Hans Grohe Pharo Dp Lift 2 M 20 Users Manual
DP Lift 2 M 20 to the manual 7f40aed6-225c-43ef-bbd3-f8436909778f
2015-02-09
: Hans-Grohe Hans-Grohe-Pharo-Dp-Lift-2-M-20-Users-Manual-563809 hans-grohe-pharo-dp-lift-2-m-20-users-manual-563809 hans-grohe pdf
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
Installation Instruction DP Lift 2 M 20 26 87x xx1 Corner fitting set 26 21x 000 Contents Contents Packing List Wall / Corner Installation Dimensions Diagram Panel Dimensions Fittings / Technical Data Fitting Items / Water Connections Overview Wall Installation Wall Installation Fitting Items / Water Connections Overview Corner Installation Corner Installation Thermostat Setting / Savety Function Trouble Shooting Spare Parts Cleaning Instruction Warranty Addresses 3 4 5 6 7 8 10 11 14 15 16 18 19 20 Packing List Fitting items Panel a a Handshower b Isiflex B shower hose 140 cm b c c 1 Angle bracket d 2 Hexagon head cap screws Ø 6 x 50 mm with d f e 2 Washer A 6,3 x 18 f 1 Set screw M 8 x 80 with 2 nuts M 8 and plug g SX 10 g Overhead shower e h plugs SX 8 h 2 Water connection elbows ½" with filter and non return valve Fitting items Corner Installation Set i Cover i k 2 Angle bracket l 4 Head screws Ø 4,5 x 60 mm with plugs q m 4 Washer A 5,3 x 15 k n Socket head cap screw M 8 x 18, washer A 8,4 o 2 Socket head cap screws M 6 x 16, nut M 6 o l n p 2 Washer A 6,4 q 2 EJOT screws KA 50 x 12 p m Tools free from acetic acid Wall / Corner Installation Dimensions Diagram Check for required minimum height of 87" from shower tray floor before starting installation Wall installation dimensions diagram Corner installation dimensions diagram Water connections (DN15, ½“) can be installed on the right or left wall alternatively. KW = cold water WW = hot water ½" connection ½" connection Before drilling the lower hole pay attention if hot and/or cold water supply pipes cross this area. Shower tray floor Shower tray floor Panel Dimensions The panel is movable 8" downward. The stated dimensions refer to the highest position of the panel. Fittings / Technical Data Flow heater: Applicable for flow heaters at min. 24 kW and 29 psi flow pressure before the Shower panel. Only one consumer possible, not two simultaneously. Overhead shower Aluminium profile Pressure differences: The pressures of the cold and hot water connections must be balanced. Tray Maintenance The non return valves must be checked regularly according with national or regional regulations (at least once a year!). Bodyshower Thermostat grip Shut-off/selection valve Handshower Shower hose Technical Data Minimum flow pressure Operating pressure Recommended operating pressure Test pressure Hot water temperature Safety stop Flow capacity at 44 psi Hand shower (1) Body showers, 6 jets (2) Overhead shower Overhead shower + body showers (3) Hand + body showers 29 psi max. 147 psi* 29.4-73.5 psi 235.2 psi max. 158 °F 100 °F 1,9 3,9 2,8 5,5 5,0 gpm gpm gpm gpm gpm * Check applicable codes The flow rates are limited to 2.5 gpm. These are the maximum flow rates permitted by the From • the function is guaranteed. Fitting Items / Water Connections Overview Wall Installation Fitting items / water connections wall installation Seal all drill holes with silicone free from acetic acid (not in scope of delivery) SW10 mm Before drilling the bottom holes pay attention if hot and/or cold water supply pipes cross this area. In this case, only drill on the side without any supply pipes. Dimensions Ø8 mm The installation dimensions stated in this installation instructions are ideal for people of approximately 70" in body height. The dimensions can be altered if required. In this case you will have to attend to the minimum height of 87" from shower tray floor, and alter all the required measurements as necessary. If the height of water connection are outside of the illustrated range, the drill measures have been adjusted accordingly. (attention for minimum room height of 87 from tub-floor) Flush through the supply pipes. SW13 mm Ø10 mm Wall Installation 1 2 1. 2. SW 24 mm 1. 2. Wall Installation 3 4 SW 2 mm SW 13 mm Adjustment Thermostatic mixer please see page 14 Fitting Items / Water Connections Overview Corner Installation Fitting items / water connections corner installation Seal all drill holes with silicone free from acetic acid (not in scope of delivery) 2x Before drilling the bottom holes pay attention if hot and/or cold water supply pipes cross this area. In this case, only drill on the side without any supply pipes. 2x SW 5 mm SW10 mm Dimensions The installation dimensions stated in this installation instructions are ideal for people of approximately 70" in body height. The dimensions can be altered if required. In this case you will have to attend to the minimum height of 87" from shower tray floor, and alter all the required measurements as necessary. If the height of water connection are outside of the illustrated range, the drill measures have been adjusted accordingly. (attention for minimum room height of 87 from tub-floor) Ø6 mm Flush through the supply pipes. 1x 2x SW 6 mm Ø6 mm 10 Corner Installation 1 2 3 11 Corner Installation 4 5 1. 2. SW 24 mm 12 1. 2. Corner Installation 6 7 SW 17 mm SW 13 mm Adjustment Thermostatic mixer please see page 14 13 Thermostat Setting / Safety Function Safety Function (1-5) The desired maximum temperature for example max. 108 °F can be pre-set thanks to the safety function 1 2 4 5 3 Thermostat Setting (6-7) - Set Quattrostat to "Hand shower". - Open Quattrostat, adjust thermostat to 100 °F. - Push thermostat grip on and align vertically (red button A points upwards), screw tight 6 7 A 14 Trouble Shooting 8" (150 N) English Fault water level is too low handshower delivering insufficient water temperature regulation not possible (only hot or cold water) Cause Remedy filter in angled hose connection is dirt filter of handshower dirty clean filter clean filter thermostatic cartridge defective exchange thermostatic cartridge at new installation: connection hose exchanged install connection hose correct shower is dripping cartridge of Quattrostat defective cartridge of Quattrostat stiff nut of cartridge screwed to tight exchange cartridge first screw nut of cartridge tight, than loosen the nut approx. 