Hanwha Techwin SSA-R2000V RFID Reader User Manual 20101005 v1 Appen

Samsung Techwin Co Ltd RFID Reader 20101005 v1 Appen

User manual

Download: Hanwha Techwin SSA-R2000V RFID Reader User Manual  20101005 v1   Appen
Mirror Download [FCC.gov]Hanwha Techwin SSA-R2000V RFID Reader User Manual  20101005 v1   Appen
Document ID1355643
Application IDpbZT7hGNQ8X6OzxB3kLlIg==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize31.82kB (397747 bits)
Date Submitted2010-10-07 00:00:00
Date Available2010-10-07 00:00:00
Creation Date2010-10-07 18:02:02
Producing SoftwareAcrobat Distiller 5.0.5 (Windows)
Document Lastmod2010-10-07 18:02:02
Document TitleUser Manual_20101005_v1 - Appen.PDF
Document CreatorPScript5.dll Version 5.2
Document Author: ltsai

RFID Reader
User Manual
SSA-R2000V
RFID Reader
User Manual
Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung
Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the
user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without
prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
• Sensory phenomenon that does not affect the performance or quality of the product (ex : working noise)
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates that dangerous voltage consisting a risk of electric shock is
present within this unit.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to
the product.
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the
controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the
power source and contact the service center. Continued use in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)
10.. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive
vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -30°C), or high humidity.
Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage
to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
English _ 3
SAFETY INFORMATION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
safety information
FCC Statement
Caution : Any changes or modifications in construction of this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, any cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
4_ safety information
contents
Features
What’s included
At a Glance
Cable Color Scheme
Cable Selection
INSTALLATION AND EXTERNAL
CONNECTION
10
11
Installation
Precautions on installation
External Connection
INITIALIZATION
12
Basic Operations
OUTPUT FORMAT
13
14
15
Wiegand Output
RS-232 Output
8 Bit Burst Output Format
TROUBLESHOOTING
16
Troubleshooting
PRODUCT SPECIFICATIONS
17
Product Specifications
CONTENTS
PRODUCT INTRODUCTION
12
13
16
17
English _ 5
product introduction
FEATURES
This model is an elegant-looking proximity reader that is featured by the capacitive touch-sensing keypad. The back-lighted
