Harbor Freight 10 Ft X 20 Portable Car Canopy Product Manual

: Harbor-Freight Harbor-Freight-10-Ft-X-20-Ft-Portable-Car-Canopy-Product-Manual-723505 harbor-freight-10-ft-x-20-ft-portable-car-canopy-product-manual-723505 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 8

Page 2 For technical questions, please call 1-888-866-5797. Item 60728

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 4

Assembly .................................................... 4

Maintenance ............................................... 6

Parts List..................................................... 7

Warranty ..................................................... 8

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking concerning

Risk of Head Injury. Wear hard hat

during assembly and service.

WARNING marking concerning Risk

of Hand Injury. Wear heavy-duty work

gloves during assembly and service.

Page 3For technical questions, please call 1-888-866-5797.Item 60728

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in serious injury.

Save all warnings and instructions for future reference.

The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible

conditions and situations that may occur. It must be understood by the operator that common sense

and caution are factors which cannot be built into this product, but must be supplied by the operator.

Assembly Precautions

1. Do not assemble in windy conditions.

2. Assemble and install only on

flat, level, hard surface.

3. Assemble and anchor only according to

these instructions. Improper assembly or

inadequate anchoring can create hazards.

4. Check for utility lines, tree branches and

other structures before assembling.

5. Verify that installation surface has no

hidden utility lines before anchoring.

6. Wear ANSI-approved safety goggles,

heavy-duty work gloves and hard hat

during assembly and service.

7. Keep assembly area clean and well lit.

8. Keep bystanders out of the area during assembly.

9. Do not assemble when tired or when under

the influence of drugs or medication.

10. Product capabilities apply to properly and

completely assembled product only.

Use Precautions

1. DO NOT USE IN HIGH WIND. Disassemble and

store if harsh weather or heavy rain threatens.

2. For temporary use only.

Do not use for long-term shelter.

3. Do not use as tent. Does not meet tent

flammability standards. Do not use grill, heater,

or ignition sources inside or near cover.

4. Do not allow snow, rainwater or debris

to accumulate or pool on roof.

5. Do not hang objects from any part of the Canopy.

6. This product is not a toy. Do not allow

children to play with or near this item.

7. Use as intended only.

8. Inspect regularly, tighten all loose hardware and

loose ropes, and secure all loosened anchors.

If any parts are damaged, bent, or stretched, they

must be replaced. Hardware may loosen during

normal operation stresses. Loose hardware

or damaged/altered parts will compromise

the structural integrity of this product.

9. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

SAVE THESE INSTRUCTIONS.

SAFETYMAINTENANCE ASSEMBLY

Page 4 For technical questions, please call 1-888-866-5797. Item 60728

Specifications

Overall Dimensions 10′ W x 20′ L

Center Height 9′ 6"

Side Height 6′ 3"

Pole Diameter 1.34"

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY:

Do not leave this product partially assembled. Assemble this product completely at one time.

Note: At least 2 workers are required for assembly. Before starting assembly, review the instructions and make sure

there is enough time and the proper tools available to properly assemble.

Make sure all parts seat completely and securely. Assemble on a flat, level surface.

1. Lay out six Straight Poles (1), eighteen Swaged Poles (2), six Rafter Poles (3),

six 3-Way Connectors (4), and three 4-Way Connectors (5).

2 2

2

2 2

3 3 3

3 3 3

1 1

44

44

4 45

5

5

11

1 1

2

2

2

2

22

2

2

2 22

22

Figure A: Roof Layout

2. Connect all parts, making sure that crimped tubes insert into plain ends as far as they will go.

Crimped tubes

insert into

plain ends.

Figure B: Roof Assembly

SAFETY MAINTENANCE

ASSEMBLY

Page 5For technical questions, please call 1-888-866-5797.Item 60728

3. Attach a Leg Pole (6) to each of the six remaining

Swaged Poles (2), and add a Foot Plate (7), making

sure the holes in the sides of the Poles are at the top.

4. Starting on one side, insert the Straight Poles

into the Connectors. Repeat on the other side.

6

Connector

Foot Plate

(7)

Hole

Figure C

5. Place the Cover (8) on top of the roof.

Figure D

6. Secure the Cover to the roof by putting the

ends of the Bungee Cords through the eyelets,

around the Pole, and over the balls.

Ball

Bungee

Cord

Eyelet

Pole

Figure E

7. On each corner, wrap the roof rope around

the pole several times until all slack is taken

up, then secure the S-Hook in the hole.

Roof

Rope

S-Hook

Figure F

8. WARNING! Verify that installation surface has no

hidden utility lines before driving Spike Anchors.

9. Cut the Guy Rope (10) into 4 equal lengths.

10. Drive a Spike Anchor (11) about 3 feet

away from each corner, angled inward.

11. On each corner:

a. Tie one end of the Guy Rope securely

to the 3-Way Connector.

b. Thread the other end of the Guy Rope through

the loop on the Spike Anchor, take up all slack,

then tie a secure knot while under tension.

Guy

Rope

Spike

Anchor

Figure G

WARNING! The Cover must be installed and

anchored. The Cover, Guy Ropes and Spike Anchors do

not only anchor the Canopy, they also hold it together.

2

SAFETYMAINTENANCE ASSEMBLY

Page 6 For technical questions, please call 1-888-866-5797. Item 60728

Maintenance

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM PRODUCT FAILURE:

Do not use damaged products. If damage is noted, have the problem corrected before further use.

Inspection

MONTHLY, inspect the general condition of the Canopy. Check for:

• loose spike anchors, pole connections, or bungee cords (tighten as needed),

• torn or frayed roof or ropes,

• cracked, bent, or broken parts, and

• any other condition that may affect its safe operation.

Cleaning

1. Immediately remove any accumulated debris from the

roof with a broom, mop, or other soft-sided instrument

from the outside. DO NOT use sharp instruments.

2. PERIODICALLY, clean roof with mild soap and water.

DO NOT use bleach or harsh abrasive products.

SAFETY MAINTENANCE

ASSEMBLY

Page 7For technical questions, please call 1-888-866-5797.Item 60728

Parts List

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Note: Individual part illustrations not to scale.

Part Description Illustration Qty

1Straight Pole 40" 6

2 Swaged Rafter 40-3/4" 24

3 Rafter 24-5/8" 6

4 3-Way Connector 6

5 4-Way Connector 3

6Leg Pole 39" 6

7 Foot Plate 6

8 Cover 1

9 Ball Bungee Cord 24

10 Guy Rope 40' 1

11 Spike Anchor 4

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

SAFETYMAINTENANCE ASSEMBLY

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.