Hansol LCD B15GF-1 LCD Monitor User Manual H550 ENG

Download:
Mirror Download [FCC.gov]
Document ID	299055
Application ID	CLDuxeVq5+TfVS/LhIrOjA==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	96.99kB (1212350 bits)
Date Submitted	2003-01-27 00:00:00
Date Available	2003-01-27 00:00:00
Creation Date	2002-12-28 12:00:17
Producing Software	Acrobat Distiller 4.0.5 for Macintosh
Document Lastmod	2003-01-23 15:23:30
Document Title	Ç¥ÁöH550_ENG
Document Creator	QuarkXPress: PSPrinter 8.3.1
Document Author:	Á¤

15
Printed on the recyclable paper
www.hansolel.co.kr
Printed in Korea
Part No. 942205020001-01
USER'S MANUAL
TFT-LCD Color Monitor
INFORMATION TO USER :
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates, uses and can
radiate radio frequency energy and,if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or
television reception, which can be determined by determined by turning the
equipment off and on, the user is encouraged to try to crrent the interference by
one or more of the fllowing measures:
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
Table of Contents
Parts
Connection to Signal Source
the range of control Angle
Installing Monitor Driver
Name and Function of Front
Power Management Feature
10
Adjusting OSD
11
Standard Signal Table
18
Specification
19
Troubleshooting
20
Warning
22
3. Connect the equipment into an outlet on a circuit difference
from that to which the recerver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment
ENERGY STAR
As an ENERGY STAR partner, Hansol Electronics Inc.
has determined that this product meets energy Star guidelines
for energy efficiency.
Good Posture Guide
Parts
Place the monitor to face the user and then adjust the monitor angle.
Take a break (for about 10 minutes) at every hour during the work with monitor.
Refer to the following figure to take the correct posture.
about 50cm
Look down the monitor
below the horizon.
Adjust the monitor to
prevent reflection.
LCD Monitor
Relax shoulders and arms,
and sit back on the chair.
Adjust the monitor stand
to acquire required angle.
Maintain the arms horizontally
and place hands softly on
the keyboard.
Signal Cable
Stereo Cable(Option)
User's Manual /
Warranty Card
Installation Diskette
AC Power Cable
Keep feet flat on the ground.
2 - English
English - 3
Connection to Signal Source
Basic Connection
Port for AC power cable
Port for Audio cable from audio source.
Port for Head Phone or External Speaker
Port for signal cable from signal source.
< Power source connection >
The range of control Angle
How to Adjust the Stand
Forward 4
< Signal cable connection>
General
For Macintosh
Default
Adapter for Macintosh (Optional)
Refer to the table on the rear side of
the optional Macintosh adapter and
adjust DIP switch by the resolution.
1. Use 220 V or 110 V. (Free Voltage)
2. Connect monitor and Signal Source via Signal cable
3. Power on the monitor and computer.
4. Connection is finished.
4 - English
Backward 31
English - 5
Installing Monitor Driver
Run (Click) "Install" at Floppy Diskette driver and select the model name to
set the optimum display in Window 95, 98 or 2000, XP.
Use the Driver provided.
Automatic Installation
1. Insert the Diskette to the Floppy Diskette driver.
2. Double-click "Install.exe".
3. Select the model and click "OK" button.
4. Select inf file, and then click "OK" button.
5. Click "Exit" button to close the installation.
Click 'Advanced..'.
Click 'Monitor'.
Click 'Display a list of all...'.
Click 'Next>'.
Click 'Next>'.
Click 'Change..'.
Click 'Have Disk..'.
Manual Installation
1. Insert the Diskette to the Floppy Diskette driver.
2. Click 'My Computer' and follow the procedure below.
Select the driver and click 'OK'.
Click 'Next>'.
Click 'Control Panel'.
6 - English
Click 'Display'.
Click 'Settings'.
Click 'Next>'.
Click 'Finish'.
3. Select "Exit" if the monitor model is changed, and then reboot the Windows.
English - 7
Name and Function of Front
Front panel
Functions
Power button
Power button is located in the lower center of the Front Bezel.
You can push the button to turn on/off the power.
Power Indicating LED
Dark : Power off
Green : Normal mode
Green blinking : DPMS mode or Check Signal Cable mode.
On Screen Display (OSD) Function Button
OSD buttons on the front of bezel perform the following functions.
MUTE BUTTON
VOL BUTTON
MENU/EXIT BUTTON
+/
-/
SELECT/ AUTO BUTTON
POWER BUTTON
8 - English
BUTTON
BUTTON
MUTE : Press this button for mute control
MENU/EXIT : Press this button to display menus. if you press this button when
OSD is displayed, you can switch display to the previous menu and
exit menu.