keypad is useful especially for night operation, and its epoxy adhesion and aluminium case relieve you of worries about the
rain or any other challenging weather conditions. This model permits user access through authentication of the presented
proximity card and personal identification number using the keypad. With its red, green and orange indicators as well as the
Piezo buzzer, this model is guaranteed to make a stable and correct operation.
◆ 125 KHz Proximity / PIN Reader
◆ PSK Modulation
◆ 26 bit Wiegand/RS-232 Data Output
◆ 8 Bit Burst Output Format supported
◆ Numeric Keypad with Backlighting for Night Operation
◆ Control of External LED Indicators
◆ Control of External Buzzer
◆ Tamper Switch
◆ Reverse Polarity Protection
◆ Weatherproof and Dustproof
WHAT’S INCLUDED
Check if the following items are included in the product package.
SSA-R2000V
Product
3.5 x 40mm Screws (x4)
3.5 x 25mm Screws (x4)
6 x 30mm Plastic Anchor (x4
Quick Guide
3mm Hex Wrench (x1)
6_ product introduction
CD Manual
AT A GLANCE
Front/Rear
PRODUCT INTRODUCTION
SSA-R2000V
LED
Displays the status of the system operation.
Keypad
Used to enter the ID/password.
Tamper Switch
A tamper switch to detect falling from the wall.
Connection Cable
Used to connect to the power source or I/O cable.
Buzzer
Piezo buzzer.
Fixing Hole
Fixing hole for wall-mounting.
English _ 7
product introduction
CABLE COLOR SCHEME
Item
Cable Color
Signal Line
Description
Red
DC +12V
Power (+12V)
Black
GND
Earth-grounding for power
Green
WIK_DATA0
Wiegand Data 0 Output Port
White
WIK_DATA1
Wiegand Data 1 Output Port
Purple
TX_OUT
΃΄ͣͤͣ͑͞΀ΦΥΡΦΥ͑΅ΖΣΞΚΟΒΝ
Orange
RS-232 GND
΃΄ͣͤͣ͑͞͸ΣΠΦΟΕΚΟΘ͑΅ΖΣΞΚΟΒΝ
Brown
NC
ͿΠΥ͑ΦΤΖΕ͟
Yellow
Green LED Control
͸ΣΖΖΟ͑ͽͶ͵͑ʹΠΟΥΣΠΝ͑ͺΟΡΦΥ͑
΅ΖΣΞΚΟΒΝ
Gray
Orange LED Control
΀ΣΒΟΘΖ͑ͽͶ͵͑ʹΠΟΥΣΠΝ͑ͺΟΡΦΥ͑
΅ΖΣΞΚΟΒΝ
Blue
Buzzer Control
BUZZER Control Input Port
Pink
Tamper COM
ʹ΀;͑΁ΠΣΥ͑ΠΗ͑΅ΒΞΡΖΣ͑΄ΨΚΥΔΙ
Light yellow
Tamper NC
Ϳʹ͑΁ΠΣΥ͑ΠΗ͑΅ΒΞΡΖΣ͑΄ΨΚΥΔΙ
Power
Output
Not used
Input
Tamper
CABLE SELECTION
Item
Cable Type
Power (DC12V)
Belden #9409, 18 AWG 2 Conductor, Unshielded
Card/PIN data (Wiegand)
Control Signal (LED,BUZZER)
TAMPER
Belden #9512, 22 AWG 4 Conductor, Shielded
RS-232 Cable
Belden #9829, 24 AWG 2-twisted pair, Shielded
8_ product introduction
Belden #9514, 22 AWG 8 Conductor, Shielded
installation and external connection
INSTALLATION
1. See [Figure 1] to drill 6-32” holes and 1/2” holes (totally 4) into the wall.
2. Tighten the four screws to secure the product to the wall.
60.30
79.60
4cm
100.80
4.35cm
6-32 or M3 Screws
8.7cm
00
91.50
Ø1.
86.50
1/2˝ hole
4.35cm
Ø1.
72.50
6.4cm
12.50
50
6-32 hole
69.10
54.50
36.50
26.23
Reader Module
Ø1.50
SSA-R2000V
18.50
Bezel
6.00
0.00
[Figure 1]
80.60
72.30
49.30
56.30
62.30
18.30
31.30
64.00
0.00
7.80
8.30
81.80
93.00
85.50
6-32 hole
40.30
Ø1.0
99.80
72.80
50.30
20.30
30.30
1.00
8.30
40.00
3mm Hex Wrench
[Figure 2]

English _ 9
INSTALLATION AND EXTERNAL CONNECTION
3. With the provided 3mm hex wrench, fix the outer case to the product.
installation and external connection
PRECAUTIONS ON INSTALLATION
IF INSTALLING ON A METAL WALL
If you install the reader on a metal wall, the read range may be reduced.
To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown
below.
Metal
Wall
Spacer
2000V
SSA-R
Reader
IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK
If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if
you present a card to one reader, the other reader may recognize the same card, meaning both readers read the
same card simultaneously.
To avoid this problem, keep at least 20cm of space between the two readers.
Minimum
20cm
#Reader 1
00V
SSA-R20
Minimum
20cm
#Reader 2
00V
SSA-R20
#Reader 1
BACK TO BACK

INSTALLATION
#Reader 2
00V
SSA-R20
SIDE BY SIDE

INSTALLATION
10_ installation and external connection
EXTERNAL CONNECTION
WIRING DIAGRAM
CONTROLLER
Green
Wiegand Data 1 Out
White
Tamper Switch Out(NC)
Light yellow
Tamper Switch Out(COM)
Pink
Buzzer Control In
Blue
RS-232(TX)
Purple
PC
RS-232(GND)
Orange
LED Control In(Green)
Yellow
LED Control In(Orange)
Gray
SSA-R2000V
Red
DC +12V
Black
GND
POWER
Category
Cable Wiring
Connect the DC+12V to the red line.
Power Supply Unit
Connect GND to the black line.
Connect the green line of the product to the Wiegand D0 input port of the controller.
Wiegand Connection
Connect the white line of the product to the Wiegand D1 input port of the controller.
LED Control
Enables you to turn on or off the LED indicators.
To control the green indicator, connect the yellow line; to control the orange indicator, connect the blue line
with white stripes, to the output port of the controller. (see page 12)
Buzzer Control
Enables you to turn on or off the buzzer.
To control the buzzer, connect the blue line to the controller’s output (relay). (see page 12)
Tamper Control
Connect the COM port (Pink line) of the product’s tamper switch to GND; connect the NC port (Light yellow)
of the tamper switch to the input port of the controller.
RS-232 Connection
Connect to the COM port of the PC. (Connect pin 2 of the DB-9 connector to the purple line; connect the
orange line to pin #5 of the DB-9 connector)
English _ 11
INSTALLATION AND EXTERNAL CONNECTION
SSA-R2000V
Wiegand Data 0 Out
initialization
BASIC OPERATIONS
Initial State (when the power is supplied)
When you apply power to the product, it will sound beep three times before entering Standby with the red indicator
turned on.
Using the card
ar
Present the card to the product until you hear a beep and the green indicator turns on.
The reader keeps the green indicator turned on while transferring the card data to the
controller. When it is done, the green indicator turns off and for receiving the next card,
the red indicator stays ON.
iŒ““
lzj
lzj
zzhTzYWWW
SSA-R2000V
Using the keypad
Hold down the keypad until you hear a beep. The reader transfers the keypad data to the controller.
As soon as you press the keypad, the orange indicator turns on, followed by the reader transferring the keypad data
to the controller. Then, only the red indicator turns on.
LED Control
You can control both green and orange indicators at will.
To control the green indicator, connect the green-indicator control line (yellow) to NO of the controller relay output,
and connect COM to GND. Set I/O of the controller; now you can control turning on/off the indicator.
You can turn on/off the indicators according to the I/O settings of the controller, which can be applied to various
situations. For more information about the I/O settings of the controller, refer to the user manual of the controller.
To control the orange indicator, connect the gray line to NO of the controller.
Buzzer Control
Connect the buzzer control input line (blue) to the NO port of the controller relay output, and GND to the COM port.
You can configure the I/O settings of the controller so that it beeps. If the product continues to beep, it means that
the buzzer control is working properly.
The controller can use the I/O settings to set the buzzer control so that it sounds an additional beep for authorized
or unauthorized access upon user authentication.
Furthermore, you can make various modifications according to the different I/O settings of the controller.
For more information about the I/O settings of the controller, refer to the user manual of the controller.
Card reading is not available while the buzzer control is sounding the buzzer.
Tamper Control
You can set the signal that you want to output if the device is dismantled forcibly.
Connect the COM port (Pink line) of the product’s tamper switch to GND; connect the NC port (Light yellow) of the
