Hansol LCD B19BF 19" LCD MONITER User Manual MANUAL

Hansol LCD Inc. 19" LCD MONITER MANUAL

Contents

MANUAL

Printed in KoreaPart No. 942205010002- 01Printed on the recyclable paperTFT-LCD Color MonitorUSER'S MANUAL19
Parts 3Connection to Signal Source 4the range of control Angle 5Installing Monitor Driver 6Name and Function of Front 8Power Management Feature 10Adjusting OSD 11Hot Key 19Standard Signal Table 19Specification 20Troubleshooting 22Warning 24Table of ContentsINFORMATION TO USER :This equipment has been tested and found to comply with the limits of a ClassB digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses and canradiate radio frequency energy and,if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation; if this equipment does cause harmful interference to radio ortelevision reception, which can be determined by determined by turning theequipment off and on, the user is encouraged to try to crrent the interference byone or more of the fllowing measures:1. Reorient/Relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit differencefrom that to which the recerver is connected.4. Consult the dealer or an experienced radio/TV technician for help.CAUTIONChanges or modifications not expressly approved by themanufacturer responsible for compliance could void the user's authority to operate the equipmentENERGY STARAs an ENERGY STAR partner, Hansol Electronics Inc. has determined that this product meets energy Star guidelines for energy efficiency.
English - 32 - EnglishPartsLCD MonitorPlace the monitor to face the user and then adjust the monitor angle.Take a break (for about 10 minutes) at every hour during the work with monitor. Refer to the following figure to take the correct posture. about 50cmLook down the monitorbelow the horizon.Relax shoulders and arms, and sit back on the chair.Adjust the monitor to prevent reflection.Adjust the monitor stand to acquire required angle.Keep feet flat on the ground.Maintain the arms horizontallyand place hands softly on the keyboard.Good Posture GuideUser's Manual /Warranty CardSignal Cable (Analog) AC Power CableInstallation DisketteStereo Cable(Option)Signal Cable (DVI)
English - 54 - EnglishConnection to Signal Source 1. Use 220 V or 110 V. (Free Voltage)2. Connect monitor and Signal Source via Signal cable3. Power on the monitor and computer.4. Connection is finished.General For MacintoshAdapter for Macintosh (Optional)Refer to the table on the rear side ofthe optional Macintosh adapter andadjust DIP switch by the resolution. T he range of control Angle< Power source connection > < Signal cable connection> Basic Connection How to Adjust the StandForward 5DefaultBackward 33Port for AC power cablePort forAudio cable fromaudio source.Port for Head Phone or External SpeakerPort for signal cable from DVI signal source.Kensington LockPort for signal cable from analog signal source.
English - 76 - EnglishClick 'Finish'.Click 'Next>'.Click 'Advanced..'. Click 'Next>'.Click 'Monitor'. Click 'Change..'.Click 'Display a list of all...'.Click 'Next>'.Click 'Have Disk..'.Select the driver and click 'OK'. Click 'Next>'.3. Select "Exit" if the monitor model is changed, and then reboot the Windows.Installing Monitor Driver1. Insert the Diskette to the Floppy Diskette driver. 2. Double-click "Install.exe". 3. Select the model and click "OK" button.4. Select inf file, and then click "OK" button.5. Click "Exit" button to close the installation.Automatic InstallationManual Installation1. Insert the Diskette to the Floppy Diskette driver.2. Click 'My Computer' and follow the procedure below.Click 'Control Panel'. Click 'Display'. Click 'Settings'.Run (Click) "Install" at Floppy Diskette driver and select the model name toset the optimum display in Window 95, 98 or 2000, XP.Use the Driver provided.
+/ -/English - 98 - EnglishPower buttonPower button is located in the lower center of the Front Bezel.You can push the button to turn on/off the power.Power Indicating LEDDark : Power off Green : Normal modeGreen blinking : DPMS mode or Check Signal Cable mode.On Screen Display (OSD) Function ButtonOSD buttons on the front of bezel perform the following functions.SOURCE: Press this button to change Analog/DVI display.MENU/EXIT : Press this button to display menus. if you press this button when OSD is displayed, you can switch display to the previous menu and exit menu.SELECT/ AUTO : Press this button, when OSD is not displayed, to performautomatic setting. When OSD is displayed, You can select icons.POWER : Power button.: By pressing these button when OSD is displayed, You can move cursor into the menus which you want.After press the SELECT button, you can change gauge level or select submenus.When OSD is not displayed, you can adjust brightness or contrast.VOLUME / MUTE : Press this button for volume control. when control is displayed,You can control mute by pressing this buttonName and Function of Front Front panel FunctionsSELECT/AUTO BUTTONMENU/EXIT BUTTONSOURCE BUTTONVOL / MUTEBUTTON/ +BUTTONPOWER BUTTON/ - BUTTON