12° 15 Exchanging lateral shower head 1 16 Spare Parts 10 1 15 13 9 29 x 2,5 25 x 2 23 x 2 16 3 8 4 2 7 17 14 12 18 6 11 5 Pos. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Description head shower shower arm handshower handle for thermostat sleeve handle flange hose body shower escutcheon spray head cartridge on/off control thermostat cartridge sealing set shelf upper cover lower cover connetion hose 900 mm mounting kit handle with showerholder gas spring elbow NPT ½" sliding roller corner fitting set Nr./No./Nr. 97195XX1 97196XXX 98552XX1 38391XX1 95032XXX 10490XXX 97057XXX 25941XXX 97197001 97198XXX 28408XXX 96645000 94282000 95037000 97199000 97200XXX 97201XXX 97202000 97203001 98579XXX 98611000 97582000 98890000 2621X000 VE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 XXX = Colors 000 chrome plated 810 satinox 880 satin chrome 17 Cleaning Instruction English Cleaning Recommendation for Hansgrohe Products Modern sanitary tapware, kitchen mixers and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and reclamations, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Mixers and Showers Acids are necessary ingredients of cleaning materials for removing lime, however please pay attention to the following points when cleaning mixers and showers: • Only use cleaning material which is explicitly provided for this type of application, such as Hansgrohe’s Decalcifying Agent (A), which is available through the specialist sanitary trade. • Never use cleaning materials, which contain hydrochloric, formic or acetic acid, as they cause considerable damage. • Phosphoric acid is also restricted as it can cause damage. • Never mix any cleaning material with another. • Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads or micro fibre cloths. Cleaning Instructions for Mixers and Showers Please follow the cleaning material manufacturer’s instructions. In addition pay attention to the following points: • Clean the mixers and showers as and when required • The cleaning dosage and time the cleaner needs to take effect should be adjusted according to the product and the cleaner should not be left longer than necessary. • Regular cleaning can prevent calcification. • When using spray cleaner, spray first into a cloth or sponge never directly onto the sanitary tapware, as drops could enter openings and gaps and cause damage. • After cleaning rinse thoroughly with clean water to remove any cleaner residue. Important Residues of liquid soaps, shampoos and shower foams can also cause damage, so rinse with clean water after using. If the surface is already damaged, the effect of cleaning materials will cause further damage. Damage caused by improper treatment will not be covered by our guarantee. A Rubit Cleaning the hand and head shower With the manual cleaning function “Rubit”, jet former calcinations can be removed by simple rubbing. 18 Quiclean Cleaning the hand-shower Handshower with “Quiclean”, the cleaning function against calcinations. When the jet types are changed, small cleaning pins remove the calcinations. Warranty Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. („Hansgrohe“). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product which proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of the product. LENGTH OF WARRANTY Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you own the product and the home in which the product is installed. If you purchased the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Interaktiv and Retroaktiv products, and (ii) for 5 years, with respect to AXOR, ShowerPower and Pharo products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the product in any manner contrary to the product instructions. C. Labor or other expenses for the disconnection or return of the product for warranty service, or for installation or reinstallation of the product. D. Accessories or related products not manufactured by Hansgrohe. TO OBTAIN WARRANTY SERVICE Contact your Hansgrohe retailer, or write to Technical Service at: Hansgrohe Inc. 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Or, call Hansgrohe toll-free at (800) 334-0455. In requesting warranty service, you will need to provide 1. 2. 3. The sales receipt or other evidence of the date and place of purchase. A description of the problem. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492 Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe. When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid. EXCLUSIONS AND LIMITATIONS REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT. HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY). Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act. PRODUCT INSTRUCTIONS AND QUESTIONS Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you have questions at any time about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or write to us at the toll-free number and address printed above. 19 Hansgrohe · Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440 E-Mail: info@hansgrohe.com · Internet: www.hansgrohe.com 03/2009 9.05185.03 20
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-702 Create Date : 2009:03:11 10:51:39+01:00 Modify Date : 2009:03:11 14:03:48+01:00 Metadata Date : 2009:03:11 14:03:48+01:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 5948 bytes, use -b option to extract) Version ID : 1 Instance ID : uuid:b0e987fb-cff3-463c-abf0-12f74d17ac61 Document ID : adobe:docid:indd:1bcbc5c6-0e18-11de-899b-85900fc14804 Rendition Class : proof:pdf Derived From Instance ID : 1bcbc5c5-0e18-11de-899b-85900fc14804 Derived From Document ID : adobe:docid:indd:1bcbc5c4-0e18-11de-899b-85900fc14804 Derived From Version ID : 1 Manifest Link Form : ReferenceStream Manifest Placed X Resolution : 72.00 Manifest Placed Y Resolution : 72.00 Manifest Placed Resolution Unit : Inches Manifest Reference Instance ID : uuid:1EFC914B0D0811DB80518B7A30A00F15 Manifest Reference Document ID : uuid:1EFC914A0D0811DB80518B7A30A00F15 Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 20 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools