Hantech WG100U ENZO WIRELESS NETWORK USB ADAPTER User Manual Uermanual FCC
Hantech Corporation ENZO WIRELESS NETWORK USB ADAPTER Uermanual FCC
Hantech >
USERS MANUAL
![](/img.php?id=966261&img=bg1.png)
WL0115 USER MANUAL
1
USB Wireless LAN Adapter User Manual
1 Install the driver
a Insert the installation CD into your CD-ROM driver, Double
click the icon to start setup
b Click Yes to go on
c It’s recommended to choice Optimize for performance mode
click next to go on
![](/img.php?id=966261&img=bg2.png)
WL0115 USER MANUAL
2
d
e Click Finish to end the setup
2 Plug in your usb wireless LAN adapter, it will be recognized
and auto installed. Just confirmed it like below:
3 Make infrastructure connection
Double click the icon in red circle
![](/img.php?id=966261&img=bg3.png)
WL0115 USER MANUAL
3
You will see:
You can click the button Rescan to find which AP is in range,
they will show on the window, choice one you want to
connect, and click the button connect, and click ok to finish
the connection operation.
An infrastructure connection is accomplished.
Note, please choose correct channel setting up to your law,
for example, ch13 is permitted in your country, and you set
your router at ch13, while you choose ch1-ch11 (default
setting), you will never find the AP, and you will have to
choose ch1-ch13 setting in Advanced page as below
![](/img.php?id=966261&img=bg4.png)
WL0115 USER MANUAL
4
4 Some help information in Rlink Wireless Utility
How to find out your IP address:
How to find out which a WIFI environment you are inside
![](/img.php?id=966261&img=bg5.png)
WL0115 USER MANUAL
5
5 Make Ad-Hoc mode connection
5.1 Make an Ad-Hoc SSID
Click Add
Choose Ad-hoc
![](/img.php?id=966261&img=bg6.png)
WL0115 USER MANUAL
6
Name your SSID and choose which channel you want to
take for the link
Activate the link
5.2 Setup static IP address for the Ad-Hoc link
At its property page, double click item Internet
Protocol (TCP/IP)
![](/img.php?id=966261&img=bg7.png)
WL0115 USER MANUAL
7
You will get
Fill the IP address blank, example as below:
![](/img.php?id=966261&img=bg8.png)
WL0115 USER MANUAL
8
Click ok to finish the setup
5.3 Ad-Hoc setup for one point accomplished
5.4 Setup another Ad-Hoc point as step A,B,C,D.
5.5 Ad-Hoc mode link accomplished. And you can visit
each other.
Note: To make an Ad-Hoc mode link, Do remember to
choice the same channel, its static IP address should be in
the same netsub, and the SSID should be the same too
6 Why it’s recommended to choose optimize for performance
mode while driver installation .
Choose this item, you will get turbo function that is powered by
Ralink Technology. With this technology, your will get higher TX
throughput.
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This device must be installed to provide a separation distance of at least 20 cm from all persons
and must not be collocated or operating in conjunction with any other antenna or transmitter.
NOTE: The manufacturer is not responsible for and radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.