English - 1110 - EnglishNo image is displayed with Green blinking.Monitor is in power saving mode.Use mouse or keyboard to release power saving mode.No image is displayed without LED on.Power cable plug must be pulled out.Check the power plug on monitor and on the wall."Out of range" displayed on the screen.This message is displayed when the signal from video card exceeds themaximum frequency of the monitor. Readjust resolution and frequency inaccordance with the monitor capacity. (Refer to Standard Signal Table)Power Management FeatureThe monitor is equipped with a power saving circuit that confirms to the world-standard Display Power Manager Signalling(DPMS) mode of Video Electronics Standard Association (VESA).The power management feature requires that the video card of thecomputer should support DPMS function. Status LED Sign Power ConsumptionNormal mode Green ON Normal PowerDPMS mode Green Blinking 1W or Below(Analog)/3.5W or Below(DVI)1W or Below(Analog)/3.5W or Below(DVI)DPMS with Audio (Option)Mute ONMute OFF 10W or BelowAdjusting OSDDigital InputAnalog Input1. Use to move Digital input ICON.2. Press SELECT button to select DVI display.SELECTInput SourceMENU1. Press the MENU button to access main menu.2. Use to move Input source ICON.3. Press SELECT button into the submenu.SELECTSELECT1. Use to move Analog input ICON.2. Press SELECT button to select Analog display.
English - 1312 - EnglishHorizontal PositionSELECT1. Use to move H-Position ICON.2. Press SELECT button to select it.3. Use to adjust display left or right.ImageMENU SELECT1. Press the MENU button to access main menu.2. Use to move Image ICON.3. Press SELECT button into the submenu.According to the characteristic of video card,control range can be changed.1. Use to move V-Position ICON.2. Press SELECT button to select it.3. Use to adjust display upward or downward.SELECTVertical PositionAccording to the characteristic of video card,control range can be changed.BrightnessContrast1. Use to move Brightness ICON.2. Press SELECT button to select it.3. Use to adjust the brightness. SELECTBrightness &ContrastMENU1. Press the MENU button to access main menu.2. Use to move Brightness and Contrast ICON.3. Press SELECT button into the submenu.SELECTSELECT1. Use to move Contrast ICON.2. Press SELECT button to select it.3. Use to adjust the contrast.
English - 1514 - EnglishUser Color1. Use to move User color ICON.2. Press SELECT button to select it.3. Use to Shift the Color what you want.4. Use select button to select it.5. Use to increase or decrease each color.6. Press the menu button to return previous state.1. Use to select the 6500K, and 9300K.2. Press the Menu button to return previous state.6500K : Reddish white 9300K : Bluish whiteMENUMENUSELECTPreset Color1. Press MENU button to access main menu.2. Use to move Specal ICON.3. Press SELECT button into the submenu.MENU SELECTSpecial1. Press to move Clock Phase ICON.2. Use SELECT button to select it.3. Use to correct fine trembling or Video noise.1. Use to move Clock ICON.2. Press SELECT button to select it.3. Press orto remove vertical noise.( Adjusting clock phase is required after the adjustment of clock.) SELECTSELECTClockClock Phase1. Press MENU button to access main menu.2. Use to move Color ICON.3. Press SELECT button into the submenu.MENU SELECTColor
English - 1716 - English1. Use to move Language ICON.2. Press SELECT button to select it.3. Use to select language.MENU SELECTLanguage1. Use to move OSD V-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD upward or downward.SELECTOSD V-Position1. Use to move OSD H-Position ICON.2. Press SELECT button to select it.3. Use to adjust OSD left or right.SELECTOSD H-Position1. Use to move OSD Time ICON.2. Press SELECT button to select it.3. Use to adjust OSD display time.OSD TimeSELECT1. Use to move the Information ICON.2. Press SELECT button to select it.MENUAuto-ConfigInformation1. Use to move the Factory Reset ICON.2. Press SELECT button to return to default setting.Auto-ConfigFactory ResetSELECTSELECTYou can know display informationAccoding to the characteristic of video card, display information can be incorrect