SELECT/ AUTO : Press this button, when OSD is not displayed, to perform
automatic setting.
When OSD is displayed, You can select icons.
POWER : Power button.
+/
: By pressing these button when OSD is displayed, You can move
-/
cursor into the menus which you want.
After press the SELECT button, you can change gauge level or
select submenus.
When OSD is not displayed, you can adjust brightness or contrast.
VOLUME : Press this button for volume control
English - 9
Power Management Feature
The monitor is equipped with a power saving circuit that
confirms to the world-standard Display Power Manager Signalling
(DPMS) mode of Video Electronics Standard Association (VESA).
The power management feature requires that the video card of the
computer should support DPMS function.
Status
LED Sign
Power Consumption
Normal mode
Green ON
Normal Power
DPMS mode
Green Blinking
1 W or Below
Adjusting OSD
Brightness / Contrast
MENU
SELECT
1. Press the MENU button to access main menu.
2. Use
to move Brightness and Contrast ICON.
3. Press SELECT button into the submenu.
Brightness
DPMS with Audio (Option)
Mute ON
1W or Below
Mute OFF
10W or Below
SELECT
1. Use
to move Brightness ICON.
2. Press SELECT button to select it.
3. Use
to adjust the brightness.
No image is displayed with Green blinking.
Monitor is in power saving mode.
Use mouse or keyboard to release power saving mode.
No image is displayed without LED on.
Power cable plug must be pulled out.
Check the power plug on monitor and on the wall.
Contrast
SELECT
"Out of range" displayed on the screen.
This message is displayed when the signal from video card exceeds the
maximum frequency of the monitor. Readjust resolution and frequency in
accordance with the monitor capacity. (Refer to Standard Signal Table)
10 - English
1. Use
to move Contrast ICON.
2. Press SELECT button to select it.
to adjust the contrast.
3. Use
English - 11
Image
Phase
SELECT
MENU
1. Press the MENU button to access main menu.
2. Use
to move Image ICON.
3. Press SELECT button into the submenu.
SELECT
to move Phase ICON.
1. Press
2. Use SELECT button to select it.
3. Use
to correct fine trembling or Video noise.
Horizontal Position
Clock
SELECT
1. Use
to move H-Position ICON.
2. Press SELECT button to select it.
to adjust display left or right.
3. Use
According to the characteristic of video card,
control range can be changed.
SELECT
to move Clock ICON.
1. Use
2. Press SELECT button to select it.
3. Press or
to remove vertical noise.
( Adjusting clock phase is required after the
adjustment of clock.)
Vertical Position
Color
SELECT
1. Use
to move V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust display upward or downward.
According to the characteristic of video card,
control range can be changed.
12 - English
MENU
SELECT
1. Press MENU button to access main menu.
2. Use
to move Color ICON.
3. Press SELECT button into the submenu.
English - 13
Preset Color
OSD H-Position
MENU
SELECT
1. Use
to select the Mode 1, and Mode 2.
2. Press the Menu button to return previous state.
Mode 1 : Reddish white
Mode 2 : Bluish white
User Color
1. Use
to move User color ICON.
2. Press SELECT button to select it.
3. Use
to increase or decrease each color.
1. Use
to move OSD V-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD upward or downward.
OSD Time
OSD
SELECT
1. Press MENU button to access main menu.
2. Use
to move OSD ICON.
3. Press SELECT button into the submenu.
14 - English
OSD V-Position
SELECT
SELECT
MENU
1. Use
to move OSD H-Position ICON.
2. Press SELECT button to select it.
3. Use
to adjust OSD left or right.
SELECT
to move OSD Time ICON.
1. Use
2. Press SELECT button to select it.
3. Use
to adjust OSD display time.
4. Press Menu button to return main menu.
English - 15
Special
MENU
SELECT
1. Press the MENU button to access main menu.
to move Special ICON.
2. Use
3. Press SELECT button into the submenu.
Auto-Config
Information
MENU
SELECT
1. Use
to move the Information ICON.
2. Press SELECT button to select it.
You can know display information
Accoding to the characteristic of video card,
display information can be incorrect
Language
Sound
Auto-Config
(Option)
MENU
SELECT
1. Use
to move Language ICON.
2. Press SELECT button to select it.
to select language.
3. Use
MENU
SELECT or
VOL BUTTON
1. Use
to move Sound ICON.
2. Press SELECT button to select it.
3. Use
to control volume.
Auto-Config
Menu Reset
SELECT
1. Use
to move the Factory Reset ICON.