tamper switch to the input port of the controller. If the tamper of the reader operates, the controller produces an input
signal and generates the corresponding output depending on the controller setting.
12_ initialization
output format
WIEGAND OUTPUT
Timing Diagram
5V
1ms
DATA-0
0V
5V
DATA-1
LOGIC
n-2
n-1
0V
n *n : 34 or26
Data Type (26-bit)
•
•
•
•
Bit 1 : Even Parity (bit 2 ~ bit 13)
Bit 2 ~ 9 : Facility Code (000 ~ 255)
Bit 10 ~ 25 : ID Number (00000 ~ 65,535)
Bit 26 : Odd Parity (bit 14 ~ bit 25)
English _ 13
OUTPUT FORMAT
100us
output format
RS-232 OUTPUT
Output Waveform
LSB
+15V
MSB
Space(=0)
+3V
Indeterminate
Region
0V
-3V
Mark(=1)
8 Data Bits
-15V
2 Stop Bits
Start Bit
Data packet corresponding to ASCII character ‘A’
Data Type
START (0X02H)
DATA (8 Char)
END (0x03H)
LRC
START(0X02H)
DATA (1~8 Char)
END (0x03H)
LRC
 Check the following settings:
Baud Rate : 9600bps
Data Bit : 8
Parity Bit : None
Stop Bit : 1
 LRC : This is the result of XOR operation of each byte from Start to End.
14_ output format
8 BIT BURST OUTPUT FORMAT
8Bit Burst Output Format
Binary
Hexa
Keypads
Binary
Hexa
11110000
F0
10010110
96
11100001
E1
10000111
87
11010010
D2
01111000
78
11000011
C3
01101001
69
10110100
B4
ESC
01011010
5A
10100101
A5
ENT
01001011
4B
English _ 15
OUTPUT FORMAT
Keypads
troubleshooting
TROUBLESHOOTING
If the product does not function properly, please see the below for trouble shooting.
PROBLEM
SOLUTION
My card is not read properly.
1)
2)
When I turn on the product, it sounds a
beep with dimly turned on indicator.
1)
Check the rated voltage specified in the user manual and the catalog.
Ensure that the card must comply with the PSK (125KHz) format provided by
Samsung.
- Cards of 13.56MHz format can not be used.
(Contact the card retailer regarding the card format.)
3) If the problem persists, contact the nearest customer service for your
assistance.
2)
3)
The read range (R/R) of the card differs
each time the product reads the card.
1)
2)
16_ troubleshooting
Ensure that you are using a larger-capacity adaptor than specified in the user
manual or the catalog, which should cover the rated current consumption of the
reader. If you are using multiple readers that are connected to one adaptor,
make sure that the adaptor should be large enough to cover the current
consumption multiplied by the reader count.
Even with a large adaptor enough to supply adequate power, if the power cable is
not a dedicated line (such as communication line or UPT cable), or if it’s so long to
cause power loss, you’d better replace it with a dedicated line or reinforce it.
If the problem persists, contact the nearest customer service for your
assistance.
The characteristics of a card are determined by the nature of the coils used and in the
manufacturing process engaged by the card manufacturer. So what you do first is to check
that the cards in use are made by the same manufacturer.
If you are using cards from different card makers, the read range (R/R) differs by
the card, which is the result of normal operation.
If you encounter a different read range for each card that is made by the
same manufacturer, please contact the nearest customer service.
product specifications
PRODUCT SPECIFICATIONS
Item
SSA-R2000V
Power / Current
DC 12V / Max.230mA
Reading Time (Card)
30ms
Input Port
2 ea : External LED Control, External Buzzer Control
Output Port
26bit Wiegand, 8bit Burst for PIN (Selectable)
LED Indicator
3 LED Indicators (Red, Green and Orange)
Beeper
Piezo Buzzer
Keypad
12 Key Touch Keypad with Back Lighting
Operating Temperature
-30°C to +50°C
Operating Humidity
10% to 90% Relative Humidity Non-Condensing
Color / Material
Silver with Black/ Polycarbonate & Aluminum Die casting
Dimension (W x H x D(mm))
87.0 x 109.0 x 25.0
Weight
350± 10g
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of
with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate
that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are
not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
English _ 17
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungsecurity.com
www.samsungtechwin.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
P/No. : Z8100239101A

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2010:10:07 18:02:02-07:00
Modify Date                     : 2010:10:07 18:02:02-07:00
Page Count                      : 18
Creation Date                   : 2010:10:08 01:02:02Z
Mod Date                        : 2010:10:08 01:02:02Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : ltsai
Metadata Date                   : 2010:10:08 01:02:02Z
Creator                         : ltsai
Title                           : User Manual_20101005_v1 - Appen.PDF
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NLMSSA-R2000V

Navigation menu