English - 1918 - English1. Use to move Sound ICON.2. Press SELECT button to select it.3. Use to control volume.4. Press MENU button to return previous state.MENUAuto-ConfigSound (Option)SELECT orVOL BUTTON1. When change DVI display into Analog display, select source button located in the left. Analog display will be showed after Analog input message.2. When change Analog display into DVI display, select source button located in the left. DVI display will be showed after DVI input message.3. No signal input message will be displayed when video card output is not mated with monitor source.Standard Signal TableVGA (720 X 400)VGA (640 X 480)VGA (640 X 480)SVGA (800 X 600)SVGA (800 X 600)XGA (1024 X 768)XGA (1024 X 768)SXGA (1280 X 1024)SXGA (1280 X 1024)MAC (640 X 480)MAC (832 X 624)MAC (1152 X 870)31.46931.46937.50037.90046.87548.36360.02363.98179.97635.00049.72668.68170.08759.94075.00060.32075.00060.00475.02960.02075.02566.66774.55175.06228.32225.17531.50040.00049.50065.00078.750108.000135.00030.24057.284100.000ResolutionHorizontal Frequency (KHz)Vertical Frequency(Hz) Clock Frequency(MHz)
English - 2120 - EnglishSpecificationType Amorphous active matrix super TFT LCDScreen Size 48.3cm (Diagonal)Maximum Resolution1280 X 1024 @ 75 HzPixel Range0.294 mm X 0.294 mmDisplay Colors 16.7M ColorContrast Ratio 500 : 1Viewing Angle 85° / 85° / 85° / 85° (Left / Right / Up / Down)Response Time 25 msecLuminance 250 cd/mHorizontal Frequency 79.9kHz (Max.)Vertical Frequency 75 Hz (Max.)Video Signal Analog RGB (0.714Vpp) 75 ohm/ Digital(TMDS)Sync Type H, V Separate TTL Sync, Maximum 48WPower Saving Mode Under 1 W(Analog)/Under 3.5 W(DVI)SOURCE MENU / EXIT, AUTO/SELECT, POWER,, VOL/MUTENormal1W/Ch Max 1.5W/Ch Input : 100-240Vac (50/60 Hz), 0.6AVESA StandardSafety Standard UL, CE, TUV, CBEMI FCC,RRLLow Radiation MPR-IISize and Weight418 200 437.2 / 6.3kgLCDPanelSynchronizationModel H950 (B19AFVideoInputAudioOutputPower ConsumptionControl keyFront Part SafetyStandard& EMIDimensionPower Supply Wall Mount, +/-/Pin assignment table D-SubMini 15pin connectorPin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment18D1D217 24 D3 D491511 1561015pin D-SubPin No. Assignment Pin No. Assignment 1 Red Video 9 5V Input2 Green Video 10 Ground3 Blue Video 11 Ground4 N.C 12 SDA5 Ground 13 H.Sync6 Red Video Ground 14 V.Sync7 Green Video Ground 15 SCL 8 Blue Video Ground
English - 2322 - EnglishCheck the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table.Double images or'ghosts'.Perform Auto-Config.Adjust COLOR at User Mode in OSD Color Menu.Picture is dark.Picture is biased or cutor too wide.Monitor is in DPMS mode.Power LED turns intoGreen blinking.Check the voice signal connection code or adjust volumeNO SOUNDAdjust COLOR at User Mode in OSD Color Menu.Color is irregular.TroubleshootingCheck the power connection. (Refer to page 4)Power LED is dark.No picture.Perform Auto_config.Check the computer power is on.OSD, "check signal."is displayed on thescreen.Check the signal cable between monitor and computer. (Refer to page 4)Message, "check cable."is displayed on thescreen.Screen looks to be rundown.Screen is not clear.Check the resolution and frequency of computer and video card, and set up again refer to the current monitor mode and standard signal mode table.Display is unstable andtrembling.Remove attaches to the signal line(Video extension cable and others) and switch on.Perform Auto-config.Adjust clock and PHASE.
24 - EnglishWarningTo prevent damage or loss, please read this warning carefully.When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short.To prevent electric shock, do not connect/dis-connect the plug with wet hand.To prevent fire, do not connect a large number ofequipments in a single line.To prevent fire and electric shock, pull out the plug incase of thunder and lightening.To prevent fire and electric shock, do not try to takethe monitor apart or repair it yourself. Contact yourlocal service station or customer service center forinspection, modification or repair.If you see smoke or smell something burning, stopusing the unit, switch off the power, pull out the plug,and then contact your local service station.

Navigation menu