Hansong DYN Wireless Speaker User Manual
Hansong(Nanjing) Technology Ltd. Wireless Speaker Users Manual
Hansong >
Users Manual
Xeo 10/20/30 Owner’s manual Hello Welcome to Dynaudio Xeo. We’ve taken care of the tech; you take care of the music. This is Xeo 10 10 10 11 11 11 11 12 13 13 14 14 15 15 15 15 16 16 16 17 17 Introduction Important safety instructions Warning Xeo 10/20/30 speakers Remote control battery Unpacking Removing the protection cap Packaging material Disposal Scope of delivery Connections and control elements Elements on the rear panel Buttons on top of the cabinet (Xeo 10) Remote control Connecting and setting up Positioning and connecting to mains voltage Cloth cover General settings Connecting sources directly Connecting a Bluetooth device Connecting sources via Hub or Connect Operation Switching on 17 17 18 18 19 21 22 22 22 22 23 25 26 27 27 28 30 30 31 31 33 Playback of connected sources Playback of a Bluetooth device Fixing the volume Standby Status LEDs on the front Malfunctions Accessories Desk stand Wall bracket VESA 100 bracket (Xeo 10/20) Setting up Connection options Division into audio zones Components of the Xeo system The Xeo system Combination examples Declaration of Conformity (EU only) Reminding (USA and Canada only) IC NOTICE MPE Reminding Technical data Dynaudio Xeo 10/20/30 Thank you Introduction for choosing Dynaudio Xeo. Xeo combines the latest wireless technology with impressive sound quality and makes listening to music truly convenient and easy. The next few pages contain important information on connecting the system and its operation to ensure perfect function and the best-possible sound quality. We hope you have a great time listening to your favourite music. Dynaudio About this product The active Xeo 10/20/30 speakers are equipped with powerful integrated amplifiers and allow for the direct connection of various analog and digital audio sources. A Bluetooth interface enables the operation of Bluetooth devices and plays them back in optimal sound quality. Optional components like Xeo Hub or Dynaudio Connect enable setting up a wireless multiroom system without any restrictions to the highest sound quality. The speakers can be fully controlled with a remote control. The operational state of the system is indicated by two LEDs on the front. About this manual This manual describes the operation of the Xeo 10/20/30 speakers. Information about the optional Xeo modules (Hub, Connect, Extender, Link) can be found in the Owner´s manual provided with these modules. Dynaudio Xeo 10/20/30 Xeo The quintessential wireless hi-fi system Important safety instructions Important safety instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. USA and Canada only: A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the apparatus. Only use attachments/accessories specified by the manufacturer. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus. To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle. The mains plug of the power supply cord shall remain readily operable. Dynaudio Xeo 10/20/30 Warning Warning / Unpacking Xeo 10/20/30 speakers RISK OF ELECTRIC SHOCK! DO NOT OPEN! If the speakers are connected to the mains voltage, a dangerous electrical voltage is present inside the speakers. ►► Use the supplied power cable to connect the speakers to the mains voltage. Make sure that the power supply cable is not damaged; replace it with a new one if it has been damaged. ►► To reduce the risk of electric shock, do not remove the back panel and never open the speaker housing. Do not expose the speakers to rain or moisture. No user serviceable parts inside. Refer servicing to qualified personnel. ►► Do not operate defective speakers and disconnect defective speakers from the mains voltage. Please contact your Dynaudio Xeo distributor if you have any problems. Distributor addresses can be found on the Internet at dynaudio.com. Remote control battery DANGER OF EXPLOSION Danger of explosion if battery is incorrectly replaced. ►► Replace only with the same or equivalent type. CHEMICAL BURN HAZARD If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. ►► If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 10 Unpacking After unpacking, make sure the system is complete and check the device and all accessories for transport damage. Transport damage may be expected if the packaging is already severely harmed. Do not attempt to start up a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio Xeo distributor. Distributor addresses can be found on the Internet at dynaudio.com. Removing the protection cap The tweeter is protected by a cap to prevent damage during transport and unpacking. ►► After you have unpacked the speaker, remove the cap by just pulling it straight out. Packaging material The packaging has been designed so that it may be reused as long as it has not been damaged during transport. Keep the packaging and use the original packaging for all further transport. Disposal Disposal of used electrical and electronic equipment (applicable in European countries with separate collection systems for this equipment) This symbol on the product or its packaging indicates that the product must not be treated as household waste. Instead, it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials helps to conserve natural resources. For more detailed information on recycling this product, please contact your local authority, community waste disposal office, or the shop where you purchased the product. 