Hansong HSMPNP80 Wireless Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1241893
Application ID	D2qtYG9JLP0NQ+uvjvYNfw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.98kB (12238 bits)
Date Submitted	2010-02-15 00:00:00
Date Available	2010-02-15 00:00:00
Creation Date	2009-09-28 09:00:50
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2009-09-28 09:00:50
Document Title	Microsoft Word - User Manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	una

User Manual
The HS-DWAM80/PNP module is the wireless audio transceiver module. The module holds the
radio transceiver IC, the DARR80 digital audio baseband processor and associated components
and circuitry .
The HS-DWAM80/PNP platform can host many different applications ,requiring different external
components ,as a frame of reference ,for a simple stereo uni-directional audio link ,need to
external components are required.
Basic Features:
--Low latency ( configurable from 10……18ms )
--In-room or multi-room usage (point to multi-point is also supported )
--Bi-directional data channel
--Automatic frequency allocation
--Automatically controlled transmitter / receiver antenna spatial diversity minimizes fading and
multipath effects.
Pairing function :
all units in the same wireless audio network are provided with a 16bit network ID,shielding the
network from neighbor audio networks.
The HS-DWAM80/PNP is used for both the transmitter and receiver .The module is configured
either through the I2C interface ,through the EEPROM or through the optional microcontroller.
L e
b l reqirement:
if the FCC / IC identification number is not visible when the module is installed inside the host device, then
the outside of the device into which the module is installed must also display a label referring to the enclosed
module.This exterior label can use wording such as the following:
"Contains FCC ID:XCO-HSMPNP80 and IC:7756A-HSMPNP80."
Any similar wording that expresses the same meaning may be used.
REMINDING
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
The transmitter of this device has been designed to operate with the attached antennas, and
having a maximum gain of 1.5dBi. Antennas not identical as that or having a gain greater than
1.5dBi are strictly prohibited for use with this device. The required antenna impedance is 50
ohms. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that permitted for successful communication
MPE Reminding
1. The installed antennas must not be located in a manner that allows exposure of the general
population at a distance of less than 20cm.
2. Mount the antennas in a manner that prevents any personnel from entering the area within
20cm from the central position of the antenna.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2009:09:28 09:00:50+08:00
Create Date                     : 2009:09:28 09:00:50+08:00
Format                          : application/pdf
Title                           : Microsoft Word - User Manual.doc
Creator                         : una
Document ID                     : uuid:aaf31439-facd-45a4-8267-06f9fd8b9a60
Instance ID                     : uuid:eaaef037-b2e6-47c0-a194-46a6ed199cbd
Page Count                      : 2
Author                          : una

EXIF Metadata provided by EXIF.tools