Harbor Freight 1 2 In Drive Digital Torque Adapter Product Manual

: Harbor-Freight Harbor-Freight-1-2-In-Drive-Digital-Torque-Adapter-Product-Manual-723909 harbor-freight-1-2-in-drive-digital-torque-adapter-product-manual-723909 harbor-freight pdf

Open the PDF directly: View PDF .
Page Count: 6

1/2ʺ Drive Digital Torque Adapter

68283 1/2” Drive Digital Torque Adapter

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged. If any parts

are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Page 2For technical questions, please call 1-800-444-3353.SKU 68283

Specications

Drive Size 1/2”

Accuracy + 2%

Included

Adapters

1/2” - 3/8”

1/2” - 1/4”

Torque Range 29.5 ft-lb. to 147.5 ft-lb.

Auto

Shutdown After 80 Seconds

Memory Stores up to 50 torque readings

Battery One 3-volt CR2032 button cell battery

(Included)

Save This Manual

Keep this manual for the safety warnings and precautions,

assembly, operating, inspection, maintenance and

cleaning procedures. Write the product’s serial

number in the back of the manual near the assembly

diagram (or month and year of purchase if product

has no number). Keep this manual and the receipt

in a safe and dry place for future reference.

Important Safety Information

In this manual, on the labeling, and all other

information provided with this product:

This is the safety alert symbol. It is used

to alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

CAUTION, used with the safety alert symbol,

indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE is used to address practices

not related to personal injury.

CAUTION, without the safety alert symbol, is used

to address practices not related to personal injury.

General Safety Warnings

WARNING Read all safety warnings and

instructions. Failure to follow the warnings and

instructions may result in serious injury.

Save all warnings and instructions

for future reference.

1. Do not exceed the Digital Torque

Adapter’s max. torque value.

2. Position battery in proper polarity and do

not install battery of different type.

3. Do not submerge Digital Torque Adapter.

4. Do not disassemble Digital Torque Adapter.

5. Do not expose the Digital Torque Adapter to

extreme temperature, humidity, or direct sunlight.

6. Do not excessively shake Digital Torque Adapter.

7. This product is not a toy. Keep it

out of reach of children.

8. The warnings, precautions, and instructions discussed

in this instruction manual cannot cover all possible

conditions and situations that may occur. It must

be understood by the operator that common sense

and caution are factors which cannot be built into

this product, but must be supplied by the operator.

SAVE THESE

INSTRUCTIONS.

DANGER indicates a hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if

not avoided, could result in death or serious injury.

Page 3For technical questions, please call 1-800-444-3353.SKU 68283

Instructions for Putting into Use

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning

of this manual including all text

under subheadings therein before

set up or use of this product.

Note: For additional information regarding the

parts listed in the following pages, refer to Parts List

and Assembly Diagram on page 4.

Functions

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning

of this manual including all text under

subheadings therein before set up or use of

this product

1. Securely fasten Adapter to ratchet.

2. Attach an adapter to end of anvil, if desired.

Once fastened, press the Power button

to activate the Adapter. The LCD Display

will show “trACE” and “PtoP.”

3. After two seconds, the Display will show “00.0”.

4. Swing the Adapter. The Display will

show the measured torque.

5. Note: If you do not use the Adapter for 80

seconds, the Adapter will automatically shut off.

6. Press the Memory (“M”) button and the “P/T” button

at the same time to select the desired torque unit.

7. The Adapter contains three unit

selections: kg-m, ft-lb and N-m.

8. To increase the current torque value, press and hold

down the Increase (“+”) button until value is reached.

9. To lower the current torque value, press and hold

down the Decrease (“-”) button until value is reached.

10. Note: The Display will show “00.0” if no

selection is made after ten seconds.

11. During operation, the LED light will ash GREEN.

12. Once you are 20% away from targeted torque, the

LED will ash YELLOW and the buzzer will beep.

13. When targeted torque is reached, the LED will

change to RED and a long buzz will sound.

14. To set peak torque, press and release the

“P/T” button when Adaptor is on.

15. The Display will show “PtoP” and

then “00.0” two seconds later.

16. To trace torque setting, press and

release the “P/T” button.

17. The Display will show “trACE” and

then “00.0” two seconds later.

18. To store a torque reading, have the digital torque

wrench in “PtoP” mode. When you use it, the torque

wrench can store the reading automatically.

19. Press the Memory button. The Display Panel

will show the stored reading as “P01”.

20. To show the second stored reading, press the

Memory button again for one second. The second

torque value will be designated as “P02”.

21. You can continue to store settings until you

reach fty saved settings, or “P50”.

Decrease

Torque

Increase

Torque

Memory

PowerPeak and Trace

LED

Light

Anvil

Display

Page 4For technical questions, please call 1-800-444-3353.SKU 68283

22. Note: “P50” will be the most recent saved

setting while “P01” will be the oldest.

23. If the torque setting is exceeded by 125% of the full

scale, the LED will ash RED and the alarm will beep.

24. WARNING! Do not press the Memory and

Power buttons at the same time. This will

calibrate the tool and alter the preset values.

25. To turn off the Adapter, press the Power button OR wait

80 seconds for the Adapter to turn off automatically.

26. Clean, then store the tool indoors

out of children’s reach.

Maintenance and Servicing

Procedures not specically explained

in this manual must be performed

only by a qualied technician.

Replacing Batteries

1. NOTE: When battery power is low, a “ ” icon

will appear on the display screen. Battery life will

depend on battery quality and amount of hours

tool is used. Typical battery life is 110 hours.

2. To replace battery, remove Battery Cap.

3. Remove old battery.

4. Install new CR2032 button cell battery, making sure to

follow indicated polarity (the “+” should face upwards).

5. Replace Battery Cap.

6. Remove the battery if Torque Adapter

will be stored for a long time.

Cleaning, Maintenance,

and Lubrication

1. BEFORE EACH USE, inspect the general condition

of the tool. Check for loose hardware, misalignment

or binding of moving parts, cracked or broken

parts, damaged electrical wiring, and any other

condition that may affect its safe operation.

2. AFTER USE, wipe external surfaces

of the tool with clean cloth.

3. Do not use cleaning agents to clean the plastic parts

of the tool. Use only a mild detergent or a damp

cloth. Do not let water come into contact with tool.

Part Description Qty.

1 Upper Housing 1

2 Control Panel 1

3 Display Panel 1

4 LED 1

5 Circuit Board 1

6 Adapter 1

7Ratchet Gauge 1

Part Description Qty.

8 Buzzer 1

9 Lower Housing 1

10 Screw 10

11 Battery Holder 1

12 Battery 1

13 Battery Cap 1

Parts List

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN

THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS

TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE

MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES

ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT

PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

Page 5For technical questions, please call 1-800-444-3353.SKU 68283

Assembly Diagram

1

2

3

4

5

6

7

8

9

10

11

10

12

13

Page 6For technical questions, please call 1-800-444-3353.SKU 68283

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353