11 Dynaudio Xeo 10/20/30 Scope of delivery / Connections and control elements Scope of delivery 2 Xeo 10/20/30 speakers 2 Xeo 10/20/30 speaker cloth covers 1 Xeo 10/20/30 remote control 2 power cables (country-specific version, length: 2.5 m) 1 stereo cable (RCA – RCA, length: 1.5 m) (Xeo 10 only) 1 optical cable (Toslink – Toslink, length: 1.5 m) (Xeo 10 only) 1 stereo cable mini jack (3.5 mm – 3.5 mm, length: 1.5 m) (Xeo 10 only) Connections and control elements This section describes the connections and control elements. Please contact your Dynaudio Xeo distributor if you have any problems with connection and start-up. Distributor addresses can be found on the Internet at dynaudio.com. Elements on the rear panel The Xeo 10/20/30 set consists of a master and a slave unit. The master unit carries the audio input interfaces. 1 Xeo first time setup manual (quick guide for installation, not shown) II OFF Line Opt Coax USB VOLUME Line Opt Neutral Blue Aux DIRECT HUB Aux In Line In Optical In Service Mains socket Sound adjustment (depending on the position of the speakers) • Neutral = with free-standing placement • Wall = if placed near a wall • Corner = if placed in a corner Speaker placement • Left = left speaker for stereo mode • Right = right speaker for stereo mode B: Speaker ID/Zone Selection of audio zones: Speakers assigned to different zones can be controlled separately via the remote control. The zones are identified as Red, Green, and Blue. C: Aux In: To connect an analog audio source to the speaker via mini jack. Line In To connect an analog audio source to the speaker via RCA. D: Optical In (Toslink):To connect a digital audio source to the speaker. E: USB In For firmware update only. F: Mains socket To connect the speaker to the mains voltage. Green Right Red Left Wall Corner Zone ON Speaker Position MUTE A: Speaker position II (master unit only) 12 13 Dynaudio Xeo 10/20/30 Connections and control elements / Connecting and setting up Buttons on top of the cabinet (Xeo 10) Speaker on/off to switch on the speakers. The Xeo 10 will scan the inputs for a ►► Press signal. to switch off the speakers. ►► Press and hold Input selection to jump to another input. ►► When switched on, press Volume control Bluetooth pairing or to raise or lower the ►► Press and hold both and ►► Press volume level. Press and hold for start pairing (see page 16). faster adjustment. to Connecting and setting up Positioning and connecting to mains voltage ►► Position the speaker in the desired location. – Do not expose the speaker to direct sunlight, heat, or moisture. – Do not place the speaker near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields. ►► Use the power cable to connect the speaker to the mains voltage. Tip Xeo 10: • For easier access, the plate at the bottom of the cabinet can be removed. Use a coin or screwdriver to loosen the screw and attach the plate after connecting the power cable. Cloth cover The cloth cover has been designed so it does not influence the sound dispersion of the speaker. It is attached to the housing with magnets and may be removed if needed. Remote control Commands will always apply to both of the speakers. General settings MUTE ON OFF MUTE Muting the speakers to mute or unmute the ►► Press speakers. ON/OFF Reset Speaker on/off to switch on the speakers. ►► Press for at least 5 seconds to ►► Press for standby mode. Press ►► Press reset the speakers to the factory for at least 5 seconds to put the settings. speakers in sleep mode. VOLUME Volume control or to raise or lower the volume level. ►► Press INPUT Signal source ►► Press a button to select the respective signal source. selects a Bluetooth device or ►► Hub/Connect. Line Opt Coax USB VOLUME Line Opt Aux DIRECT HUB Controls Press to control most Bluetooth 4.1 compliant devices: 14 Fixing the volume for at least 2 seconds to set ►► Press a high volume for the speakers (see page 18). ►► In stereo mode: – Select Left operating mode for the left speaker. – Select Right operating mode for the right speaker. ►► Set the speaker position switch that