that has been programed with Wi-Fi network protocol and plenty of software examples.WR4 includea ARM CM4F,WLAN MAC,1T1R WLAN,maximum frequency reaches 125MHz,256K SRAM,2M byte flash and various peripheral resources. WR4 is a RTOS platform, embedded with all the Wi-Fi MAC and TCP/IP protocol function examples, users can customize their Wi-Fi product by using these software examples. 1.1 Features Integrated low power consumption 32-bit CPU, also known as application processor Basic frequency of the CPU can support 125 MHz Supply voltage : 3.3V Peripherals: 7 GPIO channels, 2 UART, 1 ADC Wi-Fi connectivity: 802.11 B/G/N20/N40 Channel 1 to 11 @ 2.4GHz Support WPA/WPA2 +24.5 dBm output power Support SmartConfig function for both Android and IOS devices WR4 DATASHEET External IPEX connecter antenna Operating temperature range: -20℃ to 85℃ 1.2 Main ApplicationFields Intelligent Building Intelligent home, Intelligent household applications Healthy devices Industrial wireless control Baby monitor Webcam Intelligent bus WR4 DATASHEET 2. Dimensions and Footprint 2.1Dimensions WR4 has 2 columns of Pins (2*8).The distance between each Pin is 1.5 mm. Size of WR4: 13.8mm(W)*15.5mm(L)*3.3mm(H) Figure 2 shows the dimensions of WR4. Figure 2. The dimensions of WR4 2.2 Pin Definition Table 1 shows the generalpin attributes of WR4 Table 1. The typical pin definitionof WR4 PIN NO. NAME TYPE DISCREPTION NC NC,No Connect ADC AI ADC terminal(input 5V maximally) EN I/O External reset singal(low level effects) A_19 I/O GPIOA_19 A_12 I/O GPIOA_12 A_0 I/O GPIOA_0, can not be pull‐up while booting, can be used as GPIO while in normal working mode A_5 I/O GPIOA_15 3.3V I/O Supply voltage (3.3V) GND I/O Ground 10 A_23 I/O UART0_TXD WR4 DATASHEET 11 A_18 I/O UART0_RXD 12 A_22 I/O GPIOA_22 13 A_15 I/O GPIOA_15 14 A_14 I/O GPIOA_14 15 A_29 I/O UART_Log_RXD (used to print module's internal information) 16 A_30 I/O UART_Log_TXD(used to print module's internal information) Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input. WR4 DATASHEET 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Table 3.1. Absolute Maximum Ratings PARAMETERS DESCRIPTION MIN MAX UNIT Ts Storage temperature ‐40 105 ℃ VCC Supply voltage ‐0.3 3.6 Static electricity voltage (human model) TAMB‐25℃ ‐ KV Static electricity voltage (machine model) TAMB‐25℃ ‐ 0.5 KV 3.2 Electrical Conditions Table 3.2. Electrical Conditions PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT Ta Working temperature ‐20 ‐ 85 ℃ VCC Working voltage ‐ 3.6 VIL IO low level input ‐0.3 ‐ VCC*0.25 VIH IO high level input VCC*0.75 ‐ VCC VOL IO low level output ‐ ‐ VCC*0.1 VoH IO high level output VCC*0.8 ‐ VCC Imax IO drive current ‐ ‐ 16 mA Cpad Input capacitor ‐ ‐ pF 3.3 Wi-Fi Transmitting Current Consumptions Table 3.3. Wi-Fi TX current consumption PARAMETERS MODE RATE Transmitting power TYPICAL UNIT IRF 11b 1Mbps +20.18dBm 287 mA IRF 11g 6Mbps +24.17dBm 255 mA IRF IRF 11n-HT20 MCS0 MCS0 +23.30dBm +22.97dBm 244 220 mA mA 11n-HT40 WR4 DATASHEET 3.4 Wi-Fi Receiving CurrentConsumptions Table 3.4. Wi-Fi RX currentconsumption PARAMETERS MODE TYPICAL UNIT IRF CPU sleep 90 mA IRF CPU active 120 mA 3.5 Working Mode CurrentConsumptions Table 3.5. The module working currentconsumption WORK MODE AT TA=25℃ TYPICAL MAX* EZ Mode UNIT WR4 is under EZ paring mode, Wi‐Fi indicator light flashes quickly 115 130 mA Standby Mode WR4 is connected, Wi‐Fi indicator light is on 50 110 mA Operation Mode WR4 is connected, Wi‐Fi indicator light is on 120 265 mA Disconnection Mode WR4 is disconnected, Wi‐Fi indicator light is off 35 90 mA Note: peak continuous time is about 5us. The parameter shown above will vary dependingon different firmware functions. 4. WLAN Radio Specification 4.1 Basic Radio Frequency Characteristics Table 41.Basic Radio frequency characteristics PARAMETERS Frequency band Wi‐Fi standard Data transmitting rate DESCRIPTION 2.412GHz to 2.462GHz IEEE 802.11n20/n40/g/b (Terminal 1‐11) 11b:1,2,5.5,11(Mbps) 11g:6,9,12,18,24,36,48,54(Mbps) 11n:HT20,MCS0~7 11n:HT40,MCS0~7 Antenna type U.FL RF external connector WR4 DATASHEET 4.2Wi-Fi TransmittingPower Table 4.2. Wi-Fi transmitting power PARAMETERS MIN TYPICAL MAX UNI RF peak output power, 802.11b CCK Mode 1M ‐ 20.18 ‐ dBm RF peak output power, 802.11g OFDM Mode 6M ‐ 21.41 ‐ dBm RF peak output power, 802.11n20 OFDM Mode MCS0 ‐ 22.30 ‐ dBm RF peak output power, 802.11n40 OFDM Mode MCS0 ‐ 21.45 ‐ dBm ‐10 ‐ 10 ppm ‐10 ‐ 10 ppm The Frequency error Table 4.3. Wi-Fi Receiving sensitivity 4.3Wi-Fi Receiving Sensitivity The Frequency error RF peak output power, 802.11n OFDM Mode MCS7 ‐ 13.5 ‐ dBm RF peak output power, 802.11g OFDM Mode 54M ‐ 14.5 ‐ dBm RF peak output power, 802.11b CCK Mode 11M ‐ 17.5 ‐ dBm MAX UNI PARAMETERS MIN TYPICAL WR4 DATASHEET 5. Antenna Information 5.1 Antenna Type External antenna and the FPC antenna is recommended. Figure 5.1. recommended antenna size 5.2 U.FL RF connector The parameter for U.FL RF connector is shown below: WR4 DATASHEET 6. Packaging Information And Production Guide 6.1 Mechanical Dimensions Figure 6.1. Top view of the module 6.2PCBRecommended Package Figure 6.2 PCB schematic Drawing 6.3 Production Guide The storage for the delivered module should meet the following condition: 1. The anti-moisture bag should be kept in the environment withtemperature< 30℃ and WR4 DATASHEET humidity< 85% RH. 2. The expiration date is 6 months since the dry packaging products was sealed. Cautions: 1. All the operators should wear electrostatic ringin the whole process of production. 2. While operating, water and dirt should not have any contact with the modules. 6.4 Recommended furnace temperature curve Figure 6.3. PCB Package DrawingRecommended furnace temperature curve FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC Label Instructions: The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID: 2ANDL-WR4”,or “Contains FCC ID: 2ANDL-WR4”, Any similar wording that expresses the same meaning may be used.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : baclsh47 Create Date : 2018:09:05 11:51:02+08:00 Modify Date : 2018:09:21 16:41:26-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2018:09:21 16:41:26-07:00 Format : application/pdf Title : Microsoft Word - WR4_User manual Creator : baclsh47 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:d540c82e-fe14-47f5-9131-b21d93db9ddd Instance ID : uuid:d94192a2-f45f-41e8-9027-48b8b7f42cb6 Page Count : 10EXIF Metadata provided by EXIF.tools