2. Press SELECT button to return to default setting.
16 - English
English - 17
Specification
Standard Signal Table
Horizontal Frequency
(KHz)
Vertical Frequency
(Hz)
Clock Frequency
(MHz)
(720 X 400)
31.469
70.087
28.322
Type
Amorphous active matrix super TFT LCD
VGA
(640 X 480)
31.469
59.940
25.175
Screen Size
38.1cm (Diagonal)
VGA
(640 X 480)
37.500
75.000
31.500
Maximum Resolution
1024 X 768 @ 75 Hz
SVGA (800 X 600)
37.900
60.320
40.000
Pixel Range
0.297 mm X 0.297 mm
SVGA (800 X 600)
46.875
75.000
49.500
XGA (1024 X 768)
16.7M Color
60.004
65.000
Display Colors
48.363
XGA (1024 X 768)
60.023
75.029
78.750
Contrast Ratio
350 : 1
MAC (640 X 480)
35.000
66.667
30.240
Viewing Angle
60째 / 60째 / 40째 / 60째 (Left / Right / Up / Down)
MAC (832 X 624)
49.726
74.551
57.284
Response Time
25 msec
Luminance
250 cd/m
Resolution
VGA
Model
LCD
Panel
H550(B17CF
Synchro Horizontal Frequency
nization Vertical Frequency
Video
Input
Assignment
Pin No.
Assignment
Red Video
Green Video
10
5V Input
Ground
Blue Video
N.C
Ground
11
12
13
Ground
SDA
H.Sync
Red Video Ground
Green Video Ground
14
15
V.Sync
SCL
Blue Video Ground
18 - English
Control key Front Part
Power Supply
Wall Mount
Safety Standard
10
11
15
Analog RGB (0.714 Vpp) 75 ohm
40W
Under 1W
MUTE MENU / EXIT, SELECT/AUTO, POWER,
-/
75 Hz (Max.)
Synchronous Signal Mode H, V Separate TTL Sync,
Maximum
Power
Consumption Power Saving Mode
Pin assignment table D-Sub
Mini 15pin connector
Pin No.
Video Signal
60kHz (Max.)
, +/ , VOL
90/240V (50~60 Hz), 0.5 A
VESA Standard
UL, CE, TUV, CB
Safety
Standard EMI
& EMI
Low Radiation
MPR-II
Dimension Size and Weight
352 156 369 / 4.1kg
FCC,RRL
15pin D-Sub
English - 19
Troubleshooting
Power LED is dark.
No picture.
Check the power connection.
(Refer to page 4)
Color is irregular.
Adjust COLOR at User Mode in OSD Color
Menu.
OSD, "check cable."
is displayed on the
screen.
Check the computer power is on.
Double images or
'ghosts'.
Check the resolution and frequency of
computer and video card, and set up
again in reference to the current monitor
mode and standard signal mode table.
Message, "No cable."
is displayed on the
screen.
Check the signal cable between monitor
and computer. (Refer to page 4)
Screen looks to be run
down.
Perform Auto_config.
Picture is dark.
Picture is biased or cut
or too wide.
Screen is not clear.
Display is unstable and
trembling.
20 - English
Remove attaches to the signal line
(Video extension cable and others)
and switch on.
Perform Auto-config.
Adjust clock and PHASE.
Check the resolution and frequency of
computer and video card, and set up
again refer to the current monitor
mode and standard signal mode table.
Power LED turns into
Green blinking.
NO SOUND
Adjust COLOR at User Mode in OSD Color
Menu.
Perform Auto-Config.
Monitor is in DPMS mode.
Check the voice signal connection code or
adjust volume
English - 21
Warning
To prevent damage or loss, please read this warning carefully.
When connecting/disconnecting the plug, pull out
the plug itself, and never pull the cord to prevent fire
caused by short.
To prevent electric shock, do not connect/disconnect the plug with wet hand.
If you see smoke or smell something burning, stop
using the unit, switch off the power, pull out the plug,
and then contact your local service station.
To prevent fire, do not connect a large number of
equipments in a single line.
To prevent fire and electric shock, pull out the plug in
case of thunder and lightening.
To prevent fire and electric shock, do not try to take
the monitor apart or repair it yourself. Contact your
local service station or customer service center for
inspection, modification or repair.
22 - English

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2002:12:28 12:00:17
Producer                        : Acrobat Distiller 4.0.5  for Macintosh
Author                          : Á¤
Creator                         : QuarkXPress: PSPrinter 8.3.1
Title                           : Ç¥ÁöH550_ENG
Modify Date                     : 2003:01:23 15:23:30+09:00
Page Count                      : 13

EXIF Metadata provided by EXIF.tools