best describes the speakers´ need for acoustic compensation. – Neutral = with free-standing placement – Wall = if placed near a wall – Corner = if placed in a corner ►► Select the Red, Green, or Blue zone. Select the same zone for the right and left speakers (for additional information about the audio zones, see page 26). Bluetooth pairing for at least 5 seconds to ►► Press enter pairing mode. = backward, = forward = play or pause, 15 Dynaudio Xeo 10/20/30 Connecting and setting up / Operation Operation Connecting sources directly Switching on ►► Connect your source cables to one or more of the audio inputs Aux , Line , Opt of the master speaker (see „Connection options“ on page 13). After it is turned on, the speaker automatically searches for an audio signal and then plays it back immediately. If several signal sources are active, one of the signal sources will be played back. To switch the speakers on from standby mode: ►► Press on top of one of the speakers (Xeo 10) or point the remote control at a speaker and press . – The speakers will automatically search for an active audio signal. If found, the signal will be output (autoplay function). – If there is no input signal, the speakers will continue scanning the inputs for the next 20 minutes and enter sleep mode. Tip (Xeo 10): • For easier access, the plate at the bottom of the cabinet can be removed. Use a coin or screwdriver to loosen the screw and attach the plate after connecting the power cable. If there is no input signal, the speakers will go into standby mode after a certain period. Playback of connected sources Connecting a Bluetooth device 1. To begin Bluetooth pairing, press and hold both and buttons on either one of your speakers (Xeo 10). Alternatively, hold Bluetooth on remote for 5 seconds. – Once available for pairing, the status indicator will blink white and it will be available for pairing for one minute. 2. Go to settings on your device, find the Bluetooth sub-menu, and simply pair your device with your Xeo speaker by selecting Red, Green, or Blue. The speaker will store your pairing. Connecting sources via Hub or Connect Xeo Hub and Dynaudio Connect are optional components that allow you to connect analog and digital sources and are linked with your Xeo speaker via a wireless, lossless signal. For further information about the complete Xeo system, please see „The Xeo system“ on page 27. 16 ►► Once you have connected your Xeo speaker with a direct input, simply choose your desired source on the remote. – The speakers will automatically detect the signal and start playback. Master and slave speaker will connect wirelessly if set in the same zone. – If no signal is applied to either input, the speakers will continue scanning the inputs for the next 20 minutes and enter sleep mode. Playback of a Bluetooth device Once you have paired your device with your Xeo 10/20/30, you can connect by choosing the Xeo 10/20/30 from your list of Bluetooth devices. ►► Select Bluetooth on the remote control and press play on your Bluetooth device. Disconnect ►► Press and hold directly. to disconnect a connected device or disconnect from the device 17 Fixing the volume Dynaudio Xeo 10/20/30 Fixing the volume You can set the speaker to a higher volume using the function to fix the volume. This setting also remains in effect in standby mode. If a signal source is connected to the Xeo 10/20/30 with its own volume control, you have the option to change the output volume across a broad range with the signal source. To fix the volume: ►► Point the remote control at a speaker and press fixing, press one of the two volume buttons. for at least 2 seconds. To undo Standby To switch speakers to sleep mode: ►► Point the remote control at a speaker and press or press on top of one of the speakers. – The speakers will enter sleep mode. – The speakers also enter sleep mode if there is no audio signal for 20 minutes. – In this mode, the wireless network is active and all connected units remain synchronized. – Sleep mode power consumption is <2 W. To switch speakers to low-power standby mode: ►► Press and hold on the remote control for at least 5 seconds. – The speakers go to low-power standby mode. – In this mode, the wireless network is disabled and the speakers are not connected to each other. – Low-power standby mode power consumption is <0.5 W. Status LEDs on the front The two LEDs in the upper left corner of the cabinet front indicate the operational state of the speakers and system with various colours and blinking functions. On-state Illuminated in blue The speaker is switched on, connected to a Hub or Connect, and an audio signal is played back. On-state Slow blinking in blue The speaker is switched on, connected to a Hub or Connect, but an audio signal cannot be found. On-state