Hangzhou Wistar Mechanical and Electric Technology WISTAR-RS001 Emitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3266245
Application ID	EInzwkizdDY9UP/cKZo6fA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	175.33kB (2191627 bits)
Date Submitted	2017-01-21 00:00:00
Date Available	2017-01-21 00:00:00
Creation Date	2013-12-17 14:02:12
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2017-01-09 16:45:47
Document Title	风光感应器 无线 学习键 英 中性 A5 双面印刷2012.02.16-封稿.cdr
Document Creator	CorelDRAW
Document Author:	Administrator

User manual
Model:WSRS001 Brand:WISTAR
8.Testing mode
Wind-Light Sensor Instruction
1、Wind speed testing mode
When the sensor is in wind speed real-time testing mode, the figures reflect current wind speed outside. For example, the figure “1.0” represents real wind speed is 10km/h outside.
1.Technical Data
00
Power: Solar Panel + Rechargeable Lithium Battery (3.7V,180mAh)
Protection Index: IP44
Temperature: -20℃ to +60℃
Working Current: ≤12mA
Codes: Rolling Codes
Frequency: 433.92MHz
2. Structure
1) Short press the left button four times.
2) the dot in the middle is always on.
3) Short press the right button once, it will
come out from wind speed testing mode.
2、Light intensity testing mode
When the sensor is in light real-time testing mode, the figures reflect current light intensity outside. For example, the figure “10.” represents real light intensity is 10000Lux outside.
00
Solar panel
Base
1)Short press the right button four times.
2) the dot at the the right corner
of the LCD is always on.
3) Short press the left button once, it will
come out from light intensity testing mode.
Note: In light intensity testing mode, the numerical value displays the light intensity from 1000 to 100000lx. It shows“00.” below 1000lx, and “99”above
100000lx. For example, the figure “12.” represents 12000lx. It will return to initial interface 3 minutes later if there is no further operation is done to the sensor.
9.Function
Wind cup
1、The strong wind protection function
If the wind speed exceeds the set grade for 6 seconds
continuously, an Up order is given to the motor and the
awning will close automatically.
As long as real wind speed is higher than the set
grade, you cann't open the awning by any means
(manual control, emitter control and light sensor are invalid).
2、The light sensor function
If the light intensity exceeds the set grade for
10 minutes continuously, a Down order is given
to the motor and the awning opens automatically
Wind adjust button
If the wind speed falls below the set grade for 30
seconds continuously, the sensor sends signals
to the motor and activates the control by emitter
and light sensor.
Learning button
If the light intensity below the set grade for
10 minutes continuously, an Up order is given
to the awning and the awning closes automatically.
Wind threshold
Light threshold
Light adjust button
The sensor is wireless emitter which controls awning to open or close according to the change of light intensity. Also, it
detects real-time wind speed and control awning to close automatically if the wind exceeds set limit. It is powered by solar
panel . It is environmental-friendly.It can work continuously more than a year after fully charged.
04
Fixing components
RS 001 Instruction
Screw
01
3.Size
5.Code learning
220V Power
1) Switch on the power and
then the motor will vibrate.
2) Short press the learning
button one time.
3) The motor will vibrate. The
code learning is successful.
6.Set Wind Threshold
Long press for 2 seconds
1) Long press the left button for 2
seconds and the left numbers on
the LCD would flash.
2) Short press the left button and the
numbers will circulate from 0 to 5
3)Select the figure you want and then press the
right button one time to exit the setting. The
numbers stop flashing and the wind grade is set.
Chart 1-1 Wind Threshold Corresponding to Actual Wind Speed
4.Installation
Note: To make the system operate normally, please remember that the controller must be installed near the place where the
awning can be protected, and the place can reflects the surrounding's light intensity and wind speed. Please ensure that there
is no other same frequency (433.92MHz) device to work constantly; otherwise, the system will be interfered.
1. Please use the material offered by our company to install and fix the product in the suitable place.
2. Please make the product's mechanical position fit to the wind cup parallel the level surface, just as the installation drawing,
otherwise, it will affect the testing of the wind speed.
01.Installation
Close wind speed test
10km / h
15km / h
20km / h
30km / h
>40km / h
7.Set Light Threshold
OK
Long press for 2 seconds
90
02.Installation chart
2) Short press the right button and
the numbers will circulate from 0 to 5.
1) Long press the right button for 2
seconds and the right numbers on
the LCD would flash.
OK
90
3)Select the figure you want and then press
the left button one time to exit the setting. The
numbers stop flashing and the light intensity is set.
Chart 1-1 Light Threshold Corresponding to Actual Light Intensity
OK
OK
Light Threshold
90
Wind speed
Wind Threshold
90
02
Actual Light Intensity
Light Threshold
Actual Light Intensity
Close light intensity test
40000Lux
2000Lux
60000Lux
5000Lux
70000Lux
10000Lux
80000Lux
20000Lux
90000Lux
03
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Administrator
Title                           : 风光感应器 无线 学习键 英 中性 A5 双面印刷2012.02.16-封稿.cdr
Create Date                     : 2013:12:17 14:02:12+08:00
Creator Tool                    : CorelDRAW
Modify Date                     : 2017:01:09 16:45:47+08:00
Metadata Date                   : 2017:01:09 16:45:47+08:00
Producer                        : Corel PDF Engine Version 14.0.0.701
Document ID                     : uuid:4fe9eb71-79b7-494f-ad4c-e07b43275379
Instance ID                     : uuid:537e4ae7-1415-42c7-befd-89e972aefade
Page Count                      : 3
Author                          : Administrator

EXIF Metadata provided by EXIF.tools