Illuminated in purple The speaker is switched on, connected to a local input, and an audio signal is played back. On-state Slow blinking in purple The speaker is switched on, connected to a local input, but an audio signal cannot be found. Connection Slow blinking in red Search Fast blinking in blue for 20 min Synchronization/ Fast blinking in red for 10 s Connection Blue LED is turned off for 0.2 s Searching for an active input. System synchronization during no transmitter2)/master connection. New transmitter2) ID, transmitter2) input, or direct input is selected. Illuminated in red for 5 s Receiver mode is changing. Illuminated in white Bluetooth connection is established. Slow blinking in white Speaker is in pairing mode. Firmware loading White LED: slow to fast blinking during the load sequence, Red LED: illuminated Firmware is being loaded. Volume Fast blinking in blue Volume is being adjusted. Mute Fading in and out To turn off auto standby: ►► Press and hold Opt on the remote control for at least 5 seconds. There is no active transmitter2)/master or no connection possible. Off-state Illuminated dimly in red 1) Speaker is muted. Speaker is in standby mode. depending on the resolution of the audio source, 2) Hub, Connect, mobile device, etc. LED blinking code off 18 Illuminated in white Illuminated in a colour Slow blinking (1 or 2 Hz) Fast blinking (3 or 4 Hz) 19 Dynaudio Xeo 10/20/30 Malfunctions Malfunctions Interruptions, clicking noises, or other audible interference when playing music is usually not caused by radio transmission in the Xeo system. Often, other external causes influence the transmission quality. Below are a few tips for improving transmission quality: 1. Position all radio transmitters and receivers away from each other. WLAN devices, radio receivers, and radio systems may influence each other if they are too close together. Test out various locations for each device. 2. Switch off the automatic search function in WLAN devices. WLAN devices and other radio systems permanently scan for available frequencies, thus sending signals that could disrupt other radio systems. This automatic search function can usually be switched off. 3. Xeo technology radio signals can, of course, transmit through walls. However, walls may consist of very different materials, such as wood fibreboard, stone, or even steel. The walls may also contain complex cable installations for electrics, phones, TVs, and radios, as well as water pipes and air shafts. These can divert radio signals. This is why you should test different locations for the Xeo Hub, Extender, and Link and favour the most direct radio path between the Xeo components. 4. Some electrical devices, such as microwaves, generate strong electromagnetic fields that could disrupt radio systems. Do not operate such electrical devices near Xeo components. You can ask your Dynaudio Xeo distributor for assistance at any time Or go to dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at dynaudio.com/xeo 20 21 Dynaudio Xeo 10/20/30 Accessories Accessories / Setting up Accessories (Xeo 10) A desk stand or wall brackets extend the range of applications of your Xeo 10 speakers. For further information, please see the website at dynaudio.com or contact your Dynaudio distributor. Distributor addresses can also be found at dynaudio.com VESA 100 bracket (Xeo 10/20) VESA is a standard for wall brackets developed by the Video Electronics Standards Association. The Xeo 10 and Xeo 20 speakers allow you to mount brackets according to the VESA 100 standard. This means that the screws on the back plate are spaced 100 mm apart. Desk stand The Dynaudio desk stand for Xeo 10 is an elegantly designed stand for placing the speakers on a desk or shelf. A installation instruction is provided with the stand. Wall bracket The wall bracket allows you to mount the Xeo 10 speakers on the wall. 22 To mount a VESA 100 bracket (Xeo 10): 1. Loosen the four screws (Torx type) and unmount the back plate. 2. Keep the back plate for future use. Follow the instructions provided with the bracket you want to mount. Setting up Spikes with pointed ends Xeo 30 floor-standing speakers are delivered with spikes for permanent installation on the floor. The pointed ends of the spikes may result in injuries and damage delicate floors. ►► Pay attention that you do not injure yourself with the spikes. ►► We recommend inserting the spikes in aluminium feet if you have delicate floors, such as parquet or laminate. ►► Position the speaker in the desired location. – Do not expose the speakers to direct sunlight, heat, or moisture. – Do not place the speakers near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields. 23 Dynaudio Xeo 10/20/30 Connection options Connection options ►► Connect your signal source to the appropriate input on the Xeo 10/20/30 speaker. ►► Following table gives a selection of signal sources and options for connecting to the Xeo speaker. Your signal source Signal source output Xeo 10/20/30 input* Cable (source – Xeo 10/20/30) Notes Notebook, Mac™, PC Optical* Optical In Toslink – Toslink * If available Line out Line in RCA – RCA Headphones Aux in Jack 3.5 mm – 3.5 mm Headphones Aux in Jack 3.5 mm – 3.5 mm – – Smartphone, other portable devices Headphones Aux in Jack 3.5 mm – 3.5 mm Optical Optical In Toslink – Toslink PonoPlayer Jack Aux in Jack 3.5 mm – 3.5 mm – Docking station, network client, Sonos, Bluesound, etc. Line out Line in RCA – RCA * If available Optical* Optical In Toslink – Toslink Google Chromecast Audio Line out Aux in Jack 3.5 mm – 3.5 mm Optical Optical In Mini Toslink – Toslink Apple AirPort Express Optical Optical In Mini Toslink – Toslink – Apple TV* Optical Optical In Toslink – Toslink * up to 3rd generation Hard disk, network player, CD player Line out Line in RCA – RCA * If available Optical* Optical In Toslink – Toslink Analog radio, digital radio Line out Line in RCA – RCA Optical* Optical In Toslink – Toslink Analog record player Line out* Line in RCA – RCA * On phono preamplifier TV Headphones Aux in Jack 3.5 mm – 3.5 mm Select a variant. Line out Line in RCA – RCA Optical* Optical In Toslink – Toslink * If available Stereo preamplifier Pre-out, main out Line in RCA – RCA – Stereo power amplifier Tape out Line in RCA – RCA * Disconnect bridge Pre-out, main out* Line in RCA – RCA Second pre-out Line in RCA – RCA Subwoofer Analog output Line in RCA – RCA – AV receiver, AV processor Optical Optical In Toslink – Toslink – Pre-out, main out Line in RCA – RCA Astell&Kern 24 Select a variant. * If available 25 Dynaudio Xeo 10/20/30 Connection options The Xeo system Xeo consists of several high-quality components that are optimally matched. When combined, they can fulfil the most demanding requirements for a wireless multi-room and multi-source system. Division into audio zones Components of the Xeo system The Xeo speakers (as well as Xeo Link) can be assigned to audio zones using the Zone selector switch. All components assigned to the same zone can be operated together via the remote control. MUTE ON Xeo speakers The active Xeo speakers Xeo 10/20/30 receive the wireless signals from the Hub or Connect and play them back in optimal sound quality. In addition, the Xeo 10/20/30 can be connected directly to various audio sources. All speakers have an integrated amplifier and can be controlled with a remote control. Display elements indicate the operating state of the system and controls on the cabinet let you switch it on/off or change the volume without using the remote control. Xeo remote control The Xeo remote control can be used to turn the speakers on and off, change the volume, and select a Hub or Connect and its connected signal sources. Dynaudio Connect and Xeo Hub The Dynaudio Connect and Xeo Hub are the control centres for the Xeo system. Both offer a new level of wireless connectivity and convenience. Signal sources such as tuners, receivers, CD players, TVs, streaming clients, network players, MP3 players, or computers are connected to them. Signals are sent wirelessly and lossless to the connected Xeo or Focus XD speakers (or Xeo Link) where they are then played back. Xeo Extender The Xeo Extender extends the reception range of the Xeo Hub. As a result, Xeo speakers or other Xeo components can be operated further away from the Xeo Hub or Dynaudio Connect. Xeo Link The Xeo Link receives wireless signals from a Xeo Hub or Dynaudio Connect and outputs analog and digital signals from its connections. As a result, you can also connect active subwoofers, active speakers, or other components to the Xeo system. OFF Line Opt Coax USB VOLUME Line Opt Aux DIRECT HUB Blue Red Green Blue Red Green Blue Green Red Zone Green Zone Red Zone Blue The picture shows a possible zone configuration. 26 27 Dynaudio Xeo 10/20/30 Connection options Combination examples Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs. Direct wired: Analog/digital audio sources + Xeo 10/20/30 For extended range: Analog/digital audio sources + Hub or Connect + Extender + Xeo speaker Direct wireless: Bluetooth device (mobile phone, etc.) + Xeo 10/20/30 For additional speakers: Analog/digital audio sources + Hub or Connect + Xeo speaker plus + Link + active component (e.g. active subwoofer, active speakers, or power amplifier and passive speakers) With Hub or Connect: Analog/digital audio sources + Hub or Connect + Xeo speaker Note: The Extender and Link may also be combined. 28 29 Dynaudio Xeo 10/20/30 Connection options Declaration of Conformity (EU only) Dynaudio A/S hereby declares, that the product Dynaudio Xeo 10 / Xeo 20 / Xeo 30 is in conformity with the following directives: • 2001/95/EF (Product Safety) • 2014/53/EU (RE directive) • 2014/30/EU (EMC directive) • 2011/65/EU (ROHS directive) • 1275/2008 (ErP, Ecodesign directive) The Declaration of Conformity is available on the Internet at dynaudio.com/ support/manuals Reminding (USA and Canada only) A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à Ia section 15 des réglementations de Ia FCC. Le fonctionnement de l‘appareil est sujet aux deux conditions suivantes: 30 (1) cet appareil ne doit pas provoquer d‘interférences néfastes, et (2) cet appareil doit tolérer les interférences reçues, y compris celles qui risquent de provoquer un fonctionnement indésirable. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be IC NOTICE This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance 20 cm between the radiator and your body. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radioexempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. MPE Reminding (i) The device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) The maximum antenna gain permitted for devices in the bands 5250 – 5350 MHz and 5470 – 5725 MHz shall comply with the e.i.r.p. limit; and (ii1) The maximum antenna gain permitted for devices in the band 5725 – 5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. Cet équipement doit être installe et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. (i) Tout appareil destiné à la bande 5150 – 5250 MHz devra être exclusivement utilisé en intérieur a fin de réduire les risques de perturbations électromagnétiques gênantes sur les systèmes de satellite mobile dans un même canal. (ii) Les radars à forte puissance sont désignés comme les utilisateurs principaux (c‘est-à-dire qu‘ils sont prioritaires) des bandes 5250 – 5350 MHz et (iii) 5650 – 5850 MHz. IIs peuvent provoquer des perturbations électromagnétiques sur les appareils de type LELAN (réseau de communication local sans licence) ou les endommager. 31 Dynaudio Xeo 10/20/30 Technical data Technical data All Apple products are trademarks of Apple Inc. All Sony products are trademarks of Sony Electronics Inc. All Sonos products are trademarks of Sonos Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All Google products are trademarks of Google Inc. Other trademarks and trade names are those of their respective owners. An update to this manual may be necessary due to product improvements and new functions. The latest version of this manual is available on the Internet at dynaudio.com/support/manuals 30 32 Data Xeo 30 Xeo 20 Xeo 10 Analog inputs Mini-Jack, RCA stereo Mini-Jack, RCA stereo Mini-Jack, RCA stereo Digital inputs Toslink Toslink Toslink Wireless 24bit / 96kHz 24bit / 96kHz 24bit / 96kHz Frequency response (± 3 dB) 36Hz - 21kHz 40Hz - 21kHz 40Hz - 21kHz Box principle Bass Reflex Bass Reflex Bass Reflex Crossover 2½-way DSP based 2-way DSP Based 2-way DSP Based Crossover frequencies 200/4300Hz 4700Hz 5000Hz Woofer 2x14cm MSP 14cm MSP 14cm MSP Midrange Tweeter 28mm soft dome 28mm soft dome 28mm soft dome Amplifier power 3x65W 2x65W 2x65W AC power input 100V - 240V, 50/60Hz 100V - 240V, 50/60Hz 100V - 240V, 50/60Hz Standby power consumption <0.5W <0.5W <0.5W Maximum power consumption 165W 100W 100W Weight 13.4kg / 29.5lbs 6.2kg / 13.7lbs 4kg / 8.8lb Dimensions (WxHxD) 180x825x246mm 180x320x257mm 173x255x154mm 7.1x32.5x9.7in 7.1x12.6x10.1in 6.8x10x6.1in 228x852x275mm 180x320x265mm 173x255x164mm 9.0x33.5x10.8in 7.1x12.6x10.4in 6.8x10x6.5in Dimensions with feet/grille (WxHxD) 33 Xeo 10/20/30 Designed and engineered by Dynaudio Labs in Denmark Dynaudio A/S 8660 Skanderborg Denmark dynaudio.com Owner’s manual Xeo 10/20/30, EN - Item no. 45563101C. All text and image copyrights reserved. Subject to change without notice.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Language : en-GB XMP Toolkit : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36 Create Date : 2018:03:07 09:27:11+01:00 Metadata Date : 2018:03:07 09:27:15+01:00 Modify Date : 2018:03:07 09:27:15+01:00 Creator Tool : Adobe InDesign CC 13.0 (Macintosh) Instance ID : uuid:25c8b4f0-e3a6-2240-89f8-3088e8e93de6 Original Document ID : xmp.did:55a4cf20-db1d-43ea-ba1b-71540115afd7 Document ID : xmp.id:22b822e2-42eb-4e32-93fb-91cead0b4f57 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:eecee105-d1d9-44b3-9b0f-3631bd80b372 Derived From Document ID : xmp.did:05cb1d4c-698a-43dc-aab4-63e215598f81 Derived From Original Document ID: xmp.did:55a4cf20-db1d-43ea-ba1b-71540115afd7 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.0 (Macintosh) History Changed : / History When : 2018:03:07 09:27:11+01:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 18 Creator : Adobe InDesign CC 13.0 (Macintosh)EXIF Metadata provided by EXIF.tools